各種ダウンロード｜HIOS
For DC Screwdrivers Power Supply CLT-45/CLT-60 JP EN Operation Manual HIOS Inc. JAPAN HIOS ROTATION 2 POWER I ON 1 OFF POWER SUPPLY WT-A016 19A JP 5 2 2P 1 AC100V CLT-45 1 1 CLT-60 2 4 1.8m JP CLT-45 CLT-60 1 2 HIOS Inc. JAPAN HIOS ROTATION 2 POWER I ON 1 OFF POWER SUPPLY 3 4 5 ROTATION POWER I ON O OFF 1POWER 2 32HIDC30V1LOWDC20V 4 5 3 OPC/SS CLT-45 CL SS JP CL-2000CL-3000CL-4000CL-6000CL-6500 SS-2000SS-3000SS-4000SS-6500 -4500-5000 CLT-60 CL SS CL-2000CL-3000CL-4000CL-6000CL-6500CL-7000 SS-2000SS-3000SS-4000SS-6500SS-7000 -4500-5000-6500 2HIDC30V1LOW DC20V 4 CLT-45 CLT-60 JP 5 CLT-45 CLT-60 AC100-240V47-63Hz 45-78VA 40-65VA 3.15A/250V 5A/250V HI 2DC30VLOW1DC20V2 JP NN NN NN NN NN NN 330g 715g 1 6 Important Safety Instructions Before using this machine, read this section and follow the instructions to properly use this machine. Installation The unit should be used in a temperature and humidity-controlled room. Keep the unit away from a place with poor ventilation, in dust or metal pieces. Do not place any objects on the unit. The place to install the unit should be vibration-free and the unit should be securely fixed. If the unit is installed on the wall or on a high place, make sure to use the attached Mounting Bracket to fix it securely. Do not install the unit close to high voltage equipments. Handling EN Install a leakage breaker and safety breaker on the input power source and connect the ground to use the unit. Connect to a power source of the specified voltage. Do not use with other drivers or devices except the models listed in this operation manual. If the protection circuit works due to overheat, stop operation immediately, pull the power plug from the outlet and send it back to your HIOS distributor for repair. The unit may automatically stop in use when the protection circuit works due to overcurrent, etc. Turn off the power switch once and turn it on in 5 seconds for restart. If the unit stops while in screw fastening, make sure to check the torque of the fastened screw. Do not disassemble or modify the unit. Do not drop the power Supply or subject it to violent impact. Do not drag the unit by its driver cord or AC cord. Keep the cords away from foreign objects, oil or something sharp. Make sure to grasp the plug section to disconnect the AC cord from the outlet. Turn the unit off and disconnect the AC cord from the outlet when the unit is not in use. IMPORTANT SAFETY INSTRUCTIONS-SAVE THESE INSTRUCTIONS. DANGER-TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK. CAREFULLY FOLLOW THESE INSTRUCTIONS. Selection of Power Supply Cord: Use in U.S.A. - Use UL Listed detachable power supply cord, No.18AWG,3 conductors, flexible cord, rated 10A, VW-1, 80°C, minimum 1.8 m, maximum 3 m long. Provided with a molded-on, non-polarized attachment plug with a 15A, 125V (NEMA5-15P) or 15A, 250 V (NEMA 6-15P) configuration and a molded-on connector which mates with the Power Inlet. The following flexible cord type may be used: S, SE, SO, SP-3, SPT-3, ST,STO, SJ, SJE, SJO, SJT, SJTO, SP-2, SPE-2, SPT-2, SV, SVE, SVT. Use in countries other than U.S.A. - Use IEC60227 certified PVC flexible power supply cord, marked H03VVF or H05VVF, 3C x 0.75 mm2, rated min. 10A, 250V 7 Accessories CLT-45 CLT-60 Mounting Bracket 1pc 2pcs Screw 1pc 4pcs Parts and Their Functions EN CLT-45 AC Cord (1.8m) CLT-60 Front Side Back Side 1 2 HIOS Inc. JAPAN HIOS ROTATION 2 POWER I ON 1 OFF POWER SUPPLY 3 4 5 ROTATION POWER I ON O OFF 1Power Indicator: Lights up when the power switch is turned ON. 2Connector for the Screwdriver: Connect the screwdriver cord. 3DC Output Switch: 2 (HI: DC30V) / 1 (LOW: DC20V) 4Power Switch: Turns the power ON or OFF. 5Connector for AC Cord: Connect the power cord. 8 Compatible Screwdrivers (Including OPC/SS Type) CLT-45 Series CL SS Model CL-2000/CL-3000/CL-4000/CL-6000/CL-6500 SS-2000/SS-3000/SS-4000/SS-6500 -4500/-5000 CLT-60 EN Series Model CL CL-2000/CL-3000/CL-4000/CL-6000/CL-6500/CL-7000 SS SS-2000/SS-3000/SS-4000/SS-6500/SS-7000 -4500/-5000/-6500 * Use only 2(HI) power outlet with the *models. These models may not perform properly on 1(LOW) power outlet. 9 Attach the Mounting Bracket Make sure to use the attached Mounting Bracket and the screw to fix the unit securely if you install it on the work table, the wall, etc. CLT-45 CLT-60 EN Example 10 Specifications Model Name Input Voltage Primary Side Power Consumption Secondary Output Voltage CLT-45 CLT-60 AC100-240V (47-63Hz) 45-78VA Fuse capacity: 3.15A/250V (Built-in) 40-65VA Fuse capacity: 5A/250V (Built-in) HI(2): DC30V / LOW(1): DC20V (2-step switchable) NN NN EN NN NN External Dimensions NN NN Weight Number of Connectable Screwdrivers 330g 1 unit 715g 11 1-35-1 TEL03-6661-8777FAX03-6657-0888 HIOS Inc. 1-35-1 Oshiage, Sumida-ku Tokyo, Japan TEL: +81-3-6661-8821 / FAX: +81-3-6661-8828Adobe PDF Library 9.9 Adobe InDesign CS5.5 J (7.5)