SilverStone HELA Series 850R Platinum / 750R Platinum

Key Features

• Support 12V-2x6 PCIe connector in compliance with ATX 3.1 standards
• High efficiency with 80 PLUS Platinum certification
• 100% modular cables
• 24/7 continuous power output with 50°C operating temperature
• All Japanese capacitors
• Silent running 120mm Fluid Dynamic Bearing (FDB) cooling fan
• Equipped with semi-fanless switch function
• 180° angled SATA connectors, ideal for systems with a parallel hard drive layout.

Specifications

1. AC Input Characteristics

1.1 AC Input Requirements:

1.2 AC Inrush Current (cold start): The power supply must meet inrush requirements for any rated AC voltage, during turn on at any phase of AC voltage, during a single cycle AC dropout condition, during repetitive ON/OFF cycling of AC, and over the specified temperature range (Top). The peak inrush current shall be less than the ratings of its critical components.

2. DC Output Characteristics

2.1 Output Voltage Regulation Requirements: The power supply output voltage must stay within the following voltage limits when operating at steady state.

Note: When the +12V is in the peak current load, the range of the voltage tolerance is about 10% of the standard output voltage.

2.2 Output Current Requirements: The power supply output current is shown below.

850W

Notes:
1. Maximum continuous total DC output power should not exceed 850W.
2. Maximum continuous combined load on +3.3V and +5V outputs shall not exceed 100W.
3. Peak DC output power should not exceed 900W for 12 seconds.
4. The 12V-2x6 connector Max load shall not exceed 37.5A (450W).

750W

Notes:
1. Maximum continuous total DC output power should not exceed 750W.
2. Maximum continuous combined load on +3.3V and +5V outputs shall not exceed 100W.
3. Peak DC output power should not exceed 800W for 12 seconds.
4. The 12V-2x6 connector Max load shall not exceed 37.5A (450W).

2.3 Output Transient Response: Table 4 summarizes the expected output transient step sizes for each output. The +3.3V & +5V transient load slew rate is = 1.0 A/μs. The +12V transient load slew rate is = 5.0 A/μs.

NOTES:
1. +12V 0~85% Load for +12V Min load 1A.
2. For example, for a rated +5 VDC output of 14A, the transient step would be 30% x 14 A = 4.2 A.
3. Output voltages should remain within the regulation limits of Section 2.1, and the power supply should stable when subjected to load transients per Table 3, from any steady state load, including any or all of the following conditions:
4. Simultaneous load steps on the +12 VDC, +5 VDC, and +3.3 VDC outputs (all steps occurring in the same direction)
5. Load-changing repetition rate of 50 Hz to 10 kHz
6. AC input range per Section 1.1 and Capacitive loading per Table 8

2.4 Output Ripple and Noise:

Note: This is measured over a bandwidth of 10Hz to 20MHz at the power supply output connector. A 10µF electrolytic capacitor in parallel with a 0.1µF ceramic capacitor is placed at the point of measurement.

Differential noise test setup

Figure 1

2.5 Efficiency:

2.5.1 In the 115Vac/60Hz input voltage

Note: There is a 0.5% tolerance in mass production.

2.5.2 ERP 5VSB Efficiency

2.6 Remote on/off control: When the logic level "PS-ON" is low, the DC outputs are to be enabled. When the logic level is high or open collector, the DC outputs are to be disabled.

2.7 Overshoot: The overshoot of the DC output voltage caused by switching AC power or switch PSON# should be less than 10% of the normal output, and no reverse polarity voltage should be produced.

2.8 Capacitance Loading: The power supply shall be stable and meet all requirements with the following capacitive loading ranges.

Environment

3.1 Operation temperature:

3.2 Shipping and Storage:

3.3 Altitude:

3.4 Cooling mode: Forced air cooling.

3.5 Random Vibration: Non-operating 0.01 g²/Hz at 5 Hz, sloping to 0.02 g²/Hz at 20 Hz, and maintaining 0.02 g²/Hz from 20 Hz to 500 Hz. The area under the PSD curve is 3.13 grams. The duration shall be 10 minutes per axis for all three axes on all samples.

Heat Dissipation Mode

Use a 12 centimeter fan to dissipate heat for the power supply.

