2020-06-15 —
Maintenance and Service Guide SUMMARY This guide provides information about spare parts, removal and replacement of parts, security, backing up, and more. © Copyright 2020 HP Development Company, L.P. Bluetooth is a trademark owned by its proprietor and used by HP Inc. under license. Intel, Optane, Thunderbolt, and XMM are trademarks of Intel Corporation or its subsidiaries in the U.S. and/or other countries. Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. NVIDIA and GeForce are trademarks and/or registered trademarks of NVIDIA Corporation in the U.S. and other countries. USB Type-C and USB-C are registered trademarks of USB Implementers Forum. DisplayPortTM and the DisplayPortTM logo are trademarks owned by the Video Electronics Standards Association (VESA®) in the United States and other countries. Miracast is a registered trademark of Wi-Fi Alliance. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. First Edition: June 2020 Document Part Number: M02981-001 Product notice This guide describes features that are common to most models. Some features may not be available on your computer. Not all features are available in all editions or versions of Windows. Systems may require upgraded and/or separately purchased hardware, drivers, software or BIOS update to take full advantage of Windows functionality. Windows 10 is automatically updated, which is always enabled. ISP fees may apply and additional requirements may apply over time for updates. Go to http://www.microsoft.com for details. To access the latest user guides, go to http://www.hp.com/support, and follow the instructions to find your product. Then select Manuals. Software terms By installing, copying, downloading, or otherwise using any software product preinstalled on this computer, you agree to be bound by the terms of the HP End User License Agreement (EULA). If you do not accept these license terms, your sole remedy is to return the entire unused product (hardware and software) within 14 days for a full refund subject to the refund policy of your seller. For any further information or to request a full refund of the price of the computer, please contact your seller. Important notice about Customer Self-Repair parts Your computer includes Customer Self-Repair Parts and parts that should be accessed by only an authorized service provider. IMPORTANT: See "Removal and replacement procedures for Customer Self-Repair parts" for details. Accessing parts described in "Removal and replacement procedures for authorized service provider parts" can damage the computer or void your warranty. iii iv Important notice about Customer Self-Repair parts Safety warning notice Reduce the possibility of heat-related injuries or of overheating the computer by following the practices described. WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to come into contact with the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer and the AC adapter comply with the user-accessible surface temperature limits defined by applicable safety standards. v vi Safety warning notice Table of contents 1 Product description ....................................................................................................................................... 1 2 Components .................................................................................................................................................. 7 Right side ............................................................................................................................................................... 7 Left side ................................................................................................................................................................. 8 Display .................................................................................................................................................................... 9 Keyboard area ...................................................................................................................................................... 10 Touchpad components ...................................................................................................................... 10 Lights ................................................................................................................................................. 11 Button, speakers, and fingerprint reader ......................................................................................... 12 Special keys ....................................................................................................................................... 14 Hot keys (select products only) ......................................................................................................... 15 Bottom ................................................................................................................................................................. 15 Labels ................................................................................................................................................................... 16 3 Illustrated parts catalog .............................................................................................................................. 18 Computer major components .............................................................................................................................. 18 Display assembly subcomponents ...................................................................................................................... 21 Bracket Kit ............................................................................................................................................................ 23 Plastics Kit ........................................................................................................................................................... 23 Cable Kit ............................................................................................................................................................... 24 Miscellaneous parts ............................................................................................................................................. 24 4 Removal and replacement procedures preliminary requirements .................................................................... 27 Tools required ...................................................................................................................................................... 27 Service considerations ......................................................................................................................................... 27 Plastic parts ....................................................................................................................................... 27 Cables and connectors ...................................................................................................................... 27 Drive handling ................................................................................................................................... 27 Workstation guidelines ..................................................................................................................... 28 Electrostatic discharge information .................................................................................................................... 28 Generating static electricity .............................................................................................................. 29 Preventing electrostatic damage to equipment ............................................................................... 29 Personal grounding methods and equipment .................................................................................. 30 Grounding the work area ................................................................................................................... 30 Recommended materials and equipment ........................................................................................ 30 vii Packaging and transporting guidelines .............................................................................................................. 31 5 Removal and replacement procedures for Customer Self-Repair parts ............................................................. 32 Component replacement procedures .................................................................................................................. 32 Preparation for disassembly ............................................................................................................. 32 Bottom cover ..................................................................................................................................... 32 Memory modules ............................................................................................................................... 33 WLAN module .................................................................................................................................... 36 WWAN module ................................................................................................................................... 38 Solid-state drive ................................................................................................................................ 40 6 Removal and replacement procedures for authorized service provider parts .................................................... 41 Component replacement procedures .................................................................................................................. 41 Preparation for disassembly ............................................................................................................. 41 Battery ............................................................................................................................................... 41 RTC battery ........................................................................................................................................ 43 Card reader board .............................................................................................................................. 43 Power connector cable ...................................................................................................................... 44 USB board .......................................................................................................................................... 45 Fingerprint reader board ................................................................................................................... 46 Touchpad ........................................................................................................................................... 47 NFC module ....................................................................................................................................... 49 Fan ..................................................................................................................................................... 49 Heat sink ............................................................................................................................................ 50 System board .................................................................................................................................... 53 Speakers ............................................................................................................................................ 56 Display assembly ............................................................................................................................... 57 Keyboard with top cover ................................................................................................................... 72 7 Computer Setup (BIOS), TPM, and HP Sure Start ............................................................................................. 73 Using Computer Setup ......................................................................................................................................... 73 Navigating and selecting in Computer Setup ................................................................................... 73 Restoring factory settings in Computer Setup ................................................................................. 73 Updating the BIOS ............................................................................................................................. 74 Determining the BIOS version ......................................................................................... 74 Preparing for a BIOS update ........................................................................................... 74 Downloading a BIOS update ......................................................................... 74 Installing a BIOS update ............................................................................... 75 Changing the boot order using the f9 prompt .................................................................................. 75 TPM BIOS settings (select products only) ........................................................................................................... 75 viii Using HP Sure Start (select products only) ......................................................................................................... 76 8 Backing up, restoring, and recovering ........................................................................................................... 77 Backing up information and creating recovery media ........................................................................................ 77 Using Windows tools ......................................................................................................................... 77 Using the HP Cloud Recovery Download Tool to create recovery media (select products only) ..... 77 Restoring and recovery ........................................................................................................................................ 78 Restoring, resetting, and refreshing using Windows tools .............................................................. 78 Recovering using HP Recovery media ............................................................................................... 78 Changing the computer boot order ................................................................................................... 78 Using HP Sure Recover (select products only) .................................................................................. 79 9 Using HP PC Hardware Diagnostics ................................................................................................................ 80 Using HP PC Hardware Diagnostics Windows (select products only) ................................................................. 80 Using an HP PC Hardware Diagnostics Windows hardware failure ID code ...................................... 80 Accessing HP PC Hardware Diagnostics Windows ............................................................................ 80 Accessing HP PC Hardware Diagnostics Windows from HP Help and Support .............. 80 Accessing HP PC Hardware Diagnostics Windows from Support Assistant ................... 81 Downloading HP PC Hardware Diagnostics Windows ....................................................................... 81 Downloading the latest HP PC Hardware Diagnostics Windows version from HP ......... 81 Downloading the HP PC Hardware Diagnostics Windows from the Microsoft Store ..... 81 Downloading HP Hardware Diagnostics Windows by product name or number (select products only) ..................................................................................................... 81 Installing HP PC Hardware Diagnostics Windows ............................................................................. 82 Using HP PC Hardware Diagnostics UEFI ............................................................................................................. 82 Using an HP PC Hardware Diagnostics UEFI hardware failure ID code ............................................. 82 Starting HP PC Hardware Diagnostics UEFI ....................................................................................... 82 Downloading HP PC Hardware Diagnostics UEFI to a USB flash drive .............................................. 83 Downloading the latest HP PC Hardware Diagnostics UEFI version .............................. 83 Downloading HP PC Hardware Diagnostics UEFI by product name or number (select products only) ..................................................................................................... 83 Using Remote HP PC Hardware Diagnostics UEFI settings (select products only) ............................................. 83 Downloading Remote HP PC Hardware Diagnostics UEFI ................................................................. 84 Downloading the latest Remote HP PC Hardware Diagnostics UEFI version ................. 84 Downloading Remote HP PC Hardware Diagnostics UEFI by product name or number ............................................................................................................................ 84 Customizing Remote HP PC Hardware Diagnostics UEFI settings .................................................... 84 10 Specifications ............................................................................................................................................ 85 Computer specifications ...................................................................................................................................... 85 39.6 cm (15.6 in) display specifications .............................................................................................................. 86 ix Solid-state drive specifications ........................................................................................................................... 86 11 Statement of memory volatility .................................................................................................................. 88 Current BIOS steps ............................................................................................................................................... 88 Nonvolatile memory usage ................................................................................................................................. 