TELEC [PDF] RADIO TEST REPORT For ankbit international Limited ...

TELEC

LEO

[PDF] RADIO TEST REPORT For Shenzhen ankbit international Limited ...

: Bluetooth transmitter and receiver 2-in-1. Trade Mark.................................. : 1Mii. Test Model.................................. : ML301. Ratings ...

Google Docs
Google Drive
Download [pdf]

File Info : application/pdf, 20 Pages, 902.50KB

219-229207 02 007

Page 1 of 20

Report No.: LCSA082322016EB

RADIO TEST REPORT For
Shenzhen ankbit international Limited Bluetooth transmitter and receiver 2-in-1
Test Model: ML301 Additional Model No.: Please Refer to Page 6

Prepared for Address

: Shenzhen ankbit international Limited : Runfeng industrial Park, 4197 Baoan Blvd, Xixiang St,
Baoan Dist, Shenzhen, China

Prepared by Address
Tel Fax Web Mail

: Shenzhen LCS Compliance Testing Laboratory Ltd. : Room 101, 201, Building A and Room 301, Building C,
Juji Industrial Park, Yabianxueziwei, Shajing Street, Bao'an District, Shenzhen, Guangdong, China : (+86)755-82591330 : (+86)755-82591332 : www.LCS-cert.com : webmaster@LCS-cert.com

Date of receipt of test sample Number of tested samples Serial number Date of Test Date of Report

: August 24, 2022 :2 : Prototype : August 24, 2022 ~ September 08, 2022 : September 09, 2022

Shenzhen LCS Compliance Testing Laboratory Ltd. Add: Room 101, 201, Building A and Room 301, Building C, Juji Industrial Park, Yabianxueziwei, Shajing Street, Bao'an District, Shenzhen, Guangdong, China Tel: +(86) 0755-82591330 | E-mail: webmaster@lcs-cert.com | Web: www.lcs-cert.com Scan code to check authenticity

Page 2 of 20

Report No.: LCSA082322016EB

RADIO TEST REPORT MIC Notice No.88 Appendix No. 43
Second-Generation Low-Power Data Communication System/Wireless LAN System
Report Reference No. .............: LCSA082322016EB
Date of Issue............................... : September 09, 2022
Testing Laboratory Name...... : Shenzhen LCS Compliance Testing Laboratory Ltd. Address........................................ : Room 101, 201, Building A and Room 301, Building C, Juji
Industrial Park, Yabianxueziwei, Shajing Street, Bao'an District, Shenzhen, Guangdong, China Testing Location/ Procedure.... : Full application of Harmonised standards Partial application of Harmonised standards Other standard testing method
Applicant's Name..................... : Shenzhen ankbit international Limited Address........................................ : Runfeng industrial Park, 4197 Baoan Blvd, Xixiang St,
Baoan Dist, Shenzhen, China Test Specification Standard...................................... : MIC Notice No.88 Appendix No.43 Test Report Form No.............. : LCSEMC-1.0 TRF Originator............................ : Shenzhen LCS Compliance Testing Laboratory Ltd. Master TRF................................. : Dated 2011-03 Shenzhen LCS Compliance Testing Laboratory Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen LCS Compliance Testing Laboratory Ltd. is acknowledged as copyright owner and source of the material. Shenzhen LCS Compliance Testing Laboratory Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context.
Test Item Description............. : Bluetooth transmitter and receiver 2-in-1 Trade Mark.................................. : 1Mii
Test Model.................................. : ML301 Ratings......................................... : Input: DC 5V, 1A
DC 3.7V, 250mAh for Battery Result ...........................................: Positive

Compiled by:

Supervised by:

Approved by:

Rory Huang/ Administrator

Cary Luo/ Technique principal

Gavin Liang/ Manager

Page 3 of 20

Report No.: LCSA082322016EB

RADIO -- TEST REPORT

Test Report No. : LCSA082322016EB

September 09, 2022
Date of issue

Test Model...............................

