2016 Gold Medal Products Co. Part No. 49397. Instruction Manual. 10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA. Antique Deluxe 60 Special.
Antique Popper | Antique Deluxe 60 Special Popper - Gold Medal #2660GT – Gold Medal Products Co.
Instruction Manual Antique Deluxe 60 Special Model No. 2660GT, 2660GTSV, 2660GV Model 2660GT Model 2660GTSV Model 2660GV 10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA © 2016 Gold Medal Products Co. Part No. 49397 Antique Deluxe 60 Special Poppers Model No. 2660GT, 2660GTSV, 2660GV SAFETY PRECAUTIONS DANGER Machine must be properly grounded to prevent electrical shock to personnel. Failure to do so could result in serious injury, or death. DO NOT immerse any part of this equipment in water. DO NOT use excessive water when cleaning. Keep cord and plug off the ground and away from moisture. Always unplug the equipment before cleaning or servicing. Make sure all machine switches are in the OFF position before plugging the equipment into the receptacle. 008_051514 DANGER Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death. Any alterations to this equipment will void the warranty and may cause a dangerous condition. NEVER make alterations to this equipment. Read the Installation, Operating, and Maintenance Instructions thoroughly before installing, servicing, or operating this equipment. 014_051514 WARNING To avoid burns, DO NOT touch the kettle or any heated surface. DO NOT place or leave objects in contact with heated surfaces. 013_092414 WARNING ALWAYS wear safety glasses when servicing this equipment. 010_010914 WARNING No user serviceable parts inside. Refer servicing to qualified service personnel. 011_051514 WARNING Read and understand operator's manual and all other safety instructions before using this equipment. To order copies of the operator's manual go to gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862 022_060215 Page 2 gmpopcorn.com Antique Deluxe 60 Special Poppers Model No. 2660GT, 2660GTSV, 2660GV SAFETY PRECAUTIONS (continued) WARNING DO NOT allow direct contact of this equipment by the public when used in food service locations. Only personnel trained and experienced in the equipment operation may operate this equipment. Carefully read all instructions before operation. 012_010914 WARNING This machine is NOT to be operated by minors. 007_010914 Note: Improvements are always being made to Gold Medal's equipment. This information may not be the latest available for your purposes. It is critical that you call Gold Medal's Technical Service Department at 1-800-543-0862 for any questions about your machine operations, replacement parts, or any service questions. (Gold Medal Products Co. does not assume any liability for injury due to careless handling and/or reckless operation of this equipment.) Page 3 gmpopcorn.com Antique Deluxe 60 Special Poppers Model No. 2660GT, 2660GTSV, 2660GV INSTALLATION INSTRUCTIONS Inspection of Shipment After unpacking, check thoroughly for any damage which may have occurred in transit. Claims should be filed immediately with the transportation company. The warranty does not cover damage that occurs in transit, or damage caused by abuse, or consequential damage due to the operation of this machine, since it is beyond our control (reference warranty in back of manual). Manual Read and understand the operator's manual and all other safety instructions before using this equipment. To order copies of the operator's manual go to gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862. Model Description 2660GT: 6 oz. Antique Deluxe Popper equipped with a PowerOffTM Control feature. Unit has a gold frame and etched glass. 2660GTSV: 6 oz. Antique Deluxe Popper with a silver vein frame and etched glass. 