90 Questions and answers ....................................................................................................................................... 92 Using HP Sure Start (select products only) ......................................................................................................... 93 12 Power cord set requirements ...................................................................................................................... 94 Requirements for all countries ............................................................................................................................ 94 Requirements for specific countries and regions ................................................................................................ 94 13 Recycling .................................................................................................................................................. 96 Index ............................................................................................................................................................. 97 x 1 Product description This table provides detailed product information. Table 1-1 Product components and their descriptions Category Description Product Name HP EliteBook 850 G7 Notebook PC Processors 10th Generation Intel® CoreTM processors Intel Core i7-10810U (1.1 GHz [turbo up to 4.9 GHz], 6 cores, 12 MB L3 cache, 15 W) Intel Core i7-10710U (1.8 GHz [turbo up to 4.7 GHz], 6 cores, 12 MB L3 cache, 15 W) Intel Core i7-10610U (1.8 GHz [turbo up to 4.9 GHz], 4 cores, 8 MB L3 cache, 15 W) Intel Core i7-10510U (1.8 GHz [turbo up to 4.9 GHz], 4 cores, 8 MB L3 cache, 15 W) Intel Core i5-10310U (1.7 GHz [turbo up to 4.4 GHz], 4 cores, 6 MB L3 cache, 15 W) Intel Core i5-10210U (1.6 GHz [turbo up to 4.2 GHz], 4 cores, 6 MB L3 cache, 15 W) Graphics Internal graphics Intel UHD Graphics Premium Supports HD Decode, DX12, and HDMI 1.4b, HDCP 2.3 via DisplayPort up to 4 K @ 60 Hz and via HDMI up to 4 K @ 30 Hz External graphics NVIDIA® GeForce® MX250 Graphics Card 2 GB DDR5 VRAM Supports maximum of three independent displays when on the HP USB-C Dock G5: Max resolution = 1920 × 1200 @ 60 Hz and 1280 × 768 @ 60 Hz Supports maximum of three independent displays when on the HP USB-C/A Universal Dock G2; Max resolution = 2.5 K @ 60 Hz and 2.5 K @ 60 Hz Supports maximum of three independent displays when on the HP Thunderbolt Dock 120W G2; Max resolution = 2.5 K @ 60 Hz and 2.5 K @ 60 Hz Display 39.6 cm (15.6 in), narrow bezel, UWVA, antiglare, bent, supports privacy filter, nontouch Full high definition (FHD) (1920 × 1080), 250 nits, 45% CG, eDP, no camera FHD, 250 nits, 45% CG, eDP, HD camera FHD, 250 nits, 45% CG, eDP, HD + IR camera FHD, 250 nits, 45% CG, eDP, no camera, WWAN FHD, 250 nits, 45% CG, eDP, HD camera, WWAN FHD, 250 nits, 45% CG, eDP, HD + IR camera, WWAN FHD, 400 nits, sRGB 100%, eDP + PSR, low power, ambient light sensor, HD + IR camera FHD, 400 nits, sRGB 100%, eDP + PSR, low power, ambient light sensor, HD + IR camera, WWAN 1 Table 1-1 Product components and their descriptions (continued) Category Description Ultra high definition (UHD) (3840 × 2160), 400 nits, sRGB 100%, eDP + PSR, low power, ambient light sensor, HD + IR camera UHD, 400 nits, sRGB 100%, eDP + PSR, low power, ambient light sensor, HD + IR camera, WWAN FHD, 1000 nits, 72% CG, eDP + PSR, Sure View Reflect, ambient light sensor, HD camera FHD, 1000 nits, 72% CG, eDP + PSR, Sure View Reflect, ambient light sensor, HD camera, WWAN FHD, 1000 nits, 72% CG, eDP + PSR, Sure View Reflect, ambient light sensor, HD + IR camera FHD, 1000 nits, 72% CG, eDP + PSR, Sure View Reflect, ambient light sensor, HD + IR camera, WWAN 39.6 cm (15.6 in), full high definition (FHD) (1920 × 1080), UWVA, antiglare, bent, touch screen, 250 nits, touch screen FHD, 250 nits, HD + IR camera, Touch-on panel (TOP) FHD, 250 nits, HD + IR camera, WWAN, Touch-on panel (TOP) Memory Two customer-accessible memory module slots supporting up to 64 GB of RAM DDR4-2666 dual-channel support Supports the following configurations: 64 GB (32 × 2) 32 GB (16 × 2) 16 GB (8 × 2) or (16 × 1) 8 GB (8 × 1 or 4 × 2) 4 GB (4 × 1) Operating system recovery 32 GB eMMC (On-board embedded MultiMedia Controller) Primary storage M.2 2280 solid-state drives (NGFF) 1 TB, PCIe, Gen3 × 4, NVMe, SS, TLC 512 GB, PCIe, Gen3 × 2 × 2, SS QLC + 32 GB Intel OptaneTM memory 512 GB, PCIe, Gen3 × 4, NVMe, SS, TLC 512 GB, PCIe, Gen3 × 4, NVMe, SS, TLC (OPAL 2) 512 GB, PCIe, NVMe, SS, value 256 GB, PCIe, Gen3 × 2 × 2, SS QLC + 16 GB Intel Optane memory 256 GB, PCIe, Gen3 × 4, NVMe, SS, TLC 256 GB, PCIe, TLC (OPAL 2) 256, PCIe, NVMe, SS, value Audio and video HP Bang & Olufsen Audio Stereo speakers (2), 11 mm × 34 mm × 4 mm with 3× magnet speaker drivers Microphone (multi-array including rear-facing camera) Camera, HD RGB 720p 2 Chapter 1 Product description Table 1-1 Product components and their descriptions (continued) Category Description Camera, HD RGB 720p + IR (infrared) Camera privacy cover Supports WDR (Wide Dynamic Range) Support for models without a camera RJ-45 (network) jack No direct Ethernet support, available via accessories The following support S4/S5 wake on LAN (via out of band) and S0/S0ix/S4/S5 MPAT (via out of band): HP USB-C Mini Dock, HP USB-C/A Universal Dock G2, HP USB-C Dock G5, HP USB-C Dock G4 3, HP Thunderbolt Dock G2, and HP USB-C Mini Dock. Wireless Wireless Local Area Network (WLAN) (select products only) Intel Wi-Fi 6 AX201 + Bluetooth® 5 (802.11ax 2 × 2) (non-vPro) Intel Wi-Fi 6 AX201 + Bluetooth 5 (802.11ax 2 × 2) (vPro) Compatible with Miracast® devices Two WLAN antennas configured at top of panel Supports HP Connection Optimizer (with data analytics) UEFI Wi-Fi (Wireless imaging/image recovery/BitLocker unlock) Intel BT audio offload Supports Static BIOS SAR for Intel modules Supports HP Extended Range Wireless LAN Supports HP LAN-Wireless Protection (WLAN/LAN/WWAN switching) Near Field Communication (NFC) (select products only) NXP NPC300 Near Field Communication Module NFC antenna WWAN (select products only) Intel XMMTM 7360 LTE-Advanced (Cat 9) Intel XMM 7560 LTE-Advanced Pro (Cat 16) Four WWAN antennas (worldwide 5 band, 2 at top and 2 at bottom of WWAN panels) WWAN cards are compatible with a programmable removable eSIM Supports WWAN after market option Ports HDMI v1.4b Audio-out (headphone)/audio-in (microphone) combo jack (2) USB 3.1 Gen 1 Type-C® with ThunderboltTM USB 3.1 Gen 1 port USB 3.1 Gen 1 charging port AC Smart Pin adapter plug, 4.5 mm 3 Table 1-1 Product components and their descriptions (continued) Category Description Sensors Ambient light sensor (ALS) Hall sensor Keyboard/pointing devices HP Premium Keyboard (with numeric keypad) Backlit, spill resistant, HP Dura Keys Backlit, spill resistant, HP Dura Keys, privacy Not backlit, spill resistant, HP Dura Keys Not backlit, spill resistant, HP Dura Keys, privacy Touchpad Firmware PTP Microsoft® precision touchpad default gestures support No hybrid mode support Power requirements Battery 3 cell, 56 Whr, lithium polymer, HP Long Life HP Fast Charge Technology Smart AC adapters 65 W, right angle, 4.5 mm 65 W, right angle, 4.5 mm, for use in Argentina 65 W, right angle, 4.5 mm, EM 65 W, straight, USB Type-C® 65 W, slim, USB Type-C 45 W, right angle, 4.5 mm 45 W, right angle, 4.5 mm, for use in Argentina 45 W, right angle, 4.5 mm, 2 prong Power cord 3 wire, C5, 1.0 m, premium 3 wire, C5, 1.0 m conventional 2 wire, C7, 1.0 m, conventional Security Trusted Platform Module (TPM) 2.0, Infineon, soldered down Touch fingerprint sensor (select products only) Nano security lock Smart card reader (active) (select products only) Preboot authentication (password, smart card) SecureBIO capable 4 Chapter 1 Product description Table 1-1 Product components and their descriptions (continued) Category Description Hardware enforced firmware protection: HP Hardware Root of Trust + Sure Start Gen6 Operating system Windows® 10 Home 64 Windows 10 Home 64 Advanced Windows 10 Home 64 Advanced Single Language Windows 10 Home 64 Chinese Market CPPP Windows 10 Home 64 High-End Chinese Market CPPP Windows 10 Home 64 Plus Windows 10 Home 64 Plus Single Language Windows 10 Home 64 Plus Single Language Africa Market PPP Windows 10 Home 64 Plus Single Language APAC EM PPP Windows 10 Home 64 Plus Single Language India Market PPP Windows 10 Home 64 Plus Single Language Indonesia Market PPP Windows 10 Home 64 Single Language Windows 10 Home 64 Single Language Africa Market PPP Windows 10 Home 64 Single Language APAC Market PPP Windows 10 Home 64 Single Language India Market PPP Windows 10 Home 64 Single Language Indonesia Market PPP Windows 10 Pro 64 Windows 10 Pro 64 Chinese Market Windows 10 Pro 64 StF MSNA Plus Windows 10 Pro 64 StF MSNA Standard FreeDOS 3.0 Restore media Windows 10 Driver DVD Windows 10 Driver USB Windows 10 Professional 64 bit OS DVD Certified Microsoft WHQL Tested and documented Windows 10 Enterprise 64 LTSC 1809 (available only by request) Web-only support Windows 10 Enterprise 64 Serviceability End user replaceable parts 5 Table 1-1 Product components and their descriptions (continued) Category Description AC adapter Memory module Solid-state drive WLAN module WWAN module 6 Chapter 1 Product description 2 Components Your computer features top-rated components. This chapter provides details about your components, where they are located, and how they work. Right side Use the illustration and table to identify the components on the right side of the computer. Table 2-1 Right-side components and their descriptions Component Description (1) nano SIM card slot (select products only) Supports a wireless subscriber identity module (nano SIM) card. IMPORTANT: Inserting a SIM card of the wrong size could damage the SIM card or cause the SIM card to become stuck in the slot. To prevent damage to the SIM card or the connectors, use minimal force when inserting a SIM card. NOTE: Before purchasing a SIM card, follow these instructions to determine the correct SIM card size for your computer: 1. Go to http://www.hp.com/support, and then search for your computer by product name or number. 2. Select Product Information. 3. Refer to the listed options to determine which card to purchase. (2) USB Type-C power connector and ThunderboltTM Connect an AC adapter that has a USB Type-C connector, ports (2) with HP Sleep and Charge supplying power to the computer and, if needed, charging the computer battery. - and - Connect a USB device, provides high-speed data transfer, and charges small devices, even when the computer is off. - and - Connect a display device that has a USB Type-C connector, providing DisplayPortTM output. NOTE: Your computer might also support a Thunderbolt docking station. NOTE: Cables, adapters, or both (purchased separately) might be required. 7 Table 2-1 Right-side components and their descriptions (continued) Component Description (3) HDMI port Connects an optional video or audio device, such as a highdefinition television, any compatible digital or audio component, or a high-speed High-Definition Multimedia Interface (HDMI) device. (4) USB SuperSpeed port Connects a USB device, provides high-speed data transfer, and (for select products) charges small devices when the computer is on or in Sleep mode. (5) Battery light When AC power is connected: White: The battery charge is greater than 90%. Amber: The battery charge is from 0 to 90%. Off: The battery is not charging. When AC power is disconnected (battery not charging): Blinking amber: The battery has reached a low battery level. When the battery has reached a critical battery level, the battery light begins blinking rapidly. Off: The battery is not charging. (6) Power connector Connects an AC adapter. Left side Use the illustration and table to identify the components on the left side of the computer. Table 2-2 Left-side components and their descriptions Component Description (1) Security cable slot Attaches an optional security cable to the computer. NOTE: The security cable is designed to act as a deterrent, but it might not prevent the computer from being mishandled or stolen. (2) USB SuperSpeed port with HP Sleep and Charge Connects a USB device, provides high-speed data transfer, and charges small devices, even when the computer is off. (3) Audio-out (headphone)/Audio-in (microphone) Connects optional powered stereo speakers, headphones, combo jack earbuds, a headset, or a television audio cable. Also connects an optional headset microphone. This jack does not support optional standalone microphones. 8 Chapter 2 Components Table 2-2 Left-side components and their descriptions (continued) Component Description WARNING! To reduce the risk of personal injury, adjust the volume before putting on headphones, earbuds, or a headset. For additional safety information, see the Regulatory, Safety, and Environmental Notices. To access this guide: Type HP Documentation in the taskbar search box, and then select HP Documentation. NOTE: When a device is connected to the jack, the computer speakers are disabled. (4) Smart card reader Supports optional smart cards. Display The computer display can include essential components such as speakers, antennas, cameras, and microphones. Table 2-3 Display components and their descriptions Component (1) WWAN antennas* (select products only) (2) WLAN antennas* (select products only) (3) Camera light(s) (4) Ambient light sensor (select products only) Description Send and receive wireless signals to communicate with wireless wide area networks (WWANs). Send and receive wireless signals to communicate with wireless local area networks (WLANs). On: One or more cameras are in use. Adjusts the brightness of the display, depending on the ambient light. Display 9 Table 2-3 Display components and their descriptions (continued) Component Description (5) Internal microphones Record sound. (6) Camera (select products only) Allows you to video chat, record video, and record still images. Some cameras also allow a facial recognition logon to Windows, instead of a password logon. NOTE: Camera functions vary depending on the camera hardware and software installed on your product. (7) Camera privacy cover By default, the camera lens is uncovered, but you can slide the camera privacy cover to block the camera's view. To use the camera, slide the camera privacy cover in the opposite direction to reveal the lens. NOTE: If you have both front-facing and rear-facing cameras, when one camera lens is revealed and ready to use, the other is concealed. *The antennas are not visible from the outside of the computer. For optimal transmission, keep the areas immediately around the antennas free from obstructions. For wireless regulatory notices, see the section of the Regulatory, Safety, and Environmental Notices that applies to your country or region. To access this guide: Type HP Documentation in the taskbar search box, and then select HP Documentation. Keyboard area Keyboards can vary by language. Touchpad components Use the illustration and table to identify the touchpad components. To adjust touchpad settings and gestures, or to turn off the touchpad: 1. Type touchpad settings in the taskbar search box, and then press enter. 2. Choose a setting. To turn on the touchpad: 1. Type touchpad settings in the taskbar search box, and then press enter. 2. Using an external mouse, click the touchpad button. - or Press the Tab key repeatedly until the pointer rests on the touchpad button. Then press the spacebar to select the button. 10 Chapter 2 Components Table 2-4 Touchpad components and their descriptions Component Description (1) Pointing stick Moves the pointer on the screen. (2) Left pointing stick button Functions like the left button on an external mouse (3) Right pointing stick button Functions like the right button on an external mouse (4) Touchpad zone Reads your finger gestures to move the pointer or activate items on the screen. (5) Near Field Communications (NFC) tapping area Allows you to wirelessly share information when you tap it with and antenna (select products only) an NFC-enabled device. Lights Use the illustration and table to identify the lights on the computer. Keyboard area 11 Table 2-5 Lights and their descriptions Component (1) Caps lock light (2) Fn lock light (3) Privacy key light (select products only) (4) Mute light (5) Microphone mute light (6) Power light (7) Num lk light Description On: Caps lock is on, which switches the key input to all capital letters. On: The fn key is locked. On: Privacy screen is on, which helps prevent side-angle viewing. On: Computer sound is off. Off: Computer sound is on. On: The microphone is off. Off: The microphone is on. On: The computer is on. Blinking (select products only): The computer is in the Sleep state, a power-saving state. The computer shuts off power to the display and other unnecessary components. Off: Depending on your computer model, the computer is off, in Hibernation, or in Sleep. Hibernation is the powersaving state that uses the least amount of power. On: Num lock is on. Button, speakers, and fingerprint reader Identify the computer button, speakers, and fingerprint reader. Fingerprint readers can be located on the touchpad, on a side panel of the computer, or on the top cover below the keyboard. 