N323659 man mitre saw DWS782 NA
marciatreece
885911334792 warranty English
· FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely event a safety notification is required under the Federal Consumer Safety Act.
Register online at www.dewalt.com/register.
Three Year Limited Warranty
DEWALT will repair, without charge, any defects due to faulty materials or workmanship for three years from the date of purchase. This warranty does not cover part failure due to normal wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit www.dewalt.com or call 1-800-4-DEWALT (1-800-433-9258). This warranty does not apply to accessories or damage caused where repairs have been made or attempted by others. This warranty gives you specific legal rights and you may have other rights which vary in certain states or provinces.
In addition to the warranty, DEWALT tools are covered by our:
1 YEAR FREE SERVICE DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any time during the first year after purchase.
90 DAY MONEY BACK GUARANTEE If you are not completely satisfied with the performance of your DEWALT Power Tool, Laser, or Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt for a full refund no questions asked. LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in Latin America, see country specific warranty information contained in the packaging, call the local company or see website for warranty information. FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-4-DEWALT (1-800-433-9258) for a free replacement.
Troubleshooting Guide
BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS
TROUBLE! Saw will not start
Saw makes unsatisfactory cuts
Blade does not come up to speed
WHAT'S WRONG?
WHAT TO DO
1. Saw not plugged in 1. Plug in saw.
2. Fuse blown or circuit breaker tripped
3. Cord damaged
4. Brushes worn out
1. Dull blade
2. Blade mounted backwards
3. Gum or pitch on blade
4. Incorrect blade for work being done
1. Extension cord too light or too long
2. Low house current
2. Replace fuse or reset circuit breaker.
3. Have cord replaced by authorized service center.
4. Have brushes replaced by authorized service center or replace them yourself. Refer to Brushes.
1. Replace blade. Refer to Changing or Installing a New Saw Blade.
2. Turn blade around. Refer to Changing or Installing a New Saw Blade.
3. Remove blade and clean with coarse steel wool and turpentine or household oven cleaner.
4. Change the blade type. Refer to Saw Blades under Optional Accessories.
1. Replace with adequate size cord. Refer to Use Proper Extension Cord under Important Safety Instructions.
2. Contact your electric company.
Machine vibrates excessively
Does not make accurate miter cuts
Material pinches blade
1. Saw not mounted securely to stand or work bench
2. Stand or bench on uneven floor
3. Damaged saw blade
1. Miter scale not adjusted correctly
2. Blade is not square to fence
3. Blade is not perpendicular to table
4. Workpiece moving
1. Cutting bowed material
1. Tighten all mounting hardware. Refer to Bench Mounting.
2. Reposition on flat level surface. Refer to Familiarization.
3. Replace blade. Refer to Changing or Installing a New Saw Blade.
1. Check and adjust. Refer to Miter Scale Adjustment under Adjustments.
2. Check and adjust. Refer to Miter Scale Adjustment under Adjustments.
3. Check and adjust fence. Refer to Bevel Square to Table Adjustment under Adjustments.
4. Clamp workpiece securely to fence or glue 120 grit sandpaper to fence with rubber cement.
1. Refer to Bowed Material under Special Cuts.
15
Acrobat Distiller 10.0.0 (Macintosh)