PEAK Rock Slider Installation Manual

Important Notice

Rock Slider installations should only be done by a qualified person and it is the responsibility of this person to ensure correct fitment.

Disclaimer

Important Notice Regarding Installation and Warranty

Thank you for choosing the PEAK ROCK SLIDER. This manual contains essential instructions for proper installation and usage. It is of utmost importance that you carefully read and follow these guidelines. Additionally, PEAK wants to emphasize the critical role of experience and expertise in installing this Rock Slider correctly.

Experienced Installation

Installing a Rock Slider requires a certain level of technical skill and knowledge. PEAK strongly recommends that the installation be carried out by a qualified professional who has experience with vehicle modifications and Rock Slider installation. Incorrect installation can lead to safety hazards and vehicle damage.

Voidance of Warranty

Please be aware that improper installation, use of unauthorized parts, or installation by unqualified individuals can void the warranty of the Rock Slider and associated components. Any damage resulting from improper installation or use will not be covered under warranty.

Liability and Responsibility

PEAK, the manufacturer, cannot be held responsible for any damage, injury, or loss caused by improper installation, modification, or usage of this product. It is the responsibility of the installer and the vehicle owner to ensure that installation is conducted according to the instructions provided in this manual.

Safety First

Your safety and the safety of others on the road are paramount. If you are not confident in your ability to install the Rock Slider correctly, or if you lack experience in vehicle modifications, PEAK strongly recommends seeking assistance from a certified professional.

Professional Installation Recommended

To ensure optimal performance, safety, and warranty coverage, PEAK strongly advises having your rock slider installed by a qualified technician who is knowledgeable about Rock Slider installations and adheres to industry standards.

By proceeding with the installation of this Rock Slider, you acknowledge that you have read and understood this disclaimer, and you accept full responsibility for the installation process and its outcomes.

If you have any questions or concerns, please contact PEAK customer support team before proceeding.

Thank you for choosing PEAK's product, and PEAK appreciates your commitment to safety and quality installation.

Safety Personal Protective Equipment (PPE)

• [ear protection]: Always wear ear protection when using power tools.
• [safety glasses]: Ensure eye protection is always worn when cutting or drilling.
• [manual handling]: Do not attempt to lift bar assemblies or rock sliders on your own. Always use two people to lift or use mechanical lifting aid such as a hydraulic lifting trolley.
• [vehicle support warning]: Always ensure the vehicle is properly supported when working on it. Do not attempt to fit products whilst suspension work is being carried out. Do not work under a vehicle supported only by a jack.

Tools Required

• Ratchet
• Socket Set
• Spanner Set
• Scissors

Supplied Hardware

The following components are supplied with the PEAK Rock Slider kit:

• Item 1: Rock Slider LH (Left Hand) x 01.
  [Diagram: Left side rock slider with mounting brackets.]
• Item 2: Rock Slider RH (Right Hand) x 01.
  [Diagram: Right side rock slider with mounting brackets.]
• Item 3: Rubber Insulator - L70 mm. x 02.
  [Diagram: Rubber insulator piece.]
• Item 4: Rubber Insulator - L80 mm. x 02.
  [Diagram: Rubber insulator piece.]
• Item 5: Rubber Insulator - L90 mm. x 02.
  [Diagram: Rubber insulator piece.]
• Item 6: Hex Bolt M12 x 120 mm. x 02.
  [Diagram: Two hex bolts.]
• Item 7: Hex Bolt M12 x 150 mm. x 04.
  [Diagram: Four hex bolts.]
• Item 8: Spring Washer M12 x 06.
  [Diagram: Six spring washers.]
• Item 9: Washer M12 x 12.
  [Diagram: Twelve flat washers.]
• Item 10: Hex Nut M12 x 06.
  [Diagram: Six hex nuts.]
• Item 11: Cable Ties x 6.
  [Diagram: Six cable ties.]

Installation Instructions

Part 1: Fitting on the Left and Right Side

Step 1: For attaching the rock slider, the front, middle, and rear brackets need to be fixed to the vehicle's chassis so that bolts can be installed and tightened.

[Diagram: Underside of vehicle chassis showing mounting points for LH and RH rock sliders. Red arrows indicate bracket attachment points.]

Step 2: Take note of the bracket positions and factory brake/service lines. If needed, unclip them from the mounting points to ensure the rock slider mounting bolts can pass freely underneath.

[Diagram: Rock slider brackets positioned near vehicle chassis. Red arrows indicate unclipping brake/service lines if necessary.]

Step 3: Securing Brackets

Step 3.1 (Front Bracket): Use M12 x 150 mm. bolts to tighten the front bracket both LH and RH.

[Diagram: Close-up of a front bracket being attached to the chassis using an M12 x 150 mm bolt and washers. Red arrows show tightening direction.]

Step 3.2 (Middle Bracket): Use M12 x 150 mm. bolts to tighten the middle bracket both LH and RH.

[Diagram: Close-up of a middle bracket being attached to the chassis using an M12 x 150 mm bolt and washers. Red arrows show tightening direction.]

Step 3.3 (Rear Bracket): Use M12 x 120 mm. bolts to tighten the rear bracket both LH and RH.

[Diagram: Close-up of a rear bracket being attached to the chassis using an M12 x 120 mm bolt and washers. Red arrows show tightening direction.]

Step 4: Applying Rubber Insulators

After tightening the bolts, apply the above specified length rubber insulator over the bolts.

[Diagram: Rock slider mounted on vehicle chassis. Rubber insulators of specified lengths (L70 mm, L80 mm, L90 mm) are shown being placed over the bolts on the front, middle, and rear brackets.]

Step 5: Securing Wiring

Use cable ties to bundle the wires together and then use scissors to cut off the excess both LH and RH.

[Diagram: Wiring near the vehicle chassis. A cable tie is shown bundling wires, with scissors cutting the excess tie.]

Important Check: [Warning symbol] Check and inspect the rock slider to ensure that it's installed correctly and securely tightened.