: ML301

EUT........................................ : Bluetooth transmitter and receiver 2-in-1

Applicant............................... : Shenzhen ankbit international Limited

Address..................................
Telephone.............................. Fax.........................................

: Runfeng industrial Park, 4197 Baoan Blvd, Xixiang St, Baoan Dist, Shenzhen, China
:/ :/

Manufacturer........................ : Shenzhen ankbit international Limited Address.................................. : Runfeng industrial Park, 4197 Baoan Blvd, Xixiang St, Baoan
Dist, Shenzhen, China Telephone.............................. : / Fax......................................... : /
Factory.................................. : Shenzhen ankbit international Limited Address.................................. : Runfeng industrial Park, 4197 Baoan Blvd, Xixiang St, Baoan
Dist, Shenzhen, China Telephone.............................. : / Fax......................................... : /

Test Result

Positive

The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory.

Page 4 of 20

Report No.: LCSA082322016EB

Report Version 000

Revision History

Issue Date September 09, 2022

Revision Content Initial Issue

Revised By ---

Page 5 of 20

Report No.: LCSA082322016EB

TABLE OF CONTENTS
1. GENERAL INFORMATION ........................................................................................................................ 6 1.1. DESCRIPTION OF DEVICE (EUT) ............................................................................................................. 6 1.2. HOST SYSTEM CONFIGURATION LIST AND DETAILS ................................................................................. 7 1.3. EXTERNAL I/O CABLE ............................................................................................................................. 7 1.4. DESCRIPTION OF TEST FACILITY ............................................................................................................. 7 1.5. TEST CONDITIONS .................................................................................................................................. 7 1.6. FREQUENCY OF CHANNELS .....................................................................................................................7
2. TEST METHODOLOGY ..............................................................................................................................8 2.1. EUT EXERCISE ...................................................................................................................................... 8 2.2. MEASUREMENT UNCERTAINTY ................................................................................................................ 8 2.3. TABLE FOR PARAMETERS OF TEST SOFTWARE SETTING ......................................................................... 8 2.4. DESCRIPTION OF TEST MODES ............................................................................................................... 8 2.5. TEST VOLTAGE .......................................................................................................................................9
3. SYSTEM TEST CONFIGURATION ..........................................................................................................10 3.1. JUSTIFICATION ......................................................................................................................................10 3.2. EUT EXERCISE SOFTWARE .................................................................................................................. 10 3.3. SPECIAL ACCESSORIES ........................................................................................................................ 10 3.4. BLOCK DIAGRAM/SCHEMATICS ..............................................................................................................10 3.5. EQUIPMENT MODIFICATIONS ................................................................................................................. 10
4. SUMMARY OF TEST RESULTS ..............................................................................................................11
5. TEST RESULT .......................................................................................................................................... 12 5.1. FREQUENCY TOLERANCE ......................................................................................................................12 5.2. ANTENNA POWER ................................................................................................................................. 13 5.3. OCCUPIED FREQUENCY BANDWIDTH ..................................................................................................... 14 5.4. SPREAD BANDWIDTH ............................................................................................................................ 15 5.5. TRANSMITTER SPURIOUS EMISSIONS (CONDUCTED) .............................................................................. 16 5.6. CARRIER SENSING FUNCTION ................................................................................................................ 17 5.7. INTERFERENCE PREVENTION FUNCTION ................................................................................................. 18 5.8. SECONDARY RADIATED EMISSIONS ....................................................................................................... 19
6. PHOTOGRAPHS OF TEST SETUP .........................................................................................................20
7. EXTERNAL PHOTOGRAPHS OF THE EUT ........................................................................................... 20
8. INTERNAL PHOTOGRAPHS OF THE EUT ............................................................................................ 20
9. LIST OF MEASURING EQUIPMENTS .....................................................................................................20

