Manuals+

YASHE HGM-410 Food Processor Instruction Manual

Model: HGM-410

Specifications: 220-240V~, 50-60Hz, 1300W

Key Functions: RENDER, DRY GRINDING, MINCE, KNEAD DOUGH, ORANGE JUICE, CUTTING/SHREDDING, EGG BEATING, GRINDING.

Important Safety Instructions

  • Read all instructions carefully before use and keep for future reference.
  • This appliance is for normal domestic use only.
  • Not for use by persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless supervised or guided by a responsible person.
  • Young children should be supervised to ensure they do not play with the appliance.
  • If the power cord is damaged, it must be replaced by the manufacturer, service agent, or qualified persons to avoid danger.
  • Appliance has a safety switch preventing operation unless accessories are securely installed.
  • Features overheat protection; automatically shuts off and resumes when cooled (approx. 15 mins).
  • Do not operate for more than one minute at a time.
  • Accessible surfaces may become hot during operation.
  • Do not immerse power cord, connector, or housing base in water or any liquid to protect against electric shock, fire, or injury.
  • Unplug when not in use and before cleaning.
  • Do not immerse the Housing Base in water or rinse under tap water.
  • Do not push food with fingers or other objects (e.g., knives); always use the included pusher.
  • Handle blades and inserts with extreme care, especially during assembly, disassembly, and cleaning, as blades are very sharp.
  • Do not let the power cord hang over the edge of a table or counter, or touch hot surfaces.
  • Do not place near gas outlets, electric burners, or heating ovens.
  • Wait for all components to stop before unplugging and removing the processing bowl.
  • Ensure specified capacities are not exceeded.
  • Always use a reliable grounded electrical supply.

Before First Use

  1. After unpacking and before first use, ensure mechanical parts and accessories are not damaged.
  2. Remove all plastic bags and clean parts that will contact food.
  3. Carefully read the instruction manual before operation.

Attention: Blades are very sharp, handle with care!

Parts

Part NumberPart Name
1Housing Base
2Speed Dial
3Safety Switch
4Processing Bowl
5Robot Spindle
6Silicone Ring
7Lid for Container
8Large Pusher
9Small Pusher
10Citrus Juicer Cone
11Citrus Juicer Attachment
12Shredding/Slicing Disc (Fine)
13Shredding/Slicing Disc (Coarse)
14French Fry Disc
15Double Chopping Blade
16Kneading Blade
17Spatula
18Grinding Mill Pot
19Grinding Mill Lid
20Measuring Cup
21Mixing Jar Lid
22Mixing Jar
23Mixing/Grinding Blade Lid
24Whisk Holder
25Double Whisk

Speed Dial: Pulse - OFF - 1 - 2 - 3

ATTENTION: The appliance features three safety interlocks: Housing Base, Processing Bowl, and Lid. Ensure the Processing Bowl, Lid, and Large Pusher are securely locked before starting.

If the machine does not operate, check assembly steps first.

How to Use

Chopping Blade

  1. Place the Processing Bowl onto the Housing Base. The angle between the handle and the main body's safety switch should be approximately 55 degrees. Ensure the main body is on a flat surface and stable.
  2. Hold the Processing Bowl handle and turn it clockwise onto the Housing Base. When the arrow on the bowl aligns with the base or a "click" sound is heard, the bowl is locked.
  3. Place the Robot Spindle into the Processing Bowl.
  4. Attach the Double Chopping Blade to the Robot Spindle.
  5. Add food ingredients (Max 500g) into the Processing Bowl.
  6. Place the Lid for Container with the Large Pusher onto the Processing Bowl. Turn the lid clockwise until it locks with a "click" sound.
  7. Plug in the machine and turn the speed dial to 3 to start. Operating time should be less than 30 seconds.

Remarks:

  • Ensure the chopping blade is placed first before adding food to avoid difficult assembly.
  • Lock the processing bowl, lid, and large pusher securely in place.
  • Do not chop hard foods like coffee beans or ice cubes, as this may crack the bowl or dull the blade.
  • Do not exceed the maximum fill line to avoid poor results or damage to the machine.
  • Unplug the machine if food gets blocked, then remove it.

Attention: The disc is very sharp, handle with care!

Kneading Blade

  1. Follow the first 3 steps for the chopping blade. Place the kneading blade on the robot spindle.
  2. Add flour (Max 600g) into the processing bowl.
  3. Place the Lid for Container with the Large Pusher onto the processing bowl. Turn the lid clockwise until it locks with a "click" sound.
  4. Plug in the machine, turn the speed dial to 2, and operate for 3 minutes. Gradually add water through the feeding tube until the dough forms rounded pieces.

Remarks: For best results, continue kneading until the dough starts to tap the inner side wall of the processing bowl.

