User Manual for AJAX models including: 10306, Transmitter, 10306 Transmitter
Index of /manuals/2022
Transmitter is a module for connecting third-party detectors to Ajax security system. It transmits alarms and warns about the activation of the external.
File Info : application/pdf, 13 Pages, 462.24KB
DocumentDocumentUpdated May 25, 2021 Transmitter is a module for connecting third-party detectors to Ajax security system. It transmits alarms and warns about the activation of the external detector tamper and it is equipped with own accelerometer, which protects it from dismounting. It runs on batteries and can supply power to the connected detector. Transmitter operates within the Ajax security system, by connecting via the protected protocol to the . It is not intended to use the device in third-party systems. Not compatible with the or The communication range can be up to 1,600 meters provided that there are no obstacles and the case is removed. Transmitter is set up via a for iOS and Android based 1. QR code with the device registration key. 2. Batteries contacts. 3. LED indicator. 4. ON/OFF button. 5. Terminals for detector power supply, alarm and tamper signals. Transmitter is designed to connect third-party wired sensors and devices to the Ajax security system. The integration module receives information about alarms and tamper activation through the wires connected to the clamps. Transmitter can be used to connect panic and medical buttons, indoor and outdoor motion detectors, as well as opening, vibration, breaking, fire, gas, leakage and others wired detectors. The type of alarm is indicated in the settings of the Transmitter. The text of notifications about alarms and events of the connected device, as well as event (CMS) depend on the selected type. A total of 5 types of devices are available: Type Icon Intrusion alarm Fire alarm Medical alarm Panic button Gas concentration alarm A separate pair of terminals ensures power supply to the external detector from the module batteries with 3.3 V. 1. Following the hub instruction recommendations, install the on your smartphone. Create an account, add the hub to the application, and create at least one room. 2. Go to the Ajax application. 3. Switch on the hub and check the internet connection (via Ethernet cable and/or GSM network). 4. Ensure that the hub is disarmed and does not start updates by checking its status in the mobile application. Only users with administrative privileges can add the device to the hub 1. Select the Add Device option in the Ajax application. 2. Name the device, scan/write manually the QR Code (located on the body and packaging), and select the location room. 3. Select Add -- the countdown will begin. 4. Switch on the device (by pressing on/off button for 3 seconds). For the detection and interfacing to occur, the device should be located within the coverage area of the wireless network of the hub (at a single protected object). Request for connection to the hub is transmitted for a short time at the time of switching on the device. If the connection to the Ajax hub failed, the Transmitter will switch off after 6 seconds. You may repeat the connection attempt then. The Transmitter connected to the hub will appear in the list of devices of the hub in the application. Update of device statuses in the list depends on the device inquiry time set in the hub settings, with the default value 36 seconds. 1. Devices 2. Transmitter Parameter Temperature Jeweller Signal Strength Battery Charge Value Temperature of the device. Measured on the processor and changes gradually Signal strength between the hub and the device Battery level of the device. Displayed as a percentage Connection Always Active Alert if Moved Temporary Deactivation Firmware Device ID 1. Devices Connection status between the hub and the Transmitter If active, the device is always in an armed mode It turns on the Transmitter accelerometer, detecting device movement Shows the status of the device temporary deactivation function: No -- the device operates normally and transmits all events. Lid only -- the hub administrator has disabled notifications about triggering on the device body. Entirely -- the device is completely excluded from the system operation by the hub administrator. The device does not follow system commands and does not report alarms or other events. By number of alarms -- the device is automatically disabled by the system when the number of alarms is exceeded (specified in the settings for Devices Auto Deactivation). The feature is configured in the Ajax PRO app. By timer -- the device is automatically disabled by the system when the recovery timer expires (specified in the settings for Devices Auto Deactivation). The feature is configured in the Ajax PRO app. Detector firmware version Device identifier First field Room External Detector Contact Status External Detector Type Tamper status Alarm Type Always Active Device name, can be edited Selecting the virtual room to which the device is assigned Selection of the external detector normal status: Normally closed (NC) Normally opened (NO) Selection of the external detector type: Pulse Bistable Selection of the normal tamper mod for an external detector: Normally closed (NC) Normally opened (NO) Select alarm type of connected device: Intrusion Fire Medical help