Page 6 of 20

Report No.: LCSA082322016EB

1. GENERAL INFORMATION

1.1. Description of Device (EUT)

EUT

: Bluetooth transmitter and receiver 2-in-1

Test Model

: ML301

Additional Model No.
Model Declaration Power Supply Hardware Version

: ML301+, ML301Pro, ML301Pro+, ML302, ML302+, ML 302Pro, ML302Pro+, RT238, RT6007Q1, ML300, ML300+, ML300Pro, ML300Pro+, RT239
: PCB board, structure and internal of these model(s) are the same, So no additional models were tested
: Input: DC 5V, 1A DC 3.7V, 250mAh for Battery
: V1.0

Software Version

: V1.0

Bluetooth

Frequency Range

Declared Antenna Power :

Modulation Technology :

Data Rate

Antenna Description

2402-2480MHz for Bluetooth (79 channels for Bluetooth V5.2(BDR/EDR) Channel Frequency=2402+(K-1), K=1, 2, 3 ......79 40 channels for Bluetooth V5.2(BT LE/BT 2LE) Channel Frequency=2402+2(K-1), K=1, 2, 3 ......40 Bluetooth V5.2(BDR/EDR): 0.10mW/MHz Bluetooth V5.2(BT LE/BT 2LE): 3.0mW Bluetooth V5.2(BDR/EDR): GFSK, /4-DQPSK, 8-DPSK Bluetooth V5.2(BT LE/BT 2LE): GFSK Bluetooth V5.2(BDR/EDR): 1/2/3Mbps Bluetooth V5.2(BT LE/BT 2LE): 1/2Mbps PCB Antenna, 2.0dBi(Max.)

Page 7 of 20

Report No.: LCSA082322016EB

1.2. Host System Configuration List and Details

Manufacturer ---

Description ---

Model ---

Serial Number ---

Certificate ---

1.3. External I/O Cable

I/O Port Description Earphone Jack Type-C Port

Quantity 1 1

Cable Cable: 0.15m, unshielded Cable: 0.3m, unshielded

1.4. Description of Test Facility
FCC Registration Number is 254912. NVLAP Accreditation Code is 600167-0. FCC Designation Number is CN5024. CAB identifier is CN0071. CNAS Registration Number is L4595. Industry Canada Registration Number is 9642A.

1.5. Test Conditions

Temperature Range

Humidity Range

Pressure Range

21-25 45-85% 86-106kPa

1.6. Frequency of Channels

Bluetooth V5.2 (BT LE/BT 2LE)

Channel

Frequency(MHz)

2402

2404

2406

---

2438

2440

Channel 21 ----38 39 40

Frequency(MHz) 2442 ----2476 2478 2480

Page 8 of 20

Report No.: LCSA082322016EB

2. TEST METHODOLOGY

2.1. EUT Exercise

The EUT was operated in the engineering mode to fix the TX frequency that was for the purpose of the measurements. According to its specifications, the EUT must comply with the requirements of MIC Notice No.88 Appendix No. 43.

2.2. Measurement Uncertainty

Test Item

Remark

Bandwidth

+/- 0.2 E-6

Antenna Power

+/-0.33dB

Frequency Tolerance

+/- 0.3 E-6

Conducted spurious emission :

+/-0.13dB

DC Power

+/-1%

(1). This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2.

2.3. Table for Parameters of Test Software Setting

During testing, Channel & Power Controlling Software provided by the customer was used to control the operating channel as well as the output power level. The RF output power selection is for the setting of RF output power expected by the customer and is going to be fixed on the firmware of the final end product.

Power Parameters:
Test Software Version Frequency
Bluetooth V5.2(DTS)

2402MHz Default

BlueTest3 2440MHz Default

2480MHz Default

2.4. Description of Test Modes

Tested mode, channel, and data rate information

Mode

Preliminary Test Data Rate (Mbps)

Final Test Data Rate (Mbps)
(see Note)

Channel

Frequency (MHz)

Bluetooth

Low :CH1

2402

V5.2

Middle: CH20

2440

(BT LE/BT

2LE)

High: CH40

2480

Note: According exploratory test, EUT will have maximum output power in those data rate, so

those data rate were used for all test.

