Instruction Manual for MARSAIL models including: TZEDS1, TZEDS1B1, TZEDS1N, TZEDS1 Adjustable Height Electric Standing Desk, Height Electric Standing Desk, Electric Standing Desk, Standing Desk
Marsail Adjustable Height Electric Standing Desk, Sit Stand Desk with Additional Desk Stand, 28''-47'' Lifting Range Stand up Desk Memory Sit Stand Up Computer Workstation for Home Office
Installation Manual (PDF) Marsail Marsail,Electric,Standing,Desk,with,Monitor,Stand,with,28"-47",Lifting,Range,,Adjustable,Height,Sit,Stand,Desk,,Standing,Desk,for,Home,Office,,Gaming,,and,Work,,
Installation Manual (PDF) Marsail Marsail,Electric,Standing,Desk,with,Monitor,Stand,,Adjustable,Height,Sit,Stand,Desk,,28"-47",Lifting,Range,,Standing,Desk,for,Home,Office,,Gaming,,and,Working,,
Electric Standing Desk Instruction Manual (A) Model: TZEDS1/TZEDS1B1/TZEDS1N Thank you for choosing this product! We strive to provide you with the best quality products and services in the industry. Should you have any issues, please don't hesitate to contact us Technical Support: 877-546-8648 Mon-Fri 8am - 8pm(CST) Other Info: support@ciays.com Specification Vertical Range: 28.3 - 47.2 in (72-120cm) RATED Power Input Max.Speed Motion Noise Load Capacity 110V-240V 25 mm/s 55dB 176 lbs / 80 kg Supplied Parts and Hardware for Step 1 Crossbar 02 (x1) Left Table Leg 05 (x1) Right Table Leg 06 (x1) Leg Base 07 (x2) Bolt M6×35 mm A (x8) Bolt M8×47 mm C (x4) 3/16 in (5mm) Large Allen Key E (x1) Supplied Parts and Hardware for Step 2 Foot H (x4) Side Plate 03 (x2) Transmission Rod 04 (x1) Bolt M6×10 mm B (x4) 5/32 in (4mm) Medium Allen Key F (x1) 5/64 in (2mm) Small Allen Key G (x1) Rubber Pad J (x10) Supplied Parts and Hardware for Step 3 Desktop 01 (x2) Tabletop Connector 08 (x3) Supplied Parts for Step 4 Controller 12 (x1) Headset Hook 13 (x1) Screw M5x16mm D (x23) Wall Plug Power 09 (x1) Cable Clip I (x2) 01 Screw M4x20mm M (x2) Wooden Pin N (x2) Supplied Parts for Step 5 Small Desktop 10 (x1) Bracket 11 (x2) Bolt M5×12 mm K (x6) M20×1 mm L (x4) Step 1 Assemble the Leg Bases and Crossbar E Large Allen Key 07 05 A H 07 06 02 05 06 02 E C Large Allen Key 06 02 Step 2 Secure the Side Plates and Transmission Rod to the Table Legs 2-1 Side Plate B 03 Left Table Leg Leg Base 2-2 1 2 Right Table Leg F Medium Allen Key Coupling nut 04 03 Loosen the pre-assembled coupling nut for adjusting the length. 04 05 Insert the transmission rod on the left leg into the hex hole and turn the transmission rod anti-clockwise until the left leg goes to the lowest position. 03 3 Insert the other end of transmission rod to the slot on the right leg (You may rotate the rod slightly for better installation). 4 G G Small Allen Key Secure the transmission rod to the slot by tightening the pre-assembled set screw clockwise using the small Allen key [G]. 5 J Tighten the coupling nut. 04 How to Solve the Problem of Different Heights of Two Table Legs Step 1. Measure whether the height of the two table legs are the same using a measuring tape before installation. Install Transmission Rod: Please fine-tune the transmission rod. Turn clockwise Left Leg Step 3. If the height of the left table leg is lower than the right table leg, insert the transmission rod into the hexagonal hole of the left table leg and rotate the transmission rod clockwise to fine-tune the left table leg to make the left table leg as high as the right table leg. Turn anti-clockwise Left Leg Step 2. If the height of left table leg is higher than the right table leg, insert the transmission rod into the hexagonal hole of the left leg, then rotate the transmission rod anti-clockwise to fine-tune the left leg to make the left table leg as high as the right table leg. Step 3 Secure the Desktop to the Stand Assemble the desktop. Phillips Screwdriver [Not Included] N 01 01 Soft Cloth D 08 05 Attach the leg assembly, controller and hook to Phillips the desktop. Screwdriver 13 [Not Included] Right Table Leg Soft Cloth Can be mounted in each side M 12 Step 4 Connect the Cables 09 Duty Cycle: 10%, 2 min on/18 min off The pre-assembled cable on the motor. Self-supplied USB cable Built-in USB Port for charging 09 your device. 06 Step 5 Place the Monitor Stand on the Desktop 5-1 11 10 K 11 Phillips Screwdriver [Not Included] 5-2 L 5-3 07 Short press [S] button, the display flashes. Press either of 1,2,3 memory keys to save the height. Press button, and the desk will move to the certain height that was previously set for memory 1. Press button, and the desk will move to the certain height that was previously set for memory 2. Press button, and the desk will move to the certain height that was previously set for memory 3. Reset 08 09 Thank you again for choosing this product! All of us do appreciate your product purchase. We hope that you are as happy with your product as we are designing and manufacturing it for you. We strive to provide you with the best quality products and services in the industry. Should you have any issues, please don't hesitate to contact us Technical Support: 877-546-8648 Mon-Fri 8am - 8pm(CST) Other Info: support@ciays.com 860-00046-00 Rev00Adobe PDF library 15.00 Adobe Illustrator(R) 24.0