2660GV: 6 oz. Antique Deluxe Popper with a gold vein frame and etched glass. Items Included with this Unit Aluminum Scoop Measure 6.5 cc Measure 6 oz. Bulb for Cabinet Interior Knobs with Tee Bolts (for Popper Doors) Knob with Screw (for Old Maid Pan) Black Crutch Tips Page 4 gmpopcorn.com Antique Deluxe 60 Special Poppers Model No. 2660GT, 2660GTSV, 2660GV Setup This unit has been tested at the factory. 1. Remove all packaging and tape prior to operation. 2. Place the unit on a sturdy, level base. 3. The popper unit has 4 glide feet preinstalled at the factory (see image below). Install a Black Crutch Tip on each of the 4 glide feet. Firmly push the crutch tip over the glide until it covers the glide entirely. 4. Door knobs are shipped in the accessories pack located inside the machine. Install a door knob with tee bolt on each popper door; install the knob with screw on the old maid pan. 5. Carefully install the light bulb (do not over-tighten) into the lamp holder located in the cabinet interior. Ensure the unit is OFF and unplugged before installing or changing the bulb (reference the Electrical Requirements section). 6. Make sure kettle lead-in cord is securely plugged into unit, and twisted to lock into the kettle receptacle. Glide (pre-installed at the factory) Black Crutch Tip General image shown for reference only. Page 5 gmpopcorn.com Antique Deluxe 60 Special Poppers Model No. 2660GT, 2660GTSV, 2660GV Electrical Requirements The following power supply must be provided: 2660GT, 2660GTSV, 2660GV: 120 V~, 1220 W, 60 Hz DANGER Machine must be properly grounded to prevent electrical shock to personnel. Failure to do so could result in serious injury, or death. DO NOT immerse any part of this equipment in water. DO NOT use excessive water when cleaning. Keep cord and plug off the ground and away from moisture. Always unplug the equipment before cleaning or servicing. Make sure all machine switches are in the OFF position before plugging the equipment into the receptacle. 008_051514 A certified electrician must furnish sufficient power for proper machine operation and install any supplied receptacle. We recommend this equipment be on a dedicated and protected circuit. Failure to wire properly will void the warranty and may result in damage to the machine. It is Gold Medal Products Co.'s recommendation that this machine be plugged directly into a wall outlet. The use of extension cords is not recommended due to safety concerns, and may cause sacrificed and/or reduced performance. Make sure cord is located to prevent a trip hazard or unit upset. Before You Plug In Machine 1. Make sure all machine switches are in the OFF position before plugging the equipment into the receptacle. 2. Make sure the wall outlet can accept the grounded plugs (where applicable) on the power supply cord. 3. The wall outlet must have the proper polarity. If in doubt, have a competent electrician inspect the outlet and correct if necessary. 4. DO NOT use a grounded to un-grounded receptacle adapter (where applicable). 5. Install the unit in a level position. CAUTION If the supply cord is damaged, it must be replaced by Gold Medal Products Co., its service agent or similarly qualified persons in order to avoid a hazard. 039_080614 Page 6 gmpopcorn.com Antique Deluxe 60 Special Poppers Model No. 2660GT, 2660GTSV, 2660GV OPERATING INSTRUCTIONS Controls and Their Functions KETTLE HEAT SWITCH Two position, ON/OFF lighted rocker switch - supplies power to the heating elements in the popping kettle. The green switch light ON indicates there is power to the kettle heating element. KETTLE MOTOR SWITCH Two position, ON/OFF lighted rocker switch - supplies power to the kettle agitator motor. The Kettle Motor Switch MUST be ON at all times when there is popcorn (popped or unpopped) in the kettle. The green switch light ON indicates there is power to the agitator motor. LIGHTS/WARMER SWITCH Two position, ON/OFF lighted rocker switch - supplies power to the interior cabinet light and heat element for the corn pan. Kettle Heat Switch Lights/Warmer Switch Kettle Motor