Protection

Due to overvoltage, overpower, and short circuit, the protection function of the power supply circuit is self-operated, and the power is self-locked. There is no output at that time. When these reasons are removed, the power is restored to the normal output state when the power is restarted. (PSON# at least 1 second; AC shutdown at least 4 seconds).

5.1 Over-power protection: The power supply will be shutdown and latch off when output power is within 110~150% of rated DC output. Note: Assurance machine can work at low voltage, full load won't damage machine.

5.2 Over voltage protection:

5.3 Short circuit protection: An output short circuit is defined as any output impedance of less than 0.1 ohms. The power supply shall shut down and latch off for shorting the +3.3 VDC, +5 VDC, or +12VDC rails to return or any other rail. Shorts between main output rails and +5VSB shall not cause any damage to the power supply. The power supply shall either shut down and latch off or fold back for shorting the negative rails. +5VSB must be capable of being shorted indefinitely, but when the short is removed, the power supply shall recover automatically or by cycling PS_ON#. The power supply shall be capable of withstanding a continuous short-circuit to the output without damage or overstress to the unit.

5.4 Over Temperature Protection: The power supply will be protected against over temperature conditions caused by loss of fan cooling or excessive ambient temperature. In an OTP condition the PSU will shutdown. When the power supply temperature drops to within specified limits, the power supply shall Latch mode.

5.5 Over current protection: The power supply shall have current limit to prevent the +3.3V, +5V, and +12V outputs from exceeding the values shown in Table. If the current limits are exceeded, the power supply shall shutdown and latch off. The damaged from repeated power cycling in this condition. -12V and 5VSB shall be protected under over current or shorted conditions so that no damage can occur to the power supply. All outputs shall be protected so that no damage occurs to the power supply under a shorted output condition.

Power Supply Timing

6.1 Signal timing drawing: Figure 2 is a reference for signal timing for main power connector signals and rails.

Figure 2

The power supply should maintain output regulations per Table 5 despite a loss of input power at the low-end nominal range-115 VAC / 47 Hz or 230 VAC / 47 Hz – at maximum continuous output load as applicable for a minimum of 12ms (T5+T6).

7. SAFETY

The power supply designed to meet IEC 62368-1.

7.1 Electrical strength: Gradually increased from 0V to 1500V is applied in the AC line and the casing, and then keep for 1 minute, the insulation should not breakdown; if the current increases rapidly due to the test voltage and gets out of the way, that is to limit he current insulation, insulation breakdown that has occurred; corona discharge or flashover is not a single moment that is the breakdown of insulation.

7.2 Ground Resistance: Ground resistance value less than < 0.1 ohm(40A).

7.3 Touch current: When the input 250V, contact current less than 3.5mA.

7.4 EMC

• 7.4.1 ELECTROSTATIC DISCHARGE(ESD) – IEC 61000-4-2(EN61000-4-2).
• 7.4.2 RADIATED SUSCEPTIBILITY – IEC 61000-4-3(EN 61000-4-3).
• 7.4.3 ELECTRICAL FAST TRANSIENT / BURST (EFT/B) – IEC 61000-4-4(EN 61000-4-4).
• 7.4.4 SURGE – IEC 61000-4-5(EN 61000-4-5).
• 7.4.5 CONDUCTED SUSCEPTIBILITY – IEC 61000-4-6(EN 61000-4-6).
• 7.4.6 POWER FREQUENCY MAGNETIC FIELD – IEC 61000-4-8 (EN 61000-4-8).
• 7.4.7 VOLTAGE DIPS – IEC 61000-4-11(EN 61000-4-11).
• 7.4.8 VOLTAGE FLUCTUATIONS – IEC 61000-3-3 (EN 61000-3-3).
• 7.4.9 HARMONIC CURRENT EMISSION – IEC61000-3-2(EN 61000-3-2).
• 7.4.10 EN55032:Class B Radio interference (CISPR 32).
• 7.4.11 ANSI C63.4-2014 / FCC Part 15 Subpart B / ICES-003 Issue 6 Class B 115VAC operation.

8. Reliability

The demonstrated MTBF shall be 100,000 hours of continuous operation at 25°C and full load and 120Vac input voltage. The MTBF of the power supply shall be calculated in accordance with MIL-HDBK-217F. The DC FAN is not included.

