Black & Decker Workmate® 225 Type 5 Instruction Manual

Important Safety Instructions

WARNING: Read and understand all safety instructions before use.

• Do not load with more than 450 pounds (204 kg).
• Do not apply an unbalanced load that could cause tipping.
• Do not use as a stepladder or standing platform. The footboard is a foot REST only.
• Do not store outdoors or in damp locations.
• Avoid excessive force when clamping with swivel pegs.
• Ensure legs are fully open and the table locks in position.
• Follow power tool safety instructions when using with the Workmate.
• Always wear safety glasses when operating power tools.
• Ensure even pressure from vise jaws by tightening crank handles uniformly.

Assembly Instructions

The Workmate® 225 Type 5 comes partially assembled. A standard hammer and the included plastic socket wrench are required.

Step 1: Identify Components

Empty the box and identify all parts as shown in Figure 1. Key components include:

• Frame (A)
• Front Vise Jaw (B)
• Rear Vise Jaw (C)
• Vise Screws (D)
• Pivot Nuts (E)
• Vise Cranks (F)
• Crank Handle (G)
• Swivel Pegs (H)
• Front Top Blocks (K)
• Rear Top Blocks (L)
• Bolts (M)
• Pins (N)
• Washers (P)
• Rubber Feet

Step 2: Frame Setup

Place the frame (A) on the floor. Locate the release levers near the front rubber feet. Depress both levers and pull up until the frame locks in position (see Figure 2).

Step 3: Vise Jaw Bracket Assembly

1. Screw a pivot nut (E) onto each vise screw (D) about halfway. Assemble a washer (P) onto each vise screw (see Figure 3).
2. Insert the unthreaded end of the vise screws into the frame, ensuring pivot nuts are in the frame slots and unthreaded ends protrude through the front holes (Figures 3 & 4).
3. Install the two vise cranks (F) by driving pins (N) through the aligned holes in the cranks and vise screws. Strike pins with a hammer until flush (see Figure 5).

Step 4: Top Blocks and Jaw Installation

Note that front top blocks (K) do not have a protruding tab on the bottom, unlike rear top blocks (L).

1. Select the front vise jaw (B) and the two front top blocks (K). Place top blocks on frame rails (Figure 6).
2. Position the front vise jaw on the top blocks, aligning small holes with posts. Insert into the frame.
3. Insert two bolts (M) through the jaw holes and tighten into the pivot nuts using the socket wrench (J) (Figure 1). Perform on both sides.
4. Select the rear vise jaw (C) and two rear top blocks (L). Position rear top blocks on frame rails, fitting tab ears into key holes. Ensure raised posts face the rear (Figure 7).
5. Install the rear vise jaw, aligning small holes with the posts on the rear top blocks.
6. Insert the remaining two bolts (M) through the jaw and top blocks into the vise guide posts. Note that rear block holes are not threaded.

Step 5: Crank Handle and Rubber Feet Installation

1. Snap in the crank handles as shown in Figure 8.
2. To install rubber feet: Turn the unit upside down. Extend and lock the four legs. Align a rubber foot with each leg and lightly tap into place with a hammer (Figure 9).

Step 6: Changing Indexed Position of the Rear Jaw

Install the rear jaw in one of three indexed "keyhole" positions by aligning it with a keyhole in the vise jaw bracket and sliding it to the back of the keyhole (Figure 7).

Step 7: Using Swivel Pegs

The four swivel pegs (H) can be used in any of the holes in the front and rear jaws to extend holding capacity (Figure 10).

Service Information

Black & Decker provides a network of company-owned and Authorized Service locations. For technical advice, repair, or genuine replacement parts, contact your nearest Black & Decker service location. Refer to the yellow pages under "Tools-Electric" or call 1-800-54-HOW-TO (544-6986).

Visit: www.blackanddecker.com

Full Two-Year Home Use Warranty

Black & Decker (U.S.) Inc. warrants this product for two years against defects in material or workmanship. Defective products will be replaced or repaired at no charge.

Warranty Options:

• Retailer Return: Return the product to the retailer where purchased within their exchange policy period (typically 30-90 days). Proof of purchase may be required.
• Service Center: Take or send the product (prepaid) to a Black & Decker owned or Authorized Service Center for repair or replacement. Proof of purchase may be required.

This warranty does not apply to accessories. It grants specific legal rights that may vary by state.

This product is not intended for commercial use.

Diagram Descriptions

Figure 1: Components Overview
Illustrates the Workmate 225 with various parts labeled, including the frame, vise jaws, crank handle, folding legs, swivel pegs, and top blocks.

Figure 2: Frame Locking Mechanism
Shows how to depress release levers and pull up the frame to lock it into the workbench position.

Figure 3: Vise Screw and Pivot Nut Assembly
Depicts assembling a pivot nut onto a vise screw and adding a washer.

Figure 4: Vise Screw Insertion
Illustrates inserting the vise screw into the frame, with the pivot nut in the slot and the screw end protruding.

Figure 5: Vise Crank and Pin Installation
Shows aligning the vise crank with the vise screw and inserting a pin to secure them.

Figure 6: Front Jaw and Top Blocks Installation
Details placing the front top blocks onto the frame rails and then installing the front vise jaw onto these blocks, securing with bolts.

Figure 7: Rear Jaw and Top Blocks Installation / Indexed Positions
Explains positioning the rear top blocks (with tabs) and the rear vise jaw, and shows the three indexed positions for the rear jaw.

Figure 8: Crank Handle Attachment
Shows how to snap the crank handle onto the vise screw.

Figure 9: Rubber Foot Installation
Illustrates attaching the rubber feet to the ends of the Workmate legs.

Figure 10: Swivel Pegs Usage
Demonstrates using the swivel pegs in the jaw holes to increase holding capacity.