Dr. Brown's Deluxe Bottle Sterilizer

Instructions for Use

Package Contents: Deluxe Bottle Sterilizer, Measuring Cup, Tongs, Instruction Manual.

Specifications: Nominal voltage: 120 VAC/60 Hz 650W.

Important Safeguards

[Warning] Read the ENTIRE instruction manual before use to ensure proper safety precautions, operation, and maintenance. Failure to operate safely could result in damage or injury. This appliance is not for use by children; close supervision is required when used near children. Do not attempt disassembly. Use only Handi-Craft Company recommended attachments.

When using electrical appliances, always follow precautions to reduce the risk of fire, electrical shock, and injury:

• Ensure wall outlet voltage matches appliance voltage.
• Do not operate if damaged; return for service.
• If the supply cord or plug is damaged, it must be replaced by the manufacturer or qualified person.
• Place on a level, heat-resistant surface.
• Do not place on or near hot burners or in a heated oven.
• Do not let cord hang over edges or touch hot surfaces.
• DO NOT IMMERSE IN WATER.
• Household use only. Not for outdoor use.
• Unplug when not in use and before adding water.
• Do not spill liquid on cord or plug.
• Do not move appliance while in use or when it contains hot liquids.
• To operate, plug in and press power button. To disconnect, press power button then unplug.
• DO NOT open lid or reach over appliance while in use; steam causes burns.
• DO NOT touch hot surfaces during or immediately after use.
• After sterilizing, wait 10 minutes for parts to cool, then open top cover carefully, beware of residual steam.
• DO NOT EXCEED the recommended amount of water.
• If draining water, always POUR AWAY FROM YOU.
• Unplug and allow to cool for 60 minutes before cleaning/descaling.
• Be careful to avoid spilling or splashing water when removing contents.
• Heating element surface remains hot after use.
• Keep appliance and cord out of reach of children.
• Use only for intended purpose.
• Not intended for external timer or remote control.
• NOT FOR SPACE HEATING.
• This appliance has a polarized plug. Insert only one way into a polarized outlet. If it doesn't fit, reverse the plug. If still no fit, contact a qualified electrician. Do not modify the plug.
• A short power-supply cord is provided to reduce tripping hazards.
• Extension cords may be used with care. Ensure the extension cord's electrical rating is at least equal to the appliance's. Arrange longer cords to avoid tripping or snagging.

SAVE THESE INSTRUCTIONS

Parts

How to Use

1. Ensure all bottles, parts, and accessories are clean, rinsed, and empty before use.
2. Position the appliance on a flat, stable surface out of reach of children. Remove the tray.
3. Remove the measuring cup and tongs.
4. Fill the measuring cup to the FILL LINE (3 oz/80 mL) with DISTILLED WATER and pour onto the HEATING PLATE. For best performance, use recommended water and descale monthly. Mineral water may shorten appliance life. [Caution] DO NOT EXCEED the recommended amount of water. If draining water, POUR AWAY FROM YOU.
5. Place the removable tray (H) in the sterilizer heating chamber. Arrange bottles and parts in the tray. Refer to Figures A-G for suggested placement options for Dr. Brown's bottles and parts, showing arrangements for narrow and wide-neck bottles and their components.
6. Close the main cover (B) and arrange parts on the upper tray (C) as shown in Figures C and G. This appliance can sterilize items that withstand boiling water, such as pacifiers, teethers, toys, and utensils.
7. Close the top cover (A).
8. Plug in the power cord and press the ON Button (E). The cycle indicator lights (G) will illuminate RED-BLUE-GREEN initially, then the green light will remain lit, indicating "READY" mode.
9. Ready Cycle: With the green "ready" light on, press the Cycle Start Button (F).
10. Heat Cycle: The red light indicates the appliance is HEATING to create steam. It stays lit until water is consumed and the cycle is complete (approx. 8 minutes, may vary).
11. Cool Down Cycle: The blue light indicates the COOL DOWN cycle. If water was forgotten and the heat cycle started, the unit must complete the cool down cycle before another heat cycle can begin.
12. READY (unload) Cycle: When the cool down cycle is complete, the green "READY" light illuminates again. You may unload items or let them air dry.

