Dreame X40 Ultra Robot Vacuum and Mop with Auto-Empty and Mop Self-Cleaning

Safety Information

To avoid electric shock, fire, or injury caused by improper use of the appliance, please read the user manual carefully before using the appliance and keep it for future reference.

Usage Restrictions

• This product should not be used by children younger than 8 years old nor persons with physical, sensory, intellectual deficiencies, or limited experience or knowledge without the supervision of a parent or guardian to ensure safe operation and to avoid any risks. Cleaning and maintenance shall not be performed by children without supervision.
• The appliance is only to be used with the power supply unit provided with the appliance.
• This appliance contains batteries that are only replaceable by skilled persons.
• Clear the area to be cleaned. Children shall not play with the appliance. Ensure children and pets are kept at a safe distance from the robot while it is operating.
• Do not install, charge, or use the appliance in bathrooms or around pools.
• This product is for floor cleaning in a home environment only. Do not use it outdoors, on non-floor surfaces, or in a commercial or industrial setting.
• Ensure that the appliance operates correctly in a proper environment. Otherwise, do not use the appliance.
• If the power cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.
• Do not use the robot in an area suspended above ground level without a protective barrier.
• Do not place the robot upside down. Do not use the LDS cover, robot cover, or bumper as a handle for the robot.
• Use the robot in environments with an ambient temperature above 0°C and below 40°C. Make sure there is no liquid or sticky substance on the floor.
• To prevent damage or harm from dragging, clear any loose objects from the floor, and remove cables or power cords on the cleaning path before operating the appliance.
• Remove fragile or small items from the floor to prevent the robot from bumping into and damaging them.
• Keep hair, fingers, and other body parts away from the suction opening of the robot.
• Keep the cleaning tool out of reach of children.
• Do not operate the appliance in a room where an infant or child is sleeping.
• Do not place children, pets, or any item on top of the robot regardless of whether it is stationary or moving.
• Only clean water and the officially-approved cleaning solution can be added to the clean water tank. Do not add any other liquid such as alcohol or disinfectant. The ratio of the cleaning solution to clean water can be checked on the cleaning solution bottle. Keep the cleaning solution out of reach of children.
• Do not use the robot to clean any burning objects. Do not use the robot to pick up flammable or combustible liquids, corrosive gases, or undiluted acids or solvents.
• Do not vacuum hard or sharp objects. Do not use the appliance to pick up objects such as stones, large pieces of paper, or any item that may clog the appliance.
• Plug must be removed from the socket-outlet before cleaning or maintaining the appliance.
• Do not wipe the robot or the base station with a wet cloth or rinse them with any liquid. After cleaning washable parts, fully dry the parts before reinstalling and using them.
• Please use this product in accordance with the instructions in the User Manual. Users are responsible for any loss or damage that arise from improper use of this product.
• Do not use any third-party battery or base station. The robot can only be used with the model RCXE0307/RCXE0307-5 base station.
• Do not attempt to disassemble, repair, or modify the battery or the base station on your own.
• Do not place the base station near a heat source.
• Do not use a wet cloth or wet hands to wipe or clean the base station's charging contacts.
• Do not improperly dispose of old batteries. Unneeded batteries should be discarded at an appropriate recycling facility.
• If the power cord becomes damaged or broken, stop using it immediately and contact after-sales service.
• Make sure the robot is turned off when being transported and kept in its original packaging if possible.
• If the robot will not be used for an extended period of time, fully charge it, then turn it off and store it in a cool, dry place. Recharge the robot at least once every 3 months to avoid over-discharging the battery.

Laser Safety Information

The laser sensor in this product meets the IEC 60825-1:2014/EN 60825-1:2014/A11:2021 Standard for Class 1 laser products. Please avoid direct eye contact with it during use.

CLASS 1 LASER PRODUCT

CONSUMER LASER PRODUCT

ΕΝ 50689:2021

Product Overview

Package Contents

• Robot
• Base Station
• Base Station Ramp
• Extension Plate
• User Manual
• Auto-Detergent Compartment (pre-installed)
• Mop Pad x 2 (pre-installed)
• Mop Pad Holder x 2
• Dust Bag x 2
• Cleaning Tool
• Cleaning Solution (1 pre-installed)
• Power Cord

Other Accessories

Visual representation of various accessories including a mop pad, mop pad holder, dust bag, cleaning tool, and cleaning solution.