Switch Label used on units with the PowerOff Control feature. POWEROFF CONTROL (if equipped) The PowerOff Control feature will automatically turn the kettle heat off after 15 minutes of idle time (no popcorn popped). The PowerOff Control will prevent the heat element and thermostat from cycling OFF-ON if the Kettle Heat Switch is left on. This feature saves electrical power and extends the life of the kettle heating element and thermostat. · When the Kettle Heat Switch is turned ON, and the kettle thermostat switches OFF, the PowerOff Control's 15 minute timer starts; the 15 minute timer resets each time a batch of popcorn is popped. · The small green neon light in the Kettle Heat Switch will blink OFF-ON to indicate the kettle has been automatically turned OFF. · To restart the kettle heating, cycle the Kettle Heat Switch OFF-ON. Page 7 gmpopcorn.com Antique Deluxe 60 Special Poppers Model No. 2660GT, 2660GTSV, 2660GV Popping Corn This section describes instructions for popping Standard (salted popcorn). Amount of Popcorn and Oil The popper is equipped with a corn, salt, and oil measure. We recommend flavored and colored coconut oil. Popcorn popped in coconut oil stays fresh longer and does not leave black deposits in your kettle like other oils. Use only top quality, fresh popcorn from reputable suppliers. Ingredient amounts for popping Standard Popcorn: Kettle Size 6 oz. Popcorn Charge 6 oz. (177 ml) Oil Charge 2 oz. (59 ml) Flavacol (Salt) 1/2 Tblsp. (7.5cc) For best results use Mega-Pop® 6 oz. premeasured pouches (Item# 2836). Popping Standard (Salted) Popcorn 1. Turn the Lights/Warmer, Kettle Heat and Kettle Motor Switches ON. 2. To determine when the kettle is ready to pop corn (about 4 minutes), test pop three kernels of corn and one ounce (30 ml) of popping oil. When the kernels pop, the kettle is ready for use. 3. Lift the kettle lid and load the Mega-Pop® premeasured popcorn and oil pouch into kettle, or pour in the popcorn and Flavacol, then add oil in the premeasured amounts specified above. Close lid. 4. When the corn has finished popping, gently dump the popcorn. 5. On the final kettle of corn, turn the Kettle Heat Switch OFF just as the lids are forced open by the popping corn. This procedure saves electricity, since the kettle has plenty of heat, and helps eliminate smoke/odor from any oil residue that remains after popping has stopped. 6. When finished popping, make sure KETTLE HEAT and KETTLE MOTOR switches are turned OFF. NEVER LEAVE THE HEAT ON WHEN YOU ARE NOT POPPING CORN! If unit is equipped with the PowerOff Control feature, the unit will automatically shut kettle heat OFF after 15 minutes of idle time (no popcorn popped). To restart kettle heating, cycle the Heat Switch OFF-ON. Page 8 gmpopcorn.com Antique Deluxe 60 Special Poppers Model No. 2660GT, 2660GTSV, 2660GV Care and Cleaning DANGER Machine must be properly grounded to prevent electrical shock to personnel. DO NOT immerse in water. Always unplug the equipment before cleaning or servicing. 025_020314 WARNING To avoid serious burns, DO NOT touch the kettle while it is hot! 028_082715 Good sanitation practice demands that all food preparation equipment be cleaned regularly (only use non-toxic, food grade cleaners). A clean looking, well-kept machine is one of the best ways of advertising your product. Note: It is extremely important to follow all of the cleaning procedures, otherwise parts damage and equipment failure will result. The warranty does not cover parts that are damaged due to improper cleaning. Daily Kettle Cleaning Instructions CAUTION: A hot kettle will cause burns if you touch it with your hand. Allow kettle to cool at least 1 hour before attempting to clean. DO NOT use ice or water to cool down a hot kettle! Severe kettle damage will result! 1. When cool, wipe the outside of the kettle with a clean, soft cloth. DO NOT use oven cleaners or abrasive materials as they will damage the kettle. 