12 Chapter 2 Components IMPORTANT: To verify that your computer supports fingerprint reader sign-in, type Sign-in options in the taskbar search box and follow the on-screen instructions. If Fingerprint reader is not listed as an option, then your notebook does not include a fingerprint reader. Table 2-6 Button, speakers, and fingerprint reader and their descriptions Component Description (1) Speakers (2) Produce sound (2) Vents (2) Enable airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. (3) Power button When the computer is off, press the button briefly to turn on the computer. When the computer is on, press the button briefly to initiate Sleep. When the computer is in the Sleep state, press the button briefly to exit Sleep (select products only). When the computer is in Hibernation, press the button briefly to exit Hibernation. IMPORTANT: Pressing and holding down the power button results in the loss of unsaved information. If the computer has stopped responding and shutdown procedures are ineffective, press and hold the power button down for at least 4 seconds to turn off the computer. To learn more about your power settings, see your power options: Keyboard area 13 Table 2-6 Button, speakers, and fingerprint reader and their descriptions (continued) Component Description Right-click the Power icon, and then select Power Options. (4) Fingerprint reader (select products only) Allows a fingerprint logon to Windows, instead of a password logon. Swipe down across the fingerprint reader. IMPORTANT: To prevent fingerprint logon issues, be sure when you register your fingerprint that all sides of your finger are registered by the fingerprint reader. Special keys Use the illustration and table to identify the special keys. Table 2-7 Special keys and their descriptions Component (1) esc key (2) fn key (3) Windows key (4) Action keys (5) Programmable key (6) Power button 14 Chapter 2 Components Description Displays system information when pressed in combination with the fn key. Executes frequently used system functions when pressed in combination with another key. Such key combinations are called hot keys. Opens the Start menu. NOTE: Pressing the Windows key again will close the Start menu. Execute frequently used system functions. Executes frequently used tasks. Some tasks might not be available on all products. When the computer is off, press the button briefly to turn on the computer. Table 2-7 Special keys and their descriptions (continued) Component (7) num lk key (8) Integrated numeric keypad Description When the computer is on, press the button briefly to initiate Sleep. When the computer is in the Sleep state, press the button briefly to exit Sleep (select products only). When the computer is in Hibernation, press the button briefly to exit Hibernation. IMPORTANT: Pressing and holding down the power button results in the loss of unsaved information. If the computer has stopped responding and shutdown procedures are ineffective, press and hold the power button down for at least 4 seconds to turn off the computer. To learn more about your power settings, see your power options: Right-click the Power icon, and then select Power Options. Alternates between the navigational and numeric functions on the integrated numeric keypad. A separate keypad to the right of the alphabet keyboard. When num lk is pressed, the integrated keypad can be used like an external numeric keypad. NOTE: If the keypad function is active when the computer is turned off, that function is reinstated when the computer is turned back on. Hot keys (select products only) A hot key is the combination of the fn key and another key. Use the table to identify the hot keys. To use a hot key: Press the fn key, and then press one of the keys listed in the following table. Table 2-8 Hot keys and their descriptions Key Description C Turns on scroll lock. E Turns on the insert function. R Breaks the operation. S Sends a programing query. W Pauses the operation. Bottom Use the illustration and table to identify the bottom component. Bottom 15 Table 2-9 Bottom component and its description Component Description Vent Enables airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. Labels The labels affixed to the computer provide information that you might need when you troubleshoot system problems or travel internationally with the computer. Labels can be in paper form or imprinted on the product. IMPORTANT: Check the following locations for the labels described in this section: the bottom of the computer, inside the battery bay, under the service door, on the back of the display, or on the bottom of a tablet kickstand. Service label--Provides important information to identify your computer. When contacting support, you might be asked for the serial number, the product number, or the model number. Locate this information before you contact support. Your service label information order may vary by country and might not include the wording "Model" due to the country regulation. 16 Chapter 2 Components Table 2-10 Service label components Component (1) HP product name (2) Product ID (3) Serial number (4) Warranty period Regulatory label(s)--Provide(s) regulatory information about the computer. Wireless certification label(s)--Provide(s) information about optional wireless devices and the approval markings for the countries or regions in which the devices have been approved for use. Labels 17 3 Illustrated parts catalog Use this table to determine the spare parts that are available for the computer. Computer major components To identify the computer major components, use this illustration and table. NOTE: HP continually improves and changes product parts. For complete and current information about supported parts for your computer, go to http://partsurfer.hp.com, select your country or region, and then follow the on-screen instructions. NOTE: Details about your computer, including model, serial number, product key, and length of warranty, are on the service tag at the bottom of your computer. 18 Chapter 3 Illustrated parts catalog Table 3-1 Computer major component descriptions and part numbers Item Component (1) Display assembly NOTE: Display spare parts are available only as subcomponents. For spare part information, see Display assembly subcomponents on page 21. (2) Top cover/keyboard NOTE: For a detailed list of country codes, see Keyboard with top cover on page 72. Backlit Not backlit Backlit, for use in privacy models (3) Touchpad Without NFC antenna Includes NFC antenna (4) Touchpad button board (5) Fingerprint reader NOTE: The fingerprint reader cable is available in the Cable Kit as spare part number M05255-001. (6) RTC battery (7) NFC module NOTE: The NFC module cable is available in the Cable Kit as spare part number M05255-001. (8) Speakers (left and right) (9) System board (includes integrated processor) NOTE: All system board spare part kits include replacement thermal material. All system boards use the following part numbers: xxxxxx-001: Non-Windows operating systems xxxxxx-601: Windows operating system Models with discrete graphics memory: Intel Core i7-10810 processor (OSR) Intel Core i7-10710 processor Intel Core i7-10610 processor Intel Core i7-10610 processor (OSR) Intel Core i7-10510 processor Intel Core i5-10310 processor Intel Core i5-10210 processor For use in models with UMA graphics memory: Intel Core i7-10810 processor (OSR) Intel Core i7-10710 processor Spare part number not available as a spare part M07491-xx1 M07493-xx1 M07492-xx1 M05269-001 M05270-001 M05267-001 M07206-001 L17255-001 M07214-001 M05268-001 M05245-xx1 M14257-xx1 M05243-xx1 M05244-xx1 M05241-xx1 M05242-xx1 M05240-xx1 M05252-xx1 M14258-xx1 Computer major components 19 Table 3-1 Computer major component descriptions and part numbers (continued) Item Component Intel Core i7-10610 processor Intel Core i7-10610 processor (OSR) Intel Core i5-10210 processor Intel Core i5-10310 processor Intel Core i5-10310 processor (OSR) Intel Core i5-10210 processor (10) Card reader board NOTE: The card reader board cable is available in the Cable Kit as spare part number M05255-001. (11) USB board NOTE: The USB board cable is available in the Cable Kit as spare part number M05255-001. (12) Power connector cable (13) System board bracket (available in Plastics Kit) (14) Fan Heat sink (includes replacement thermal material) (15) For use in models with UMA graphics memory (16) For use in models with discrete graphics memory (17) WLAN module Intel Wi-Fi 6 AX201 + Bluetooth 5 (802.11ax 2 × 2, vPro) Intel Wi-Fi 6 AX201 + Bluetooth 5 (802.11ax 2 × 2, non-vPro) (18) Memory modules (DDR4, PC-2666) 32 GB 16 GB 8 GB 4 GB (19) Memory cover (included in Bracket Kit) (20) WWAN module Intel XMM 7560 LTE-Advanced Pro (Cat16) Intel XMM 7360 LTE-Advanced (Cat 9) (21) Solid-state drive 1 TB, PCIe, TLC 512 GB, PCIe, TLC 512 GB, PCIe, TLC, self-encrypting drive (SED) 512 GB, PCIe, value Spare part number M05250-xx1 M05251-xx1 M05247-xx1 M05248-xx1 M05249-xx1 M05246-xx1 M07105-001 M05266-001 M15626-001 M16739-001 M05261-001 M05262-001 M05263-001 L57248-002 L57250-002 L50384-002 937438-852 937236-852 L10598-852 M05264-001 L40752-002 L70670-002 L85348-002 L85360-002 L85368-002 L85364-002 20 Chapter 3 Illustrated parts catalog Table 3-1 Computer major component descriptions and part numbers (continued) Item Component 512 GB, PCIe + 32 GB Optane memory 256 GB, PCIe, value 256 GB, PCIe + 16 GB Optane memory 128 GB, SATA-3, TLC (22) Battery (3 cell, 56 Whr) (23) Bottom cover For use in models with discrete graphics memory For use in models with UMA graphics memory Display assembly subcomponents To identify the display assembly subcomponents, use this illustration and table. Spare part number L85366-002 L85354-002 L85356-002 L85346-002 L77991-005 M05253-001 M14249-001 Table 3-2 Display component descriptions and part numbers Item Component (1) Display bezel For use in models with an IR camera and ambient light sensor For use in models with an IR camera For use in models with an RGB camera and ambient light sensor For use in models with an RGB camera For use in models with a microphone module (no camera) Spare part number M05256-001 M05257-001 M05258-001 M05259-001 M05260-001 Display assembly subcomponents 21 Table 3-2 Display component descriptions and part numbers (continued) Item Component (2) Display panel Privacy 250 nits, nontouch 250 nits, Touch-on Panel (TOP) 400 nits, FHD 400 nits, UHD (3) Hinge cover (included in Hinge Kit) (4) Camera module RGB camera IR camera (5) Camera cable (included in Cable Kit) (6) WLAN antennas and cables (7) WWAN antennas and cables (8) Ambient light sensor (9) Ambient light sensor board to hub board cable (included in Cable Kit) (10) Microphone module Third microphone module (11) Microphone board cable (included in Cable Kit) (12) Hub board For use in models with an RGB camera or microphone module For use in models with an IR camera (13) Display cable (included in Display Cable Kit) (14) Display cable (included in Display Cable Kit) (15) Hinges (left and right) (16) Display back cover Models with 250 nit, Touch-on Panel (TOP) Models with 400 nit, FHD panel, and no WWAN Models with 400 nit, FHD panel, and WWAN Models with 400 nit, UHD panel, and no WWAN Second ambient light sensor (not illustrated) Second ambient light sensor to display panel cable (included in Cable Kit; not illustrated) Second ambient light sensor to hub board cable (included in Cable Kit; not illustrated) Spare part number M14367-001 M05236-001 M05237-001 M05238-001 M05239-001 M05265-001 M07216-001 M08549-001 M05255-001 M07212-001 M05255-001 M07208-001 M07209-001 M05255-001 M07210-001 M07211-001 M07203-001 M05513-001 M05265-001 M05254-001 M14250-001 M14251-001 M14252-001 M07213-001 M05255-001 M05255-001 22 Chapter 3 Illustrated parts catalog Bracket Kit To identify the Bracket Kit components, use this illustration and table. Table 3-3 Bracket Kit component descriptions and part numbers Item Component Bracket Kit, includes: (1) Memory cover (2) Left USB bracket (3) Right USB bracket (4) Fingerprint reader bracket SIM tray (not illustrated) Plastics Kit To identify the Plastics Kit components, use this illustration and table. Spare part number M05264-001 Bracket Kit 23 Table 3-4 Plastics Kit component descriptions and part numbers Item Component Plastics Kit, includes: (1) I/O frame (2) Fingerprint reader insert (3) SIM card insert (4) Smart card reader insert WWAN insulator (not illustrated) Cable Kit To identify the contents of the Cable Kit, use this table. Table 3-5 Cable Kit content descriptions and part number Component Cable Kit, includes: Ambient light sensor to hub board cable Third microphone board to hub board cable Camera/microphone module to hub board cable Touchpad cable Fingerprint reader board cable NFC module to system board cable Smart card reader to system board cable USB board to system board cable IR camera to hub board cable Hub board to system board cable Miscellaneous parts To identify the miscellaneous parts, use this table. Table 3-6 Miscellaneous part descriptions and part numbers Component AC adapters 65 W, nPFC, SMART, 3 pin, 4.5 mm 65 W, nPFC, SMART, 4.5 mm, EM 65 W, nPFC, USB-C, straight, 1.8 m 65 W, nPFC, USB-C, 1.8 m 24 Chapter 3 Illustrated parts catalog Spare part number M16739-001 Spare part number M05255-001 Spare part number 710412-001 913691-850 L04650-850 L67440-001 Table 3-6 Miscellaneous part descriptions and part numbers (continued) Component 45 W, nPFC, SMART, RC, 4.5 mm, nonslim 45 W, nPFC, SMART, RC, 4.5 mm, 2 pin Screw Kit Power adapter, duckhead, C5NS South Korea North America Power cord (C7, conventional, 1.0 m) Japan Power cord (C5, conventional, 1.0 m) Argentina Australia Brazil Denmark Europe (Austria, Belgium, Finland, France, Germany, the Netherlands, Norway, and Sweden) India Israel Italy Japan North America People's Republic of China South Africa South Korea Switzerland Taiwan Thailand The United Kingdom Power cord (C5, 1.0 m, premium) Argentina Australia Brazil Denmark Europe (Austria, Belgium, Finland, France, Germany, the Netherlands, Norway, and Sweden) India Spare part number 741727-001 742436-001 M14238-001 L50818-001 L50818-002 L19375-001 L19357-001 L19358-001 L19359-001 L19360-001 L19361-001 L19363-001 L19362-001 L19364-001 L19365-001 L19367-001 L19368-001 L19369-001 L19366-001 L19370-001 L19372-001 L19371-001 L19373-001 L30811-001 L22327-001 L30812-001 L22322-001 L22321-001 L22624-001 Miscellaneous parts 25 Table 3-6 Miscellaneous part descriptions and part numbers (continued) Component Israel Italy Japan North America People's Republic of China South Africa South Korea Switzerland Taiwan Thailand United Kingdom Spare part number L22323-001 L30813-001 L22330-001 L22319-001 L21930-001 L22325-001 L22328-001 L22324-001 L22329-001 L22326-001 L22320-001 26 Chapter 3 Illustrated parts catalog 4 Removal and replacement procedures preliminary requirements Use this information to properly prepare to disassemble and reassemble the computer. Tools required You need the following tools to complete the removal and replacement procedures: Tweezers Nonconductive, nonmarking pry tool Magnetic Phillips P1 screwdriver Service considerations The following sections include some of the considerations that you must keep in mind during disassembly and assembly procedures. NOTE: As you remove each subassembly from the computer, place the subassembly (and all accompanying screws) away from the work area to prevent damage. Plastic parts Using excessive force during disassembly and reassembly can damage plastic parts. Cables and connectors Handle cables with extreme care to avoid damage. IMPORTANT: When servicing the computer, be sure that cables are placed in their proper locations during the reassembly process. Improper cable placement can damage the computer. Apply only the tension required to unseat or seat the cables during removal and insertion. Handle cables by the connector whenever possible. In all cases, avoid bending, twisting, or tearing cables. Be sure that cables are routed so that they cannot be caught or snagged as you remove or replace parts. Handle flex cables with extreme care; these cables tear easily. Drive handling Note the following guidelines when handling drives. Tools required 27 IMPORTANT: Drives are fragile components. Handle them with care. To prevent damage to the computer, damage to a drive, or loss of information, observe these precautions: Before removing or inserting a hard drive, shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. Before handling a drive, be sure that you are discharged of static electricity. While handling a drive, avoid touching the connector. Before removing an optical drive, be sure that a disc is not in the drive, and be sure that the optical drive tray is closed. Handle drives on surfaces covered with at least 2.54 cm (1 inch) of shock-proof foam. Avoid dropping drives from any height onto any surface. After removing a hard drive or an optical drive, place it in a static-proof bag. Avoid exposing an internal hard drive to products that have magnetic fields, such as monitors or speakers. Avoid exposing a drive to temperature extremes or liquids. If a drive must be mailed, place the drive in a bubble pack mailer or other suitable form of protective packaging, and label the package "FRAGILE." Workstation guidelines Follow these grounding workstation guidelines: Cover the workstation with approved static-shielding material. Use a wrist strap connected to a properly grounded work surface and use properly grounded tools and equipment. Use conductive field service tools, such as cutters, screw drivers, and vacuums. When fixtures must directly contact dissipative surfaces, use fixtures made only of static-safe materials. Keep the work area free of nonconductive materials, such as ordinary plastic assembly aids and polystyrene foam. Handle ESD-sensitive components, parts, and assemblies by the case or PCM laminate. Handle these items only at static-free workstations. Avoid contact with pins, leads, or circuitry. Turn off power and input signals before inserting or removing connectors or test equipment. Electrostatic discharge information A sudden discharge of static electricity from your finger or other conductor can destroy static-sensitive devices or microcircuitry. Often the spark is neither felt nor heard, but damage occurs. An electronic device exposed to electrostatic discharge (ESD) might not appear to be affected at all and can work perfectly throughout a normal cycle. The device might function normally for a while, but it has been degraded in the internal layers, reducing its life expectancy. Networks built into many integrated circuits provide some protection, but in many cases, the discharge contains enough power to alter device parameters or melt silicon junctions. 28 Chapter 4 Removal and replacement procedures preliminary requirements IMPORTANT: To prevent damage to the device when you remove or install internal components, observe these precautions: Keep components in their electrostatic-safe containers until you are ready to install them. Before touching an electronic component, discharge static electricity by using the guidelines described Personal grounding methods and equipment on page 30. Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible. If you remove a component, place it in an electrostatic-safe container. Generating static electricity Follow these static electricity guidelines. Different activities generate different amounts of static electricity. Static electricity increases as humidity decreases. Table 4-1 Static electricity occurrence based on activity and humidity Relative humidity Event 55% 40% Walking across carpet Walking across vinyl floor Motions of bench worker Removing DIPs (dual in-line packages) from plastic tube 7,500 V 3,000 V 400 V 400 V 15,000 V 5,000 V 800 V 700 V Removing DIPs from vinyl tray Removing DIPs from polystyrene foam Removing bubble pack from PCB (printed circuit board) Packing PCBs in foam-lined box 2,000 V 3,500 V 7,000 V 5,000 V 4,000 V 5,000 V 20,000 V 11,000 V Multiple electric components can be packaged together in plastic tubes, trays, or polystyrene foam. 10% 35,000 V 12,000 V 6,000 V 2,000 V 11,500 V 14,500 V 26,500 V 21,000 V NOTE: As little as 700 V can degrade a product. Preventing electrostatic damage to equipment Many electronic components are sensitive to ESD. Circuitry design and structure determine the degree of sensitivity. The following packaging and grounding precautions are necessary to prevent static electricity damage to electronic components. To avoid hand contact, transport products in static-safe containers such as tubes, bags, or boxes. Protect all electrostatic parts and assemblies with conductive or approved containers or packaging. Keep electrostatic-sensitive parts in their containers until they arrive at static-free stations. Place items on a grounded surface before removing them from their container. Always be properly grounded when touching a sensitive component or assembly. Electrostatic discharge information 29 Avoid contact with pins, leads, or circuitry. Place reusable electrostatic-sensitive parts from assemblies in protective packaging or conductive foam. Personal grounding methods and equipment Using certain equipment can prevent static electricity damage to electronic components. Wrist straps are flexible straps with a maximum of 1 M ±10% resistance in the ground cords. To provide proper ground, a strap must be worn snug against bare skin. The ground cord must be connected and fit snugly into the banana plug connector on the grounding mat or workstation. Heel straps/Toe straps/Boot straps can be used at standing workstations and are compatible with most types of shoes or boots. On conductive floors or dissipative floor mats, use them on both feet with a maximum of 1 M ±10% resistance between the operator and ground. Table 4-2 Static shielding protection levels Static shielding protection levels Method Antistatic plastic Carbon-loaded plastic Metallized laminate Voltage 1,500 7,500 15,000 Grounding the work area To prevent static damage at the work area, follow these precautions. Cover the work surface with approved static-dissipative material. Provide a wrist strap connected to the work surface and properly grounded tools and equipment. Use static-dissipative mats, foot straps, or air ionizers to give added protection. Handle electrostatic sensitive components, parts, and assemblies by the case or PCB laminate. Handle them only at static-free work areas. Turn off power and input signals before inserting and removing connectors or test equipment. Use fixtures made of static-safe materials when fixtures must directly contact dissipative surfaces. Keep work area free of nonconductive materials such as ordinary plastic assembly aids and polystyrene foam. Use field service tools, such as cutters, screwdrivers, and vacuums, that are conductive. Recommended materials and equipment HP recommends certain materials and equipment to prevent static electricity. Antistatic tape Antistatic smocks, aprons, or sleeve protectors Conductive bins and other assembly or soldering aids Conductive foam Conductive tabletop workstations with ground cord of 1 M ±10% resistance 30 Chapter 4 Removal and replacement procedures preliminary requirements Static-dissipative table or floor mats with hard tie to ground Field service kits Static awareness labels Wrist straps and footwear straps providing 1 M ±10% resistance Material handling packages Conductive plastic bags Conductive plastic tubes Conductive tote boxes Opaque shielding bags Transparent metallized shielding bags Transparent shielding tubes Packaging and transporting guidelines Follow these grounding guidelines when packaging and transporting equipment. To avoid hand contact, transport products in static-safe tubes, bags, or boxes. Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging. Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations. Place items on a grounded surface before removing items from their containers. Always be properly grounded when touching a component or assembly. Store reusable ESD-sensitive parts from assemblies in protective packaging or nonconductive foam. Use transporters and conveyors made of antistatic belts and roller bushings. Be sure that mechanized equipment used for moving materials is wired to ground and that proper materials are selected to avoid static charging. When grounding is not possible, use an ionizer to dissipate electric charges. Packaging and transporting guidelines 31 5 Removal and replacement procedures for Customer Self-Repair parts This chapter provides removal and replacement procedures for Customer Self-Repair parts. NOTE: The Customer Self-Repair program is not available in all locations. Installing a part that is not supported by the Customer Self-Repair program can void your warranty. Check your warranty to determine whether Customer Self-Repair is supported in your location. Component replacement procedures To remove and replace computer components, use these procedures. NOTE: Details about your computer, including model, serial number, product key, and length of warranty, are on the service tag at the bottom of your computer. NOTE: HP continually improves and changes product parts. For complete and current information about supported parts for your computer, go to http://partsurfer.hp.com, select your country or region, and then follow the on-screen instructions. You must remove, replace, or loosen as many as 8 screws when you service Customer Self-Repair parts. Make special note of each screw size and location during removal and replacement. Preparation for disassembly To prepare to disassemble the computer, use these steps. See Removal and replacement procedures preliminary requirements on page 27 for initial safety procedures. 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. Bottom cover To remove the bottom cover, use this procedure and illustration. Table 5-1 Bottom cover description and part number Description Bottom cover for use in models with discrete graphics memory Bottom cover for use in models with UMA graphics memory Spare part number M05253-001 M14249-001 Before removing the bottom cover, prepare the computer for disassembly (Preparation for disassembly on page 32). Remove the bottom cover: 32 Chapter 5 Removal and replacement procedures for Customer Self-Repair parts 1. Loosen the five captive Phillips screws that secure the bottom cover to the computer. 2. Starting near the hinges, use a nonmarking, nonconductive tool to release the edges of the bottom cover from the computer (1). 3. Remove the bottom cover from the computer (2). To replace the bottom cover, reverse the removal procedures. Memory modules To remove the memory modules, use this procedure and illustration. Table 5-2 Memory module descriptions and part numbers Description 32 GB, DDR4-2666 16 GB, DDR4-2666 8 GB, DDR4-2666 4 GB, DDR4-2666 Memory module cover (included in Bracket Kit) Spare part number L50384-002 937438-852 937236-852 L10598-852 M05264-001 Component replacement procedures 33 Before removing the memory, follow these steps: 1. Prepare the computer for disassembly (Preparation for disassembly on page 32). 2. Remove the bottom cover (Bottom cover on page 32). 3. Disconnect the battery cable from the system board (see Battery on page 41). If you are replacing a memory module, remove the existing memory module: 1. Use the tab (1) to lift the cover off the memory modules (2). The cover is held in place by clips on the system board. 34 Chapter 5 Removal and replacement procedures for Customer Self-Repair parts 2. Spread the two retention clips outward (1) until the memory module tilts up at a 45° angle, and then remove the module (2). Use the same procedure to remove all memory modules. IMPORTANT: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module. To protect a memory module after removal, place it in an electrostatic-safe container. To install a memory module: 1. Align the notched edge of the module with the tab in the slot (1), and then press the module into the slot at an angle until it is seated (2). 2. Press down on the module until the side retention clips snap into place (3). Component replacement procedures 35 3. Replace the cover by inserting the edges of the cover into the clips on the system board that surround the memory modules (1). WLAN module To remove the WLAN module, use this procedure and illustration. Table 5-3 WLAN module descriptions and part numbers Description Intel Wi-Fi 6 AX201 + Bluetooth 5 (802.11ax 2 × 2, vPro) Intel Wi-Fi 6 AX201 + Bluetooth 5 (802.11ax 2 × 2, non-vPro) Spare part number L57248-002 L57250-002 IMPORTANT: To prevent an unresponsive system, replace the wireless module only with a wireless module authorized for use in the computer by the governmental agency that regulates wireless devices in your country or region. If you replace the module and then receive a warning message, remove the module to restore device functionality, and then contact technical support. Before removing the WLAN module, follow these steps: 1. Prepare the computer for disassembly (Preparation for disassembly on page 32). 2. Remove the bottom cover (Bottom cover on page 32). 3. Disconnect the battery cable from the system board (see Battery on page 41). Remove the WLAN module: 1. Carefully disconnect the two antenna cables from the module (1). 36 Chapter 5 Removal and replacement procedures for Customer Self-Repair parts 2. Remove the Phillips M2.0 × 2.5 screw (2), and then remove the WLAN module (3). NOTE: Models have either one or two WLAN antennas. On models with two antennas, the #1 white WLAN antenna cable connects to the WLAN module #1 Main terminal. The #2 black WLAN antenna cable connects to the WLAN module #1 Aux terminal. 3. If the WLAN antenna is not connected to the terminal on the WLAN module, install a protective sleeve on the antenna connector, as shown in the following illustration. Reverse this procedure to install the WLAN module. Component replacement procedures 37 WWAN module To remove the WWAN module, use this procedure and illustration. Table 5-4 WWAN module descriptions and part numbers Description Intel XMM 7560 LTE-Advanced Pro (Cat16) Intel XMM 7360 LTE-Advanced (Cat 9) Spare part number L40752-002 L70670-002 IMPORTANT: To prevent an unresponsive system, replace the wireless module only with a wireless module authorized for use in the computer by the governmental agency that regulates wireless devices in your country or region. If you replace the module and then receive a warning message, remove the module to restore device functionality, and then contact technical support. Before removing the WWAN module, follow these steps: 1. Prepare the computer for disassembly (Preparation for disassembly on page 32). 2. Remove the bottom cover (Bottom cover on page 32). 3. Disconnect the battery cable from the system board (see Battery on page 41). Remove the WWAN module: 1. Disconnect the WWAN antenna cables (1) from the terminals on the WWAN module. 2. Remove the Phillips M2.0 × 2.0 screw (2) that secures the WWAN module to the bottom cover. (The WWAN module tilts up.) 38 Chapter 5 Removal and replacement procedures for Customer Self-Repair parts 3. Remove the WWAN module (3) by pulling the module away from the slot at an angle. NOTE: When viewed with the antenna terminals at the top of the module, the white WWAN antenna cables connects to the terminal to the left of the black WWAN antenna cables. 4. If the WWAN antenna is not connected to the terminal on the WWAN module, a protective sleeve must be installed on the antenna connector, as shown in the following illustration. Reverse this procedure to install the WWAN module. Component replacement procedures 39 Solid-state drive To remove the M.2 solid-state drive, use this procedure and illustration. Table 5-5 Solid-state drive descriptions and part numbers Description 1 TB, PCIe, TLC 512 GB, PCIe, TLC 512 GB, PCIe, TLC, self-encrypting drive (SED) 512 GB, PCIe, value 512 GB, PCIe + 32 GB Optane memory 256 GB, PCIe, value 256 GB, PCIe + 16 GB Optane memory 128 GB, SATA-3, TLC Spare part number L85348-002 L85360-002 L85368-002 L85364-002 L85366-002 L85354-002 L85356-002 L85346-002 Before removing the solid-state drive, follow these steps: 1. Prepare the computer for disassembly (Preparation for disassembly on page 32). 2. Remove the bottom cover (Bottom cover on page 32). 3. Disconnect the battery cable from the system board (see Battery on page 41). Remove the solid-state drive: 1. Remove the Phillips M2.0 × 2.5 screw (1) that secures the drive to the computer. 2. Pull the drive away from the socket to remove it (2). To install the solid-state drive, reverse the removal procedures. NOTE: Solid-state drives are designed with a notch to prevent incorrect insertion. 40 Chapter 5 Removal and replacement procedures for Customer Self-Repair parts 6 Removal and replacement procedures for authorized service provider parts This chapter provides removal and replacement procedures for authorized service provider parts. IMPORTANT: Components described in this chapter should be accessed only by an authorized service provider. Accessing these parts can damage the computer or void the warranty. NOTE: Details about your computer, including model, serial number, product key, and length of warranty, are on the service tag at the bottom of your computer. Component replacement procedures To remove and replace computer components, use these procedures. NOTE: HP continually improves and changes product parts. For complete and current information about supported parts for your computer, go to http://partsurfer.hp.com, select your country or region, and then follow the on-screen instructions. You must remove, replace, or loosen as many as 50 screws when you service the parts described in this chapter. Make special note of each screw size and location during removal and replacement. Preparation for disassembly To remove and replace computer components, use these procedures. See Removal and replacement procedures preliminary requirements on page 27 for initial safety procedures. 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. Battery To remove the battery, use this procedure and illustration. Table 6-1 Battery description and part number Description Spare part number Battery, 3 cell, 56 Whr L77991-005 41 WARNING! To avoid personal injury and damage to the product: Do not puncture, twist, or crack the battery. Do not cause an external puncture or rupture to the battery. They can cause a short inside the battery, which can result in battery thermal runaway. Do not handle or touch the battery enclosure with sharp objects such as tweezers or pliers, which might puncture the battery. Do not compress or squeeze the battery case with tools or heavy objects stacked on top of the case. These actions can apply undue force on the battery. Do not touch the connectors with any metallic surface or object, such as metal tools, screws, or coins, which can cause shorting across the connectors. Before removing the battery, follow these steps: 1. Prepare the computer for disassembly (Preparation for disassembly on page 32). 2. Remove the bottom cover (Bottom cover on page 32). WARNING! To reduce potential safety issues, use only the user-replaceable battery provided with the computer, a replacement battery provided by HP, or a compatible battery purchased from HP. IMPORTANT: Removing a battery that is the sole power source for the computer can cause loss of information. To prevent loss of information, save your work or shut down the computer through Windows before you remove the battery. Remove the battery: 1. Disconnect the battery cable from the system board (1). 2. Remove the four Phillips M2.0 × 4.0 screws (2) that secure the battery to the computer. 3. Remove the battery from the computer (3). To insert the battery, reverse the removal procedures. 42 Chapter 6 Removal and replacement procedures for authorized service provider parts RTC battery To remove the RTC battery, use this procedure and illustration. Table 6-2 RTC battery description and part number Description RTC battery Spare part number L17255-001 Before removing the RTC battery, follow these steps: 1. Prepare the computer for disassembly (Preparation for disassembly on page 32). 2. Remove the bottom cover (Bottom cover on page 32). 3. Disconnect the battery cable from the system board (see Battery on page 41). 4. Remove the solid-state drive to the left of the battery (Solid-state drive on page 40). Remove the RTC battery: 1. Disconnect the battery cable from the system board (1). 2. Use a tool (2) to release the battery from the computer (3). Reverse this procedure to install the RTC battery. Card reader board To remove the card reader board, use this procedure and illustration. Table 6-3 Card reader board description and part number Description Card reader board Card reader board cable (included in Cable Kit) Spare part number M07105-001 M05255-001 Before removing the card reader board, follow these steps: Component replacement procedures 43 1. Prepare the computer for disassembly (Preparation for disassembly on page 32). 2. Remove the bottom cover (Bottom cover on page 32). 3. Remove the battery (see Battery on page 41). Remove the card reader board: 1. Disconnect the cable from the reverse ZIF connector on the card reader board (1). 2. Peel the cable off the card reader board (2). 3. Remove the three Phillips M2.0 × 2.0 screws (3) that secure the board to the computer. 4. Remove the board from the computer (4). Reverse this procedure to install the card reader board. Power connector cable To remove the power connector cable, use this procedure and illustration. Table 6-4 Power connector cable description and part number Description Power connector cable Spare part number M15626-001 Before removing the power connector cable, follow these steps: 1. Prepare the computer for disassembly (Preparation for disassembly on page 32). 2. Remove the bottom cover (Bottom cover on page 32). 3. Disconnect the battery cable from the system board (see Battery on page 41). Remove the power connector cable: 1. Disconnect the cable from the system board (1), and then remove the cable from the clip (2). 2. Remove the Phillips M2.0 × 4.0 screw (3) that secures the power connector cable to the computer. 44 Chapter 6 Removal and replacement procedures for authorized service provider parts 3. Remove the power connector cable from the computer (4). Reverse this procedure to install the power connector cable. USB board To remove the USB board, use this procedure and illustration. Table 6-5 USB board description and part number Description USB board USB board cable (included in Cable Kit) USB bracket (included in Bracket Kit) Spare part number M05266-001 M05255-001 M05264-001 Before removing the USB board, follow these steps: 1. Prepare the computer for disassembly (Preparation for disassembly on page 32). 