Instruction Manual for BOSCH models including: PDO Multi, Metal Detector PLL 5 Laser
Robert Bosch GmbH Power Tools Division 70745 Leinfelden-Echterdingen Germany www.bosch-pt.com 1 609 929 X41 (2010.10) T / 140 WEU WEU WEU PDO Multi PDO Multi de Originalbetriebsanleitung en Original instructions fr Notice originale es Manual original pt Manual original it Istruzioni originali nl Oorspronkelijke gebruiksaanwijzing
Robert Bosch GmbH Power Tools Division 70745 Leinfelden-Echterdingen Germany www.bosch-pt.com 1 609 929 X41 (2010.10) T / 140 WEU WEU WEU PDO Multi PDO Multi de Originalbetriebsanleitung
File Info : application/pdf, 16 Pages, 791.77KB
DocumentDocumentOBJ_BUCH-139-002.book Page 1 Thursday, October 28, 2010 10:46 AM WEU WEU Robert Bosch GmbH Power Tools Division 70745 Leinfelden-Echterdingen Germany www.bosch-pt.com 1 609 929 X41 (2010.10) T / 140 WEU PPDDOO MMuullttii PDO Multi de Originalbetriebsanleitung en Original instructions fr Notice originale es Manual original pt Manual original it Istruzioni originali nl Oorspronkelijke gebruiksaanwijzing da Original brugsanvisning sv Bruksanvisning i original no Original driftsinstruks fi Alkuperäiset ohjeet el tr Orijinal iletme talimat ar OBJ_BUCH-139-002.book Page 3 Thursday, October 28, 2010 9:38 AM | 3 a bc d k j e i h f g 1 2 3 4 5 6 7 PDO Multi Bosch Power Tools 1 609 929 X41 | (28.10.10) OBJ_BUCH-139-002.book Page 4 Thursday, October 28, 2010 9:38 AM 4 | 8 9 SSEENNSSOORR 10 8 99VV OPEN 11 12 1 609 929 X41 | (28.10.10) Bosch Power Tools OBJ_BUCH-139-002.book Page 16 Thursday, October 28, 2010 9:38 AM 16 | English eSn afety Notes Read and observe all instructions. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. f Have the measuring tool repaired only through qualified specialists using original spare parts. This ensures that the safety of the measuring tool is maintained. f Do not operate the measuring tool in explosive environments, such as in the presence of flammable liquids, gases or dusts. Sparks can be created in the measuring tool which may ignite the dust or fumes. f For technological reasons, the measuring tool cannot ensure 100 % certainty. To rule out hazards, safeguard yourself each time before drilling, sawing or routing in walls, ceilings or floors by means of other information sources, such as building plans, pictures from the construction phase, etc. Environmental influences, such as humidity or closeness to electrical devices, can influence the accuracy of the measuring tool. Surface quality and condition of the walls (e.g., moisture, metallic building materials, conductive wallpaper, insulation materials, tiles) as well as the amount, type, size and position of the objects can lead to faulty measuring results. Functional Description Intended Use The measuring tool is intended for the detection of metals (ferrous and non-ferrous metals, e.g., rebar), joists and "live" wires/conductors in walls, ceilings and floors. 1 609 929 X41 | (28.10.10) Bosch Power Tools OBJ_BUCH-139-002.book Page 17 Thursday, October 28, 2010 9:38 AM English | 17 Product Features The numbering of the product features shown refers to the illustration of the measuring tool on the graphic page. 1 Illuminated ring 2 Marking hole 3 Display 4 "ZOOM" button 5 Wood-detection button 6 Metal-detection button 7 "on/off" button 8 Felt pads 9 Sensor area 10 Battery lid 11 Pencil for marking (removable) 12 Latch of battery lid Display Elements a "Live" wire indicator b Wood detection indicator c Metal detection indicator d "ZOOM" function indicator e "ZOOM" measuring indicator f Measuring indicator g "AutoCal" calibration indicator h Indicator for magnetic metals i Indicator for non-magnetic metals j Switched-off audio signal indicator k Battery low indicator The accessories illustrated or described are not included as standard delivery. Bosch Power Tools 1 609 929 X41 | (28.10.10) OBJ_BUCH-139-002.book Page 18 Thursday, October 28, 2010 9:38 AM 18 | English Technical Data Digital Detector PDO Multi Article number 3 603 K10 000 Maximum scanning depth*: Ferrous metals Non-ferrous metals (copper) Copper conductors (live)** Wood 80 mm 60 mm 40 mm 20 mm Automatic switch-off after approx. 