Robot

• Spot Cleaning Button: Press to start spot cleaning.
• Power / Clean Button: Press and hold for 3 seconds to turn on or off. Press to start cleaning after the robot is turned on.
• Dock Button: Press to send the robot back to the base station. Press and hold for 3 seconds to disable Child Lock.

Robot and Sensors

Diagram showing the robot's components:

• Cover
• Charging Contacts
• Auto-empty Vent
• LED Auxiliary Light
• Carpet Sensor
• Camera Indicator (lights up when camera is activated)
• AI IR Camera
• AI HD Camera
• Microphone
• LDS Cover
• Laser Distance Sensor (LDS)
• Bumper
• Bumper Window
• 3D Dual-Line Laser Sensors
• Main Brush
• Main Wheel
• MopExtend Assembly
• Dust Box
• Reset Button (Press and hold for 3 seconds to restore to factory settings)
• Wi-Fi Indicator (Slowly blinking: To be connected; Quickly blinking: Connecting; On: Connected)
• Edge Sensor
• Cliff Sensors
• Omnidirectional Wheel
• Brush Guard
• Brush Guard Clips
• Mop Pad Holder
• Mounting Holes
• Dust Box Cover Clip
• Dust Box Clip
• Dust Box Cover
• Auto-empty Vent
• Mop Pad Holder
• Mop Pad

Base Station

Diagram showing the base station's components:

• Upper Cover
• Used Water Tank
• Clean Water Tank
• Dust Tank Cover
• Washboard
• Ramp
• Extension Plate
• Water Tank Clip
• Float Ball
• Auto-Detergent Compartment
• Filter
• Signaling Area
• Auto-empty Vent
• Status Indicator (Solid White: connected to power; Solid Orange: error)
• Dust Bag Slot
• Charging Contacts
• Automatic Water Adding Outlet
• Reserved Slot for Water Tank Clip
• Connecting the Water Hookup Kit for Auto Refilling and Draining
• Power Cord Storage Slot
• Power Port
• Water Pipe
• Filter
• Floater

Preparing Your Home

Before cleaning, please move away unstable, fragile, valuable, or dangerous items, and clean up cables, cloths, toys, hard objects, and sharp objects on the ground to avoid being entangled, scratched, or knocked over by the robot and causing losses.

Before cleaning, place a physical barrier at the edge of the stairs and sofa to ensure the secure and smooth operations of the robot.

Open the door of the room to be cleaned, and put the furniture in its proper place to leave more space.

Note:

• To prevent the robot from not recognizing areas that need to be cleaned, do not stand in front of the robot, threshold, hallway, or narrow places.
• When operating the robot for the first time, follow it around while cleaning to remove any potential obstacles in time.
• The LED auxiliary light will provide auxiliary lighting in dimly lit environments.
• Do not vacuum hard objects like stones, steel balls, and toy parts, or sharp objects like construction waste, broken glass, and nails, otherwise the ground may be scratched.

Before Use

1. Place the Base Station and Connect to an Electrical Outlet
   Place the base station in a location that is as open as possible with a good Wi-Fi signal. Remove any objects that are closer than 1.5 m from the front and 5 cm from either side of the base station. Insert the power cord into the base station and plug it into the socket. Ensure that no objects might block the signaling area. It is recommended to place the base station on tile floors or marble floors to prevent water stains from wetting wood floors or carpets.
2. Install the Ramp Extension Plate
3. Remove Robot Protections and Install the Mop Assembly
4. Connect the Robot to the Base Station
   Press and hold the power button on the robot for 3 seconds to turn it on. Place the robot onto the base station with the mop assembly facing toward the washboard. You will hear a voice notification when the robot successfully connects to the base station. It is recommended to fully charge the robot before its first use. When the robot cannot be turned on after the battery is depleted, manually connect the robot with the station to charge it.
5. Add the Cleaning Solution
   (1) Remove the dust tank cover and pull out the auto-detergent compartment.
   (2) Open the upper lid of the compartment and add the cleaning solution.
   (3) Close the lid of the compartment, put it back into the base station, and then reinstall the dust tank cover. The cleaning solution will be added automatically while working.
   Note: The auto-detergent compartment can be filled up with cleaning solution for use. Do not add any liquid other than the officially-approved cleaning solution to help prevent malfunction.
6. Add Water to the Clean Water Tank
   Take out the clean water tank from the base station and fill it up with clean water. Then install it back into the base station.
   Note: Do not add hot water into the water tank, as this may cause the tank to become deformed.

