After reading this manual, pass the manual on to the end user to retain for future reference. The user should keep this manual for future reference and refer to it as necessary. This manual should be made available to those who repair or relocate the units. Make sure that the manual is passed on to any future air conditioning system user.
Air Conditioning Control System Centralized Controller EW-50A/EW-50E Installation and Instructions Manual Safety notes are marked with WARNING or CAUTION, depending on the severity of possible consequences that may result when the instructions are not followed exactly as stated. Proper installation is important for your safety and proper functioning of the units. Thoroughly read the following safety precautions prior to installation. Contents 1. Safety precautions........................................................................2 1-1. General precautions........................................................................................ 2 1-2. Precautions for unit installation........................................................................ 3 1-3. Precautions for electrical wiring....................................................................... 3 1-4. Precautions for relocating or repairing the unit................................................ 4 1-5. Additional precautions..................................................................................... 4 2. Introduction...................................................................................6 2-1. Part names...................................................................................................... 6 3. Package contents..........................................................................8 4. Specifications................................................................................9 4-1. Product specifications...................................................................................... 9 4-2. External dimensions...................................................................................... 10 4-3. Product features.............................................................................................11 5. System configuration...................................................................14 5-1. System restrictions........................................................................................ 14 5-2. M-NET power feeding coefficient................................................................... 15 5-3. System configuration example...................................................................... 16 5-4. Number of connectable units......................................................................... 20 5-5. Setting M-NET address for various devices.................................................. 21 6. Installation...................................................................................23 6-1. Items not included......................................................................................... 24 6-2. Items sold separately..................................................................................... 24 6-3. M-NET transmission cable length.................................................................. 25 6-4. Installation space........................................................................................... 26 6-5. Installation procedures.................................................................................. 27 7. Wiring connections......................................................................30 7-1. Removing/reinstalling the service cover........................................................ 30 7-2. Connecting AC power cables and M-NET transmission cables.................... 32 7-3. Connecting the LAN cable............................................................................. 34 7-4. Confirming the LAN transmission delay time................................................. 34 8. Initial settings..............................................................................36 8-1. Logging in to the Web Browser for Initial Settings......................................... 36 8-2. Initial settings on the Web browser................................................................ 36 8-3. Quick IP address setting................................................................................ 37 8-4. Network settings on the Web browser........................................................... 38 9. Test run.......................................................................................39 9-1. Collective operation ON/OFF........................................................................ 39 10. External input/output...................................................................40 10-1. External signal input/output function............................................................ 40 10-2. Pulse signal input function........................................................................... 44 11. Maintenance................................................................................45 11-1. Inspection and maintenance........................................................................ 45 11-2. Back up/import settings data....................................................................... 46 11-3. Software update........................................................................................... 48 11-4. Software information.................................................................................... 51 12. Error code list..............................................................................52 12-1. M-NET errors............................................................................................... 52 12-2. Errors between AE-200 and AE-50 (EW-50)............................................... 