5 min Operating temperature 10 °C ... +50 °C Storage temperature 20 °C ... +70 °C Battery 1 x 9 V 6LR61 Battery 1 x 9 V 6F22 Operating lifetime (alkali-manganese batteries) approx. 6h Weight according to EPTA-Procedure 01/2003 0.25 kg * depends on material and size of objects as well as material and condition of structure ** less scanning depth for wires/conductors that are not "live" f In terms of accuracy, the measuring result can be inferior in case of unfavourable surface quality of the base material. Please observe the article number on the type plate of your measuring tool. The trade names of the individual measuring tools may vary. Assembly Inserting/Replacing the Battery Using alkali-manganese or rechargeable batteries is recommended for operation of the measuring tool. To open the battery lid 10, press the latch 12 in the direction of the arrow and fold up the battery lid. Insert the supplied battery. Pay attention that the polarity is correct, according to the representation on the inside of the battery lid. When the battery low indicator k lights up on the display, measuring is still possible for approx. 1 hour when using alkalimanganese batteries (lower battery service life for rechargeable batteries). When the battery low indicator k flashes, measuring is possible for approx. 10 minutes. When the battery low indicator k and the illuminated ring 1 (red) flash, measuring is no longer possible and the battery/rechargeable battery must be replaced. 1 609 929 X41 | (28.10.10) Bosch Power Tools OBJ_BUCH-139-002.book Page 19 Thursday, October 28, 2010 9:38 AM English | 19 f Remove the battery/rechargeable battery from the measuring tool when not using it for longer periods. When storing for longer periods, the batteries/rechargeable batteries can corrode or discharge themselves. Operation Initial Operation f Protect the measuring tool against moisture and direct sun light. Switching On and Off f Before switching the measuring tool on, make sure that the sensor area 9 is not moist. If required, dry the measuring tool using a soft cloth. f Do not subject the measuring tool to extreme temperatures or variations in temperature. As an example, do not leave it in vehicles for longer periods. In case of large variations in temperature, allow the measuring tool to adjust to the ambient temperature before putting it into operation. f Avoid heavy impact to or falling down of the measuring tool. To switch on switch on the measuring tool on, press any button. When switching the measuring tool on with the wood-detection button 5 or with the metal-detection button 6, it will automatically be in the respective detection function. When switching the measuring tool on with the "on/off" button 7 or with the "ZOOM" button 4, it will be in the detection function last used. After a brief self-check, the measuring tool is ready for operation. When the measuring tool is in the metal-detection function, the service readiness is indicated through a check mark behind the "AutoCal" calibration indicator g. To switch the measuring tool off, press the On/Off button 7. If none of the measuring tool buttons are pressed for approx. 