Intellinet Industrial 10-Port Gigabit PoE+ Switch

Features

• Provides power and data connections for up to four PoE network devices
• IP30 slim-type metal housing to withstand harsh industrial conditions
• Wide operating temperature: -20 – 65°C (4 – 149°F)
• Option for DIN-rail installation
• Two small form-factor pluggable GBIC module slots (SFP)
• Two redundant DC inputs (48 - 55 V) with I/O terminal block

With a backplane speed of 20 Gbps, plenty of performance is available for your computers, servers and other networking devices. Each of the ports automatically senses the link speed of the connected network device and adjusts to 10, 100 or 1000 Mbps for compatibility and maximum performance. This PoE switch is designed to provide compatible devices with enough power when needed. It offers up to 30 watts of power per port until its power budget of 240 watts is reached.

For specifications, visit intellinet-network.com. Register your product at register.intellinet-network.com/r/509565.

Placement

Desktop Installation

Prior to use, place/position the switch:

• On a level surface that can support the weight of the switch and that offers at least 25 mm (approx. 1") of clearance for ventilation;
• Away from sources of electrical noise: radios, transmitters, broadband amplifiers, etc.;
• Within 100 m (approx. 328') of network devices it's to be connected to.

DIN-Rail Installation

[Step 1] With DIN-rail bracket attached to device with screws, angle bracket onto DIN rail.

[Step 2] Push device in till it clicks into place.

Diagram Description: Two images illustrating DIN-rail installation. The first shows a bracket being attached to the device. The second shows the device being mounted onto a DIN rail.

Power

Chassis Ground Column

Located on the side of the power supply connector, a grounding terminal connector is used to provide proper grounding for your Intellinet Network Solutions switch. It should be wired to an object that provides earth ground.

Terminal Block Installation

NOTE: Ensure all power is off/disconnected before beginning!

1. Loosen appropriate screws.
2. Insert bare power-supply wires into appropriate terminals (positive wire into positive terminal; negative wire into negative terminal).
3. Tighten appropriate screws to secure wires. (If desired, repeat steps 1 – 3 on second input pair.)
4. Install block into the device and tighten screws.

Diagram Description: Image of the power terminal block with V1+, V1-, V2+, V2- terminals labeled, and PWR2, P-FAIL, PWR1 indicators.

Front Panel

Diagram Description: An image of the Intellinet Industrial 10-Port Gigabit PoE+ Switch front panel, showing 8 Gigabit Ethernet ports, 2 SFP uplink ports, and various status LEDs including P-Fail, PoE Max, LINK/ACT, and PoE 1-8.

LED Status Indicators

Cat5e/6/6a/8.x UTP/STP cables provide optimal performance; if a status LED doesn't indicate a link or activity, check the corresponding device for proper setup and operation.

Disposal

Symbol Description: A symbol indicating that the product should not be treated as unsorted household waste.

This symbol on the product or its packaging means that this product must not be treated as unsorted household waste. In accordance with EU Directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE), this electrical product must be disposed of in accordance with the user's local regulations for electrical or electronic waste. Please dispose of this product by returning it to your local point of sale or recycling pickup point in your municipality.

Warranty Information

For warranty information, visit intellinet-network.com.

In MEXICO: Policy of Intellinet Warranty. Data of the importer and responsible party to the consumer: Intracom Mexico, S.A.P.I. de C.V. • Av. Interceptor Poniente # 73, Col. Parque Industrial La Joya, Cuautitlán Izcalli, Estado de México, C.P. 54730, México. • Tel. (55)1500-4500 • This warranty covers the following products against any manufacturing defect in their materials and workmanship.

A. Intellinet guarantees cleaning products, compressed air, and consumables for 60 days from the delivery date, or for the time until their content is fully depleted by their own function of use, whichever comes first.

B. Intellinet guarantees products with moving parts for 3 years.

C. Intellinet guarantees other products for 5 years (products without moving parts), under the following conditions:

1. All products covered by this warranty are subject to physical exchange, at no cost to the consumer.
2. The reseller does not have service workshops, as the products covered by this warranty do not have repairs or spare parts, as their warranty is for physical exchange.

The warranty exclusively covers those parts, equipment, or sub-assemblies that were factory-installed and does not include any additional equipment or any that have been added by the user or distributor. To make this warranty effective, present the product to the distributor at the place of purchase or at the domicile of IC Intracom Mexico, S.A.P.I. de C.V., along with the accessories contained in its packaging, accompanied by your duly completed and sealed policy by the selling house (seal and purchase date indispensable) where you acquired it, or the original invoice or ticket clearly stating the model, serial number (if applicable), and date of acquisition. This warranty is not valid in the following cases: If the product has been used under conditions other than normal; if the product has not been operated according to the instructions for use; or if the product has been altered or attempted to be repaired by the consumer or third parties.

Regulatory Statements

FCC Class B

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of Federal Communications Commission (FCC) Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: reorient or relocate the receiving antenna; increase the separation between the equipment and the receiver; connect the equipment to an outlet on a circuit different from the receiver; or consult the dealer or an experienced radio/TV technician for help.

CE Compliance

This device complies with the requirements of CE 2014/30/EU and / or 2014/35/EU. The Declaration of Conformity is available at: support.intellinet-network.com/barcode/509565

Logos Description: Includes FCC, CE, RoHS, UKCA, and PAP logos.

Contact Information

North America: IC Intracom America, 550 Commerce Blvd., Oldsmar, FL 34677, USA

Asia & Africa: IC Intracom Asia, 4-F, No. 77, Sec. 1, Xintai 5th Rd., Xizhi Dist., New Taipei City 221, Taiwan

Europe: IC Intracom Europe, Löhbacher Str. 7, D-58553 Halver, Germany

All trademarks and trade names are the property of their respective owners.