9. Mechanical

9.1 Physical dimension: L140mm*W150mm*H86mm

10. POWER SUPPLY CONNECTOR OVERUSE DEFINITION

EN: Power supply connector overuse definition

A single PCIe 8pin cable and connector's maximum current rating is 12.5A, which is 150W (+12V x 12.5A). SilverStone's warranty will not cover damages or malfunction resulting from the use of a graphics card or expansion card with a single PCIe 8pin connector that exceeds standard 225W total power draw (150W from PCIe 8pin connector + 75W from PCIe motherboard slot). Similarly, a graphics card or expansion card with dual PCIe 8pin connectors that exceed 375W total power draw (300W from two PCIe 8pin connectors + 75W from PCIe motherboard slot) will also not be covered under warranty.

Peripheral (molex) or SATA connector's maximum current rating is 5A, which is 60W (+12V x 5A) or 25W (+5V x 5A). Please ensure connected devices are operating under these limits. SilverStone's warranty will not cover damages or malfunction resulting from usages exceeding these connectors and their associated cables.

24pin motherboard connector's maximum current rating for its dual +12V metal pins are 5A each, which totals 120W (+12V x 5A x 2). Please ensure +12V drawing devices connected to the motherboard are operating under these limits. SilverStone's warranty will not cover damages or malfunction resulting from usages exceeding these connectors and their associated cables.

DE: Definition einer Überlastung des Netzanschlusses

Die maximale Stromstärke eines einzelnen 8-poligen PCIe-Kabels und Anschlusses beträgt 12,5 A, was 150W (+12V x 12,5 A) entspricht. Daher deckt die SilverStone-Garantie keine Schäden oder Fehlfunktionen durch den Einsatz einer Grafikkarte oder Erweiterungskarte mit einem einzigen 8-poligen PCIe-Anschluss ab, die die Standardleistungsaufnahme von insgesamt 225 W übersteigt (150 W vom 8-poligen PCIe-Anschluss + 75 W vom PCIe-Motherboard-Steckplatz). Ebenso wird die Verwendung einer Grafikkarte oder Erweiterungskarte mit zwei 8-poligen PCIe-Anschlüssen, die eine Leistungsaufnahme von insgesamt 375 übersteigen (300 W von den beiden 8-poligen PCIe-Anschlüssen + 75 W vom PCIe-Motherboard-Steckplatz) nicht durch die Garantie abgedeckt.

Der maximale Nennstrom von Peripherie- (Molex) oder SATA-Anschluss beträgt 5 A, was 60 W (+12 V x 5 A) oder 25 W (+5 V x 5 A) entspricht. Bitte achten Sie darauf, dass verbundene Geräte unter diesen Grenzwerten arbeiten. Die Garantie von SilverStone deckt keine Schäden oder Fehlfunktionen aufgrund einer Nutzung ab, die diese Anschlüsse und ihre zugehörigen Kabel übersteigt.

Der maximale Nennstrom des 24-poligen Motherboard-Anschlusses für seine dualen +12V-Metallkontakte beträgt jeweils 5 A, was insgesamt 120 W (+12 V x 5 A x 2) ergibt. Bitte stellen Sie sicher, dass mit dem Motherboard verbundene +12V-Geräte unter diesen Grenzwerten arbeiten. SilverStones Garantie deckt keine Schäden oder Fehlfunktionen aufgrund einer Nutzung jenseits der Angaben dieser Anschlüsse und ihrer zugehörigen Kabel ab.

FR: Définition de l'utilisation excessive du connecteur d'alimentation électrique

Le courant nominal maximum d'un câble et d'un connecteur PCIe 8 broches unique est de 12,5 A, ce qui correspond à 150 W (+12 V x 12,5 A). La garantie de SilverStone ne couvre donc pas les dommages ou les dysfonctionnements résultant de l'utilisation d'une carte graphique ou d'une carte d'extension avec un connecteur PCle 8 broches unique qui dépasse une consommation énergétique totale de 225 W standard (150 W provenant du connecteur PCIe 8 broches + 75 W provenant de l'emplacement de la carte mère PCIe). De même, une carte graphique ou une carte d'extension avec deux connecteurs PCle 8 broches qui dépasse une consommation énergétique totale de 375 W (300 W provenant des deux connecteurs PCIe 8 broches + 75 W provenant de l'emplacement de la carte mère PCIe) ne sera également pas couverte dans le cadre de la garantie.

