Intelligent Toilet Installation
Tools required for installation
Required tools
Required tools for installation. Please have these tools prepared prior to installation.
- ?️[Drill] (Diameter 0.24 inches)
- ?[Silicone gun]
- ?[Teflon tape]
- ?[Knife]
- ?️[Marking pen]
- ?[Screwdriver]
- ?[Measuring tape]
- ☕[Measuring cup]
[Spanner] (0.91-0.98 inches, size may vary for different pipes)
Before you Install
Water pressure check, dimensional drawing
Confirmation of water pressure
The minimum dynamic operating water pressure is 35 psi, and the maximum static water pressure is 108 psi.
Determination method for minimum water flow
Open the angle valve for water supply. Ensuring a flow of water at least 5.2L/20s, can meet the minimum flushing requirements. This data needs to be measured from the valve of the toilet.
Diagram showing a water valve connected to a measuring cup, with a stopwatch used to time the flow. The process aims to measure a flow of at least 5.2 liters in 20 seconds to meet minimum flushing requirements.
If the above conditions cannot be met, the best flushing effect cannot be achieved and an additional booster pump is required to increase the pressure. (Tools: stopwatch, measuring cup.)
Confirm dimensions of product with installation space
Please ensure that the distance between the center point of the sewage outlet and the wall is not less than 12 inches!
Diagram illustrating the toilet's dimensions relative to a wall. It shows a side view, front view, and top view, with key measurements including a 'rough-in' distance of 12 inches from the wall to the drain center, and overall dimensions like 15.94 inches (width), 18.5 inches (depth), 15.75 inches (height from floor to seat), and 27.17 inches (total height).
Item list (Confirm that all below items are inside the box)
- Intelligent toilet (1 set)
- T-valve (1 piece)
- Two AAA Batteries
- Remote control set (1 set)
- Wax Ring (1 piece)
- Installation Book & User Manual
- Sealing Flange (includes 1 holder, 2 screws)
- Mounting accessory kit (2 pieces)
- Mounting Template
Please confirm all the aforementioned items are inside the package. If there are any omissions, please contact our customer service. The flange and wax ring we provide are for backup only. You can also use your existing flange. If your flange is lower than the ground, we recommend purchasing thicker wax rings to achieve strict sealing.
Installing your product
Install your unit using the following steps
1 Open the box right side up
Remove the accessories first, then remove the unit from the top, as shown in the diagrams below.
Diagram illustrating the unboxing process: a cardboard box is opened, and the smart toilet unit is lifted out from the top.
2 Mark your drainage hole with a cross
Cardboard installation
- Align cardboard with the centerline of drain outlet;
- Draw contour line according to cardboard;
Diagram showing how to use the cardboard template to mark the drain outlet on the floor. The template is aligned with the drain centerline, and a contour line is drawn around it. A minimum distance of 12 inches (≥12in) from the wall to the drain outlet is indicated.
3 Mounting bracket installation
Assemble the mounting bracket with bolts and then install them to the pre-installed flange plate on the ground and lock tight with nuts.
Diagram illustrating the mounting bracket assembly. It shows a mounting bracket, a washer, a nut, and a bolt, indicating how they are put together and attached to the pre-installed flange plate on the floor.
4 Install the ceramic body, water supply hose, T-valve
- Place the wax ring on the drain hole at the bottom of the ceramic.
- Install sealing flange into drain outlet.
- Install ceramic toilet on corresponding position according to contour line.
Diagram showing the ceramic toilet being placed over the drain outlet, with the sealing flange installed in the outlet. The toilet drain outlet is visible at the bottom. Tips: The toilet is heavy, and it needs to open the seat cover to carry it by two people.
- Put the screw through the fixing sleeve and then install it through the holes (on both sides of the toilet ceramic) to the mounting bracket on the ground, and lock tight with a tool.
- Put the decorative cap on the fixing sleeve.
Diagram showing the installation of the fixing sleeve and screw to secure the toilet to the mounting bracket, followed by placing a decorative cap over the screw head.
- Attach the flush water hose to the T-valve and tighten.
Diagram showing the flush water hose connected to the T-valve and the water supply.
- Attach the clean water hose to the T-valve and tighten.
Diagram showing the clean water hose connected to the T-valve and the water supply.