Page 9 of 20

Report No.: LCSA082322016EB

2.5. Test Voltage

POWER SUPPLY VOLTAGE FLUCTUATION TEST

Voltage Fluctuation Test

Normal Voltage

High Voltage +10% of Normal Voltage

Low Voltage -10% of
Normal Voltage

Input To EUT

DC 5.0V

DC 5.5V

DC 4.5V

Output To RF Module
Voltage Variation (%)

DC 3.3V --

Note:
As the EUT was powered by DC 5.0V, and with the voltage stabilizing circuit used, the chip voltage received floating not exceed ±1% of nominal condition when working on extreme voltage, so all test performed at nominal voltage only.

Page 10 of 20

Report No.: LCSA082322016EB

3. SYSTEM TEST CONFIGURATION

3.1. Justification
The system was configured for testing in engineering mode.

3.2. EUT Exercise Software
The system was configured for testing in a continuous transmits condition and change test channels by software (input command.) provided by application.

3.3. Special Accessories
N/A.

3.4. Block Diagram/Schematics
Please refer to the related document.

3.5. Equipment Modifications
Shenzhen LCS Compliance Testing Laboratory Ltd. has not done any modification on the EUT.

Page 11 of 20
4. SUMMARY OF TEST RESULTS

Report No.: LCSA082322016EB

MIC Notice No.88 Appendix No.43 Article 2 Paragraph 1 Item 19

Clause

Description of Test (Transmitter Parameters)

Result

Frequency Tolerance

PASS

Antenna Power

PASS

Tolerances for Antenna Power

PASS

Transmission Rate

PASS

Occupied Frequency Bandwidth

PASS

Spread Bandwidth

PASS

Dwell Time

N/A

Spurious Emissions

PASS

Transmission Antenna Gain

N/A

(EIRP Antenna Power)

Transmission Radiated Angle Width

N/A

(3dB Beam width)

Interference prevention function

PASS

Carrier Sensing function

N/A

Receiver Parameters

Secondary Radiated Emissions

PASS

Note: (1) N/A is an abbreviation for Not Applicable.
(2) N/T means this test item is not tested.

Page 12 of 20

Report No.: LCSA082322016EB

5. TEST RESULT

5.1. Frequency Tolerance
5.1.1. Standard Applicable Tolerance of frequency shall be ±50x10-6.

5.1.2. Test Procedures a. Set EUT work in test mode as described in clause 2.4. b. Connected the EUT's antenna port to the Spectrum Analyzer by suitable
attenuator, set the Spectrum Analyzer as below: Centre Frequency: The centre frequency of the channel under test. Resolution BW: 10 KHz. Video BW: 10 KHz. Span: 1MHz. Detector: Peak. Trace Mode: Max Hold.
c. When the trace is complete, find the peak value of the power envelope and record.

5.1.3. Test Setup Layout

5.1.4. EUT Operation during Test The EUT was programmed to be in continuously transmitting mode.
5.1.5. Test Result Please refer to the Appendix B.1 for BT LE/BT 2LE RF Test Data.

Page 13 of 20

Report No.: LCSA082322016EB

5.2. Antenna Power
5.2.1. Standard Applicable
Type DTS OFDM OBW<26MHz, DS OFDM OBW 26-40MHz Tolerance

Limit 10mW 10mW/MHz 5mW/MHz +20%,-80%

5.2.2. Measuring Instruments Please refer to section 6 of equipments list in this report.

5.2.2. Test Procedures
a. EUT have transmitted continuous maximum power
b. Antenna Power Error is definition that actual measure antenna power tolerance between +20% to -80% power range that base on manufacturer declare the conducted power density.

