USER GUIDE
SAFETY INSTRUCTIONS
This product may be used for domestic use only and may not be used for commercial or industrial purposes. This product should also not be used outdoors or in wet conditions.
? When using the product, please ensure that it is used in a safe environment and under the supervision of someone who understands the safe use of the product and its hazards. Never allow children or people with impaired thinking skills to use this product alone.
? Please take extra care when using this product near children and pets. Do not let children or pets play with this product.
Dispose of all packaging materials properly. Keep away from children and pets.
Do not use or store this product in wet places such as outdoors or in bathrooms.
Please do not touch the power plug or this product with wet hands.
Do not use this product to pick up wet hair or liquids.
Please do not use this product if the power cord or power plug is damaged.
Please do not disassemble this product by yourself. The wrong way of assembly may lead to electric shock or fire. Please contact AIRROBO when you need repair services.
Please do not use this product to pick up flammable or combustible liquids such as gasoline. Do not use this product to pick up high temperature or highly flammable objects such as cigarettes, matches, hot soot, etc., otherwise it may cause fire and explosion.
Do not use the product in or near environments where flammable or combustible gases or liquids are present.
Please do not pull the power cord. Please do not put heavy objects on the top of the product.
Please do not put your fingers or other body parts into the suction port, please do not put foreign objects such as plastic bags into the suction port to avoid injury or product failure.
Do not use chemical products with aromatics and fragrances on the filter, otherwise there is a risk of fire.
Please keep the dust cup and filter cleaned regularly. Use of dust cup and filter in filthy conditions may cause product failure or accidents.
? When cleaning and maintaining the product, be sure to disconnect the power supply and unplug the power cord before doing so. Otherwise, there is a risk of electric shock, accidents and injuries.
This product has a function to stop operation when the temperature rises abnormally. If the motor heats up abnormally, be sure to stop the operation immediately. If the suction port is blocked, stop the operation, take out the dust cup, make sure the suction port and filter are clean, and restart it again after 60 minutes.
Be sure to install and use the filter correctly. Using this product with the filter removed may cause product failure.
Please pay attention to the sharp edge of the accessories, beware of scratches. The blade has been sharpened for some of the accessories (such as the deshedding tool and electric clipper) due to functional needs. Please pay attention to safety when using the product.
Note: The flexible hose contains electrical wiring and should not be used to pick up water or be immersed in water for cleaning. Check the hose regularly and prohibit its use if it is damaged.
In the box
Vacuum Device
Vacuum Device *1 (One HEPA filter and one sponge filter have been pre-installed)
[Diagram: A line drawing of the AIRROBO PG100 vacuum device.]
Accessories
- Flexible Hose *1 [Diagram: A flexible hose with connectors.]
- Deshedding Brush *1 [Diagram: A brush head designed for deshedding.]
- Grooming Brush *1 [Diagram: A brush head for general grooming.]
- Electric Clipper *1 [Diagram: An electric clipper attachment.]
- Guide Comb *3 [Diagram: Three guide combs of different sizes.]
- Cleaning Brush *1 [Diagram: A small brush for cleaning.]
- Crevice Tool *1 [Diagram: A narrow nozzle for cleaning crevices.]
- Storage Bag *1 [Diagram: A fabric bag for storage.]
- User Manual *1 [Diagram: A booklet labeled "User Manual".]
- Warranty Card *1 [Diagram: A card labeled "Warranty Card".]
Product Overview
Operation Panel:
[Diagram: Top view of the vacuum device showing the operation panel.]
The operation panel features:
- Power button: Powers the device on/off.
- MIN key: Lowers the suction level.
- MAX key: Raises the suction level.
Indicators: A total of three levels indicating low, medium, and high suction power.
Dust Cup: The container for collecting debris.
Flexible Hose Connector: The port where the flexible hose attaches to the device.
How to use
- Connect the accessory and the vacuum device through the flexible hose. Please be careful to install the connectors at both ends of the hose tightly to avoid air leakage.
[Diagram: Shows the flexible hose being connected to the vacuum device and an accessory. Numbered steps 1-5 illustrate the connection process.]
- Plug the power cord of the vacuum device into a power socket.
