EK-Quantum Convection D5 User Guide
Introduction and Safety
This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our website at www.ekwb.com for updates. Before installation of this product please read important notice, disclosure, and warranty conditions printed on the back of the box.
Before you start using this product, please follow these basic guidelines:
Carefully read the manual before beginning the installation process.
The use of quality market-proven corrosion-inhibiting coolants is always strongly recommended for any liquid cooling system.
Do not use pure distilled water as a cooling liquid! For best results, EK recommends the use of EK-CryoFuel Coolants.
Box Contents
The box contains the following items:
- D5 Pump cover (1 pc)
- Mounting Mechanism: You may not need all the screws; the mounting mechanism is universal.
- Screw M4x62 (4 pcs)
Required Tools
The following tool is required for installation:
- Allen Key 2.5 mm
D5 Cover Dimensions
The D5 Pump cover has the following dimensions:
- Width: 71 mm
- Height: 71 mm
- Depth: 56 mm
Main Parts
The main components included in the package are detailed below:
| Position | EAN | Description | Quantity |
|---|---|---|---|
| 1 | 100663 | EK Badge [EK logo] | 1 |
| 2 | 103312 | D5 Cover Screw M4x62 - Black Chrome | 4 |
| 103313 | D5 Cover Screw M4x62 - Nickel | ||
| 105360 | D5 Cover Screw M4x62 - Gold | ||
| 3 | 103314 | D5 pump Cover - Black | 1 |
| 103315 | D5 pump cover - Nickel | ||
| 103571 | D5 pump Cover - Silver | ||
| 105058 | D5 pump Cover - Gold |
Preparing the Pump
Step 1: Remove Original Pump Holder
Unscrew the four (4) marked screws and remove the original pump holder. Store the holder and screws for possible reuse without the D5 Cover.
Step 2: Uninstalling Connectors
4-Pin Molex Connector
- Flatten the pins in the Molex connector.
- Remove cables from the Molex connector.
3-Pin Fan Connector
- Push the pin on the fan connector with a screwdriver.
- Remove the cable.
Attaching the Pump Cover
Step 1: Mounting the Cover
Insert the pump cables through the D5 Pump cover and place the cover over the D5 pump. Make sure that holes are aligned. Secure the D5 Pump cover using M4 x 62 mm screws and the 2.5 mm Allen Key. Do not use excessive force while tightening the screws!
Step 2: Installing the Molex Connector
- Put the screwdriver into the pin gap in the Molex connector.
- Recover the flattened pin into its original position.
- Put cables back to the Molex connector and fan connector, paying attention to the correct order of cables.
Support and Service
In case you need assistance or wish to order spare parts or a new mounting mechanism, please contact EK Water Blocks via:
https://www.ekwb.com/customer-support/
For spare parts orders, refer to the page with "MAIN PARTS" where you can find the EAN number of each part you might need. Include the EAN number with the quantity in your request. The Mounting Mechanism EAN can be found under "BOX CONTENTS". Thermal pads are readily available in the EK shop.
Social Media
Connect with EK Water Blocks on social media:
- [Facebook] EKWaterBlocks
- [Twitter] @EKWaterBlocks
- [Instagram] ekwaterblocks
- [Other] EKWBofficial
- [Pinterest] ekwaterblocks