[Warning] DO NOT open lid or reach over appliance while in use; steam causes burns and serious injuries. DO NOT touch hot surfaces, including top cover, main cover, and trays, during or immediately after use.

9. Open the main cover and remove all bottles. Place them on a flat surface. Open the top cover and re-assemble bottles with components.

[Caution] After sterilizing, wait 10 minutes for parts to cool, then open top cover carefully, beware of residual steam. Avoid spilling or splashing water on yourself when removing contents.

10. Turn off the unit by pressing the ON/OFF Button (E) or begin another sterilization cycle after adding 3 oz/80 mL of water.

Figure Descriptions:

• Figure A: Shows placement of vent tubes for narrow bottles.
• Figure B: Shows placement of narrow bottles.
• Figure C: Shows placement of narrow bottle parts (nipples/teats, collars, inserts) and pacifiers/soothers.
• Figure D: Shows placement of vent tubes for wide-neck bottles.
• Figure E: Shows placement of wide-neck bottles.
• Figure F: Shows placement of wide-neck bottle caps (2 on bottom, 4 on top).
• Figure G: Shows placement of wide-neck bottle parts (nipples/teats, collars, inserts) and pacifiers/soothers.
• *Note for Figure F/G: When sterilizing six (6) 9 oz/270 ml Wide-Neck Options™ bottles, remove the detachable handle from the inner tray to make room for all six bottles, reservoirs, and caps. Green reservoirs should be placed inside the bottles during sterilization. Ensure all parts are completely cool before removing.

Cleaning the Appliance

[Caution] Unplug and allow to cool for 60 minutes before cleaning and descaling. DO NOT IMMERSE IN WATER.

Clean the sterilizer at least once a week with regular use.

• Removable tray, tongs, and measuring cup: clean in hot soapy water and rinse thoroughly.
• Base exterior, heating chamber, and two covers: clean with a damp sponge or cloth.

Cleaning the Heating Plate

Mineral deposits may form on the metal heating plate. Descale every 4 weeks for proper function.

• Unplug the device.
• Remove the tray.
• Descale using a 3.5 oz/100 mL mixture of vinegar/water:
  1. Fill measuring cup to FILL LINE (3 oz/80 mL) with white vinegar.
  2. Add cold water up to the dashed line (.5 oz/20 mL) for a total of 3.5 oz/100 mL.
  3. Pour directly over the heating element.
  4. Turn the unit on and run a sterilization cycle.
  5. Empty remaining solution and rinse with clean water.

NOTE: DO NOT USE BLEACH, HARSH ABRASIVES, OR SOLVENTS on the heating chamber or elements, as this may cause permanent damage and void the warranty.

Warranty

Appliance is warranted against defects in material or workmanship for one year from the date of purchase. Defective parts will be repaired or replaced free of charge if not tampered with and used according to instructions. This warranty provides specific legal rights that vary by state.

Warranty does not cover defects caused by negligence, accidents, or improper use. To maintain good condition and warranty, USE ONLY AS DIRECTED.

Customer Service

For unsatisfactory operation or questions/comments, call Handi-Craft's Customer Service at 1-800-778-9001 or email info@handi-craft.com.

For purchases outside the United States and Canada, contact your local distributor.

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) it may not cause harmful interference, and (2) it must accept any interference received, including interference that may cause undesired operation.

Importer: Handi-Craft Company, 4433 Fyler Ave., St. Louis, MO 63116, Phone: 800-778-9001

Note: This equipment has been tested and found to comply with Class B digital device limits per FCC Rules. These limits provide reasonable protection against harmful interference in residential installations. The equipment generates, uses, and can radiate radio frequency energy and may cause interference if not installed and used per instructions. No guarantee of no interference in a particular installation.

If interference occurs, try correcting it by:

• Reorienting or relocating the receiving antenna.
• Increasing separation between equipment and receiver.
• Connecting equipment to a different circuit than the receiver.
• Consulting a dealer or experienced radio/TV technician.

[Warning] Changes or modifications not expressly approved by the responsible party for compliance could void the user's authority to operate the equipment.