2. Remove the bottom cover (Bottom cover on page 32). 3. Disconnect the battery cable from the system board (see Battery on page 41). Remove the USB board: 1. Disconnect the cable from the ZIF connector on the USB board (1). 2. Remove the three Phillips M2.0 × 4.0 screws (2) that secure the board to the computer, and then remove the bracket from the board (3). Component replacement procedures 45 3. Remove the board from the computer (4). Reverse this procedure to install the USB board. Fingerprint reader board To remove the fingerprint reader board, use this procedure and illustration. Table 6-6 Fingerprint reader board description and part number Description Fingerprint reader board Fingerprint reader board cable (included in Cable Kit) Fingerprint reader board bracket (included in Bracket Kit) Spare part number M07206-001 M05255-001 M05264-001 Before removing the fingerprint reader board, follow these steps: 1. Prepare the computer for disassembly (Preparation for disassembly on page 32). 2. Remove the bottom cover (Bottom cover on page 32). 3. Disconnect the battery cable from the system board (see Battery on page 41). 4. Remove the solid-state drive to the left of the battery (Solid-state drive on page 40). Remove the fingerprint reader board: 1. Remove the Phillips M2.0 × 2.0 screw (1) that secures the fingerprint reader bracket to the computer, and then remove the bracket (2). 2. Disconnect the cable from the ZIF connector on the fingerprint reader board (3). 46 Chapter 6 Removal and replacement procedures for authorized service provider parts 3. Remove the fingerprint reader board from the computer (4). Reverse this procedure to install the fingerprint reader board. Touchpad To remove the touchpad, use this procedure and illustration. Table 6-7 Touchpad description and part number Description Touchpad button board Touchpad Touchpad with NFC antenna Touchpad cable (included in Cable Kit) Spare part number M05267-001 M05269-001 M05270-001 M05255-001 Before removing the touchpad, follow these steps: 1. Prepare the computer for disassembly (Preparation for disassembly on page 32). 2. Remove the bottom cover (Bottom cover on page 32). 3. Remove the battery (see Battery on page 41). Remove the touchpad: 1. Disconnect the system board cable from the ZIF connector on the touchpad (1). 2. Disconnect the touchpad button board cable from the ZIF connector on the touchpad (2). 3. Remove the four Phillips M1.6 × 1.8 screws (3) that secure the touchpad to the computer. Component replacement procedures 47 4. Remove the touchpad button board from the computer (4). 5. Disconnect the cable from the reverse ZIF connector on the NFC module (1). 6. Disconnect the system board cable from the ZIF connector on the touchpad (2). 7. Disconnect the middle system board cable from the ZIF connector on the touchpad (3). 8. Disconnect the touchpad button board cable from the ZIF connector on the touchpad (4). 9. Remove the five Phillips M1.6 × 1.8 screws (5) that secure the touchpad to the computer. 10. Remove the touchpad from the computer (6). 48 Chapter 6 Removal and replacement procedures for authorized service provider parts Reverse this procedure to install the touchpad. NFC module To remove the NFC module, use this procedure and illustration. Table 6-8 NFC module description and part number Description NFC module NFC module cable (included in Cable Kit) Spare part number M07214-001 M05255-001 Before removing the NFC module, follow these steps: 1. Prepare the computer for disassembly (Preparation for disassembly on page 32). 2. Remove the bottom cover (Bottom cover on page 32). 3. Remove the battery (see Battery on page 41). Remove the NFC module: 1. Disconnect the system board cable from the ZIF connector on the NFC module (1). 2. Disconnect the touchpad cable from the reverse ZIF connector on the NFC module (2). 3. Use a tool to release the module (3), and then remove the module from the computer (4). The module is secured with adhesive. Fan Reverse this procedure to install the NFC module. To remove the fan, use this procedure and illustration. Component replacement procedures 49 Table 6-9 Fan description and part number Description Fan assembly Spare part number M05261-001 Before removing the fan, follow these steps: 1. Prepare the computer for disassembly (Preparation for disassembly on page 32). 2. Remove the bottom cover (Bottom cover on page 32). 3. Disconnect the battery cable from the system board (see Battery on page 41). Remove the fan assembly: 1. Remove the speaker cable from the clips on the left side of the fan (1). 2. Remove display cable and the WLAN antenna cables from the clips on the right side of the fan (2). 3. Disconnect the fan cable from the system board (3). 4. Loosen the two Phillips captive screws (4) that secure the fan to the computer, and then remove the fan from the computer (5). Reverse this procedure to install the fan assembly. Heat sink To remove the heat sink, use these procedures and illustrations. Table 6-10 Heat sink descriptions and part numbers Description Heat sink for use in models with discrete graphics memory Heat sink for use in models with UMA graphics memory Before removing the heat sink, follow these steps: 50 Chapter 6 Removal and replacement procedures for authorized service provider parts Spare part number M05263-001 M05262-001 1. Prepare the computer for disassembly (Preparation for disassembly on page 32). 2. Remove the bottom cover (Bottom cover on page 32). 3. Disconnect the battery cable from the system board (see Battery on page 41). Remove the heat sink: 1. To remove the heat sink on models with UMA graphics memory: a. In the order indicated on the heat sink, loosen the four captive Phillips screws (1) that secure the heat sink to the computer. b. Remove the heat sink from the computer (2). Component replacement procedures 51 c. Thoroughly clean the thermal material from the surfaces of the heat sink and the system board components each time the heat sink is removed. Replacement thermal material is included with the heat sink and system board spare part kits. The following illustration shows the replacement thermal material locations. Thermal material is used on the system board component (1) and on the heat sink area (2) that services it. 2. To remove the heat sink on models with discrete graphics memory: a. In the order indicated on the heat sink, loosen the six captive Phillips screws (1) that secure the heat sink to the computer. b. Remove the heat sink from the computer (2). 52 Chapter 6 Removal and replacement procedures for authorized service provider parts c. Thoroughly clean the thermal material from the surfaces of the heat sink and the system board components each time the heat sink is removed. Replacement thermal material is included with the heat sink and system board spare part kits. The following illustration shows the replacement thermal material locations. Thermal material is used on the system board components (1) (3) (5) and on the heat sink areas (2) (4) (6) that service them. Reverse this procedure to install the heat sink. System board To remove the system board, use these procedures and illustrations. Table 6-11 System board descriptions and part numbers Description System board (includes processor): All system boards use the following part numbers: xxxxxx-001: Non-Windows operating system xxxxxx-601: Windows 10 operating system Models with discrete graphics memory: Intel Core i7-10810 processor (OSR) Intel Core i7-10710 processor Intel Core i7-10610 processor Intel Core i7-10610 processor (OSR) Intel Core i7-10510 processor Intel Core i5-10310 processor Intel Core i5-10210 processor Spare part number M05245-xx1 M14257-xx1 M05243-xx1 M05244-xx1 M05241-xx1 M05242-xx1 M05240-xx1 Component replacement procedures 53 Table 6-11 System board descriptions and part numbers (continued) Description For use in models with UMA graphics memory: Intel Core i7-10810 processor (OSR) Intel Core i7-10710 processor Intel Core i7-10610 processor Intel Core i7-10610 processor (OSR) Intel Core i5-10210 processor Intel Core i5-10310 processor Intel Core i5-10310 processor (OSR) Intel Core i5-10210 processor Spare part number M05252-xx1 M14258-xx1 M05250-xx1 M05251-xx1 M05247-xx1 M05248-xx1 M05249-xx1 M05246-xx1 Before removing the system board, follow these steps: 1. Prepare the computer for disassembly (Preparation for disassembly on page 32). 2. Remove the bottom cover (Bottom cover on page 32). 3. Remove the battery (see Battery on page 41). 4. Remove the fan (see Fan on page 49). When you replace the system board, be sure to remove the following components (as applicable) from the defective system board and install them on the replacement system board: Memory modules (see Memory modules on page 33). WLAN module (see WLAN module on page 36). WWAN module (see WWAN module on page 38). Solid-state drive (see Solid-state drive on page 40). Heat sink (see Heat sink on page 50). Remove the system board: 1. Disconnect the following cables from the system board: Antenna cables from the WWAN module (select products only) (1) Power connector cable (2) Camera cable (3) Speaker cable (4) USB cable (ZIF) (5) Display cable (6) Card reader cable (ZIF) (7) Antenna cables from the WLAN module (8) Touchpad cable (ZIF) (9) 54 Chapter 6 Removal and replacement procedures for authorized service provider parts Keyboard backlight cable (ZIF) (select products only) (10) NFC module cable (ZIF) (select products only) (11) Keyboard cable (ZIF) (12) Fingerprint reader cable (ZIF) (select products only) (13) RTC battery cable (14) 2. Remove the four Phillips M2.0 × 4.0 screws (1) that secure the brackets to the system board, and then remove the plastic (2) and metal (3) brackets. The plastic bracket is available in the Plastics Kit as spare part number M16739-001. The metal bracket is available in the Bracket Kit as spare part number M05264-001. 3. Remove the five Phillips M2.0 × 4.0 screws (1) that secure the system board to the computer. Component replacement procedures 55 4. Remove the SIM card insert from the computer (2). 5. Lift the side of the system board upward (1), and then pull the system board away from the connectors on the side of the computer to remove it (2). Reverse this procedure to install the system board. Speakers To remove the speakers, use this procedure and illustration. Table 6-12 Speaker description and part number Description Speaker Kit Before removing the speakers, follow these steps: 56 Chapter 6 Removal and replacement procedures for authorized service provider parts Spare part number M05268-001 1. Prepare the computer for disassembly (Preparation for disassembly on page 32). 2. Remove the bottom cover (Bottom cover on page 32). 3. Remove the battery (see Battery on page 41). 4. Remove the system board (see System board on page 53). Remove the speakers: Remove the speakers from the computer (1) . For reinstallation, be sure that the rubber grommets are properly installed in the speakers (2). Reverse this procedure to install the speakers. Display assembly To remove and disassemble the display assembly, use these procedures and illustrations. Full hinge-up displays are not available as spare parts. Spare parts for displays are available only at the subcomponent level. Before removing the display panel, follow these steps: 1. Prepare the computer for disassembly (Preparation for disassembly on page 32). 2. Remove the bottom cover (Bottom cover on page 32). 3. Disconnect the battery cable from the system board (see Battery on page 41). 4. Remove the power connector cable (Power connector cable on page 44). Remove the display assembly: 1. Disconnect the antenna cables from the WWAN module (1), and then disconnect the display cable (2). 2. Remove the cables from the clip (3). 3. Disconnect the antenna cables from the WLAN module (4) and then disconnect the left display cable (5). Component replacement procedures 57 4. Remove the cables from the clips along the side of the fan (6). 5. Remove the six Phillips M2.5 × 4.0 screws (1) that secure the display assembly to the computer. 6. Rotate the display to open the hinges (2). 7. Separate the display assembly from the computer (3). 8. If you need to replace display assembly subcomponents: 58 Chapter 6 Removal and replacement procedures for authorized service provider parts a. Release the bezel by flexing and lifting the bottom (1), left and right sides (2), and top (3). b. Remove the bezel from the display (4). Bezels are available as the following spare part numbers: M05256-001: IR camera and ambient light sensor M05257-001: IR camera M05258-001: RGB camera and ambient light sensor M05259-001: RGB camera M05260-001: Microphone module only (no camera module) 9. If you need to remove the hinge cover from the display enclosure: a. Remove the Phillips M1.6 × 3.0 screw (1) that secures the hinge cover to the display. b. Slide the hinge cover toward the right (2). c. Rotate the bottom of the hinge cover up, and then remove it from the display (3). The hinge cover is available in the Hinge Kit as spare part number M05265-001. Component replacement procedures 59 10. If you need to remove the hinges from the display enclosure: a. Remove the three Phillips M2.0 × 10.0 screws (1) from each hinge. b. Remove the hinges from the display (2). The hinges are available in the Hinge Kit as spare part number M05265-001. 11. If you need to remove the display panel: a. The display panel is secured to the display enclosure with tape that is installed under the left and right sides of the panel. To remove the panel, use tweezers to grasp the end of the tape (1). While turning the tweezers, wrap the tape around the tweezers (2) as you continue to pull the tape out from behind the display panel (3). You must pull the tape multiple times before it is completely removed. 60 Chapter 6 Removal and replacement procedures for authorized service provider parts b. Rotate the display panel over and place it next to the display enclosure (4). Display panels are available as the following spare part numbers: M05236-001: 250 nit, nontouch panel M05237-001: 250 nit, Touch-on Panel (TOP) M05238-001: 400 nit, FHD panel M05239-001: 400 nit, UHD panel M14367-001: Privacy panel c. Lift the tape from the connector on the display panel (1), rotate the locking lever (2), and then disconnect the cable from the panel (3). Component replacement procedures 61 d. Remove the panel (4). 12. When replacing the display panel, follow these steps: IMPORTANT: Before installing the display panel, be sure to install the display cable to the back of the panel. a. Peel the protective layer from the bottom of the adhesive strips (1). b. Starting near the bottom of the inside of the display back cover (2), install the adhesive strips by aligning them with the groove on the edge of cover (3). c. Peel the protective layer from the top of the adhesive strips (4). d. Install the alignment tools onto the upper left and right corners of the display rear cover (5). 62 Chapter 6 Removal and replacement procedures for authorized service provider parts e. Insert the top of the panel into the top of the display rear cover (6), and then rotate the panel into place (7). Be sure that the upper corners of the panel are positioned up against the insides of the alignment tools. f. Remove the alignment tool. g. Replace the bezel by pressing along the bottom, sides, and then top of the bezel to snap it into place. Component replacement procedures 63 h. Install temporary rubber spacer strips on the left and right sides of the bezel (1), and hten close the display (2). i. Position the computer upside down on a table. j. Leave the computer upside down on the table for 20 minutes to allow the adhesive to set. k. Position the computer upright on a table. 64 Chapter 6 Removal and replacement procedures for authorized service provider parts l. Leave the computer upright on the table for 10 minutes to be sure the panel sits correctly in the display. m. Open the display and remove rubber spacer strips. 13. If you need to remove the hub board from the display: a. Disconnect the display cable from the ZIF connector (1) on the hub board. b. Disconnect the camera cable from the ZIF connector (2) on the hub board. c. Disconnect the smaller cables from the reverse ZIF connectors on the hub board (3) (4). d. Use a tool (5) to release the board from the display rear cover (6). The hub board is available as spare part number M07211-001 in models with an IR camera and M07210-001 in models with an RGB camera or microphone module. Component replacement procedures 65 14. If you need to remove the ambient light sensor from the display, disconnect the cable from the reverse ZIF connector on the board (1), and then use a tool (2) to release the sensor from the computer (3). The ambient light sensor is available as spare part number M07212-001. 15. If you need to remove the second ambient light sensor from the display, disconnect the cables from the ZIF connectors on the board (1), and then remove the sensor from the computer (2). The second ambient light sensor is available as spare part number M07213-001. 66 Chapter 6 Removal and replacement procedures for authorized service provider parts 16. If you need to remove the microphone board from the display, disconnect the cable from the reverse ZIF connector on the board (1), and then use a tool (2) to release the board from the computer (3). The microphone board is available as spare part number M07208-001 and M07209-001 for the rearfacing third microphone. 17. If you need to remove the camera module: Use a tool (1) to lift up evenly across the module and peel the module up from the display back cover (2), and then disconnect the cable from the reverse ZIF connector on the module (3). The camera module is available as spare part number M07216-001 for RGB cameras and M08549-001 for IR cameras. NOTE: For installation, note that the cable routes under the camera module before it connects to the module. Component replacement procedures 67 18. If you need to remove the display cable, disconnect the cable from the ZIF connector on the hub board (1), remove the cable from the clips at the bottom of the display back cover (2), and then remove the cable (3). The display panel cable is available as spare part number M05513-001. 19. If you need to remove the camera cable, disconnect the cable from the ZIF connector on the hub board (1), and then peel the cable off the inside of the display back cover to remove it (2). The camera cable is available in the Cable Kit as spare part number M05255-001. 