- Turn on the power switch of the vacuum device. Select a suction level as needed. There are three different suction levels: low, medium, and high. Vacuum cleaners produce noise, so it is recommended that you start with the lowest suction level at the beginning, soothing your pet during use to avoid stress or fear. After your pet has adapted, adjust the suction power to a higher level as needed.
Note: Pay attention to the sharp edge of the accessories when using, beware of cuts.
How to use accessories
Grooming Brush
It cleans the pet's body of floating hair and the waste inside the coat, making the coat smoother and fluffier.
[Diagram: Shows the grooming brush being used on a dog, with an inset showing how to press a button to clean the brush.] Press the button to clean the hair on the brush.
Cleaning Brush
It can be used to clean pet hair or dust from clothes, sofas, or carpets, and can also be used to clean pet's paws.
[Diagram: Shows the cleaning brush being used on clothes and a pet's paw.]
Deshedding Brush
It can be used to manually trim and clean up your pet's matted, overgrown hair.
[Diagram: Shows the deshedding brush being used on a cat, with an inset showing how to press a button to clean the brush.] Press the button to clean the hair on the brush.
Note: Pay attention to the blade and sharp edge when using. Do not use excessive force to avoid causing scratches on your pet's skin.
Crevice Tool
It can be used to clean pet hair or dust that falls in the cracks of sofas and beds.
[Diagram: Shows the crevice tool being used to clean between sofa cushions.]
Electric Clipper
It is used to finely trim pet hair and draw it into the dust cup. Trimming and grooming and vacuuming are solved at once.
[Diagram: Shows the electric clipper attachment being used on a dog's back.]
There is an independent power switch button on the electric clipper. After the vacuum device is turned on, you can control the electric clipper separately by this power button, which is more convenient to use.
[Diagram: Close-up of the electric clipper showing its power switch.]
Note: The clipper is for trimming pet hair only. Please be careful with the soft parts of your pet's skin and do not use excessive force to avoid causing scratches on your pet's skin.
Guide Combs
According to the different length of the pet's hair and different trimming and grooming needs, guide combs with different lengths can be replaced and used together with the electric clipper. There are 3 guide combs in the package, and each guide comb can meet the needs of two different sizes. Simply reverse the mounting direction of the guide comb when using.
- 3mm & 6mm (1/8 & 1/4 inch) [Diagram: Shows the 3mm and 6mm guide combs.]
- 9mm & 12mm (3/8 & 1/2 inch) [Diagram: Shows the 9mm and 12mm guide combs.]
- 18mm & 24mm (3/4 & 1 inch) [Diagram: Shows the 18mm and 24mm guide combs.]
[Diagram: Illustrates reversing the mounting direction of a guide comb on the electric clipper.]
Note: Please keep the guide combs in a safe place when not in use to prevent loss.
How to maintain
Dust cup maintenance
- Lift and remove the dust cup slightly in the direction of the arrow. [Diagram: Shows the dust cup being lifted with an upward arrow.]
- Push the snap to open the dust cup and empty it. [Diagram: Shows the dust cup opening and being emptied.]
- Install the dust cup in the direction of the arrow. [Diagram: Shows the dust cup being reinserted with a downward arrow.]
Notes:
Be careful when removing and installing the dust cup.
If the removed dust cup is cleaned by water, remember to wait until the dust cup is completely dry before installing it to prevent electric shock or damage caused by water in the motor.
HEPA filter maintenance
- Remove the dust cup and take out the HEPA filter. [Diagram: Shows dust cup removal and HEPA filter extraction.]
- Please wash it with tap water and drain the water after washing. [Diagram: Shows the HEPA filter being washed under a tap and water draining.]
- Place it in a well-ventilated place for at least 24 hours and leave it to dry sufficiently. [Diagram: Shows the HEPA filter drying in sunlight and a clock indicating 24 hours.]
- Install the HEPA filter back in place after it is completely dry. Be sure to install the HEPA filter before using the vacuum device. [Diagram: Shows the HEPA filter being installed correctly (check mark) and incorrectly (cross mark).]
Notes:
Please clean the HEPA filter regularly according to the frequency of use and dirt condition.