Slicing/Shredding Discs (Fine/Coarse) & French Fry Disc

  1. Follow the first 3 steps for the chopping blade.
  2. Choose the appropriate disc (fine slicing/shredding, coarse slicing/shredding, or French fry disc) and attach it to the robot spindle.
  3. Place the Lid for Container onto the processing bowl. Turn the lid clockwise until it locks with a "click" sound.
  4. Plug in the machine and turn the speed dial to 3 to start. Operation time should be less than 30 seconds.
  5. Add food ingredients into the feeding tube; the size should not exceed the tube. Insert the large or small pusher. Ensure the large pusher is properly seated if used.

Remarks:

  • Ensure food size is suitable for the feeding tube before starting.
  • Always use the pusher for slicing or shredding. Never put fingers into the feeding tube during operation.
  • Unplug the machine if food gets blocked, then remove it.

ATTENTION: The disc is very sharp, handle with care!

Double Whisk

  1. Follow the first 3 steps for the chopping blade.
  2. Add eggs into the processing bowl (minimum 3 eggs). Mount the double whisk onto the robot spindle.
  3. Place the Lid for Container with the Large Pusher onto the processing bowl. Turn the lid clockwise until it locks with a "click" sound.
  4. Plug in the machine and turn the speed dial to 3 to start. Operation time should be less than 3 minutes.

Remarks:

  • Ensure the processing bowl is dry and clean, free from water and oil, when whisking egg whites.
  • The double whisk cannot be used for kneading dough.
  • Do not exceed the maximum fill line.

Citrus Juicer

  1. Follow the first 3 steps for the chopping blade.
  2. Insert the citrus juicer attachment onto the robot spindle and turn clockwise until it clicks.
  3. Mount the citrus juicer cone onto the citrus juicer attachment.
  4. Plug in the machine and turn the speed dial to 1 to start. Operation time should be less than 1 minute.
  5. Place halved oranges or other citrus fruits onto the cone and hold them steady.

Remarks: Always operate the citrus juicer at speed 1.

Mixing Jar

  1. Check if the silicone ring is installed in the mixing/grinding blade lid.
  2. Install the mixing/grinding blade lid into the bottom of the mixing jar. Turn clockwise. Ensure it is locked to prevent liquid leaks.
  3. Add food and water into the mixing jar.
  4. Turn clockwise to lock the mixing jar lid. Place the measuring cup onto the mixing jar lid.
  5. Place the assembled mixing jar with food onto the housing base. The angle between the handle and the main body's safety switch should be approximately 55 degrees. Ensure the main body is on a flat surface and stable.
  6. Hold the mixing jar handle and turn it clockwise onto the housing base.
  7. Plug in the machine and turn the speed dial to 3 to start. Operation time should be less than 1 minute.

Remark:

  • Do not add food with temperatures above 80°C, or exceeding the Max line.
  • Do not put fingers into the jar during operation.
  • Ensure the mixing jar lid is covered before mixing.
  • For best results, cut food into small pieces before mixing.
  • If results are poor after 1 minute, turn off the machine for 2 minutes, then resume for another minute.

Attention: The blade is very sharp, handle with care!

Grinding Mill Pot

  1. Add food ingredients into the grinding mill pot (e.g., dry soy, coffee beans, chilies are suitable. Ice cubes, turmeric, and maca are not suitable).
  2. Check if the silicone ring is installed in the mixing/grinding blade lid.
  3. Install the mixing/grinding blade into the bottom of the grinding mill pot. Turn clockwise. Ensure it is locked to prevent leaks.
  4. Place the assembled grinding mill pot with food onto the housing base. Ensure the main body is on a flat surface and stable.
  5. Turn clockwise to lock it onto the housing base.
  6. Plug in the machine and turn the speed dial to 3 to start. Operation time should be less than 30 seconds.

Remark:

  • Do not install the grinding mill pot without the mixing/grinding blade lid onto the housing base.
  • Do not add food beyond the MAX line.
  • If results are poor after 30 seconds, stop the machine for 1 minute, then resume for another 30 seconds.

Attention: The blade is very sharp, handle with care!

Cleaning and Maintenance

  1. Unplug the power cord. Remove the food pusher from the feeding tube. Then, remove the lid by turning counter-clockwise. Lift off the lid.
  2. Disassemble the processing bowl by holding the handle and turning counter-clockwise, then remove the chopping blade/kneading blade/discs/double whisk/citrus juicer. Alternatively, disassemble the mixing jar/grinding mill pot from the housing base by turning counter-clockwise. Remove the mixing jar lid and the mixing/grinding blade lid.
  3. Wash upper parts in water and dry them. To remove grease, use warm soapy water and gently rub with a sponge.

ATTENTION:

  • Blades are very sharp, handle with care!
  • Do not put the housing base into liquid for cleaning!

