Quick Installation Guide

1. Connect the Hardware

Follow these steps to connect your router:

• Antenna Installation: Install the two antennas and position them upwards.
• SIM Card Insertion: Insert the Micro SIM card into the designated slot until you hear a click.

  SIM Card Requirements: The router supports Micro SIM cards. A Nano SIM card with a provided adapter or a standard SIM card with a provided sticker may also be used.

• Power Connection: Connect the power adapter to the router and then to a power outlet. Turn on the router.

2. Verify the Hardware Connection

Check the status of the LEDs on the router:

• Power LED: Should be on, indicating the router has power.
• Internet LED: Should be on, indicating a successful connection to the internet. If the Internet LED is not on, refer to the "Need Help?" section, Q2.
• Wi-Fi LED: Should be on, indicating the Wi-Fi network is active.

For optimal internet connection, ensure 2 or 3 bars of the Signal Strength LED are lit. If the signal is weak, try moving the router to a location that receives a stronger mobile network signal, such as near a window.

3. Enjoy the Internet

Connect your devices to the internet:

Wired Connection:

Connect your computers to the router's LAN ports using Ethernet cables.

Wireless Connection:

1. Find Network Details: Locate the SSIDs (network names) and the wireless password printed on the label at the bottom of the router. Typically, these are labeled as "SSID: TP-Link XXXX" and "SSID: TP-Link XXXX 5G", along with a "Wireless Password/PIN: XXXXXXXXX".
2. Connect Your Device: On your computer or smart device, click the network icon or go to Wi-Fi settings. Select the appropriate SSID and enter the wireless password to join the network.

Customize the 4G LTE Router

Access the router's management page to configure settings:

1. Ensure your computer is connected to the router, either via wired Ethernet or wirelessly.
2. Launch a web browser and navigate to either http://tplinkmodem.net or http://192.168.1.1.
3. You will be prompted to create a new password for future logins to the management page.
4. Follow the on-screen instructions of the Quick Setup to complete the initial configuration.

Note: This router can also be configured in Wireless Router Mode for ADSL/Cable connections. For advanced configurations, consult the full user guide on the TP-Link official website at www.tp-link.com.

Tether App

The TP-Link Tether app offers a user-friendly way to manage your router:

• Block unauthorized users from connecting to your network.
• Change basic wireless network settings.
• View information about connected clients.
• Set up Parental Controls with access time restrictions.

How to Begin with Tether App:

1. Download the TP-Link Tether app from the Apple App Store or Google Play Store.
2. Ensure your smart device is connected wirelessly to your home network.
3. Launch the Tether app and start managing your home network.

[Scan to download the app]

Need Help?

Q1. What should I do if I cannot access the web management page?

• If your computer has a static IP address, configure it to obtain an IP address automatically.
• Ensure you have entered http://tplinkmodem.net or http://192.168.1.1 correctly in the web browser.
• Try using a different web browser.
• Reboot your router and try again.
• Disable and then re-enable your active network adapter.

Q2. What should I do if I cannot access the internet?

• Verify that your SIM card is an LTE or WCDMA card and is within your internet service provider's service area.
• Ensure your SIM card has sufficient credit.
• Check the LAN connection by accessing the web management page (http://tplinkmodem.net or http://192.168.1.1). If the page doesn't load, refer to Q1.
• Once logged into the web management page, check the following:
  1. Go to Advanced > Network > Internet to confirm your ISP parameters are correctly entered. If not, create a new profile with the correct parameters.
  2. Go to Advanced > Network > PIN Management to verify if a PIN is required and enter it if necessary.
  3. Go to Advanced > Network > Data Settings to check if the data allowance has been exceeded. Adjust or disable the data limit if needed.
  4. Go to Advanced > Network > Internet to ensure Mobile Data is enabled.
  5. If you are in a roaming service area, confirm with your ISP and enable Data Roaming in Advanced > Network > Internet.

Q3. How do I restore the router to its factory default settings?

• With the router powered on, press and hold the RESET button on the rear panel until the Power LED flashes, then release it. Wait for the router to reset.
• Alternatively, log in to the web management page, navigate to Advanced > System Tools > Backup & Restore, click "Factory Restore", and wait for the process to complete.

Q4. What should I do if I forget my web management page password?

Refer to Q3 to reset the router to factory defaults, then create a new password.

Q5. What should I do if I forget my wireless network password?

• The default wireless password is printed on the router's product label.
• Connect a computer directly to the router via Ethernet cable. Log in to the web management page and go to Basic > Wireless to view or reset your password.

Safety Information

• Keep the device away from water, fire, humidity, and hot environments.
• Do not attempt to disassemble, repair, or modify the device.
• Do not use a damaged charger or USB cable.
• Use only recommended chargers.
• Do not use the device where wireless devices are prohibited.
• The adapter should be installed near the equipment and be easily accessible.