5 minutes, the measuring tool switches off automatically in order to extend the service life of the battery. f Before drilling, sawing or routing into a wall, protect your- self against hazards by using other information sources. As the measuring results can be influenced through ambient conditions or the wall material, there may be a hazard even though the indicator does not indicate an object in the sensor range (no audio signal or beep and and the illuminated ring 1 lit green). Bosch Power Tools 1 609 929 X41 | (28.10.10) OBJ_BUCH-139-002.book Page 20 Thursday, October 28, 2010 9:38 AM 20 | English Operating Modes The measuring tool detects objects below the sensor area 9. Detecting Metal Objects When scanning for metal objects, press the metal-detection button 6. The metal detection indicator symbol c is indicated in the display and the illuminated ring 1 lights up green. Position the measuring tool onto the surface to be scanned and move it sidewards. When the measuring tool comes close to a metal object, then the amplitude of the measuring indicator f increases; when it moves away from the object, the amplitude decreases. At the position of maximum amplitude, the metal object is located below the centre of the sensor (below the marking opening 2). As long as the measuring tool is above the metal object, the illuminated ring 1 lights up red and a steady tone sounds. To localise the object precisely, press the "ZOOM" button 4 and keep it pressed while repeatedly (3x) moving the measuring tool over the object. The "Zoom" function indicator d appears in the display. The "Zoom" measuring indicator e has the greatest amplitude over the centre of the metal object. When very small or deeply embedded metal objects are being detected and the measuring indicator f does not react, press the "ZOOM" button 4 and keep it pressed while continuing to move the measuring tool over the area. Observe only the zoom measuring indicator e for the scan. If there are any metal inclusions in the material being scanned, then a continuous signal is indicated in the measuring indicator f. In this case, press the "ZOOM" button 4 and keep it pressed while continuing to move the measuring tool over the area. Observe only the "Zoom" measuring indicator e for the scan. If the metal object found is a magnetic (e.g. iron), then the indicator for magnetic metals h is displayed. For non-magnetic metals, the indicator for non-magnetic metals i is displayed. In order for the measuring tool to differentiate between the metal types, it must be positioned above the detected metal object (the illuminated ring 1 lights up red). For weak signals, the indication of the metal type is not possible. For steel wire mesh and reinforcements in the scanned structural material, an amplitude of the measuring indicator f is displayed over the complete surface. In this case, always use the "Zoom" function for the scan. For steel wire mesh, it is typical that the indicator for magnetic metals h is displayed directly above the rebar; the indicator for non-magnetic metals i is displayed between the rebars. 1 609 929 X41 | (28.10.10) Bosch Power Tools OBJ_BUCH-139-002.book Page 21 Thursday, October 28, 2010 9:38 AM English | 21 Detecting Wooden Objects When scanning for wooden objects, press the wood-detection button 5. The wood detection indicator symbol b and the "Zoom" function indicator d are indicated in the display and the arrow below the "Zoom" function indicator d flashes. The "AutoCal" calibration indicator g and the illuminated ring 1 go out. Position the measuring tool onto the surface being scanned. Then press the "ZOOM" button 4 and keep it pressed. Now the illuminated ring 1 lights up green, the "AutoCal" calibration indicator g is displayed again, the "Zoom" function indicator d as well as the arrow below it go out. With the "ZOOM" button 4 pressed, move the measuring tool uniformly above the structure without lifting it off or changing the applied pressure. During the scan, the felt pads 8 must always have contact with the structure. When a wooden object is detected, an amplitude is displayed in the measuring indicator f. Move the measuring tool over the surface repeatedly to localise the wooden object more precisely. After moving over the same area several times, the wooden object can be indicated quite accurately: The illuminated ring 1 lights up red and a steady tone sounds as long as the measuring tool is over the wooden object. The measuring indicator f has the greatest amplitude