2. Every night, mix Gold Medal's Heat'n Kleen solution (Item No. 2095), 2 tablespoons per gallon of water. It is not necessary to use the entire gallon at once; only use enough to fill the kettle 1/2 inch deep. 3. Turn the kettle heat ON. When the water starts to boil, turn the kettle heat OFF. 4. Allow to cool for at least 1 hour, then dump the solution into a bucket and wipe the inside of the kettle with a clean cloth. Make sure all of the solution goes into the bucket; do not spill any in the interior of the machine. For an extra dirty kettle, the process may be repeated; or, after turning the kettle heat OFF, allow solution to sit in the kettle overnight. The next morning, dump the solution into a bucket and wipe the inside of the kettle with a clean cloth. 5. With the unit OFF and unplugged, wipe the kettle lead cord with a clean SLIGHTLY damp cloth. DO NOT get moisture into the kettle lead-in cord, severe damage will result. Page 9 gmpopcorn.com Antique Deluxe 60 Special Poppers Model No. 2660GT, 2660GTSV, 2660GV Daily Unit Cleaning Instructions 1. With the machine OFF, unplug the unit and allow it to cool before attempting to clean. 2. Make sure to clean all pans/accessories in order to sanitize them before each use. 3. Take a clean, SLIGHTLY damp cloth and wipe excess grease from the glass and cabinet. 4. Wipe the stainless steel parts with a clean cloth and cleaner designed for stainless steel, such as Gold Medal Watchdog Stainless Cleaner (Item No. 2088). DO NOT use oven cleaners or abrasive materials as they will damage parts of the machine. 5. Clean the glass panels with glass cleaner. Gold Medal Watchdog Glass Cleaner (Item No. 2588) is recommended. Ammonia cleaners will damage the plastic doors. Use only non-ammonia cleaners, such as Gold Medal Watchdog Glass Cleaner (Item No. 2588). Page 10 gmpopcorn.com Antique Deluxe 60 Special Poppers Model No. 2660GT, 2660GTSV, 2660GV Troubleshooting Issue Power to the Unit Kettle Does Not Heat Long Popping Cycles (Longer than 4 minutes for Salt Popcorn) Kettle Agitator Shaft not Rotating Possible Cause A. Power to the Unit A. Power to the Kettle B. Kettle Heat Switch C. PowerOff Control D. Heating Element A. Low Voltage B. Inadequate Supply Lines C. Inferior Corn A. Kettle Motor Switch B. Kettle Agitator Shaft/Stir Blade not rotating. (Unit must be OFF, unplugged and cool prior to checking or adjusting the agitator assembly.) Solution A. Make sure the unit's power cord is plugged in. A. Make sure kettle lead-in cord is plugged in and twisted to lock into the kettle receptacle. B. Have a qualified service person check the voltage to and from the Kettle Heat Switch; if switch is defective, replace it. C. Units with the PowerOff Control feature, kettle heat will automatically shut OFF after 15 minutes of idle time (no popcorn popped). The small green neon light in the Kettle Heat Switch will blink OFF-ON to indicate the kettle has been automatically turned OFF. To restart kettle heating, cycle the Heat Switch OFF-ON. Reference the Controls and Their Functions section of this manual. D. Heating element in the kettle may be burned out. Check with a qualified service person for inspection/repair. A. If the machine is operated on low voltage, this could cause the kettle not to reach the proper operating temperature. Check with a qualified electrician. B. Inadequately sized electrical supply lines or use of extension cord, in addition to being a fire hazard, would also prevent the kettle from reaching the proper operating temperature. Check with a qualified electrician. C. Inferior quality corn would result in longer popping cycles. Use only top quality hybrid popcorn from reputable suppliers. Even then, if you let your corn pick up moisture or dry out, your popping cycles will be slow. A. If the kettle agitator shaft is not rotating, DO NOT pop corn. Make sure the Kettle Motor Switch is ON. If the switch