Le courant nominal maximum d'un périphérique (Molex) ou d'un connecteur SATA est de 5 A, ce qui correspond à 60 W (+12 V x 5 A) ou 25 W (+5 V x 5 A). Veuillez vous assurer que les appareils connectés fonctionnent dans ces limites. La garantie de SilverStone ne couvre pas les dommages ou les dysfonctionnements résultant d'utilisations dépassant ces connecteurs et leurs câbles associés.

Le courant nominal maximal des connecteurs 24 broches de la carte mère pour ses doubles broches métalliques +12 V est de 5 A chacun, ce qui représente au total 120 W (+12 V x 5 A x 2). Veuillez vous assurer que les dispositifs de tension +12 V connectés à la carte mère fonctionnent dans ces limites. La garantie de SilverStone ne couvre pas les dommages ou les dysfonctionnements résultant d'utilisations dépassant la capacité de ces connecteurs et de leurs câbles associés.

IT: Definizione di uso eccessivo del connettore di alimentazione

La corrente massima di un singolo cavo PCle a 8 pin e del connettore è 12,5 A, corrispondente a 150 W (+12 V x 12,5 A). Pertanto, la garanzia di SilverStone non copre danni o malfunzionamenti derivanti dall'utilizzo di una scheda grafica o una scheda di espansione con un singolo connettore PCle a 8 pin che supera l'assorbimento totale di 225 W (150 W da connettore PCle a 8 pin + 75 W da slot PCIe). Analogamente, la garanzia non copre anche una scheda grafica o una scheda di espansione con doppi connettori PCle a 8 pin che superano l'assorbimento totale di 375 W (300 W da doppi connettori PCle a 8 pin + 75 W dalla scheda madre PCIe).

La corrente massima del connettore periferico (molex) o SATA è 5 A, corrispondente a 60 W (+12 V x 5 A) o 25 W (+5 V x 5 A). Assicurarsi che i dispositivi collegati funzionino entro questi limiti. La garanzia di SilverStone non copre danni o malfunzionamenti derivanti da uso eccessivo di questi connettori e dei relativi cavi.

La corrente massima del connettore a 24 pin per scheda madre per i suoi due pin di metallo a +12 V è di 5 A ciascuno, per un totale di 120 W (+12 V x 5 A x 2). Assicurarsi che i dispositivi a +12 V collegati alla scheda madre funzionino con questi limiti. La garanzia di SilverStone non copre danni o malfunzionamenti derivanti da uso eccessivo di questi connettori e dei relativi cavi.

ES: Definición de uso excesivo del conector de la Fuente de alimentación

La corriente máxima de un solo cable PCle de 8 pines es 12,5A, lo que son 150W (+12V x 12,5A). Por tanto, la garantía de SilverStone no cubrirá daños o fallos provocados por el uso de una tarjeta gráfica o de expansión con un único conector PCle de 8 pines que exceda el total estándar de 225W (150W del conector PCle de 8 pines + 75W del zócalo PCle de la placa base). De igual modo, una tarjeta gráfica o de expansión con conectores duales PCle de 8 pines que superen 375W de potencia (300W de los dos conectores PCle de 8 pines + 75W del zócalo de la placa base) tampoco será cubierta por la garantía.

La corriente máxima del conector de periféricos (molex) o SATA es 5A, que son 60W (+12V x 5A) o 25W (+5V x 5A). Por favor, asegúrese de que los dispositivos conectados funcionan dentro de estos límites. La garantía de SilverStone no cubrirá daños o fallos a resultas de un uso excesivo de estos conectores y sus cables asociados.

La corriente máxima del conector de 24 pines de la placa base para sus pines de metal duales de +12V es de 5A cada uno, para un total de 120W (+12V x 5A x 2). Por favor, asegúrese de que los dispositivos de +12V conectados a la placa base funcionan dentro de estos límites. La garantía de SilverStone no cubrirá daños o averías a resultas de un uso excesivo para estos conectores y sus cables asociados.