5.2.3. Test Setup

5.2.4. EUT Operation during Test The EUT was programmed to be in continuously transmitting mode.
5.2.5. Test Result Please refer to the Appendix B.2 for BT LE/BT 2LE RF Test Data.

Page 14 of 20

Report No.: LCSA082322016EB

5.3. Occupied Frequency Bandwidth
5.3.1. Standard Applicable
Permissible value for occupied bandwidth using the FH system, a hybrid system combining DS and FH systems, or a hybrid system combining FH and OFDM systems shall be 83.5 MHz or less, while necessary bandwidth (minimum occupied bandwidth sufficient to ensure information transmission of required quality at a required transmission rate for the system used under specified conditions for a given emission type) using a system other than any of the above shall be 26 MHz or less.

5.3.2. Test Procedures a. Set EUT work in test mode as described in clause 2.4. b. Connected the EUT's antenna port to the Spectrum Analyzer by suitable
attenuator, set the Spectrum Analyzer as below: Centre Frequency: The centre frequency of the channel under test. RBW/VBW= 30KHz/30KHz Span: Wide enough to cover the complete power envelope of the signal of the
EUT. Sweep mode: Continuous sweeping. Detector: Peak. Trace Mode: Max Hold.
c. When the trace is complete, measure the occupied bandwidth (99% bandwidth) with spectrum analyzer's bandwidth measure function.
5.3.3. Test Setup Layout

5.3.4. EUT Operation during Test The EUT was programmed to be in continuously transmitting mode.
5.3.5. Test Result of 99% Spectrum Bandwidth Please refer to the Appendix B.3 for BT LE/BT 2LE RF Test Data.
Shenzhen LCS Compliance Testing Laboratory Ltd. Add: Room 101, 201, Building A and Room 301, Building C, Juji Industrial Park, Yabianxueziwei, Shajing Street, Bao'an District, Shenzhen, Guangdong, China Tel: +(86) 0755-82591330 | E-mail: webmaster@lcs-cert.com | Web: www.lcs-cert.com Scan code to check authenticity

Page 15 of 20

Report No.: LCSA082322016EB

5.4. Spread Bandwidth
5.4.1. Standard Applicable In spread spectrum systems, spread bandwidth (which refers to a frequency bandwidth with an upper limit and lower limit such that each of the mean powers radiated above the upper frequency limit and below the lower frequency limit is equal to 5 % of the total mean power radiated; this also applies hereafter) shall be 500 kHz or more.
5.4.2. Test Procedures a. Set EUT work in test mode as described in clause 2.4. b. Connected the EUT's antenna port to the Spectrum Analyzer by suitable
attenuator, set the Spectrum Analyzer as below: Centre Frequency: The centre frequency of the channel under test. RBW/VBW= 30KHz/30KHz Span: Wide enough to cover the complete power envelope of the signal of the
EUT. Detector: Peak. Trace Mode: Max Hold.
c. When the trace is complete, measure the occupied bandwidth (90% bandwidth) with spectrum analyzer's bandwidth measure function.
5.4.3. Test Setup Layout

5.4.4. EUT Operation during Test The EUT was programmed to be in continuously transmitting mode.
5.4.5. Test Result of 90% Occupied Bandwidth. Please refer to the Appendix B.4 for BT LE/BT 2LE RF Test Data.
Shenzhen LCS Compliance Testing Laboratory Ltd. Add: Room 101, 201, Building A and Room 301, Building C, Juji Industrial Park, Yabianxueziwei, Shajing Street, Bao'an District, Shenzhen, Guangdong, China Tel: +(86) 0755-82591330 | E-mail: webmaster@lcs-cert.com | Web: www.lcs-cert.com Scan code to check authenticity