over the centre of the wooden object. The "Zoom" measuring indicator e is inactive when scanning for wooden objects. Caution: When having placed the measuring tool onto the surface to be scanned under which a wooden object is coincidentally located, and having moved it over the surface, the measuring indicator f, the arrow below the "Zoom" function indicator d and the illuminated ring 1 flash red. In this case, start the scan again by repositioning the measuring tool somewhat offset onto the structure and pressing the "ZOOM" button 4 again. When scanning for wooden objects, metal objects are sometimes also indicated as objects found at depths between 2050 mm. To distinguish between wooden and metal objects, switch to the detecting-metal function (see "Detecting Metal Objects"). When an object is indicated at the same location in this function, then it is clearly a metal object and not a wooden object. To continue searching for wooden objects, switch back to the detecting-wood function. Bosch Power Tools 1 609 929 X41 | (28.10.10) OBJ_BUCH-139-002.book Page 22 Thursday, October 28, 2010 9:38 AM 22 | English Scanning for "Live" Wires The measuring tool indicates lines that carry a voltage between 110 V and 400 V with frequencies corresponding to the widespread standard (AC with 50 or 60 Hz). Other lines (DC, higher/ lower frequency or voltage) are indicated only as metal objects. "Live" wires/conductors are indicated both during a metal scan as well as during a wood scan. When a "live" wire/conductor is detected, the indicator a appears in the display. Move the measuring tool over the surface repeatedly in order to localise the "live" wire/conductor more precisely. After moving the measuring tool over the surface several times, the "live" wire/conductor can be indicated quite precisely. If the measuring tool is very close to the wire/conductor (four or five bars in indicator a), the illuminated ring 1 flashes red and the signal tone sounds with a rapid tone sequence. "Live" wires/conductors can be detected easier when power consumers (e.g., lamps, appliances) are connected to the wire/ conductor being sought and switched on. Wires/conductors with 110 V, 230 V and 400 V (three-phase current) are detected with about the same scan capacity. Under certain conditions (such as when behind metal surfaces or behind surfaces with high water content), "live" wires/conductors cannot be detected with certainty. These ranges can be recognised in the metal detection function. When a measuring value is indicated all over a larger range of the measuring indicator f, then the material is screening off electrically and the scan for "live" wires/conductors is not reliable. Wires that are not "live" can be found as metal objects with the detecting-metal function. However, stranded cables are not indicated (contrary to solid copper conductors). Working Advice f Measuring values can be impaired through certain ambient conditions. These include, e.g., the proximity of other equipment that produce strong magnetic or electromagnetic fields, moisture, metallic building materials, foil-laminated insulation materials or conductive wallpaper or tiles. Therefore, please also observe other information sources (e.g. construction plans) before drilling, sawing or routing into walls, ceilings or floors. Switching Off the Signal Tone The signal tone can be switched on and off. For this, press the metal-detection button 6 and the wood-detection button 5 at the same time. When the signal tone is switched off, the switched-off audio signal indicator j appears on the display. The signal tone setting is maintained after switching the measuring tool off and on again. 