- Connect the T-valve to the water supply and tighten. Use gasket to prevent water leakage.
Diagram showing the T-valve connected to the water supply, with the water outlet for the toilet hose visible.
- Finish installation.
5 Installing the remote
- Drill two 6mm (0.24 inch) diameter holes on the wall (about 1.77 in deep)
- Knock the anchors into the hole with a hammer.
- Secure the holder with anchors.
- Use the screws to secure the holder to the wall.
- Remove the battery cover from the backside of the remote to install batteries.
- Once finished, remote is ready to be placed in its holder.
Detailed steps shown in the diagram below:
Diagram illustrating the steps for installing the remote control holder: drilling holes, inserting anchors, attaching the holder with screws, removing the battery cover from the remote, installing batteries, and placing the remote into its holder. Dimensions for drilling are shown: 6mm (0.24 inch) diameter holes, approximately 1.77 inches deep, and the holder should be placed at least 17.7 inches above the floor.
※Please use proper mounting tools for special wall surfaces (such as wood, HDF, etc.)
※The remote control holder should be installed away from the bidet's spray trajectory.
※The remote control holder should be installed within reach when seated on unit.
Make sure there is nothing to block the transmission between the toilet and its remote.
6 Installing and replacing the battery box
Install and replace the emergency flushing battery
- Reach into the bottom of the toilet cover and lift the cover upward firmly;
- Remove the battery cover by unscrewing the screw with a crosshead screwdriver;
- Replace the new battery, shut the battery cover, and tighten the screw with a crosshead screwdriver;
- Place the toilet cover to the flat position and press down to fix the cover.
Diagram showing how to access the emergency flushing battery box located at the bottom of the toilet cover. A spare battery is also depicted.
※Please confirm the battery's positive and negative poles. Please do not charge, disassemble, fire the battery, or mix with used batteries or different kinds of batteries to avoid liquid leakage or explosion.
※The battery box has a moisture-proof function. Please ensure that the set screws are screwed in place to achieve a good seal effect.
※If the battery needs to be replaced, it is recommended to contact your local dealer to have it replaced by specialized personnel.
7 Testing water flow
- Open the water supply angle valve to maximum as shown in the figure.
- Confirm various connecting parts are not water leaking. In case of water leaking, unfasten the nuts again and install them again.
Diagram showing the water supply angle valve being opened to its maximum position.
8 Connecting power
- Connect to the grounding.
- Plug in AC 120V power plug.
Diagram illustrating the power connection: a 120V AC plug is shown, along with indicators for checking if the power light is on and confirming the toilet is powered by pressing a side button. An 'occupied sensor point' is also indicated.
(1) Check to see if the power light is on.
(2) Press the side button to confirm that the toilet is powered on.
(3) Check to see if the power is on.
Testing the product
(Test whether the functions of the buttons on the remote control and the button on the side of the body are normal)
Are all the functions working properly?
- Rear Wash, Front Wash (Including water pressure & nozzle position adjustment), Heated Dryer, Water & Seat temperature Adjustment, Nozzle cleaning, Remote control.
- All functions listed above should be tested.
Checking Rear Wash
Please use your hand to hold the seat sensor area, press the side "⚙️" button or press the "Rear Wash" button on the remote control, and use your hand to cover the front of the washer to block the flow of wash water to avoid spraying water on your body or clothing.
Diagram for 'Checking Rear Wash' shows a hand positioned to block the seat sensor area while the wash function is activated, to prevent water spray.
Matching your remote control code
※When the product leaves the factory, the remote control and the product are connected, if the remote control went failure, please re-connect the code as following methods.
- Unplug the product's plug, press the stop key for few seconds until the level light is flickered.
- Plug the attaching plug when the remote control get closer to the product.
- The level light stops flickering, and then it is lighted on. All the level light (red) is lighted on.
- At the time, the remote control and product is re-connected.
Diagram illustrating the remote control re-pairing process. It involves unplugging the toilet, pressing and holding a 'stop' button until a level light flickers, then plugging the toilet back in while the remote is near, and waiting for the level light to turn solid, indicating successful re-connection.
Contact Information
The Quickest Solution when you have questions about installation: Take photos of your installation environment and send an email to: support@eplo.com
EPLO has experienced Technical Support to provide the fastest solutions.