is ON, and the shaft is not rotating, the switch or motor may be faulty, contact qualified service personnel for inspection/repair. B. If the kettle agitator shaft is not rotating, DO NOT pop corn. Check the clearance between the kettle bottom and the stir blade; it should be 1/32" (use a dime). To adjust, reference the Agitator Set Collar Adjustment section. Page 11 gmpopcorn.com Antique Deluxe 60 Special Poppers Model No. 2660GT, 2660GTSV, 2660GV Agitator Set Collar Adjustment The following instructions describe how to properly adjust set collars on an agitator assembly with a floating stir rod. Steps to Adjust Set Collars Step 1: Make sure machine is OFF and unplugged, then allow unit to cool completely before attempting to adjust the agitator height. Step 2: Loosen the set screw in each set collar to be adjusted. Step 3: With the kettle mounted in the popper, adjust the shaft so the Agitator's Spur Gear contacts half of the Drive Motor Spur Gear (reference Spur Gear Placement image at right). DO NOT set spur gears at full gear contact; it can cause binding as the kettle is dumped. Step 4: Once shaft is positioned correctly, re-tighten the set screw in the set collar above the crossbar to secure in place. Step 5: Adjust clearance between the bottom of the crossbar and the lower set collar to 1/32" (thickness of a dime); then re-tighten set screw to secure in place (see image below). Step 6: Adjust set collar for agitator weight to be between 3/16" to 1/4" above the agitator weight. Once adjusted, re-tighten set screw to secure in place. Agitator's Spur Gear Agitator's Spur Gear should set halfway up on Drive Motor Spur Gear. Drive Motor Spur Gear Set Collar w/Set screw Spur Gear Placement Set Collar above Crossbar Crossbar Adjust clearance to thickness of a dime. 3/16" to 1/4" max. Agitator shown for general image reference only (lids not shown for clarity). Lower Set Collar (below Crossbar) Set Collar (for Agitator Weight) Agitator Weight Stir Rod Page 12 gmpopcorn.com Antique Deluxe 60 Special Poppers Model No. 2660GT, 2660GTSV, 2660GV MAINTENANCE INSTRUCTIONS DANGER Machine must be properly grounded to prevent electrical shock to personnel. Failure to do so could result in serious injury, or death. DO NOT immerse any part of this equipment in water. DO NOT use excessive water when cleaning. Keep cord and plug off the ground and away from moisture. Always unplug the equipment before cleaning or servicing. Make sure all machine switches are in the OFF position before plugging the equipment into the receptacle. 008_051514 DANGER Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death. Any alterations to this equipment will void the warranty and may cause a dangerous condition. NEVER make alterations to this equipment. Read the Installation, Operating, and Maintenance Instructions thoroughly before installing, servicing, or operating this equipment. 014_051514 WARNING No user serviceable parts inside. Refer servicing to qualified service personnel. 011_051514 CAUTION THE FOLLOWING SECTIONS OF THIS MANUAL ARE INTENDED ONLY FOR QUALIFIED SERVICE PERSONNEL WHO ARE FAMILIAR WITH ELECTRICAL EQUIPMENT. THESE ARE NOT INTENDED FOR THE OPERATOR. 027_010914 Page 13 gmpopcorn.com Antique Deluxe 60 Special Poppers Model No. 2660GT, 2660GTSV, 2660GV ORDERING SPARE PARTS 1. Identify the needed part by checking it against the photos, illustrations, and/or parts list. 2. Use only approved replacement parts when servicing this unit. 3. When ordering, please include part number, part name, and quantity needed. 4. Please include your model number, serial number, and date of manufacture (located on the machine nameplate/data plate) with your order. 