Connecting with the Dreamehome App

1. Download the Dreamehome App
   Scan the QR code on the robot, or search "Dreamehome" in the app store to download and install the app. (Only 2.4 GHz Wi-Fi is supported)
2. Add Device
   Open the Dreamehome app, tap "+" in the upper right corner, and scan the same QR code on the robot again to add the device. Please follow the prompts to finish the Wi-Fi connection. If you want to reset Wi-Fi, repeat step 2 and then follow the prompts to finish the Wi-Fi connection.
   Note: Due to upgrades in the app software, the actual operations may differ from the directions in this manual. Please follow the instructions based on the current app version.

Wi-Fi Indicator Status:

• Blinking slowly: To be connected
• Blinking quickly: Connecting
• On: Connected

How to Use

Turn On/Off

Press and hold the power button for 3 seconds to turn on the robot. The power indicator should be illuminated. Place the robot onto the base station; the robot should turn on automatically and begin charging. To turn off the robot, move the robot away from the base station and press and hold the power button for 3 seconds.

Fast Mapping

After configuring the network for the first time, follow the instructions in the app to quickly create a map. The robot will start mapping without cleaning. When the robot returns to the base station, the mapping process has been completed and the map will be saved automatically.

Pause/Sleep

When the robot is running, press any button to pause it. If the robot is paused for more than 10 minutes, it automatically enters sleep mode. All indicators on the robot will turn off. Press any button on the robot, or use the app to wake up the robot.

Note: If the robot is paused and placed onto the base station, the current cleaning process will end.

Auto Resume Cleaning

If the battery is too low, the robot will automatically return to the base station to charge. After charging to the appropriate battery level, it will resume unfinished cleaning tasks. (Enable this function in the app.)

Do Not Disturb (DND) Mode

When the robot is set to the Do Not Disturb (DND) mode, it will be prevented from resuming cleaning, and the power indicator goes out. The DND mode is disabled by default at the factory. You can use the app to enable the DND mode or modify the DND period. The DND period is 22:00-8:00 by default.

Note: Scheduled cleaning tasks will be performed as usual during the DND period. The robot will resume cleanup where it left off after the DND period expires.

Spot Cleaning

When the robot is on standby, briefly press the spot cleaning button to enable the spot cleaning mode. In this mode, the robot cleans a square-shaped area of 1.5 x 1.5 meters around it and returns to its starting point once the spot cleaning is completed.

Robot Restarting

If the robot stops responding or cannot be turned off, press and hold the power button for 10 seconds to forcefully turn it off. Then, press and hold the power button for 3 seconds to turn the robot on.

Vacuum and Mop

Note: When using the mop assembly for the first time, the robot performs the "Vacuum and Mop" task by default.

1. Start cleaning
   Press the power button on the robot, or use the app to make the robot start from the base station. The robot will plan the optimal cleaning route and perform the cleaning task based on the created map.
2. Auto mop washing
   When cleaning, the robot will automatically return to the base station to wash mop pads based on the mop pad cleaning frequency specified in the app. The base station will automatically refill the robot's water tank, and the robot will resume cleanup.

Note: To ensure the robot easily returns to the base station after cleaning, it is recommended to make the robot start from the base station. The mop pads will be cleaned before the robot starts mopping; please wait patiently. Do not move the base station, the clean water tank, the used water tank, or the washboard during operation. Hot water cleaning can be enabled in the app for mop pad and washboard base cleaning tasks, which applies to all modes. To prevent scalding, do not touch the water outlet when the function is on.

Automatically empty the dust box and wash and dry the mop pads

After the robot finishes a cleaning task and returns to the base station to charge, the base station will automatically start emptying the dust box. Then, it will wash and dry the mop pads.

Note: If the auto-empty function is turned off in the app, the base station will not automatically empty the dust box. The base station will empty the dust box according to the setting in the app.

Mop after Vacuuming

Enable the mopping after vacuuming function in the app, and the robot will automatically remove the mop assembly on the base station to vacuum the floor. After vacuuming is completed, the robot will return to the base station to install the mop assembly, and the base station will automatically start emptying the dust box. Then, the robot will start mopping after the main brush and side brush are raised.

Vacuum Only

Enable the vacuuming function in the app, and the robot will automatically remove the mop assembly on the base station and start vacuuming.

