Pioneer 40" Smart 3D TV

1 Unpacking

Remove all packaging from the unit. Retain the packaging. If you dispose of it, please do so according to any local regulations.

Included items:

• 1x YPbPr adapter cable
• 1x cable tidy strap
• 1x Audio in adapter cable
• 1x power cable
• 1x Scart adapter cable
• 2x AAA batteries
• 3x TV stand screws
• 1x Metal bracket
• 2x 3D glasses
• 1x TV stand
• 1x Remote control

2 Batteries in the remote control

Follow these steps to insert batteries into the remote control:

1. Slide the battery cover to open the battery compartment of the remote control.
2. Insert two AAA size batteries. Make sure the [Plus Symbol] and [Minus Symbol] ends of the batteries match the [Plus Symbol] and [Minus Symbol] ends indicated in the battery compartment.
3. Slide the battery cover back onto the remote control to close the battery compartment.

[Diagram showing remote control with numbered steps for battery insertion]

3 Attaching the TV stand

Make sure you remove all protective tape and film from the TV and stand before using your TV.

The LCD display is very fragile and must be protected at all times when installing and removing the TV stand. Be sure that no hard or sharp object, or anything that could scratch or damage the LCD display, comes into contact with it. DO NOT exert pressure on the front of the TV at any time because the screen could crack.

Steps:

1. Disconnect all cables connected to the TV.
2. Lay the TV down on a flat surface, preferably a table, with the back side facing up. Make sure the neck of the TV stand overhangs the edge of the table. Please ensure a soft cushioned material (such as a pillow or thick piece of foam) is placed beneath the screen.
3. Carefully place the glass stand onto the neck of the stand. Hold the metal bracket over the holes and fix into position using the 3 screws provided as shown.

[Diagram showing TV stand attachment process with numbered steps and screw locations]

4 Connecting the TV

Your TV has a wireless connection built in, so connecting an Ethernet cable is optional. However, this will give you the quickest internet connection.

Connections:

1. Connect the Aerial cable.
2. Connect the Ethernet cable (optional).
3. Connect the Power cable and switch on at the mains.

[Diagram showing the back of the TV with connection points labeled for Aerial, Ethernet, and Power. Also shows a 'Wireless Router' and 'Wireless Connection' graphic indicating Wi-Fi capability.]

5 Initial setup

Press the [Standby Button] to switch the TV on. Please be patient, this may take a few seconds.

To set up the internet and tune in your TV, follow the on-screen menus. For detailed instructions, please refer to your instruction book on the CD provided.

• To confirm a selection, press the [OK Button].
• To select menu items, press the [Up Arrow], [Down Arrow], [Left Arrow], [Right Arrow] buttons.

The Initial Setup will take a few minutes, please be patient.

Recommendations - Internet connection:

• Connect your TV via an Ethernet cable.

Recommendations - Tuning in TV stations:

• If you receive your TV via an aerial, choose the Antenna option.
• If you have a cable box connected by an RF cable to your TV, choose the Cable option.

If you have a digital cable box that connects via a HDMI cable, skip the tuning section. You do not need to tune in your TV; you just need to select the HDMI source to view digital cable channels.

[Screenshot of the Initial Setup menu showing language selection options like English, Български, Harvatski, Česky, Dansk]

6 Smart TV

Your TV is a Smart TV. To use Smart TV functionality, you must be connected to the internet. To enjoy Smart functionality, you will need a fast broadband connection; you may need to check your speed with your internet provider. In Smart mode, you can search the internet or browse the pre-installed apps.

For more instructions on how to use the Smart function of your TV, please refer to your instruction CD.

• Press the [SMART TV Button] on the remote control.

Please be patient; it may take a minute or two for the Smart page to load. The smart symbol will be animated while smart pages are loading.

To navigate around the Smart TV screen:

• A red box will highlight the area of the screen that is currently selected. Press the [Up Arrow], [Down Arrow], [Left Arrow], [Right Arrow] buttons to move around the screen.
• Press the [OK Button] to select an app.
• To exit Smart TV and return to normal TV, press the [TV Button], or select the TV picture on the Smart screen and press [OK Button].

To surf the internet:

• Select the 'brows 'n' app. A keyboard will appear on the screen. Press the [Up Arrow], [Down Arrow], [Left Arrow], [Right Arrow] buttons to select the letters and press [OK Button] to confirm.
• When the page loads, browse the page using the [Up Arrow], [Down Arrow], [Left Arrow], [Right Arrow] and [OK Button].
• To scroll up and down a page, press the [Page +/- Button].
• To exit a web page and return to the main Smart screen, press twice. The first press will take you back to the keyboard; the second press will take you back to the SMART screen.

[Screenshot of the Smart TV interface showing apps like 'favorites', 'QTom', 'f', 'searchin', 'ommanded Apps', 'SCARY', 'DRODISH', 'MOVIEY', 'all apps', 'FORECA', 'Search', 'conditions'. Also shows navigation instructions with arrows and OK button.]

7 3D Glasses

Unpacking the glasses:

• 3D Glasses Frame (x2)
• Right Arm (x2)
• Left Arm (x2)
• Battery (CR2025) (x2)

[Diagram showing the components of the 3D glasses: frames, arms, and batteries.]

Inserting the batteries:

1. Slide the battery compartment up.
2. Open the battery compartment.
3. Insert the supplied battery (CR2025), making sure that the [Plus Symbol] is facing down.
4. Close the battery compartment.
5. Slide the battery compartment closed.

[Diagram showing steps for inserting batteries into the 3D glasses.]

Connecting the arms:

Gently push each arm into the main body of the glasses as shown below.

[Diagram showing how to attach the arms to the 3D glasses frame.]

Pairing the 3D glasses:

You will need to pair your 3D glasses with your TV when you want to view your TV in 3D mode. The glasses will only work when your TV is in 3D mode.

1. Turn your TV on, then press the [3D Button] on your TV remote control to switch your TV into 3D mode.
2. Make sure you are within 1 meter of the TV, then press and hold the [STANDBY Button] on the 3D glasses for 6 seconds. The button will flash red. When the glasses are connected, the message 'Connection established between TV and 3D glasses' will appear. You should notice the lenses change shade.

[Diagram illustrating the pairing process: TV in 3D mode, glasses within 1 meter, pressing and holding the standby button on the glasses.]

Using the 3D glasses:

Your 3D glasses have 3 modes: Normal 3D mode, Right eye mode, and Left eye mode. Right and left eye modes are for when you are gaming in a split-screen mode.

1. Press and hold the [STANDBY Button] for 6 seconds to switch the 3D glasses on.
2. To switch the glasses back into standby, press and hold the [STANDBY Button] for 6 seconds. Your 3D glasses will also go into standby 30 seconds after you switch 3D mode off on your TV.

Make sure the TV is in 3D mode and all other TVs close to the glasses are switched off before pairing.