68 Chapter 6 Removal and replacement procedures for authorized service provider parts 20. If you need to remove the WLAN antenna cables, peel the antennas off the inside of the display back cover (1), remove the cables from the clips at the bottom of the cover (2), (3), and then remove the antennas and cables (4). 21. If you need to remove the WWAN antenna cables, peel the antennas off the inside of the display back cover (1), remove the cables from the clips in the back (2) and near the hinge on the display back cover (3), and then remove the antennas and cables (4). Component replacement procedures 69 22. If you need to remove the ambient light sensor cable, disconnect the cable from the ZIF connectors on the ambient light sensor board (1) and hub board (2), and then peel the cable off the inside of the display back cover to remove it (3). The ambient light sensor cable is available in the Cable Kit as spare part number M05255-001. 70 Chapter 6 Removal and replacement procedures for authorized service provider parts 23. If you need to remove the second ambient light sensor cables, disconnect the cable from the ZIF connectors on the second ambient light sensor (1) and hub board (2), and then peel the cables off the inside of the display back cover to remove them (3). The second ambient light sensor cable is available in the Cable Kit as spare part number M05255-001. Display back covers are available as the following spare part numbers: M05254-001: Models with 250 nit, Touch-on Panel (TOP) M14250-001: Models with 400 nit panel, without WWAN M14251-001: Models with 400 nit FHD panel, with WWAN M14252-001: Models with 400 nit UHD panel, without WWAN 24. Use the following illustration to determine proper cable routing. The WWAN antenna cables and display cable route through the right hinge (1). The WLAN antenna cables and display cable route through the left hinge (2). Component replacement procedures 71 Reverse this procedure to reassemble and replace the display assembly. Keyboard with top cover The top cover with keyboard remains after removing all other spare parts from the computer. In this section, the first table provides the main spare part number for the top cover/keyboards. The second table provides the country codes. Table 6-13 Keyboard with top cover descriptions and part numbers Description Spare part number Keyboard with top cover, backlit Keyboard with top cover, not backlit Keyboard with top cover, backlit, for use in privacy models M07491-xx1 M07493-xx1 M07492-xx1 Table 6-14 Spare part country codes For use in country or region Spare part number Belgium -A41 Brazil -201 Bulgaria -261 Chile -161 Czech Republic/Slovakia -FL1 Denmark -081 Denmark, Finland, and Norway -DH1 French Canada -DB1 Finland/Sweden -B71 France -051 Germany -041 Greece -151 For use in country or region Hungary Iceland India Israel Italy Japan The Netherlands Northern Africa Norway Portugal Romania Russia Spare part number -211 -DD1 -D61 -BB1 -061 -291 -B31 For use in country or region Saudi Arabia Slovenia South Korea Spain Switzerland Taiwan Thailand -FP1 Turkey -091 Turkey-F -131 Ukraine -271 United Kingdom -251 United States Spare part number -171 -BA1 -AD1 -071 -BG1 -AB1 -281 -141 -541 -BD1 -031 -001 72 Chapter 6 Removal and replacement procedures for authorized service provider parts 7 Computer Setup (BIOS), TPM, and HP Sure Start HP provides several tools to help set up and protect your computer. Using Computer Setup Computer Setup, or Basic Input/Output System (BIOS), controls communication between all the input and output devices on the system (such as hard drives, display, keyboard, mouse, and printer). Computer Setup includes settings for types of devices installed, the startup sequence of the computer, and amount of system and extended memory. NOTE: Use extreme care when making changes in Computer Setup. Errors can prevent the computer from operating properly. To start Computer Setup, turn on or restart the computer, and when the HP logo appears, press f10 to enter Computer Setup. Navigating and selecting in Computer Setup You can navigate and select in Computer Setup using one or more methods. To select a menu or a menu item, use the tab key and the keyboard arrow keys and then press enter, or use a pointing device to select the item. To scroll up and down, select the up arrow or the down arrow in the upper-right corner of the screen, or use the up arrow key or the down arrow key on the keyboard. To close open dialog boxes and return to the main Computer Setup screen, press esc, and then follow the on-screen instructions. To exit Computer Setup, choose one of the following methods: To exit Computer Setup menus without saving your changes, select Main, select Ignore Changes and Exit, and then select Yes. NOTE: If you are using arrow keys to highlight your choice, you must then press enter. To save your changes and exit Computer Setup menus, select Main, select Save Changes and Exit, and then select Yes. NOTE: If you are using arrow keys to highlight your choice, you must then press enter. Your changes go into effect when the computer restarts. Restoring factory settings in Computer Setup To return all settings in Computer Setup to the values that were set at the factory, follow these steps. NOTE: Restoring defaults will not change the hard drive mode. Using Computer Setup 73 1. Start Computer Setup. See Using Computer Setup on page 73. 2. Select Main, select Apply Factory Defaults and Exit, and then select Yes. NOTE: If you are using arrow keys to highlight your choice, you must then press enter. NOTE: On select products, the selections might display Restore Defaults instead of Apply Factory Defaults and Exit. Your changes go into effect when the computer restarts. NOTE: Your password settings and security settings are not changed when you restore the factory settings. Updating the BIOS Updated versions of the BIOS might be available on the HP website. Most BIOS updates on the HP website are packaged in compressed files called SoftPaqs. Some download packages contain a file named Readme.txt, which contains information regarding installing and troubleshooting the file. Determining the BIOS version To decide whether you need to update Computer Setup (BIOS), first determine the BIOS version on your computer. You can access BIOS version information (also known as ROM date and System BIOS) by pressing fn+esc (if you are already in Windows) or by using Computer Setup. 1. Start Computer Setup. See Using Computer Setup on page 73. 2. Select Main, and then select System Information. 3. To exit Computer Setup menus without saving your changes, select Main, select Ignore Changes and Exit, and then select Yes. NOTE: If you are using arrow keys to highlight your choice, you must then press enter. To check for later BIOS versions, see Preparing for a BIOS update on page 74. Preparing for a BIOS update Be sure to follow all prerequisites before downloading and installing a BIOS update. IMPORTANT: To reduce the risk of damage to the computer or an unsuccessful installation, download and install a BIOS update only when the computer is connected to reliable external power using the AC adapter. Do not download or install a BIOS update while the computer is running on battery power, docked in an optional docking device, or connected to an optional power source. During the download and installation, follow these instructions: Do not disconnect power on the computer by unplugging the power cord from the AC outlet. Do not shut down the computer or initiate Sleep. Do not insert, remove, connect, or disconnect any device, cable, or cord. Downloading a BIOS update After you review the prerequisites, you can check for and download BIOS updates. 74 Chapter 7 Computer Setup (BIOS), TPM, and HP Sure Start 1. Type support in the taskbar search box, and then select the HP Support Assistant app. or Select the question mark icon in the taskbar. 2. Select Updates, and then select Check for updates and messages. 3. Follow the on-screen instructions. 4. At the download area, follow these steps: a. Identify the most recent BIOS update and compare it to the BIOS version currently installed on your computer. Make a note of the date, name, or other identifier. You might need this information to locate the update later, after it has been downloaded to your hard drive. b. Follow the on-screen instructions to download your selection to the hard drive. Make a note of the path to the location on your hard drive where the BIOS update is downloaded. You will need to access this path when you are ready to install the update. NOTE: If you connect your computer to a network, consult the network administrator before installing any software updates, especially system BIOS updates. Installing a BIOS update BIOS installation procedures vary. Follow any instructions that are displayed on the screen after the download is complete. If no instructions are displayed, follow these steps. 1. Type file in the taskbar search box, and then select File Explorer. 2. Select your hard drive designation. The hard drive designation is typically Local Disk (C:). 3. Using the hard drive path you recorded earlier, open the folder that contains the update. 4. Double-click the file that has an .exe extension (for example, filename.exe). The BIOS installation begins. 5. Complete the installation by following the on-screen instructions. NOTE: After a message on the screen reports a successful installation, you can delete the downloaded file from your hard drive. Changing the boot order using the f9 prompt To dynamically choose a boot device for the current startup sequence, follow these steps. 1. Access the Boot Device Options menu: Turn on or restart the computer, and when the HP logo appears, press f9 to enter the Boot Device Options menu. 2. Select a boot device, press enter, and then follow the on-screen instructions. TPM BIOS settings (select products only) TPM provides additional security for your computer. You can modify the TPM settings in Computer Setup (BIOS). TPM BIOS settings (select products only) 75 IMPORTANT: Before enabling Trusted Platform Module (TPM) functionality on this system, you must ensure that your intended use of TPM complies with relevant local laws, regulations and policies, and approvals or licenses must be obtained if applicable. For any compliance issues arising from your operation or usage of TPM that violates the previously mentioned requirement, you shall bear all the liabilities wholly and solely. HP will not be responsible for any related liabilities. NOTE: If you change the TPM setting to Hidden, TPM is not visible in the operating system. To access TPM settings in Computer Setup: 1. Start Computer Setup. See Using Computer Setup on page 73. 2. Select Security, select TPM Embedded Security, and then follow the on-screen instructions. Using HP Sure Start (select products only) Select computer models are configured with HP Sure Start, a technology that monitors the computer's BIOS for attacks or corruption. If the BIOS becomes corrupted or is attacked, HP Sure Start automatically restores the BIOS to its previously safe state, without user intervention. HP Sure Start is configured and already enabled so that most users can use the HP Sure Start default configuration. Advanced users can customize the default configuration. To access the latest documentation on HP Sure Start, go to http://www.hp.com/support. Select Find your product, and then follow the on-screen instructions. 76 Chapter 7 Computer Setup (BIOS), TPM, and HP Sure Start 8 Backing up, restoring, and recovering This chapter provides information about processes that are standard procedure for most products. Backing up your personal information--You can use Windows tools to back up your personal information (see Using Windows tools on page 77). Creating a restore point--You can use Windows tools to create a restore point (see Using Windows tools on page 77). Creating recovery media (select products only)--You can use the HP Cloud Recovery Download Tool (select products only) to create recovery media (see Using the HP Cloud Recovery Download Tool to create recovery media (select products only) on page 77). Restoring and recovery--Windows offers several options for restoring from backup, refreshing the computer, and resetting the computer to its original state (see Using Windows tools on page 77). IMPORTANT: If you will be performing recovery procedures on a tablet, the tablet battery must be at least 70% charged before you start the recovery process. IMPORTANT: For a tablet with a detachable keyboard, connect the tablet to the keyboard base before beginning any recovery process. Backing up information and creating recovery media These methods of creating recovery media and backups are available on select products only. Choose the appropriate method for your computer model. Using Windows tools You can use Windows tools to back up personal information and create system restore points and recovery media. IMPORTANT: Windows is the only option that allows you to back up your personal information. Schedule regular backups to avoid information loss. NOTE: If computer storage is 32 GB or less, Microsoft System Restore is disabled by default. For more information and steps, see the Get Help app. NOTE: You must be connected to the Internet to access the Get Help app. 1. Select the Start button, and then select the Get Help app. 2. Enter the task you want to perform. Using the HP Cloud Recovery Download Tool to create recovery media (select products only) You can use the HP Cloud Recovery Download Tool to create HP Recovery media on a bootable USB flash drive. For details: Go to http://www.hp.com/support, search for HP Cloud Recovery, and then select the result that matches the type of computer that you have. 77 NOTE: If you cannot create recovery media yourself, contact support to obtain recovery discs. Go to http://www.hp.com/support, select your country or region, and then follow the on-screen instructions. Restoring and recovery You have several options for recovering your system. Choose the method that best matches your situation and level of expertise. NOTE: Not all methods are available on all products. Restoring, resetting, and refreshing using Windows tools Windows offers several options for restoring, resetting, and refreshing the computer. For details, see Using Windows tools on page 77. Recovering using HP Recovery media You can use HP Recovery media to recover the original operating system and software programs that were installed at the factory. On select products, it can be created on a bootable USB flash drive using the HP Cloud Recovery Download Tool. For details, see Using the HP Cloud Recovery Download Tool to create recovery media (select products only) on page 77. NOTE: If you cannot create recovery media yourself, contact support to obtain recovery discs. Go to http://www.hp.com/support, select your country or region, and then follow the on-screen instructions. To recover your system: Insert the HP Recovery media, and then restart the computer. Changing the computer boot order If your computer does not restart using the HP Recovery media, you can change the computer boot order. This is the order of devices listed in BIOS where the computer looks for startup information. You can change the selection to an optical drive or a USB flash drive, depending on the location of your HP Recovery media. To change the boot order: IMPORTANT: For a tablet with a detachable keyboard, connect the tablet to the keyboard base before beginning these steps. 1. Insert the HP Recovery media. 2. Access the system Startup menu. For computers or tablets with keyboards attached, turn on or restart the computer or tablet, quickly press esc, and then press f9 for boot options. For tablets without keyboards, turn on or restart the tablet, quickly hold down the volume up button, and then select f9. or Turn on or restart the tablet, quickly hold down the volume down button, and then select f9. 3. Select the optical drive or USB flash drive from which you want to boot, and then follow the on-screen instructions. 78 Chapter 8 Backing up, restoring, and recovering Using HP Sure Recover (select products only) Select computer models are configured with HP Sure Recover, a PC OS recovery solution built into the hardware and firmware. HP Sure Recover can fully restore the HP OS image without installed recovery software. Using HP Sure Recover, an administrator or user can restore the system and install: Latest version of the operating system Platform-specific device drivers Software applications, in the case of a custom image To access the latest documentation for HP Sure Recover, go to http://www.hp.com/support. Select Find your product, and then follow the on-screen instructions. Restoring and recovery 79 9 Using HP PC Hardware Diagnostics You can use the HP PC Hardware Diagnostics utility to determine whether your computer hardware is running properly. The three versions are HP PC Hardware Diagnostics Windows, HP PC Hardware Diagnostics UEFI (Unified Extensible Firmware Interface), and (for select products only) Remote HP PC Hardware Diagnostics UEFI, a firmware feature. Using HP PC Hardware Diagnostics Windows (select products only) HP PC Hardware Diagnostics Windows is a Windows-based utility that allows you to run diagnostic tests to determine whether the computer hardware is functioning properly. The tool runs within the Windows operating system to diagnose hardware failures. If HP PC Hardware Diagnostics Windows is not installed on your computer, first you must download and install it. To download HP PC Hardware Diagnostics Windows, see Downloading HP PC Hardware Diagnostics Windows on page 81. Using an HP PC Hardware Diagnostics Windows hardware failure ID code When HP PC Hardware Diagnostics Windows detects a failure that requires hardware replacement, a 24-digit Failure ID code is generated. Depending on the instructions on the screen, choose one of these options: If failure ID link is displayed, select the link and follow the on-screen instructions. If instructions for calling support are displayed. Follow those instructions. Accessing HP PC Hardware Diagnostics Windows After HP PC Hardware Diagnostics Windows is installed, you can access it from HP Help and Support or HP Support Assistant. Accessing HP PC Hardware Diagnostics Windows from HP Help and Support After HP PC Hardware Diagnostics Windows is installed, follow these steps to access it from HP Help and Support. To access HP PC Hardware Diagnostics Windows from HP Help and Support: 1. Select the Start button, and then select HP Help and Support. 2. Select HP PC Hardware Diagnostics Windows. 