Troubleshooting

ProblemResponse
Appliance not turning on.Ensure all assembly indications (on bowl lid, bowl, mixer jar, and motor unit) are aligned.
Appliance suddenly stops working.The bowl lid may come off during heavy processing. Close the lid correctly. The appliance will resume operation. If processing is too heavy, turn the control dial to OFF, unplug the appliance, and let it cool down. Place appliance and turn it on again. Process smaller batches.
Motor runs but citrus juicer cone does not turn.Check if the knife holder and citrus juicer are inserted correctly. Check if the citrus juicer sieve is fixed correctly (indication on sieve points to bowl handle).
Can I clean removable parts in the dishwasher?Yes, except for the motor unit and blade unit protection cap.
What does "pulse" mean?When you press the Pulse button, the appliance operates at maximum speed as long as you press the button. Pulse is recommended for more control, e.g., during chopping.
Can I pour boiling hot ingredients into the mixer?No, let liquids or ingredients cool down to 80°C to avoid damaging accessories.
Why does the motor produce an unpleasant odor during processing?It is common for a new appliance to emit an unpleasant odor or smoke during first use. This will stop after a few uses. It may also happen if used for too long. In this case, turn off the appliance and let it cool for 60 minutes.
What to do if the blade unit or motor is blocked during processing?Turn off the appliance and use a spatula to dislodge ingredients blocking the blade unit. Process smaller quantities.
What if the mixer leaks?Turn off the appliance and pour out ingredients. Remove the blade unit interface. Check if the sealing washer is correctly assembled on the blade unit.
Why does the ice function not work?To use the ice function, first turn the control dial to ON. Then, press the ice button.

Recipes

PartFunctionsSpeedMax LoadKB TimeRest TimeEmpty Running Time
Chopping BladeChopping Meat, Cutting VegetablesMin 1 - Max 3500g30 seconds1 minute30 seconds
Kneading BladeKneading DoughMin 1500g flour, 250ml water1 minute3 minutes30 seconds
Discs (Slicing/Shredding/French Fry)Slicing/Shredding (e.g., carrots, cheese, cucumber), French FriesMid 2 - Max 3500g1 minute2 minutes30 seconds
Mixing JarMaking Jam, Whipped Milk, Soup, etc.Mid 2 - Max 3 (ICE/SMOOTHIE Mode)600g carrots, 900g water1 minute2 minutes10 seconds
Grinding Mill PotGrinding Spices, Coffee Beans, etc.Mid 2 - Max 380g30 seconds1 minute10 seconds
Citrus JuicerJuicing Citrus FruitsMin 11200ml1 minute2 minutes30 seconds
Double WhiskEgg Whites or Whole EggsMax 32-6 pieces3 minutes3 minutes30 seconds

Contact Information

EC REP: SUCCESS COURIER SL, CALLE RIO TORMES NUM.1, PLANTA1, DERECHA, OFICINA 3, Fuenlabrada, Madrid, 28947 Spain. Email: successservice2@hotmail.com

Manufacturer/Distributor: YASHE GLOBAL INC, 1226 NORTH KING ST., WILMINGTON DE 19801. Email: support@yashe-global.com. Website: www.yashe-global.com

Made In China

Symbols: UK CA, Recycling Symbol [recycle symbol], CE Mark, RoHS Compliant, WEEE Symbol [wheelie bin crossed out symbol]

Models: HGM-410 1300W Food Processor, HGM-410, 1300W Food Processor, Food Processor, Processor

PDF preview unavailable. Download the PDF instead.

C1LK7Z944PL Microsoft: Print To PDF

Related Documents

PreviewYASHE HGM-410 Food Processor Instruction Manual
Comprehensive instruction manual for the YASHE HGM-410 food processor, covering safety, operation, cleaning, troubleshooting, and recipes. Learn how to use various attachments like cutting blades, kneading blades, slicing discs, blending jar, grinding jar, citrus juicer, and double whisk.
PreviewYASHE HGM-410 11-in-1 Food Processor User Manual
User manual for the YASHE HGM-410 11-in-1 Food Processor, detailing its 1300W motor, 2.5L bowl, 1.5L blender, and multiple attachments for chopping, kneading, mixing, juicing, and grinding.
PreviewYASHE SL-5230D23C Food Slicer User Manual
Comprehensive user manual for the YASHE SL-5230D23C food slicer, covering installation, operation, safety, cleaning, and maintenance. Learn how to safely and effectively use your food slicer for various food items.
PreviewYASHE M21012 Food Dehydrator Instruction Manual
Comprehensive instruction manual for the YASHE M21012 Food Dehydrator, covering operation, safety precautions, accessory usage, cleaning, maintenance, troubleshooting, and product specifications.
PreviewYASHE FD-1019 Food Dehydrator Instruction Manual
Comprehensive instruction manual for the YASHE FD-1019 Food Dehydrator. Learn about product features, safe usage, assembly, operation, cleaning, maintenance, troubleshooting, and technical specifications.
Preview4L Multi-functional Mini Fridge Installation Manual
Installation guide for the Yashe 4L multi-functional mini fridge, covering pre-installation preparation, power connection (AC and DC), mode settings, and post-installation checks.