Mop Only

Enable the mopping function in the app, and the robot will automatically check if the mop assembly is installed on the base station. If not, the robot will install the mop assembly and start mopping after the main brush and side brush are raised.

Clean the used water tank

After the robot has completed its task, please clean the used water tank to prevent any odor.

Routine Maintenance

To keep the robot in good condition, it is recommended to refer to the accessory usage in the app or the following table for routine maintenance.

Note: The replacement frequency will depend on your usage of the robot. If an exception occurs due to special circumstances, the parts should be replaced.

Washboard Base

1. Enable the washboard base cleaning function in the app, and the robot will exit the base station automatically. Take out the washboard and wait for water to fill the washboard base.
2. Use the cleaning tool to clean the washboard base. After a moment, the base station will automatically pump out the used water. Then wipe the washboard base with a soft and dry cloth.
3. Flip the washboard over, remove the roller cover and the roller in turn, and then pull off the end caps of the roller.
4. Remove the hair tangled in the roller, and then reassemble the parts according to corresponding colors, as shown in the figure below.
5. Rinse the washboard with clean water, wipe it clean, and then put it back into the base station downwards in an inclined way.
6. Use the app or briefly press the power button on the robot to make it return to the base station.

Used Water Tank

1. Remove the used water tank, open its cover, and pour out the used water.
2. Rinse the used water tank with clean water, and use the provided cleaning tool to clean the inner wall of the used water tank.

Note: Pulling upwards on the handle will seal the bag to prevent the dust and debris from accidentally falling out.

Note: The float ball in the used water tank is a movable part. Do not apply too much force when cleaning it to avoid damaging it.

Dust Bag

1. Remove the dust tank cover and discard the dust bag.
2. Remove the dust and debris from the filter with a dry cloth.
3. Install a new dust bag.
4. Reinstall the dust tank cover.

Dust Box and Filter

1. Open the robot cover and press the dust box clip to remove the dust box.
2. Open the dust box cover, remove the filter, and then empty the dust box as shown in the diagram.
3. Gently tap the basket of the filter to remove the dirt.
4. Rinse the dust box and filter with water and dry them completely before reinstalling.

Note: Rinse the dust box and filter with clean water only. Do not use any detergent. Use the dust box and filter only when they are completely dry.

Main Brush

1. Press the brush guard clips inwards to remove the brush guard and lift the brush out of the robot.
2. Pull out the brush covers at both ends of the brush as shown in the figure. Use the provided cleaning tool to remove any hair tangled in the brush. Reinstall the brush covers on both ends of the brush, and then reinstall the brush. Press on the brush guard to lock it in place.

Side Brush

Unscrew the side brush with a screwdriver, clean the hair from the brush, and then screw it back on.

Mop Pad Holder

Remove and clean the mop pad holder.

Mop Pad

Remove the mop pad from the mop pad holder to replace it.

Robot Sensors and Charging Contacts

Wipe sensors and charging contacts of the robot by using a soft and dry cloth, as shown in the below figure:

• Omnidirectional Wheel
• Laser Distance Sensor (LDS)
• Cliff Sensors
• Bumper Window
• 3D Dual-Line Laser Sensors
• Edge Sensor
• Bumper
• Carpet Sensor
• Charging Contacts

Note: Use a tool such as a small screwdriver to separate the axle and tire of the omnidirectional wheel. Do not use excessive force. Rinse the omnidirectional wheel under running water and put it back after drying it completely.

Note: A wet cloth can damage sensitive elements within the robot and the base station. Please use a dry cloth for cleaning.

Auto-empty Vents

Clean the auto-empty vents of the robot and the base station with a soft and dry cloth.

Battery

The robot contains a high-performance lithium-ion battery pack. Make sure that the battery remains well-charged for daily use to maintain optimal battery performance. If the robot is not used for an extended period of time, turn it off and put it away. To prevent damage from over-discharging, charge the robot at least once every three months.

Charging Contacts

Clean the charging contacts and the signaling area of the base station with a soft and dry cloth.

Troubleshooting

Specifications

Note: Rated Power (during hot water cleaning) is determined by the power value during the representative period (water temperature 25°C). Rated Power (during charging and drying) is determined by the power value during the full load period.

Under normal use conditions, this equipment should be kept a separation distance of at least 20 cm between the antenna and the body of the user.

For more support, contact us via https://global.dreametech.com