3. When the tool opens, select the type of diagnostic test that you want to run, and then follow the on- screen instructions. NOTE: To stop a diagnostic test, select Cancel. 80 Chapter 9 Using HP PC Hardware Diagnostics Accessing HP PC Hardware Diagnostics Windows from Support Assistant After HP PC Hardware Diagnostics Windows is installed, follow these steps to access it from HP Support Assistant. To access HP PC Hardware Diagnostics Windows from HP Support Assistant: 1. Type support in the taskbar search box, and then select the HP Support Assistant app. or Select the question mark icon in the taskbar. 2. Select Troubleshooting and fixes. 3. Select Diagnostics, and then select HP PC Hardware Diagnostics Windows. 4. When the tool opens, select the type of diagnostic test that you want to run, and then follow the onscreen instructions. NOTE: To stop a diagnostic test, select Cancel. Downloading HP PC Hardware Diagnostics Windows The HP PC Hardware Diagnostics Windows downloading instructions are provided in English only. You must use a Windows computer to download this tool because only .exe files are provided. Downloading the latest HP PC Hardware Diagnostics Windows version from HP To download HP PC Hardware Diagnostics Windows from HP, follow these steps. 1. Go to http://www.hp.com/go/techcenter/pcdiags. The HP PC Diagnostics home page is displayed. 2. Select Download HP Diagnostics Windows, and then select a location on your computer or a USB flash drive. The tool downloads to the selected location. Downloading the HP PC Hardware Diagnostics Windows from the Microsoft Store You can download the HP PC Hardware Diagnostics Windows from the Microsoft Store. 1. Select the Microsoft Store app on your desktop or enter Microsoft Store in the taskbar search box. 2. Enter HP PC Hardware Diagnostics Windows in the Microsoft Store search box. 3. Follow the on-screen directions. The tool downloads to the selected location. Downloading HP Hardware Diagnostics Windows by product name or number (select products only) You can download HP PC Hardware Diagnostics Windows by product name or number. NOTE: For some products, you might have to download the software to a USB flash drive by using the product name or number. Using HP PC Hardware Diagnostics Windows (select products only) 81 1. Go to http://www.hp.com/support. 2. Select Software and Drivers, select your type of product, and then enter the product name or number in the search box that is displayed. 3. In the Diagnostics section, select Download, and then follow the on-screen instructions to select the specific Windows diagnostics version to be downloaded to your computer or USB flash drive. The tool downloads to the selected location. Installing HP PC Hardware Diagnostics Windows To install HP PC Hardware Diagnostics Windows, navigate to the folder on your computer or the USB flash drive where the .exe file downloaded, double-click the .exe file, and then follow the on-screen instructions. Using HP PC Hardware Diagnostics UEFI HP PC Hardware Diagnostics UEFI (Unified Extensible Firmware Interface) allows you to run diagnostic tests to determine whether the computer hardware is functioning properly. The tool runs outside the operating system so that it can isolate hardware failures from issues that are caused by the operating system or other software components. NOTE: For Windows 10 S computers, you must use a Windows computer and a USB flash drive to download and create the HP UEFI support environment because only .exe files are provided. For more information, see Downloading HP PC Hardware Diagnostics UEFI to a USB flash drive on page 83. If your PC does not start in Windows, you can use HP PC Hardware Diagnostics UEFI to diagnose hardware issues. Using an HP PC Hardware Diagnostics UEFI hardware failure ID code When HP PC Hardware Diagnostics UEFI detects a failure that requires hardware replacement, a 24-digit Failure ID code is generated. For assistance in solving the problem: Select Contact HP, accept the HP privacy disclaimer, and then use a mobile device to scan the Failure ID code that appears on the next screen. The HP Customer Support - Service Center page appears with your Failure ID and product number automatically filled in. Follow the on-screen instructions. or Contact support, and provide the Failure ID code. NOTE: To start diagnostics on a convertible computer, your computer must be in notebook mode, and you must use the attached keyboard. NOTE: If you need to stop a diagnostic test, press esc. Starting HP PC Hardware Diagnostics UEFI To start HP PC Hardware Diagnostics UEFI, follow this procedure. 1. Turn on or restart the computer, and quickly press esc. 2. Press f2. The BIOS searches three places for the diagnostic tools, in the following order: 82 Chapter 9 Using HP PC Hardware Diagnostics a. Connected USB flash drive NOTE: To download the HP PC Hardware Diagnostics UEFI tool to a USB flash drive, see Downloading the latest HP PC Hardware Diagnostics UEFI version on page 83. b. Hard drive c. BIOS 3. When the diagnostic tool opens, select a language, select the type of diagnostic test you want to run, and then follow the on-screen instructions. Downloading HP PC Hardware Diagnostics UEFI to a USB flash drive Downloading HP PC Hardware Diagnostics UEFI to a USB flash drive can be useful in some situations. HP PC Hardware Diagnostics UEFI is not included in the preinstallation image. HP PC Hardware Diagnostics UEFI is not included in the HP Tool partition. The hard drive is damaged. NOTE: The HP PC Hardware Diagnostics UEFI downloading instructions are provided in English only, and you must use a Windows computer to download and create the HP UEFI support environment because only .exe files are provided. Downloading the latest HP PC Hardware Diagnostics UEFI version To download the latest HP PC Hardware Diagnostics UEFI version to a USB flash drive, follow this procedure. 1. Go to http://www.hp.com/go/techcenter/pcdiags. The HP PC Diagnostics home page is displayed. 2. Select Download HP Diagnostics UEFI, and then select Run. Downloading HP PC Hardware Diagnostics UEFI by product name or number (select products only) You can download HP PC Hardware Diagnostics UEFI by product name or number (select products only) to a USB flash drive. NOTE: For some products, you might have to download the software to a USB flash drive by using the product name or number. 1. Go to http://www.hp.com/support. 2. Enter the product name or number, select your computer, and then select your operating system. 3. In the Diagnostics section, follow the on-screen instructions to select and download the specific UEFI Diagnostics version for your computer. Using Remote HP PC Hardware Diagnostics UEFI settings (select products only) Remote HP PC Hardware Diagnostics UEFI is a firmware (BIOS) feature that downloads HP PC Hardware Diagnostics UEFI to your computer. It can then execute the diagnostics on your computer, and it might upload results to a preconfigured server. For more information about Remote HP PC Hardware Diagnostics UEFI, go to http://www.hp.com/go/ techcenter/pcdiags, and then select Find out more. Using Remote HP PC Hardware Diagnostics UEFI settings (select products only) 83 Downloading Remote HP PC Hardware Diagnostics UEFI HP Remote PC Hardware Diagnostics UEFI is also available as a SoftPaq that you can download to a server. Downloading the latest Remote HP PC Hardware Diagnostics UEFI version You can download the latest HP PC Hardware Diagnostics UEFI version to a USB flash drive. 1. Go to http://www.hp.com/go/techcenter/pcdiags. The HP PC Diagnostics home page is displayed. 2. Select Download Remote Diagnostics, and then select Run. Downloading Remote HP PC Hardware Diagnostics UEFI by product name or number You can download HP Remote PC Hardware Diagnostics UEFI by product name or number. NOTE: For some products, you might have to download the software by using the product name or number. 1. Go to http://www.hp.com/support. 2. Select Software and Drivers, select your type of product, enter the product name or number in the search box that is displayed, select your computer, and then select your operating system. 3. In the Diagnostics section, follow the on-screen instructions to select and download the Remote UEFI version for the product. Customizing Remote HP PC Hardware Diagnostics UEFI settings Using the Remote HP PC Hardware Diagnostics setting in Computer Setup (BIOS), you can perform several customizations. Set a schedule for running diagnostics unattended. You can also start diagnostics immediately in interactive mode by selecting Execute Remote HP PC Hardware Diagnostics. Set the location for downloading the diagnostic tools. This feature provides access to the tools from the HP website or from a server that has been preconfigured for use. Your computer does not require the traditional local storage (such as a hard drive or USB flash drive) to run remote diagnostics. Set a location for storing the test results. You can also set the user name and password that you use for uploads. Display status information about the diagnostics run previously. To customize Remote HP PC Hardware Diagnostics UEFI settings, follow these steps: 1. Turn on or restart the computer, and when the HP logo appears, press f10 to enter Computer Setup. 2. Select Advanced, and then select Settings. 3. Make your customization selections. 4. Select Main, and then Save Changes and Exit to save your settings. Your changes take effect when the computer restarts. 84 Chapter 9 Using HP PC Hardware Diagnostics 10 Specifications This chapter provides specifications for your computer. Computer specifications This section provides specifications for your computer. When traveling with your computer, the computer dimensions and weights, as well as input power ratings and operating specifications, provide helpful information. Table 10-1 Computer specifications Metric U.S. Dimensions Width 359.5 mm 14.2 in Depth 233.7 mm 9.2 in Height (400 nits and above, nontouch) 19.2 mm 0.76 in Height (250 nits, nontouch or touch) 19.9 mm 0.78 in Weight Nontouch panel 1.75 kg 3.87 lbs Touch panel 1.90 kg 4.19 lbs Input power Operating voltage and current 19.5 V dc @ 2.31 A 45 W 19.5 V dc @ 3.33 A 65 W Temperature Operating 5°C to 35°C 41°F to 95°F Nonoperating 20°C to 60°C 4°F to 140°F Relative humidity (noncondensing) Operating 10% to 90% Nonoperating 5% to 95% Maximum altitude (unpressurized) Operating 15 m to 3,048 m 50 ft to 10,000 ft Nonoperating 15 m to 12,192 m 50 ft to 40,000 ft NOTE: Applicable product safety standards specify thermal limits for plastic surfaces. The device operates well within this range of temperatures. Computer specifications 85 39.6 cm (15.6 in) display specifications This section provides specifications for your display. Table 10-2 Display specifications Metric U.S. Active diagonal size 39.6 cm 15.6 in Resolution 1920 × 1080 3940 × 2160 Surface treatment Antiglare Brightness 250 nits (45% CG panels, touch and nontouch) 400 nits (sRGB 100% panels) 1000 nits (72% CG panels) Viewing angle UWVA Backlight LED Display panel interface eDP Solid-state drive specifications This section provides specifications for your solid-state drives. Table 10-3 Solid-state drive specifications 256 GB* Dimensions Height 1.0 mm Length 50.8 mm Width 28.9 mm Weight < 10 g Interface type PCIe Ready time, maximum (to not busy) 1.0 ms Access times, logical 0.1 ms Transfer rate Sequential read up to 2150 MB/s Random read Up to 300,000 IOPs Sequential write up to 1550 MB/s Random write Up to 100,000 IOPs Total logical sectors 468,883,296 Operating temperature 512 GB* 1 TB* 1.0 mm 50.8 mm 28.9 mm < 10 g PCIe < 1.0 ms 0.1 ms 1.0 mm 50.8 mm 28.9 mm < 10 g PCIe 1.0 ms 0.1 ms up to 2150 MB/s up to 2150 MB/s Up to 300,000 IOPs Up to 300,000 IOPs up to 1550 MB/s up to 1550 MB/s Up to 100,000 IOPs Up to 100,000 IOPs 1,000,215,216 1,500,336,388 0°C to 70°C (32°F to 158°F) 86 Chapter 10 Specifications Table 10-3 Solid-state drive specifications (continued) 256 GB* 512 GB* 1 TB* *1 GB = 1 billion bytes when referring to hard drive storage capacity. Actual accessible capacity is less. Actual drive specifications may differ slightly. NOTE: Certain restrictions and exclusions apply. Contact support for details. Solid-state drive specifications 87 11 Statement of memory volatility For general information regarding nonvolatile memory in HP Business computers, and to restore nonvolatile memory that can contain personal data after the system has been turned off and the hard drive has been removed, use these instructions. HP Business computer products that use Intel®-based or AMD®-based system boards contain volatile DDR memory. The amount of nonvolatile memory present in the system depends upon the system configuration. Intel-based and AMD-based system boards contain nonvolatile memory subcomponents as originally shipped from HP, with the following assumptions: No subsequent modifications were made to the system. No applications, features, or functionality were added to or installed on the system. Following system shutdown and removal of all power sources from an HP Business computer system, personal data can remain on volatile system memory (DIMMs) for a finite period of time and also remains in nonvolatile memory. Use the following steps to remove personal data from the computer, including the nonvolatile memory found in Intel-based and AMD-based system boards. NOTE: If your tablet has a keyboard base, connect to the keyboard base before beginning steps in this chapter. Current BIOS steps Use these instructions to restore nonvolatile memory. 1. Follow these steps to restore the nonvolatile memory that can contain personal data. Restoring or reprogramming nonvolatile memory that does not store personal data is neither necessary nor recommended. a. Turn on or restart the computer, and then quickly press esc. NOTE: If the system has a BIOS administrator password, enter the password at the prompt. b. Select Main, select Apply Factory Defaults and Exit, and then select Yes to load defaults. The computer restarts. c. During the restart, press esc while the "Press the ESC key for Startup Menu" message is displayed at the bottom of the screen. NOTE: If the system has a BIOS administrator password, enter the password at the prompt. d. Select the Security menu, select Restore Security Settings to Factory Defaults, and then select Yes to restore security level defaults. The computer reboots. e. During the reboot, press esc while the "Press the ESC key for Startup Menu" message is displayed at the bottom of the screen. NOTE: If the system has a BIOS administrator password, enter the password at the prompt. f. If an asset or ownership tag is set, select the Security menu and scroll down to the Utilities menu. Select System IDs, and then select Asset Tracking Number. Clear the tag, and then make the selection to return to the prior menu. 88 Chapter 11 Statement of memory volatility g. If a DriveLock password is set, select the Security menu, and scroll down to Hard Drive Utilities under the Utilities menu. Select Hard Drive Utilities, select DriveLock, and then clear the check box for DriveLock password on restart. Select OK to proceed. h. Select the Main menu, and then select Reset BIOS Security to factory default. Click Yes at the warning message. The computer reboots. i. During the reboot, press esc while the "Press the ESC key for Startup Menu" message is displayed at the bottom of the screen. NOTE: If the system has a BIOS administrator password, enter the password at the prompt. j. Select the Main menu, select Apply Factory Defaults and Exit, select Yes to save changes and exit, and then select Shutdown. k. Reboot the system. If the system has a Trusted Platform Module (TPM), fingerprint reader, or both, one or two prompts will appear--one to clear the TPM and the other to Reset Fingerprint Sensor. Press or tap f1 to accept or f2 to reject. l. Remove all power and system batteries for at least 24 hours. 