36" LED Mirror

Key Features

• ⬜️ Frameless, modern design
• ? Energy-saving LED illumination
• ? Integrated dimming functionality for customizable brightness
• ? Built-in anti-fog technology for a clear reflection
• ? Convenient 3x magnifier

Product Features & Dimensions

Detailed view of the 36" LED Mirror.

Dimensions:

• Main Mirror Size: 36 inches
• Overall Dimensions: 900mm (width) x 750mm (height) x 30mm (depth)

Technical Drawings Description:

Front View: Shows the rectangular mirror with a touch switch and a 3x magnifier integrated on the right side. Dimensions indicate 900mm width and 750mm height.

Side View: Depicts the mirror's profile, showing a depth of 20mm, with matte acrylic and an aluminum frame.

Back View: Illustrates the rear of the mirror, including the aluminum frame, magnifying glass box with a light strip, and electrical connections.

Key Features Summary:

• 36" main mirror size
• Built-in 3X Magnifying Mirror
• Advanced Anti-Fog Technology
• Integrated Dimming Control
• Energy-Saving LED Illumination
• Frameless Modern Design

Quick Start Guide

1. Turn OFF power at the breaker (verify with tester).
2. Locate studs and mark centerline.
3. Install hanging bar/brackets level.
4. Make hard-wired electrical connections.
5. Hang mirror; use lock-catch for horizontal mount.
6. Restore power; test touch sensors (light, anti-fog).

Safety & Compliance

• Installation by a licensed electrician only.
• Connect to a GFCI-protected, properly grounded circuit (120 V~ 60 Hz).
• Do not connect to any wall dimmer (ELV/triac). Use a standard ON/OFF switch if desired; dimming happens on the mirror.
• Two-person lift required; use PPE (Personal Protective Equipment).
• Mount into wall studs whenever possible; use proper anchors for wall type.

Safety Icons:

• ? GFCI Protected
• ? No wall dimmer
• ? Ground properly
• ?‍?‍? Two-person lift
• ⛑️ PPE

⚠️ DANGER

What's in the Box & Tools Needed

Included:

• ? Mirror assembly
• ? Hanging bar
• ? Wall screws (x2)
• ⚓️ Anchors (x2)

Tools Needed:

• ? Band tap (Tape measure)
• ⚖️ Level
• ✏️ Pencil
• ⛑️ PPE
• ?️ Drill bits
• ?? Electronic drill
• ➕ Cross screwdriver
• ? Stud finder

Hardware Instructions

Warning: Manufacturer's warranty shall be void if product is not installed by a licensed professional.

Prior to commencing installation, please ensure the following:

• The wall where the product is being installed is able to support the weight of the product.
• The main electrical supply has been powered OFF to complete installation.

IMPORTANT: Wiring Instructions for Canada & USA

This fixture's wiring colors may not align with standard North American guidelines. For a safe installation, please re-identify the fixture wires with electrical tape as follows:

• LIVE: Wrap black tape on the fixture's White wire. Connect this to your home's Black (Live) wire.
• NEUTRAL: Wrap white tape on the fixture's Black wire. Connect this to your home's White (Neutral) wire.
• GROUND: Connect the Green wire to your home's Green or Bare Copper ground wire.

Please consult a licensed electrician if you are unsure.

Wiring Diagrams Description:

Wires Diagram: Shows three wires: Live wire (White), Neutral wire (Black), and Ground wire (Green).

Connectors Diagram: Illustrates the connections: Live to Live, Neutral to Neutral, Ground to Ground.

Important Notes:

• Hard-wire only. Do not attach a cord-and-plug.
• Use listed wire connectors; make all splices inside approved boxes.
• Do not use a wall dimmer. Use a standard ON/OFF switch if wall control is required.

Wall Mounting Instructions

1. Measure the distance of the mounting hole. Drill holes with a suitable sized drill.

   [Diagram: Shows measuring a distance and drilling holes on a wall.]

2. Insert the anchor and mounting screw into the wall.

   [Diagram: Shows inserting an anchor and screw into a drilled hole in the wall.]

3. Connect the mirror wires with your main wires and hang the mounting hole to the screw on the wall.

   [Diagram: Shows connecting wires and hanging the mirror onto a wall-mounted screw/bracket.]

4. Peel off protective film and clean the mirror with a damp cloth.

   [Diagram: Shows a clean mirror with protective film removed.]

Operation & Features

Mirror Light / Defogging Use

Short touch the Touch sensor to turn on/off the mirror light, or defogging function.

[Diagram: Shows a hand touching a sensor on the mirror to activate light/defog.]

Dimming Light Use

Long touch the Touch sensor to dim the mirror light.

Available dimming levels: 15%, 50%, and 100%.

[Diagram: Shows a hand holding a touch on a sensor to adjust brightness.]

Care & Cleaning and Troubleshooting

Care & Cleaning

• Wipe with a soft, lint-free cloth; use a mild non-ammonia cleaner.
• Do not use abrasives, pads, acids, or solvents.
• Apply cleaner to cloth, not directly on sensor areas.

Troubleshooting (Quick Fixes)

• ?❌ No light at install: Confirm breaker ON, correct wiring, internal quick-connects fully seated.
• ?❌ Touch unresponsive: Power cycle at breaker for 60 seconds; clean/dry glass over sensors.
• ? Buzz/Hum: Ensure unit is not on a wall dimmer; verify solid ground.
• ♨️❌ Anti-fog not warming: Ensure left sensor is ON; feature auto-turns-off after 1 hour.