RU: Определение чрезмерной нагрузки на коннектор блока питания

Один кабель и коннектор PCIe 8pin поддерживает ток 12.5А, что равно 150Вт (+12В х 12.5А). Таким образом, гарантийные обязательства SilverStone не будут действовать если вы используете видеокарту или другую карту расширения с одним коннектором PCIe 8pin, которые превышает стандартную общую потребляемую мощность 225Вт (150Вт через коннектор PCIe 8pin + 75Вт через слот PCIe материнской платы). Аналогично, видеокарта или другая карта расширения с двумя коннекторами PCIe 8pin, которые превышают общую потребляемую мощность 375Вт (300Вт через коннектор PCIe 8pin + 75Вт через слот PCIe материнской платы), также не будут покрываться гарантией.

Максимальный номинальный ток периферийного (molex) или SATA разъёма составляет 5А, что равно 60Вт (+12В х 5А) или 25Вт (+5В х 5А). Пожалуйста, убедитесь, что подключенные устройства работают в этих пределах. Гарантия SilverStone не будет распространяться на неисправности, возникающие в результате использования этих коннекторов или подключаемых к ним кабелей.

Максимальный номинальный ток 24pin коннектора материнской платы для его двойных металлических контактов +12В составляет 5А на каждый, что равно 120Вт (+12В х 5А х 2). Пожалуйста, убедитесь, что устройства, подключенные к линии +12В, работают в этих пределах. Гарантия SilverStone не будет распространяться на неисправности, возникающие в результате использования этих коннекторов или подключаемых к ним кабелей.

KR: 전원 공급 커넥터 과용 정의

단일한 PCIe 8핀 케이블 및 커넥터의 최대 전류 정격은 12.5A로서 전력으로 환산하면 150W(+12V x 12.5A)입니다. SilverStone의 보증에서는 표준 225W의 총 소비 전력 (PCIe 8핀 커넥터의 150W와 PCle 메인보드 슬롯의 75W의 합)을 초과하는 단일 PCle 8핀 커넥터 탑재 그래픽 카드나 확장 카드를 사용하여 발생하는 손상 또는 오작동을 보상하지 않습니다. 이와 마찬가지로 375W의 총 소비 전력(PCle 8핀 커넥터 2개의 300W와 PCle 메인보드 슬롯의 75W의 합)을 초과하는 듀얼 PCIe 8핀 커넥터 탑재 그래픽 카드나 확장 카드를 사용해도 보증에서 보상해주지 않습니다.

주변장치(molex) 또는 SATA 커넥터의 최대 전류 정격은 5A로서 전력으로 환산하면 60W(+12V x 5A) 또는 25W(+5V x 5A)입니다. 연결된 장치들은 이러한 제한 하에서만 작동시켜야 합니다. SilverStone 의 보증에서는 이러한 커넥터 및 이와 연결되는 케이블의 정격을 초과하여 사용함으로써 발생하는 손상이나 오작동을 보상하지 않습니다.

듀얼 +12V 금속 핀에 사용되는 24핀 메인보드 커넥터의 정격 전류는 5A 이며, 각각 합계가 120W (+12V x 5A x 2) 입니다. 메인보드에 연결된 +12V 장치가 해당 한계 미만으로 작동되도록 하십시오. SilverStone은 이 커넥터나 관련 케이블의 한계를 초과해서 사용함으로써 발생하는 손상이나 고장에 대해서 보장하지 않습니다.

JP: 電力供給コネクタの使用限度超過に関する説明

単一のPCIe 8ピンケーブルおよびコネクタの最大定格電流は12.5Aで150W (+12V x 12.5A)となります。それで定格225W合計電力消費(PCIe 8ピンコネクタからの150W + PCIeマザーボードスロットからの75W)を超える、単一PCIe 8ピンコネクタ装備のグラフィックスカードまたは拡張カード使用によって生じた損傷や故障の場合、SilverStoneの製品保証は適用外となります。同様に、375W合計電力消費(2基のPCIe 8ピンコネクタからの300W + PCIeマザーボードスロットからの75W)を超える、デュアルPCIe 8ピンコネクタ装備のグラフィックスカードまたは拡張カード使用によって生じた損傷や故障の場合も、製品保証適用外となります。