Remember to disconnect the power supply and unplug it from the socket when cleaning.
Be sure to install the HEPA filter after it is completely dry, otherwise it may cause electric shock and product failure.
Sponge filter maintenance
- Remove the dust cup and take out the sponge filter. [Diagram: Shows dust cup removal and sponge filter extraction.]
- Please wash it with tap water and drain the water after washing. [Diagram: Shows the sponge filter being washed under a tap and water draining.]
- Place it in a well-ventilated place for at least 24 hours and leave it to dry sufficiently. [Diagram: Shows the sponge filter drying in sunlight and a clock indicating 24 hours.]
- Install the sponge filter back in place after it is completely dry. Be sure to install the sponge filter before using the vacuum device. [Diagram: Shows the sponge filter being installed correctly (check mark) and incorrectly (cross mark).]
Notes:
Please clean the sponge filter regularly according to the frequency of use and dirt condition.
Remember to disconnect the power supply and unplug it from the socket when cleaning.
Be sure to install the sponge filter after it is completely dry, otherwise it may cause electric shock and product failure.
Electric clipper maintenance
- Remove the cutter head in the direction shown by the arrow. [Diagram: Shows the electric clipper head being removed with a directional arrow.] Note: The cutter head is very sharp, please be careful not to cut your hand.
- The suction port of the flexible hose can be used to pick up the hair and dust from the cutter head and cutter holder. [Diagram: Shows the flexible hose suction port cleaning the clipper head and holder.]
- After using for a period of time, you can add an appropriate amount of razor lubricant to the head (not included in the package). [Diagram: Shows lubricant being applied to the clipper head.]
Note: The electric clipper is not waterproof, please do not flush it under water to avoid damage.
Flexible hose storage
Wrap the flexible hose clockwise around the base of the vacuum device. The hose suction port can be fixed on the side of the vacuum device by magnetic connection.
[Diagram: Shows the flexible hose being wrapped around the base of the vacuum device and the suction port being magnetically attached.]
Power cord storage
The power cord can be wrapped around and stored in the slot at the bottom of the product.
[Diagram: Shows the power cord being wrapped around the base and stored in a slot.]
Common troubleshooting
| Frequently Asked Questions | Possible causes of failure | Suggested solutions |
|---|---|---|
| The product can not be powered on. | The power cord is not plugged in or there's no power to the socket. | Check if the power cord is plugged in and if the socket has power. |
| Low suction power. | The hose is blocked. | Clean the suction ports at both ends of the hose to ensure that there are no foreign objects blocking it. Avoid tangling and knotting the hose when using. |
| The dust cup is full. | Empty the dust cup. | |
| The HEPA filter or sponge filter is too filthy. | Clean the HEPA filter or the sponge filter. | |
| Dust cup or accessories are not properly installed. | Check if the dust cup or accessories are in place according to the user manual. | |
| Comb-type accessories are clogged with hair. | Promptly clean comb-type accessories by removing the hair. |
Note: If the above methods do not solve the issue, please stop using the product and contact the after-sales service for assistance.
Product main specifications
| Power supply specification | 120V~60Hz |
| Power | 600W |
| Flexible hose length | 1.5m/59inches |
| Power cord length | 1.95m/77inches |
| Dust cup capacity | 2L |
| Size of vacuum device | L320*W160*H225mm/L12.6*W6.3*H8.9inches |
| Weight | 2kg/4.4lbs |
Declaration of Conformity
Federal Communications Commission (FCC) compliance statement:
1. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- (1) This device may not cause harmful interference, and
- (2) this device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
ISEDC TO CANADIAN USERS
CAN ICES-3(B)/NMB-3(B)
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:
- (1) This device may not cause interference.
- (2) This device must accept any interference, including interference that may cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-003.
This device complies with RSS-247 of ISEDC. Operation is subject to the condition that this device does not cause harmful interference.
L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
- (1) L'appareil ne doit pas produire de brouillage;
- (2) L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Cet appareil numérique de la Classe B conforme à la norme NMB-003 du Canada.
Cet appareil est conforme à la norme RSS-247 d'ISEDC. Le fonctionnement est soumis à la condition que cet appareil ne provoque pas d'interférences nuisibles.