54 Before installing the controller, please read this Installation Manual carefully to ensure proper operation. Retain this manual for future reference. 1. Safety precautions Thoroughly read the following safety precautions prior to installation. Observe these precautions carefully to ensure safety. After reading this manual, pass the manual on to the end user to retain for future reference. The user should keep this manual for future reference and refer to it as necessary. This manual should be made available to those who repair or relocate the units. Make sure that the manual is passed on to any future air conditioning system user. All electrical work must be performed by qualified personnel. : indicates a hazardous situation which, if not avoided, could result in death or serious injury. : indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. : a ddresses practices not related to personal injury, such as product and/or property damage. 1-1. General precautions Do not install the controller in areas where large amounts of oil, steam, organic solvents, or corrosive gases (such as ammonia, sulfuric compounds, or acids), or areas where acidic/alkaline solutions or special chemical sprays are used frequently. These substances may significantly reduce the performance and corrode the internal parts, resulting in electric shock, malfunction, smoke, or fire. To reduce the risk of injury, electric shock, or fire, do not alter or modify the controller. To reduce the risk of electric shock, malfunction, smoke, or fire, do not touch the electrical parts or USB memory with wet fingers. To reduce the risk of injury or electric shock, before spraying a chemical around the controller, stop the operation and cover the controller. To reduce the risk of burns, do not touch the electrical parts with bare hands during and immediately after operation. To reduce the risk of injury, keep children away while installing, inspecting, or repairing the controller. Test runs, inspection, and service must be performed by qualified personnel in accordance with this manual. Incorrect use may result in injury, electric shock, malfunction, or fire. If you notice any abnormality, stop the operation and turn off the controller. Continuing the operation may result in electric shock, malfunction, or fire. Properly install all required covers to keep moisture and dust out of the controller. Dust accumulation and the presence of water may result in electric shock, smoke, or fire. To reduce the risk of frostbite, burns, injury, or electric shock, keep the equipment out of the reach of children. WT07417X01 2 To reduce the risk of fire or explosion, do not place flammable materials or use flammable sprays around the controller. To reduce the risk of electric shock or malfunction, do not touch the switches or buttons with a sharp object. To reduce the risk of injury, electric shock, or malfunction, avoid contact with the sharp edges of certain parts. To reduce the risk of injury, wear protective gear when working on the controller. Wear protective gear when working on the controller. High-voltage parts pose a risk of electric shock, and high-temperature parts pose a risk of burns. 1-2. Precautions for unit installation Do not install the controller where there is a risk of flammable gas leaks. If flammable gas accumulates around the controller, it may ignite and cause a fire or explosion. Properly dispose of the packing materials. Plastic bags pose a suffocation hazard to children. Take appropriate safety measures against earthquakes to prevent the controller from causing injury. To prevent injury, install the controller on a flat surface strong enough to support its weight. To reduce the risk of short circuits, current leakage, electric shock, malfunction, smoke, or fire, do not install the controller in a place exposed to water or in a condensing environment. The controller must be installed by qualified personnel according to the instructions detailed in this manual. Improper installation may result in electric shock or fire. 1-3. Precautions for electrical wiring To reduce the risk of malfunction, smoke, fire, or damage to the controller, do not connect the power cable to the signal terminal block. To reduce the risk of malfunction, smoke, fire, or damage to the controller, do not apply a power supply voltage in excess of that specified. Properly secure the cables in place and provide adequate slack in the cables so as not to stress the terminals. Improperly connected cables may break, overheat, and cause smoke or fire. To reduce the risk of injury or electric shock, switch off the main power before performing electrical work. WT07417X01 3 Electrical work must be performed by qualified personnel in accordance with local regulations and the instructions provided in this manual. Only use specified cables and dedicated circuits. Inadequate power source capacity or improper electrical work will result in electric shock, malfunction, or fire. To reduce the risk of electric shock, install an overcurrent breaker and an earth leakage breaker on the power supply. To reduce the risk of electric shock, smoke, or fire, install an overcurrent breaker for each controller. Only use properly rated breakers (earth leakage breaker, local switch <switch + fuse that meets local electrical codes>, moulded case circuit breaker, or overcurrent breaker). The use of improperly rated breakers or the substitution of fuses with steel or copper wire may result in electric shock, malfunction, smoke, or fire. To reduce the risk of current leakage, overheating, smoke, or fire, use properly rated cables with adequate current carrying capacity. Proper grounding must be provided by qualified personnel. Do not connect the protective ground wire to a gas pipe, water pipe, lightning rod, or telephone wire. Improper grounding may result in electric shock, smoke, fire, or malfunction due to electrical noise interference. To reduce the risk of short circuits, electric shock, or malfunction, keep wire pieces and sheath shavings out of the terminal block. To reduce the risk of short circuits, current leakage, electric shock, or malfunction, keep the cables out of contact with controller edges. To reduce the risk of electric shock, malfunction, or fire, seal the gap between the cable and the end of the conduit tube with putty. To reduce the risk of injury, do not touch the burrs of the knockout holes. 