周辺用 (molex)またはSATAコネクタの最大定格電流は5Aで、60W (+12V×5A)または25W (+5Vx5A)となります。接続された装置がこれら限度以内で動作することを確認してください。これらコネクタおよび関連ケーブルの定格を超える使用法で生じた損傷や故障については、SilverStone製品保証対象外となりますのでご注意ください。

24ピンマザーボードコネクタのデュアル+12V金属製ピンに対する最大定格電流はそれぞれ5Aなので合計は120W (+12V×5A×2)となります。接続される+12V入力のデバイスが、これら上限以内で動作することを確認してください。これらコネクタおよび関連ケーブルでの限界を超えた使用で生じた損傷または故障は、SilverStoneによる製品保証対象外となります。

TW: 電源供應器接頭過度使用定義

單條PCle 8pin電源線與接頭的最大額定電流為12.5A,瓦特數150W(+ 12V x 12.5A)。因此,銀欣的電源保固不包括用於單條PCIe 8pin接頭之顯卡/擴充卡,在超過標準225W總功耗範圍所造成的損壞或故障(150W 的PCIe 8pin接頭+75W的主機板PCIe插槽)。以此類推,若具備雙PCle 8pin接頭的顯卡/擴充卡,負載一但超過375W總功耗,視同不屬保固範圍內(300W來自兩個PCIe 8pin接頭 + 75W的主機板PCIe插槽)。

大4pin (molex)或SATA接頭的最大額定電流為5A,即60W (+ 12V x 5A)或25W(+5V × 5A)。請確保連接的設備皆低於此限制下運行 銀欣不保固超出電源供應器接頭及其相關線材之使用負載上限所造成的損壞或故障。

24pin主機板接頭的雙+12V金屬針腳最大額定電流為5A,即120W(+ 12V x 5A x 2)。請確保連接的+12V設備皆低於此限制下運行。 銀欣不保固超出電源供應器接頭及其相關線材之使用負載上限所造成的損壞或故障。

CN: 电源供应器接头过度使用定义

单条PCle 8pin电源线与接头的最大额定电流为12.5A,瓦特数150W(+ 12V x 12.5A)。因此,银欣的电源保固不包括用于单条PCle 8pin接头之显卡/扩充卡,在超过标准225W总功耗范围所造成的损坏或故障(150W 的PCIe 8pin接头+ 75W的主板PCIe插槽)。以此类推,若具备双PCIe 8pin接头的显卡/扩充卡,负载一但超过375W总功耗,视同不属保固范围内(300W来自两个PCle 8pin接头 + 75W的主板PCIe插槽)。

大4pin (molex)或SATA接头的最大额定电流为5A,即60W (+ 12V x 5A)或25W(+5V x 5A)。请确保连接的设备皆低于此限制下运行 银欣不保固超出电源供应器接头及其相关线材之使用负载上限所造成的损坏或故障。

24pin主板接头的双+12V金属针脚最大额定电流为5A,即120W (+ 12V x 5A x 2)。请确保连接的+12V设备皆低于此限制下运行。 银欣不保固超出电源供应器接头及其相关线材之使用负载上限所造成的损坏或故障。

警告:

1. M 仅适用于海拔2000m及以下地区安全使用。
2. 本产品不得受水滴或水溅,设备上不应放置诸如花瓶一类的等装满液体的物品。
3. |类结构的设备应当连接到带保护接地连接的电网电源输出插座上。
4. 本产品以器具耦合器作为断开装置,在设备正常使用时要确保断开装置能方便触及到。
5. 在居住环境中,运行此设备可能会造成无线干扰。

