Coyote S-Series 36-Inch 4-Burner Freestanding Gas Grill
C2C36 INSTALL GUIDE DIMENSIONAL RENDERINGS 37 5 /8" 23" 35 3/4" 11" 22 1 /8" Overall Product Dimensions Model No. C2C36 CJAKTCS36 Height 23" 11" Width 35 1/2" 37 5/8" Depth 25 1/2" 23" Cutout Dimensions for Island Model No. C2C36 CJAKTCS36 Height 10 1/4" 11" Width 32 1/2" 35 3/4" Depth 20 1/2" 22 1/8" When using a Coyote insulated jacket, you will want to build your island to the jackets Cutout and Overall Dimensions listed above (detailed on 2nd page). Once the jacket is installed, the grill will rest on/inside the insulated jacket Model No. C2C36LP C2C36NG Gas Supply Propane Natural Gas BTU's 80,000 80,000 Regulator WC Pressure Max PSI 20 lb Tank Regulator 11" .5 PSI 1/2" Female Pipe 4" .5 PSI Electrical Requirements Qty 1 - 120 VAC 60 Hz Grounded Plug Qty 1 - 120 VAC 60 Hz Grounded Plug Important Note to Installer: This file is not intended to replace your Owners' Manual which contains specific safety requirements and consumer guidelines. Please refer to your Owners' Manual prior to installing or operating your built-in grill. www.coyoteoutdoor.com C2C36 INSTALL GUIDE NON-COMBUSTIBLE CONSTRUCTION Insulated Jacket NOT Required 1 1/2" TOP VIEW GRILL OPENING 1 5/8" 24" 24" 2 1/2" G 24" 20 1/2" OPENING DEPTH GAS CONNECTION 2 1/2" 1 1/2" GRILL OVERHANG COMBUSTIBLE CONSTRUCTION Insulated Jacket Required - Model # CJAKTCS36 TOP VIEW LINER OPENING 7/8" 1 3/4" 221/8" OPENING DEPTH 4 1/8" G GAS CONNECTION 4 1/8" 7/8" JACKET OVERHANG 10 1/4" OPENING HEIGHT INCLUDING COUNTERTOP 32 1/2" OPENING WIDTH 21/2" 2" G 1 1/2" MIN DOORS / DRAWERS OPENING WIDTH OPENING HEIGHT 11" OPENING HEIGHT INCLUDING COUNTERTOP 35 3/4" OPENING WIDTH 4 1/8" 2 3/4" G 1 1/2" MIN DOORS / DRAWERS OPENING WIDTH OPENING HEIGHT FRONT VIEW Combustible material can not be within 24" of the grills frame This applies to all directions - horizontal & vertical Shaded area above on "TOP VIEW" illustrates the 24" minimum requirement (not to scale for rendering purposes) The grill is designed to hang from the counter top with no support underneath Minimum rear clearance for the hood to open is 2" If you have a wall/partition behind the grill, the minimum rear clearance to that wall should be at least 7" to allow for ventilation of the exhaust FRONT VIEW If using combustible material within 24" of the grill frame, you MUST use the corresponding Coyote Insulated Jacket Using a insulated jacket, does not waive any other standard installation procedure (ventilation, connections, etc) The jacket is designed to hang from the counter top with no support underneath Minimum clearance for hood to open is 2" If you have a wall/partition behind the grill, the minimum rear clearance to that wall should be at least 7" to allow for ventilation of the exhaust Ventilation Requirements: Regardless if you are using a combustible or non-combustible building material, you must include at least two vents within the island. These vents must be at least 20 sq. in. each and allow fresh air to move from the grill cabinet to the exterior environment. For a propane setup, the vents should be installed lower as propane is heavier than air. For a natural gas setup, the vents should be located higher in the island, as natural gas is lighter than air. Do not locate the two vents on the same wall of the island. Cross ventilation is key to allow any excess heat or trapped gas to dissipate. Important Note to Installer: This file is not intended to replace your Owners' Manual which contains specific safety requirements and consumer guidelines. Please refer to your Owners' Manual prior to installing or operating your built-in grill. www.coyoteoutdoor.comGPL Ghostscript 9.52 Adobe InDesign CC 2015 (Macintosh)