5. Address all parts orders to: Parts Department Gold Medal Products Co. 10700 Medallion Drive Cincinnati, Ohio 45241-4807 Or, place orders by phone or online: Phone: (800) 543-0862 (513) 769-7676 Fax: (800) 542-1496 (513) 769-8500 E-mail: info@gmpopcorn.com Web Page: gmpopcorn.com Page 14 gmpopcorn.com Antique Deluxe 60 Special Poppers Model No. 2660GT, 2660GTSV, 2660GV Replacing Broken Glass Broken glass panels can be easily replaced. Gold Medal Products Co. does not ship glass. It can be obtained from a local glass shop, always purchase tempered glass. GLASS DIMENSIONS (Height x Width x Thickness) Front Glass: 22 1/2" X 15 1/8" X 1/8" (1 Piece) Side Glass: 22 1/2" X 13" X 1/8" (2 Pieces) 1. With the machine OFF, unplug the unit and allow it to cool before attempting to replace any glass. 2. Carefully remove all loose pieces of broken glass. 3. Lift out the Corn Pan (see Figure A). 4. Locate the Glass Retainer Strips holding in the glass panel, remove the screws to unfasten the retainers (see Figure A). Carefully remove the rest of the broken glass. Remove all rigid glass channels from around the glass to be replaced, set channels aside for reuse. To remove the Glass Strip with the Cover: · Bend out the tabs at the bottom and top of Glass Strip (see Figure A). · Pinch in the edge of the Glass Strip Cover just enough to rotate the cover out of the Glass Strip, then remove (see Figure B). · Remove the Glass Strip. When reinstalling, ensure the wiring is on top of the Glass Strip (as seen in Figure C). 5. Apply decals (if desired) to the new glass panel. 6. Slide the rigid glass channels over the exposed sides and bottom of the new glass panel. 7. Fasten new glass panel in machine with the existing Glass Strips and screws using the steps above as reference. Glass Retainer Strip (remove screws to unfasten) Glass Strip Cover Glass Strip (bend tab out to remove cover) Rotate Cover out to remove. Wiring is on top of Glass Strip. Remove Glass Strip to remove glass panel. Corn Pan (lift off to remove) Figure A Figure B Page 15 Figure C gmpopcorn.com Antique Deluxe 60 Special Poppers Model No. 2660GT, 2660GTSV, 2660GV Kettle Assembly 56000 Complete Agitator Assembly 1 (Includes Lids) 9 560 00 S ho wn 1 10 2 3 4 10 11 17 8** 7 5 **Apply Loctite 246 to bottom of set screws before installing. Kettle Model 56000 shown 5 6 27 26 13 14 15* 16 *See Parts 17 List note. 18, 16 Element/Heater View 25 24 20 19 23 Complete Agitator Assembly 22 (Includes Lids) 21 Complete Kettle Bottom Assembly includes Kettle Shell and Kettle Lead Assembly Page 16 gmpopcorn.com Antique Deluxe 60 Special Poppers Model No. 2660GT, 2660GTSV, 2660GV Kettle Assembly 56000 Parts List Item Part Description Part Number 56000 1 8-32 TALL ACORN NUT 47702 2 8-32 X 1/2 PHIL PAN M/S 47141 3 KETTLE SHELL 49431 4 KETTLE LEAD ASSY 49328 5 DUMP HANDLE RH 49314 6 DUMP HANDLE KNOB 47110 7 SPACER (for Dump Handle) 49362 8 8-32 X 1" SET SCREW 77933 9 LID & AGITATOR ASSY (Complete Assembly) 59103 10 KETTLE CROSSBAR ASSEMBLY 59102 11 FRONT LID W/FORMED LIFTER 49017 12 REAR KETTLE LID 49016 13 AGITATOR BEARING HUB 43434 14 NEEDLE BEARING 47106 SPUR GEAR KIT (Includes 2 gears with set 15* screws. Always replace Agitator Spur Gear and 47059K Kettle Drive Motor Gear as a set.) 16 SET SCREW #10-32 X 3/16 41742 17 AGITATOR SHAFT 69710 18 SET COLLAR 5/16 ID 5/8 OD 46649 19 AGITATOR WEIGHT 69715 20 STIR ROD 69714 Kettle Bottom Assembly Element/Heater View KETTLE BOTTOM ASSEMBLY (Complete 21 Assembly - includes Kettle Shell, Kettle Lead 56000W Assembly and parts listed below) 22 KETTLE GASKET 49368 23 KETTLE/HEATER 56006 24 8-32 TOP LOCK NUT (where used, always replace lock nut if removed) 67943 25 450°F THERMOSTAT (includes two 6-32 X 3/16 Screws) 76089 26 THERMOSTAT SHUNT BAR 47193 Page 17 gmpopcorn.com Antique Deluxe 60 Special Poppers Model No. 2660GT, 2660GTSV, 2660GV Cabinet Exterior Front View 2, 3 1 See Kettle Assembly Section For Glass Panels, see Replacing Glass section. 