TH: ขีดจำกัดการรองรับการใช้งานของขั้วต่อจากพาวเวอร์ซัพพลาย

สําหรับขั้วเชื่อมต่อและสายไฟเลี้ยง PCIe 8 พินสามารถรองรับกระแสได้สูงสุด 12.5 แอมป์หรือหมายถึง 150 วัตต์ (+12V x 12.5A) ดังนั้นการรับประกันจากทาง SilverStone จะไม่ครอบคลุมถึงความเสียหายหรือความผิดปรกติซึ่งเกิดขึ้นกับกราฟิกการ์ดรวมถึงการ์ดขยายความยาวที่ใช้งานขั้วเชื่อมต่อ PCIe 8 พิน ซึ่งมันมีการใช้พลังงานรวมทั้งสิ้นเกินกว่ามาตรฐานที่กำหนดคือ 225 วัตต์ (150 วัตต์ จาก PCIe 8 พิน + 75 วัตต์ จากสล๊อต PCIe บนเมนบอร์ด) อันรวมถึงกราฟิการ์ดหรือการ์ดขยายความยาวที่ใช้ขั้วต่อไฟเลี้ยง PCIe 8 พินจํานวน 2 ชุดซึ่งมีการใช้พลังงานทั้งสิ้น 375 วัตต์ (300 วัตต์ จากขั้ว PCIe 8 พิน 2 ชุด + 75 วัตต์ จากสล๊อต PCIe บนเมนบอร์ด) ซึ่งไม่ครอบคลุมเช่นกัน ภายใต้การรับประกัน ขั้วเชื่อมต่อ Peripheral หรือ Molex 4 พินและ SATA มันสามารถรองรับกระแสได้สูงสุด 5 แอมป์หรือหมายถึง 60 วัตต์ (+12V x 5A) หรือ (+5V + 5A) กรุณาให้แน่ใจว่าอุปกรณ์ที่ใช้งานมีการใช้พลังงานไม่เกินกว่าขีดจำกัดที่รองรับ ดังนั้นการรับประกันจากทาง SilverStone จะไม่ครอบคลุมถึงความเสียหายหรือความผิดปรกติจากอุปกรณ์ที่เชื่อมต่อใช้งานจากตัวสายเชื่อมต่อซึ่งมีการใช้พลังงานเกินกว่าขีดจำกัด

กระแสไฟฟ้าสูงสุดของขั้วต่อเมนบอร์ด 24 พิน สำหรับพินโลหะ +12V คู่แต่ละอันมีค่า 5A ซึ่งรวมทั้งหมดเป็น 120W (+12V x 5A x 2) โปรดตรวจสอบให้มั่นใจว่าอุปกรณ์ตัวดึงพลังงาน +12V ที่เชื่อมต่อกับเมนบอร์ดสามารถทำงานภายใต้ขีดจำกัดเหล่านี้ได้ การรับประกันของ SilverStone ไม่คุ้มครองความเสียหาย หรืออาการเสียที่เป็นผลจากการใช้เกินขีดจำกัดของขั้วต่อและสายเคเบิลที่ใช้เชื่อมต่อเหล่านี้

Installation Requirements

1. For user safety and fire prevention purposes, when installing this switching power supply, it must be installed in an enclosure that meets the following requirements, and only then connected to power after proper installation.

• 1-1. The enclosure material must be fire-resistant.
• 1-2. The maximum inner diameter of circular openings on the top and sides of the enclosure must not exceed 5mm.
• 1-3. For rectangular openings on the top and sides of the enclosure, the diagonal distance must not exceed 5mm; if the width is less than 1mm, the length is not restricted.
• 1-4. There must be no openings on the bottom of the enclosure.

2. This product outputs dangerous energy. To avoid danger during operation, the power must only be turned on after the system chassis is assembled and all equipment is properly installed.

3. This product's power output is not a power-limited power source. Please connect it with peripherals that have a fire-resistant enclosure to prevent fire hazards.

BSMI ROHS Information: https://www.silverstonetek.com/upload/downloads/PSU/RSD.pdf

Switching Power Supply Hazardous Substances/Elements and Their Chemical Content Table

This table is prepared in accordance with SJ/T 11364.

○: Indicates that the content of the hazardous substance in all homogeneous materials of this part is below the limit requirement specified in GB/T 26572.
X: Indicates that the content of the hazardous substance in at least one homogeneous material of this part exceeds the limit requirement specified in GB/T 26572.

Product Certificate

Inspector: 检01
Production Date: See product barcode

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• (1) this device may not cause harmful interference, and
• (2) this device must accept any interference received, including interference that may cause undesired operation.

Model (safety certification):SST-AX0850MCPT-C / SST-AX0750MCPT-C
The equipment a Class I Switching Power Supply intended to use for information technology equipment or Audio and Video equipment.

※The included power cord is for this product only. Do not use it with other devices.

Please refer to SilverStone website for latest specifications updates.