Page 16 of 20

Report No.: LCSA082322016EB

5.5. Transmitter Spurious Emissions (conducted)

5.5.1. Standard Applicable

Permissible mean power of spurious emission of each frequency supplied to a feeder, that is, mean power of spurious emission in the 1 MHz bandwidth at frequency f other than frequency band used shall be as follows:

a. 30MHz - 1,000MHz

0.25 W or less

b. 1,000MHz - 2,387MHz

2.5 W or less

c. 2,387MHz - 2,400MHz and 2,483.5MHz - 2,496.5MHz

25 W or less

d. 2,496.5MHz - 13GHz

2.5 W or less

5.5.2. Test Procedures a. Set EUT work in test mode as described in clause 2.4. b. Connected the EUT's antenna port to the Spectrum Analyzer by suitable
attenuator, set the Spectrum Analyzer as below: Below 1GHz: RBW/VBW= 100KHz/ 100KHz Above 1GHz: RBW/VBW= 1MHz / 1MHz. Detector: Peak. Trace Mode: Max Hold.
c. All the emissions from 30MHz to 13GHz were measured and record.

5.5.3. Test Setup Layout

5.5.4. EUT Operation during Test The EUT was programmed to be in continuously transmitting mode.
5.5.5. Test Results Please refer to the Appendix B.5 for BT LE/BT 2LE RF Test Data. -Note:SA set to from 2.4965GHz to 13GHz, plot shows from 2.497GHz to 13GHz as of SA's default format.
Shenzhen LCS Compliance Testing Laboratory Ltd. Add: Room 101, 201, Building A and Room 301, Building C, Juji Industrial Park, Yabianxueziwei, Shajing Street, Bao'an District, Shenzhen, Guangdong, China Tel: +(86) 0755-82591330 | E-mail: webmaster@lcs-cert.com | Web: www.lcs-cert.com Scan code to check authenticity

Page 17 of 20

Report No.: LCSA082322016EB

5.6. Carrier sensing function

5.6.1. Standard Applicable

Item Carrier Sense

Limits Good EUT stop RF transmission signal after carrier inject to EUT. (On 22.79+Gr-20*log (f)[dBm] (Gr: dBi; f: MHz) or 100mV/m)

5.6.2. Instruments Setting

The following table is the setting of spectrum analyzer and receiver.

Spectrum Parameter

Setting

Attenuation

Auto

RB / VB

1 MHz

Span

0 MHz

Sweep

Continuous

Detector

Peak

Trigger mode

Video

5.6.3. Test Procedures

1. SSG adjusted the frequency as same as the EUT transmitted signal and emitted the absence of modulation from SSG and power level is (On 22.79+Gr-20*log(f)[dBm] (Gr: dBi; f: MHz). Then turn off the RF signal of SSG. 2. EUT have transmitted the maximum modulation signal and fixed channelize. 3. Setting of SA is following as: RB: 1MHz / VB: 1MHz / SPAN: 50MHz / AT: 10dB /Ref: 0dBm / Sweep time: Auto / Sweep Mode: Continuous sweep / Detect mode: Positive peak. 4. SSG RF Signal On. 5. EUT shall be stop the transmitted any signal and SSG RF Signal Off. Then EUT will be continuous transmitted signal.

5.6.4. Test Setup Layout

5.6.5. EUT Operation during Test
The EUT was programmed to be in normal transmitting mode.
5.6.6. Test Result
Not Applicable.
Shenzhen LCS Compliance Testing Laboratory Ltd. Add: Room 101, 201, Building A and Room 301, Building C, Juji Industrial Park, Yabianxueziwei, Shajing Street, Bao'an District, Shenzhen, Guangdong, China Tel: +(86) 0755-82591330 | E-mail: webmaster@lcs-cert.com | Web: www.lcs-cert.com Scan code to check authenticity