1 609 929 X41 | (28.10.10) Bosch Power Tools OBJ_BUCH-139-002.book Page 23 Thursday, October 28, 2010 9:38 AM English | 23 Marking Objects Detected objects can be marked as required. For this, remove the pencil 11 from the measuring tool and carry out the scan as usual. Once you have found the limits or the centre of an object, simply mark the sought after location through the marking opening 2. "AutoCal" Calibration Indicator When the check mark behind the "AutoCal" calibration indicator g flashes over a longer period or if it is not displayed anymore, reliable scanning is no longer possible. In this case, send in the measuring tool to an authorised Bosch after-sales service agent. Exception: In the detecting wooden objects' function, the "AutoCal" calibration indicator g goes out as long as the "ZOOM" button 4 is not pressed. Maintenance and Service Maintenance and Cleaning When the measuring indicator f continuously shows an amplitude even though there is no metal object in the vicinity of the measuring tool, the measuring tool can be calibrated manually. For this, remove all objects in the vicinity of the measuring tool (including wrist watches or rings of metal) and hold the measuring tool up in the air. With the measuring tool switched off, press both the "on/off" button 7 and the wood-detection button 5 until the illuminated ring 1 lights up red and green at the same time. Then release both buttons. When the calibration process was successful, the measuring tool will start over after a few seconds and is then ready for operation. Wipe away debris or contamination with a dry, soft cloth. Do not use cleaning agents or solvents. In order not to affect the measuring function, decals/stickers or name plates, especially metal ones, may not be attached in the sensor area 9 on the front or back side of the measuring tool. Do not remove the felt pads 8 on the back side of the measuring tool. Replace the felt pads when they are damaged or used. For this, completely remove the felt pads and glue the new felt pads onto the same spots. Store and transport the measuring tool only in the supplied protective pouch. If the measuring tool should fail despite the care taken in manufacturing and testing procedures, repair should be carried out by an authorised after-sales service centre for Bosch power tools. Do not open the measuring tool yourself. In all correspondence and spare parts orders, please always include the 10-digit article number given on the type plate of the measuring tool. Bosch Power Tools 1 609 929 X41 | (28.10.10) OBJ_BUCH-139-002.book Page 24 Thursday, October 28, 2010 9:38 AM 24 | English Spare Parts Protective Pouch . . . . . . . . . . . . . . . . . . . . . . . . 1 609 203 P19 Battery lid 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 609 203 R32 Felt pads 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 609 203 P21 After-sales Service and Customer Assistance Our after-sales service responds to your questions concerning maintenance and repair of your product as well as spare parts. Exploded views and information on spare parts can also be found under: www.bosch-pt.com Our customer service representatives can answer your questions concerning possible applications and adjustment of products and accessories. Great Britain Robert Bosch Ltd. (B.S.C.) P.O. Box 98 Broadwater Park North Orbital Road Denham Uxbridge UB 9 5HJ Tel. Service: +44 (0844) 736 0109 Fax: +44 (0844) 736 0146 E-Mail: boschservicecentre@bosch.com Ireland Origo Ltd. Unit 23 Magna Drive Magna Business Park City West Dublin 24 Tel. Service: +353 (01) 4 66 67 00 Fax: +353 (01) 4 66 68 88 1 609 929 X41 | (28.10.10) Bosch Power Tools OBJ_BUCH-139-002.book Page 25 Thursday, October 28, 2010 9:38 AM English | 25 Australia, New Zealand and Pacific Islands Robert Bosch Australia Pty. Ltd. Power Tools Locked Bag 66 Clayton South VIC 3169 Customer Contact Center Inside Australia: Phone: +61 (01300) 307 044 Fax: +61 (01300) 307 045 Inside New Zealand: Phone: +64 (0800) 543 353 Fax: +64 (0800) 428 570 Outside AU and NZ: Phone: +61 (03) 9541 5555 www.bosch.com.au Republic of South Africa Customer service Hotline: +27 (011) 6 51 96 00 Gauteng BSC Service Centre 35 Roper Street, New