4 7, 8 5, 6 9 Model 2660GT Shown Item Parts Description 1 UPPER FRAME ASSEMBLY 2 INSPECTION COVER (includes cover and corner ornaments, Part Nos. 47402R, 47402L) 3 SCREW #8 HEX WASHER HEAD (fastens inspection cover to upper frame assembly) 4 22 1/8" GLASS CHANNEL (used on side edges of front and side glass panels) 5 13 1/8" GLASS CHANNEL (used on bottom edge of side glass panels) 6 15 1/8" GLASS CHANNEL (used on bottom edge of front glass panel) 7 10-24 X ¾ HEX HEAD 8 GLIDE 9 BLACK CRUTCH TIP 2660GT 49375 49572 47771 49212 49213 49214 41314 47328 49123 Part Number 2660GTSV 49680 49685 47771 49212 49213 49214 41314 47328 49123 2660GV 49944 49942 47771 49212 49213 49214 41314 47328 49123 Page 18 gmpopcorn.com Antique Deluxe 60 Special Poppers Model No. 2660GT, 2660GTSV, 2660GV Cabinet Exterior Rear View **Complete Door Hardware Kit (See next page for individual component breakdown). 1 2, 3 4** 4** 5 For Labels, see Safety Label Section. 6 * CAUTION: If supply cord is damaged, it must be replaced by Gold Medal Products Co., its 7, 8 9 service agent, or similarly qualified persons in order to avoid a hazard. Item Part Description 1 MAGNETIC CATCH 2 MAGNETIC CATCH BRACKET 3 MAGNETIC BRACKET SHIM 4** COMPLETE DOOR HARDWARE KIT 5 PLEXIGLASS DOOR 6 DROP PANEL 7 KNOB LID LIFT 8 8-32" X 3/8" PH PAN W/SEMS 9 OLD MAID PAN 10* LEAD-IN CORD 15 AMP PLUG 11 #SR-6P3-4 STRAIN RELIEF 11 10* Model 2660GT shown Part Number All Models 47561 77089 38527 61380 49396 49210 47120 42227 49100 22038 76026 Page 19 gmpopcorn.com Antique Deluxe 60 Special Poppers Model No. 2660GT, 2660GTSV, 2660GV Door Hardware Kit 61380 Individual Component Breakdown 1 2 4 3 5 6 7 8 9 Complete Door Hardware Kit (P/N 61380) (contains all parts shown above) Item Part Description 1 KNOB LID LIFT 2 TEE BOLT 3 8-32 X 5/16 SLOTTED HEX 4 8-32 X 3/8 PH PAN W/SEMS 5 ACORN NUT #8-32 6 MALE HINGE SHORT LEFT 7 FEMALE HINGE LEFT HAND 8 FEMALE HINGE RIGHT HAND 9 MALE HINGE SHORT RIGHT Part Number 61380 47120 75267 49594 42227 47702 41349 61359 61373 41350 Page 20 gmpopcorn.com Antique Deluxe 60 Special Poppers Model No. 2660GT, 2660GTSV, 2660GV Cabinet Interior Hanger Assembly 1 For Labels, see Safety Label Section. 2 3 4 5 6 7 See Kettle Assembly section for Kettle parts breakdown. Model 2660GT shown Data Plate 8 13 11, 12 9*, 10 *See Parts List note. Item Part Description 1 SWITCH BOX 2 SWITCH BOX LABEL 3 GREEN LIGHTED ROCKER SWITCH 4 DPST ROCKER SWITCH 5 LIGHT SHIELD ANGLE 6 65 WATT REFLECTOR FLOOD 7 REAR HANGER ARM 8 FRONT HANGER ARM SPUR GEAR KIT (Includes 2 gears with set 9* screws. Always replace Agitator Spur Gear and Kettle Drive Motor Gear as a set.) 10 10-32" X 3/16" SET SCREW 11 GEAR BLOCK ASSEMBLY 12 10-24 X 1 HEX MACH SCREW (fastens the gear block assembly to the kettle drive motor.) 13 15 AMP TWIST LOCK KETTLE RECPT Part Number All Models 48501 48502 42798 42532 47799 41671 49009 49010 47059K 41742 67194 49322 49330 Page 21 gmpopcorn.com Antique Deluxe 60 Special Poppers Model No. 2660GT, 2660GTSV, 2660GV Cabinet Interior Bottom View 1, 2 3, 4 5, 4 1, 2 7 6 Model 2660GT shown 12 11 10 8, 9 See Safety Label Section. Item Part Description 1 GLASS RETAIN STRIP,REAR 2 8-32 X 1 UNSL NON-IND HWH (holds retainer) 3 GLASS RETAIN STRIP, FRONT 4 8-32 X 1 UNSL NON-IND HWH (holds retainer) 5 GLASS STRIP (beneath the glass strip cover) 6 GLASS STRIP COVER (covers wiring) 7 CORN PAN 8 HEX NUT #8-32 STAINLESS 9 8-32 x 3/8 SLOTTED HEX 10 WIRING GUARD 11 120 VOLT 50 WATT HEAT ELEMENT 12 STRIP HEATER BRACKET Part Number All Models 49215 39008 49216 12008 49318 49319 49211 89129 67899 49201 40031 49425 Page 22 gmpopcorn.com Antique Deluxe 60 Special Poppers Model No. 2660GT, 2660GTSV, 2660GV Dome Interior Electrical Components 1 2 266 0G T 9 8 General image shown for parts reference only. 3 4 7 See Safety Label Section. 