Panic button Gas The text of SMS and notifications in events feed, as well as the code transmitted to the security company's console, depends on the selected type of alarms When the mode is active, the Transmitter transmits alarms even when the system is disarmed Detector Power Supply Arm in Night Mode Alert with a siren if an alarm is detected Jeweller Signal Strength Test Attenuation Test User Guide Temporary deactivation movement Turning the power on in 3.3 V external detector: Disabled if disarmed Always disabled Always enabled If active, the device will switch to armed mode when using night mode If active, added to the system are activated if an alarm is detected Switches the device to the signal strength test mode Switches the device to the signal fade test mode (available in detectors with firmware version 3.50 and later) Opens the device User Guide Two options are available: Entirely -- the device will not execute system commands or run automation scenarios. The system will ignore device alarms and notifications Lid only -- messages about triggering the tamper button of the device are ignored The system can also automatically deactivate devices when the set number of alarms is exceeded or when the recovery timer expires. The type (mode) of the external detector that can be bistable or pulse. The tamper mode, which can be normally closed or normally open. The accelerometer-triggered alarm -- you can turn this signal off or on. Select the power mode for the external detector: Turned off when the hub is disarmed -- the module stops powering the external detector upon disarming and does not process signals from the ALARM terminal. When arming the detector, the power supply resumes, but the alarm signals are ignored for the first 8 seconds. Always disabled -- the Transmitter saves energy by turning off the power of the external detector. The signals from the ALARM terminal are processed both in the pulse and bistable modes. Always active -- this mode should be used if there are any problems in the "Turned off when the hub is disarmed". When the security system is armed, signals from the ALARM terminal are processed no more than once in three minutes in the pulse mode. If the bistable mode is selected, such signals are processed instantly. If the "Always active" operating mode is selected for the module, the external detector is powered only in the "Always active" or the "Turned off when the hub disarmed" mode, regardless of the security system status. Event The Module is switched on and registered Registration failed Indication The LED lights up when the ON button is briefly pressed. LED blinks for 4 seconds with an interval of 1 second, then blinks 3 times rapidly (and The Ajax security system allows conducting tests for checking the functionality of connected devices. The tests do not start straight away but within a period of 36 seconds when using the standard settings. The test time start depends on the settings of the detector scanning period (the paragraph on "Jeweller" settings in hub settings). Location of the Transmitter determines its remoteness from the hub and presence of any obstacles between the devices hindering the radio signal transmission: walls, inserted floors, large-size objects located within the room. Check the signal strength level at the installation location If the signal level is one division, we cannot guarantee stable operation of the security system. Take possible measures to improve the quality of the signal! As a minimum, move the device -- even 20 cm shift can significantly improve the quality of reception. If, after moving, the device still has a low or unstable signal strength, use a . The maximum cable length for connecting the sensor is 150 m (24 AWG twisted pair). The value may vary when using different type of cable. The function of the Transmitter's terminals + -- -- power supply output (3.3 V) ALARM -- alarm terminals TAMP -- tamper terminals IMPORTANT! Do not connect external power to the Transmitter's power outputs. This may damage the device 2. Secure the Transmitter in the case. Plastic bars are included in the installation kit. It is recommendable to install the Transmitter on them. The device does not require maintenance when mounted in the housing of a wired sensor. Connecting a detector Mode for processing alarm signals from the detector Power Capability to power the connected detector Protection from dismounting Frequency band Compatibility Maximum RF output power Modulation Communication range Ping interval for the connection with the receiver Operating temperature Operating humidity ALARM and TAMPER (NO/NC) terminals Pulse or Bistable 3 × CR123A, 3V batteries Yes, 3.3V Accelerometer 868.0868.6 MHz or 868.7 869.2 MHz, depends on sales region Operates only with all Ajax , and Up to 20 mW GFSK Up to 1,600 m (any obstacles absent) 12300 sec From 25° to +50° Up to 75% 1. Transmitter 2. Battery CR123A -- 3 pcs 3. Installation kit 4. Quick Start Guide Warranty for the "AJAX SYSTEMS MANUFACTURING" LIMITED LIABILITY COMPANY products is valid for 2 years after the purchase and does not apply to the pre-installed battery. If the device does not work correctly, you should first contact the support service -- in half of the cases, technical issues can be solved remotely! Technical support:Acrobat Distiller 21.0 (Windows)