Centre Johannesburg Tel.: +27 (011) 4 93 93 75 Fax: +27 (011) 4 93 01 26 E-Mail: bsctools@icon.co.za KZN BSC Service Centre Unit E, Almar Centre 143 Crompton Street Pinetown Tel.: +27 (031) 7 01 21 20 Fax: +27 (031) 7 01 24 46 E-Mail: bsc.dur@za.bosch.com Western Cape BSC Service Centre Democracy Way, Prosperity Park Milnerton Tel.: +27 (021) 5 51 25 77 Fax: +27 (021) 5 51 32 23 E-Mail: bsc@zsd.co.za Bosch Headquarters Midrand, Gauteng Tel.: +27 (011) 6 51 96 00 Fax: +27 (011) 6 51 98 80 E-Mail: rbsa-hq.pts@za.bosch.com Bosch Power Tools 1 609 929 X41 | (28.10.10) OBJ_BUCH-139-002.book Page 26 Thursday, October 28, 2010 9:38 AM 26 | English People's Republic of China China Mainland Bosch Power Tools (China) Co., Ltd. 567, Bin Kang Road Bin Jiang District 310052 Hangzhou, P.R.China Service Hotline: 400 826 8484 Fax: +86 571 8777 4502 E-Mail: contact.ptcn@cn.bosch.com www.bosch-pt.com.cn HK and Macau Special Administrative Regions Robert Bosch Hong Kong Co. Ltd. 21st Floor, 625 King's Road North Point, Hong Kong Customer Service Hotline: +852 (21) 02 02 35 Fax: +852 (25) 90 97 62 E-Mail: info@hk.bosch.com www.bosch-pt.com.hk Indonesia PT. Multi Tehaka Kawasan Industri Pulogadung Jalan Rawa Gelam III No. 2 Jakarta 13930 Indonesia Tel.: +62 (21) 46 83 25 22 Fax: +62 (21) 46 82 86 45/68 23 E-Mail: sales@multitehaka.co.id www.multitehaka.co.id Philippines Robert Bosch, Inc. 28th Floor Fort Legend Towers, 3rd Avenue corner 31st Street, Fort Bonifacio Global City, 1634 Taguig City, Philippines Tel.: +63 (2) 870 3871 Fax: +63 (2) 870 3870 matheus.contiero@ph.bosch.com www.bosch-pt.com.ph Bosch Service Center: 9725-27 Kamagong Street San Antonio Village Makati City, Philippines Tel.: +63 (2) 899 9091 Fax: +63 (2) 897 6432 rosalie.dagdagan@ph.bosch.com 1 609 929 X41 | (28.10.10) Bosch Power Tools OBJ_BUCH-139-002.book Page 27 Thursday, October 28, 2010 9:38 AM English | 27 Malaysia Robert Bosch (S.E.A.) Pte. Ltd. No. 8A, Jalan 13/6 G.P.O. Box 10818 46200 Petaling Jaya Selangor, Malaysia Tel.: +60 (3) 7966 3194 Fax: +60 (3) 7958 3838 cheehoe.on@my.bosch.com Toll-Free: 1800 880 188 www.bosch-pt.com.my Thailand Robert Bosch Ltd. Liberty Square Building No. 287, 11 Floor Silom Road, Bangrak Bangkok 10500 Tel.: +66 (2) 6 31 18 79 18 88 (10 lines) Fax: +66 (2) 2 38 47 83 Robert Bosch Ltd., P. O. Box 2054 Bangkok 10501, Thailand Bosch Service Training Centre 2869-2869/1 Soi Ban Kluay Rama IV Road (near old Paknam Railway) Prakanong District 10110 Bangkok Thailand Tel.: +66 (2) 6 71 78 00 4 Fax: +66 (2) 2 49 42 96 Fax: +66 (2) 2 49 52 99 Singapore Robert Bosch (SEA) Pte. Ltd. 11 Bishan Street 21 Singapore 573943 Tel.: +65 6571 2772 Fax: +65 6350 5315 leongheng.leow@sg.bosch.com Toll-Free: 1800 333 8333 www.bosch-pt.com.sg Vietnam Robert Bosch Vietnam Co. Ltd 10/F, 194 Golden Building 473 Dien Bien Phu Street Ward 25, Binh Thanh District 84 Ho Chi Minh City Vietnam Tel.: +84 (8) 6258 3690 ext. 413 Fax: +84 (8) 6258 3692 hieu.lagia@vn.bosch.com www.bosch-pt.com Bosch Power Tools 1 609 929 X41 | (28.10.10) OBJ_BUCH-139-002.book Page 28 Thursday, October 28, 2010 9:38 AM 28 | English Disposal Measuring tools, accessories and packaging should be sorted for environmental-friendly recycling. Do not dispose of measuring tools and batteries/rechargeable batteries into household waste! Only for EC countries: According to the European Guideline 2002/96/EC, measuring tools that are no longer usable, and according to the European Guideline 2006/66/EC, defective or used battery packs/batteries, must be collected separately and disposed of in an environmentally correct manner. Batteries no longer suitable for use can be directly returned at: Great Britain Robert Bosch Ltd. (B.S.C.) P.O. Box 98 Broadwater Park North Orbital Road Denham Uxbridge UB 9 5HJ Tel. Service: +44 (0844) 736 0109 Fax: +44 (0844) 736 0146 E-Mail: boschservicecentre@bosch.com Subject to change without notice. 1 609 929 X41 | (28.10.10) Bosch Power Tools