2. Complete one of the following: Remove and retain the storage drive. or Clear the drive contents by using a third-party utility designed to erase data from an SSD. or Clear the contents of the drive by using the following BIOS Setup Secure Erase command option steps: If you clear data using Secure Erase, you cannot recover it. a. Turn on or restart the computer, and then quickly press esc. b. Select the Security menu and scroll down to the esc menu. c. Select Hard Drive Utilities. d. Under Utilities, select Secure Erase, select the hard drive storing the data you want to clear, and then follow the on-screen instructions to continue. or Clear the contents of the drive using the following Disk Sanitizer commands steps: i. Turn on or restart the computer, and then quickly press esc. ii. Select the Security menu and scroll down to the Utilities menu. iii. Select Hard Drive Utilities. iv. Under Utilities, select Disk Sanitizer, select the hard drive with the data that you want to clear, and then follow the on-screen instructions to continue. NOTE: The amount of time it takes for Disk Sanitizer to run can take several hours. Plug the computer into an AC outlet before starting. Current BIOS steps 89 Nonvolatile memory usage Use this table to troubleshooting nonvolatile memory usage. Table 11-1 Troubleshooting steps for nonvolatile memory usage Nonvolatile memory type Amount (Size) Does this memory store customer data? Does this memory retain data when power is removed? What is the purpose of this How is data entered into this How is this memory memory? memory? write-protected? HP Sure Start flash 8 MB (select models only) No Yes Provides Data cannot be written to this This memory is protected protected device via the host processor. by the HP Sure Start backup of The content is managed Embedded Controller. critical System solely by the HP Sure Start BIOS code, EC Embedded Controller. firmware, and critical computer configuration data for select platforms that support HP Sure Start. For more information, see Using HP Sure Start (select products only) on page 93. Real Time Clock 256 bytes No Yes Stores system RTC battery backed-up CMOS This memory is not write- (RTC) battery date and time is programmed using protected. backed-up CMOS and noncritical Computer Setup (BIOS), or by configuration data. changing the Windows date & memory time. Controller (NIC) 64 KB (not No Yes Stores NIC NIC EEPROM is programmed A utility must be used to EEPROM customer configuration using a utility from the NIC write data to this memory accessible) and NIC vendor that can be run from and is available from the firmware. DOS. NIC vendor. Writing data to this ROM in an inappropriate manner will render the NIC non- functional. DIMM Serial 256 bytes per No Yes Stores memory DIMM SPD is programmed by Data cannot be written to Presence Detect memory module the memory vendor. this memory when the (SPD) module, 128 information. module is installed in a configuration data bytes computer. The specific programmable write-protection method (not customer varies by memory vendor. accessible) System BIOS 9 MB Yes Yes Stores system BIOS code and computer configuration data. System BIOS code is programmed at the factory. Code is updated when the system BIOS is updated. Configuration data and settings are entered using the Computer Setup (BIOS) or a custom utility. NOTE: Writing data to this ROM in an inappropriate manner can render the computer nonfunctional. A utility must be used for writing data to this memory and is available 90 Chapter 11 Statement of memory volatility Table 11-1 Troubleshooting steps for nonvolatile memory usage (continued) Nonvolatile memory type Amount (Size) Does this memory store customer data? Does this memory retain data when power is removed? What is the purpose of this How is data entered into this How is this memory memory? memory? write-protected? on the HP website; go to http://www.hp.com/ support. Select Find your product, and then follow the on-screen instructions. Intel Management 1.5 MB or 7 MB Yes Yes Engine Firmware (present only in select Elite or Z models. For more information, go to http://www.hp.com/ support. Select Identify your product for manuals and specific product information, and then follow the on-screen instructions.) Stores Management Engine Code, Settings, Provisioning Data and iAMT third-party data store. Management Engine Code is programmed at the factory. Code is updated via Intel secure firmware update utility. Unique Provisioning Data can be entered at the factory or by an administrator using the Management Engine (MEBx) setup utility. The third-party data store contents can be populated by a remote management console or local applications that have been registered by an administrator to have access to the space. The Intel chipset is configured to enforce hardware protection to block all direct read-write access to this area. An Intel utility must be used for updating the firmware. Only firmware updates digitally signed by Intel can be applied using this utility. Bluetooth flash 2 megabits No Yes Stores Bluetooth flash is A utility must be used for (select products Bluetooth programmed at the factory. writing data to this only) configuration Tools for writing data to this memory and is made and firmware. memory are not publicly available through newer available but can be obtained versions of the driver from the silicon vendor. whenever the flash requires an upgrade. 802.11 WLAN 4 kilobits to 8 No Yes Stores 802.11 WLAN EEPROM is A utility must be used for EEPROM kilobits configuration programmed at the factory. writing data to this and calibration Tools for writing data to this memory and is typically data. memory are not made public. not made available to the public unless a firmware upgrade is necessary to address a unique issue. Camera (select 64 kilobits No Yes Stores camera Camera memory is A utility must be used for products only) configuration programmed using a utility writing data to this and firmware. from the device memory and is typically manufacturer that can be run not made available to the from Windows. public unless a firmware upgrade is necessary to address a unique issue. Fingerprint reader 512 KB flash Yes Yes (select products only) Stores fingerprint templates. Fingerprint reader memory is programmed by user enrollment in HP ProtectTools Security Manager. Only a digitally signed application can make the call to write to the flash. Nonvolatile memory usage 91 Questions and answers Use this section to answer your questions about nonvolatile memory. 1. How can the BIOS settings be restored (returned to factory settings)? IMPORTANT: The restore defaults feature does not securely erase any data on your hard drive. See question and answer 6 for steps to securely erase data. The restore defaults feature does not reset the Custom Secure Boot keys. See question and answer 7 for information about resetting the keys. a. Turn on or restart the computer, and then quickly press esc. b. Select Main, and then select Apply Factory Defaults and Exit. c. Follow the on-screen instructions. d. Select Main, select Save Changes and Exit, and then follow the on-screen instructions. 2. What is a UEFI BIOS, and how is it different from a legacy BIOS? The Unified Extensible Firmware Interface (UEFI) BIOS is an industry-standard software interface between the platform firmware and an operating system (OS). It replaces the older BIOS architecture but supports much of the legacy BIOS functionality. Like the legacy BIOS, the UEFI BIOS provides an interface to display the system information and configuration settings and to change the configuration of your computer before an OS is loaded. BIOS provides a secure runtime environment that supports a Graphic User Interface (GUI). In this environment, you can use either a pointing device (touch screen, touchpad, pointing stick, or USB mouse) or the keyboard to navigate and make menu and configuration selections. The UEFI BIOS also contains basic system diagnostics. The UEFI BIOS provides functionality beyond that of the legacy BIOS. In addition, the UEFI BIOS works to initialize the computer's hardware before loading and executing the OS; the runtime environment allows the loading and execution of software programs from storage devices to provide more functionality, such as advanced hardware diagnostics (with the ability to display more detailed system information) and advanced firmware management and recovery software. HP has provided options in Computer Setup (BIOS) to allow you to run in legacy BIOS, if required by the operating system. Examples of this requirement would be if you upgrade or downgrade the OS. 3. Where is the UEFI BIOS located? The UEFI BIOS is located on a flash memory chip. You must use a utility to write to the chip. 4. What kind of configuration data is stored on the DIMM Serial Presence Detect (SPD) memory module? How would this data be written? The DIMM SPD memory contains information about the memory module, such as size, serial number, data width, speed and timing, voltage, and thermal information. This information is written by the module manufacturer and stored on an EEPROM. You cannot write to this EEPROM when the memory module is installed in a computer. Third-party tools do exist that can write to the EEPROM when the memory module is not installed in a computer. Various third-party tools are available to read SPD memory. 5. What is meant by "Restore the nonvolatile memory found in Intel-based system boards"? This message relates to clearing the Real Time Clock (RTC) CMOS memory that contains computer configuration data. 6. How can the BIOS security be reset to factory defaults and erase the data? 92 Chapter 11 Statement of memory volatility IMPORTANT: Resetting results in the loss of information. These steps do not reset Custom Secure Boot Keys. See question and answer 7 for information about resetting the keys. a. Turn on or restart the computer, and then quickly press esc. b. Select Main, and then select Reset Security to Factory Defaults. c. Follow the on-screen instructions. d. Select Main, select Save Changes and Exit, and then follow the on-screen instructions. 7. How can the Custom Secure Boot Keys be reset? Secure Boot is a feature to ensure that only authenticated code can start on a platform. If you enabled Secure Boot and created Custom Secure Boot Keys, disabling Secure Boot does not clear the keys. You must also select to clear the Custom Secure Boot Keys. Use the same Secure Boot access procedure that you used to create the Custom Secure Boot Keys, but select to clear or delete all Secure Boot Keys. a. Turn on or restart the computer, and then quickly press esc. b. Select the Security menu, select Secure Boot Configuration, and then follow the on-screen instructions. c. At the Secure Boot Configuration window, select Secure Boot, select Clear Secure Boot Keys, and then follow the on-screen instructions to continue. Using HP Sure Start (select products only) Select computer models are configured with HP Sure Start, a technology that continuously monitors your computer's BIOS for attacks or corruption. If the BIOS becomes corrupted or is attacked, HP Sure Start restores the BIOS to its previously safe state, without user intervention. Those select computer models ship with HP Sure Start configured and enabled. HP Sure Start is configured and already enabled so that most users can use the HP Sure Start default configuration. Advanced users can customize the default configuration. To access the latest documentation on HP Sure Start, go to http://www.hp.com/support. Using HP Sure Start (select products only) 93 12 Power cord set requirements This chapter provides power cord requirements for countries and regions. The wide-range input feature of the computer permits it to operate from any line voltage from 100 V ac to 120 V ac, or from 220 V ac to 240 V ac. The 3-conductor power cord set included with the computer meets the requirements for use in the country or region where the equipment is purchased. Power cord sets for use in other countries or regions must meet the requirements of the country and region where the computer is used. Requirements for all countries These power cord requirements are applicable to all countries and regions. The length of the power cord set must be at least 1.0 m (3.3 ft) and no more than 2.0 m (6.5 ft). All power cord sets must be approved by an acceptable accredited agency responsible for evaluation in the country or region where the power cord set will be used. The power cord sets must have a minimum current capacity of 10 A and a nominal voltage rating of 125 V ac or 250 V ac, as required by the power system of each country or region. The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320 Standard Sheet C13 connector for mating with the appliance inlet on the back of the computer. Requirements for specific countries and regions To determine power cord requirements for specific countries and regions, use this table. Table 12-1 Power cord requirements for specific countries and regions Country/region Accredited agency Applicable note number Argentina IRAM 1 Australia SAA 1 Austria OVE 1 Belgium CEBEC 1 Brazil ABNT 1 Canada CSA 2 Chile IMQ 1 Denmark DEMKO 1 Finland FIMKO 1 France UTE 1 Germany VDE 1 94 Chapter 12 Power cord set requirements Table 12-1 Power cord requirements for specific countries and regions (continued) Country/region Accredited agency Applicable note number India BIS 1 Israel SII 1 Italy IMQ 1 Japan JIS 3 The Netherlands KEMA 1 New Zealand SANZ 1 Norway NEMKO 1 The People's Republic of China CCC 4 Saudi Arabia SASO 7 Singapore PSB 1 South Africa SABS 1 South Korea KTL 5 Sweden SEMKO 1 Switzerland SEV 1 Taiwan BSMI 6 Thailand TISI 1 The United Kingdom ASTA 1 The United States UL 2 1. The flexible cord must be Type HO5VV-F, 3-conductor, 0.75 mm² conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used. 2. The flexible cord must be Type SVT/SJT or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole grounding type with a NEMA 5-15P (15 A, 125 V ac) or NEMA 6-15P (15 A, 250 V ac) configuration. CSA or C-UL mark. UL file number must be on each element. 3. The appliance coupler, flexible cord, and wall plug must bear a T mark and registration number in accordance with the Japanese Dentori Law. The flexible cord must be Type VCTF, 3-conductor, 0.75 mm² or 1.25 mm² conductor size. The wall plug must be a two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V ac) configuration. 4. The flexible cord must be Type RVV, 3-conductor, 0.75 mm² conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the CCC certification mark. 5. The flexible cord must be Type H05VV-F 3-conductor, 0.75 mm² conductor size. KTL logo and individual approval number must be on each element. Approval number and logo must be printed on a flag label. 6. The flexible cord must be Type HVCTF 3-conductor, 1.25 mm² conductor size. Power cord set fittings (appliance coupler, cable, and wall plug) must bear the BSMI certification mark. 7. For 127 V ac, the flexible cord must be Type SVT or SJT 3-conductor, 18 AWG, with plug NEMA 5-15P (15 A, 125 V ac), with UL and CSA or C-UL marks. For 240 V ac, the flexible cord must be Type H05VV-F 3-conductor, 0.75 mm² or 1.00 mm² conductor size, with plug BS 1363/A with BSI or ASTA marks. Requirements for specific countries and regions 95 13 Recycling When a nonrechargeable or rechargeable battery has reached the end of its useful life, do not dispose of the battery in general household waste. Follow the local laws and regulations in your area for battery disposal. HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable batteries. For more information about recycling programs, see the HP website at http://www.hp.com/recycle. 96 Chapter 13 Recycling Index A AC adapters, spare part numbers 24 ambient light sensor, identifying 9 audio-out (headphone)/audio-in (microphone) combo jack 8 B backup, creating 77 backups 77 BIOS determining version 74 downloading an update 74, 75 updating 74 Bluetooth label 16 boot order changing using the f9 prompt 75 boot order, changing 78 bottom components 15 bottom cover removal 32 spare part number 32 Bracket Kit spare part number 23 buttons power 13, 14 programmable key 14 C Cable Kit spare part number 24 camera identifying 10 camera light, identifying 9 camera privacy cover identifying 10 caps lock light 12 card reader board removal 43 spare part number 43 cases, spare part numbers 24 cautions electrostatic discharge 27, 28 component bottom 15 components display 9 keyboard area 10 left side 8 right side 7 computer major components 18 Computer Setup navigating and selecting 73 restoring factory settings 73 starting 73 computer specifications 85 D display specifications 85, 86 display assembly subcomponents 21 display back cover illustrated 21 spare part number 21 display bezel illustrated 21 spare part number 21 display cable illustrated 21 spare part number 21 display components 9 display panel illustrated 21 spare part number 21 docks, spare part numbers 24 E electrostatic discharge (ESD) 27, 28 preventing damage 27, 28, 29 esc key, identifying keys esc 14 F fan removal 49 spare part number 49 fingerprint reader board removal 46 spare part numbers 46 fingerprint reader bracket illustrated 23 fingerprint reader insert illustrated 23 fingerprint reader, identifying 14 fn key, identifying 14 G grounding methods 27, 28, 30 guidelines packaging 27, 31 transporting 27, 31 workstation 27, 28 H hard drive specifications 85 heat sink removal 50 spare part numbers 50 hinge illustrated 21 spare part number 21 hinge cover illustrated 21 spare part number 21 hot keys using 15 HP PC Hardware Diagnostics UEFI downloading 83 starting 82 using 82 HP PC Hardware Diagnostics Windows accessing 80, 81 downloading 81 installing 82 using 80 HP Recovery media recovery 78 HP Sure Recover 79 HP Sure Start 88, 93 hubs, spare part numbers 24 Index 97 I I/O bracket insert illustrated 23 illustrated parts catalog 18 integrated numeric keypad, identifying 15 internal microphones, identifying 10 J jacks audio-out (headphone)/audio-in (microphone) combo, identifying 8 K keyboard product description 4 keyboard with top cover spare part numbers 72 keys action 14 fn 14 num lk 15 Windows 14 L labels Bluetooth 16 regulatory 16 serial number 16 service 16 wireless certification 16 WLAN 16 left side components 8 lights camera 9 caps lock 12 mute 12 mute light, identifying 12 locks, spare part numbers 24 M memory nonvolatile 88 volatile 88 memory cover illustrated 23 memory modules removal 33 spare part numbers 33 mice, spare part numbers 24 N nano SIM card slot 7 NFC module removal 49 spare part number 49 nonvolatile memory 88 num lk key, identifying 15 P packaging guidelines 27, 31 Plastics Kit spare part number 23 pointing device, product description 4 ports product description 3 USB SuperSpeed 8 USB Type-C power connector and Thunderbolt, identifying 7 power button, identifying 13, 14 power connector cable removal 44 spare part number 44 power cord requirements for all countries 94 requirements for specific countries and regions 94 set requirements 94 power cords, spare part numbers 24 product description keyboard 4 pointing device 4 ports 3 sensors 4 product name and number, computer 16 programmable key, identifying 14 R recovery 77, 78 discs 78 media 78 USB flash drive 78 recovery media 77 creating using HP Cloud Recovery Download Tool 77 creating using Windows tools 77 regulatory information regulatory label 16 wireless certification labels 16 Remote HP PC Hardware Diagnostics UEFI settings customizing 84 using 83 removal and replacement procedures 32, 41 solid-state drive 40 removing personal data from volatile system memory 88 restoring 77 right side components 7 S Screw Kit, spare part number 24 sensors product description 4 serial number, computer 16 service labels, locating 16 setup utility navigating and selecting 73 restoring factory settings 73 SIM card insert illustrated 23 slots nano SIM card 7 smart card insert illustrated 23 solid-state drive removal and replacement 40 specifications 86 spare part country codes 72 speaker removal 56 spare part numbers 56 speakers, identifying 13 special keys, using 14 specifications computer 85 display 85, 86 hard drive 85 solid-state drive 86 static electricity 27, 28, 29 Sure Start using 76 system board removal 53 spare part numbers 53 98 Index system memory, removing personal data from volatile 88 system restore point, creating 77 T touchpad removal 47 spare part number 47 TPM settings 75 transporting guidelines 27, 31 traveling with the computer 16 U USB board removal 45 spare part number 45 USB bracket illustrated 23 USB SuperSpeed ports identifying 8 USB Type-C power connector and ThunderboltTM ports 7 V vents, identifying 13 W Windows backup 77 recovery media 77 system restore point 77 Windows key, idenitfying 14 Windows tools, using 77 wireless antennas illustrated 21 spare part number 21 wireless antennas, identifying 9 wireless certification label 16 WLAN antennas, identifying 9 WLAN device 16 WLAN label 16 WLAN module removal 36 spare part numbers 36 workstation guidelines 27, 28 WWAn antennas, identifying 9 WWAN insulator illustrated 23 WWAN module removal 38 spare part numbers 38 Index 99AH XSL Formatter V6.2 MR2 for Windows (x64) : 6.2.4.17534 (2014/06/19 09:55JST) Antenna House PDF Output Library 6.2.553 (Windows (x64))