5 6 PowerOff Control (Available on Model 2660GT only.) Item Parts Description 1 LIGHT SHIELD CONICAL 2 LAMP HOLDER 3 AUTO KETTLE POWEROFF CNTRL PCB 4 BRACKET, KETTLE POWEROFF CNTRL 5 6-32 X 3/8 PHIL PAN M/S 6 #6 INTERNAL TOOTH L/W 410SS 7 15 AMP TWIST LOCK KETTLE RECPT 8 120 VOLT KETTLE DRIVE MOTOR 9 .500 IN BUSHING, SNAP 2660GT 49480 47047 55402 55427 39000 39001 49330 47038 47236 Part Number 2660GTSV 49480 47047 49330 47038 47236 2660GV 49480 47047 49330 47038 47236 Page 23 gmpopcorn.com Antique Deluxe 60 Special Poppers Safety Labels Model No. 2660GT, 2660GTSV, 2660GV 1 2 4 3 Unit Labels 5 6 7 Label used on units with the PowerOff Control feature. 8 Kettle Lead In Label 9 10 Power Cord Labels Item Part Description 1 WARNING, MAX LAMP 75W 2 LABEL UNPLUG TO CLEAN 3 SERVICE LABEL 4 UNIVERSAL POPPER DECAL 5 MAIN GROUND LABEL 6 WARNING, SURFACE CONTACT 7 LABEL POWEROFF CNTRL 8 CONDUIT WARNING LABEL 9 WARNING LABEL CORD 10 POWER CORD TAG Part Number 2660GTSV, 2660GV 2660GT 41452 41452 76097 76097 87935 87935 41019 41019 42375 42375 87087 87087 N/A 55436 82840 82840 68720 68720 76135 76135 Page 24 gmpopcorn.com Antique Deluxe 60 Special Poppers Accessories Model No. 2660GT, 2660GTSV, 2660GV 1 2 3 Item Part Description 1 STAMPED ALUMINUM SCOOP 2 6.5 CC MEASURE 3 6 OZ MEASURE Part Number All Models 2071 47678 49049 Page 25 gmpopcorn.com Antique Deluxe 60 Special Poppers Model No. 2660GT, 2660GTSV, 2660GV Wiring Diagram Model No. 2660GTSV, 2660GV Page 26 gmpopcorn.com Antique Deluxe 60 Special Poppers Model No. 2660GT, 2660GTSV, 2660GV Model No. 2660GT Page 27 gmpopcorn.com Antique Deluxe 60 Special Poppers Model No. 2660GT, 2660GTSV, 2660GV WARRANTY WARRANTY Gold Medal Products Co. warrants to the original purchaser each item of its manufacture to be free of defects in workmanship and material under normal use and service. Gold Medal Products Co.'s obligation under this warranty is limited solely to repairing or replacing parts, f.o.b. Cincinnati, Ohio, which in its judgment are defective in workmanship or material and which are returned, freight prepaid, to its Cincinnati, Ohio factory or other designated point. Except for "Perishable Parts" on specific machines, the above warranty applies for a period of two (2) years from the date of original sale to the original purchaser of equipment when recommended operating instructions and maintenance procedures have been followed. These are packed with the machine. Parts warranty is two (2) years, labor is six (6) months. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. In no event shall Gold Medal Products Co. be liable for special, incidental or consequential damages. No claim under this warranty will be honored if the equipment covered has been misused, neglected, damaged in transit, or has been tampered with or changed in any way. No claim under this warranty shall be honored in the event that components in the unit at the time of the claim were not supplied or approved by Gold Medal Products Co. This warranty is effective only when electrical items have been properly attached to city utility lines only at proper voltages. This warranty is not transferable without the written consent of Gold Medal Products Co. The term "Original Purchaser" as used in this warranty shall be deemed to mean that person, firm, association, or corporation who was billed by the GOLD MEDAL PRODUCTS CO., or their authorized distributor for the equipment. THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS CO. AT 1-800-543-0862 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIPMENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS CONCERNING THE REPAIR OR REPLACEMENT OF PARTS. NOTE: This equipment is manufactured and sold for commercial use only. 10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA gmpopcorn.com Phone: (800) 543-0862 Fax: (800) 542-1496 (513) 769-7676 (513) 769-8500 © 2016 The text, descriptions, graphics, layout, and other material in this publication are the exclusive property of Gold Medal Products Co. and shall not be used, copied, reproduced, or published in any fashion, including website display, without its express written consent. Page 28 gmpopcorn.comGPL Ghostscript 8.64 PScript5.dll Version 5.2.2