Page 18 of 20

Report No.: LCSA082322016EB

5.7. Interference prevention function
5.7.1. Standard Applicable
Item Identification code

Limits 48 bits

5.7.2. Measuring ID Code Software
PC with NetTool MAC IP List

Setting MAC Scan

5.7.3. Test Procedures
1. In the case that the EUT has the function of automatically transmitting the identification code: a. Transmit the predetermined identification codes from EUT. b. Check the transmitted identification codes with the demodulator.
2. In the case of receiving the identification code: a. Transmit the predetermined identification codes from the counterpart. b . Check if communication is normal. c. Transmit the other signals than predetermined ID codes from the counterpart. d. check if the EUT stops the transmission, or if it displays that identification codes are different from the predetermined ones.
5.7.4. Test Setup Layout

5.7.5. EUT Operation during Test The EUT was programmed to be in normal transmitting mode.

5.7.6. Test Result
EUT ID
32:7F:A9:F1:11:DA

Performance index
Good

Page 19 of 20

Report No.: LCSA082322016EB

5.8. Secondary Radiated Emissions
5.8.1. Standard Applicable The limit on secondary emissions radiated from the receiving equipment within which the function of other radio equipment will not be impaired shall be, in terms of the power of a dummy antenna circuit that has the same electrical constant as the receiving antenna, 4nW or less at a frequency below 1 GHz and 20 nW or less at a frequency of 1 GHz or higher as measured using the circuit
5.8.2. Test Procedures a. Set EUT work in test mode as described in clause 2.4. b. Connected the EUT's antenna port to the Spectrum Analyzer by suitable
attenuator, set the Spectrum Analyzer as below: Resolution BW: 100 KHz for frequency below 1GHz and 1MHz for frequency above 1GHz Video BW: 100 KHz for frequency below 1GHz and 1MHz for frequency above 1GHz Detector: Peak. Trace Mode: Max Hold.
c. All the emissions from 30MHz to 13GHz were measured and record.
5.8.3. Test Setup

5.8.4. EUT Operation during Test The EUT was programmed to be in continuously transmitting mode.
5.8.5. Test Results Please refer to the Appendix B.6 for BT LE/BT 2LE RF Test Data.
Shenzhen LCS Compliance Testing Laboratory Ltd. Add: Room 101, 201, Building A and Room 301, Building C, Juji Industrial Park, Yabianxueziwei, Shajing Street, Bao'an District, Shenzhen, Guangdong, China Tel: +(86) 0755-82591330 | E-mail: webmaster@lcs-cert.com | Web: www.lcs-cert.com Scan code to check authenticity

Page 20 of 20

Report No.: LCSA082322016EB

6. PHOTOGRAPHS OF TEST SETUP

Please refer to separated files Appendix C for Test Setup Photographs

7. EXTERNAL PHOTOGRAPHS OF THE EUT

Please refer to separated files Appendix D for External Photos of EUT

8. INTERNAL PHOTOGRAPHS OF THE EUT

Please refer to separated files Appendix E for Internal Photos of EUT

9. LIST OF MEASURING EQUIPMENTS

Ite m

Equipment

Power Meter

Power Sensor

4 MXA Signal Analyzer

DC Power Supply

Oscilloscope

Manufacturer
R&S R&S R&S Agilent Agilent Tektronix

Model No.
NRVS NRV-Z81 NRV-Z32 N9020A E3642A 46084A/4609A

Serial No.
100444 100458 10057 MY49100060
N/A 140920

Cal Date
2022-06-16 2022-06-16 2022-06-16 2021-11-15 2021-11-15 2022-08-16

Due Date
2023-06-15 2023-06-15 2023-06-15 2022-11-14 2022-11-14 2023-08-15

----------------THE END OF REPORT---------------
Shenzhen LCS Compliance Testing Laboratory Ltd. Add: Room 101, 201, Building A and Room 301, Building C, Juji Industrial Park, Yabianxueziwei, Shajing Street, Bao'an District, Shenzhen, Guangdong, China Tel: +(86) 0755-82591330 | E-mail: webmaster@lcs-cert.com | Web: www.lcs-cert.com Scan code to check authenticity

WPS 文字 PDFsharp 1.50.5147 (www sharp.com)