1-4. Precautions for relocating or repairing the unit The controller must be repaired or moved only by qualified personnel. Do not disassemble or modify the controller. Improper installation or repair may result in injury, electric shock, or fire. To reduce the risk of short circuits, electric shock, malfunction, or fire, do not touch the circuit board with tools or with your hands, and do not allow dust to accumulate on the circuit board. 1-5. Additional precautions To avoid damage to the controller, use appropriate tools to install, inspect, or repair the controller. To prevent unauthorized access, always use a security device such as a VPN router when connecting to the Internet. WT07417X01 4 Take appropriate measures against electrical noise interference when installing the controller in hospitals or radio communication facilities. Inverter, high-frequency medical, or wireless communication equipment as well as power generators may cause the air conditioning system to malfunction. The air conditioning system may also adversely affect the operation of these types of equipment by creating electrical noise. To avoid malfunction, do not bundle power cables and signal cables together or place them in the same metallic conduit. To avoid damage to the controller, do not overtighten the screws. To avoid deformation and malfunction, do not install the controller in direct sunlight or where the ambient temperature may exceed 55°C (131°F) or drop below -10°C (14°F). This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. WT07417X01 5 2. Introduction EW-50A/EW-50E is a total management system. Any connected air conditioning systems can be operated or monitored on the Web browser. EW-50A/EW-50E can also be used as an expansion controller of AE-200A/AE-200E. By connecting AE-200A/AE-200E, up to 200 indoor units and other equipment can be controlled. Hereafter, AE-200A and AE-200E, unless otherwise specified, will be called "AE-200." Hereafter, AE-50A and AE-50E, unless otherwise specified, will be called "AE-50." Hereafter, EW-50A and EW-50E, unless otherwise specified, will be called "EW-50." Note: A PC is required to monitor and operate the air conditioning units. Note: T he required licenses vary, depending on the functions to be used. Consult your dealer. Note: F or how to use the Web browser, refer to the Web browser instruction books (separate volume). 2-1. Part names Push switch ON/OFF Push switch Reset USB port (unused) ON/OFF Power Status LINK/ACT2 LINK/ACT1 Power Item Lit in green Unlit Lit in green ON/OFF LED Status LINK/ACT1 LINK/ACT2 Blink in green Unlit Blink in orange Blink in blue Blink in pink Blink in orange Push switch ON/OFF Reset USB port *1 The operation status of the other equipment are excluded. Service cover Description Power ON Power OFF One or more air conditioning units are ON. *1 One or more air conditioning units or other related equipment are in error. All air conditioning units are OFF. *1 Startup error Software update in progress Software update failed Data transmission in progress (LAN1) Unused Used to turn the connected air conditioning units and the other related equipment ON and OFF all at once. Used to reboot the EW-50. (This will not affect the operation status of the air conditioning units.) Unused WT07417X01 6 **Back side with the service cover removed SW1 LAN1 LAN2 (Unused) CN7 CN6 (Unused) CN4 (Unused) CN5 CN21 TB3 TB1 Ground Item Description SW1 IP addresses can be easily set with SW1. Refer to section 8-3 "Quick IP address setting" for details. LAN1 Connects to other units of equipment over the LAN via a HUB. LAN2 Unused CN7 (Pulse Input) *1 Connects to metering devices using the supplied connector. CN6 Unused CN4 Unused CN5 (External I/O) *1 Connects to an external input/output adapter PAC-YG10HA-E. (When connecting an external input/output adapter PAC-YG10HA-E, cut out the knockout hole.) CN21 (M-NET power jumper) Connects to the M-NET power jumper to supply power (default). **If another system controller is connected to the same M-NET system and the power consumption coefficient is 1.5 or above, disconnect the M-NET power jumper to supply power from the separately-sold power supply unit. (Refer to section 5-2 "M-NET power feeding coefficient" for details.) TB3 (M-NET A, B, S) (M3.5) M-NET transmission terminal block Connects to M-NET transmission cables from the outdoor unit. (A, B: Non-polarized, S: Shield) TB1 (Power source AC L/L1, N/L2) (M3.5) Connects to the power cable. Ground (M4) Connects to the protective ground wire. *1 Refer to chapter 10 "External input/output" for details. WT07417X01 7 3. Package contents The following items are included in the package. Package contents Qty. (1) EW-50 1 (2) Connector (CN6) (Unused) 1 (3) Connector (CN7) (Used for pulse input) 1 (4) L-fitting 2 (5) DIN rail attachment (for attaching DIN rail of 35 mm (1-7/16 in) width) 2 (6) DIN rail auxiliary bracket 1 (7) Roundhead screw (M3 × 12) *1 (for fixing DIN rail attachment) 4 (8) Roundhead screw (M3 × 6) *1 (for fixing DIN rail auxiliary bracket or L-fitting) 4 (9) Cable tie 4 (Two are spare.) (10) Installation and Instructions Manual (this manual) *2 1 CD-ROM *2 Installation and Instructions Manual (this manual) Instruction Book (Web Browser for Initial Settings) Instruction Book (Web Browser for System Maintenance Engineer) Instruction Book (Web Browser for User) (11) Note 1 The CD-ROM can only be played on a CD-drive or a DVD-drive. Do not attempt to play the CD-ROM on an audio CD player as this may damage your ears and/or speakers. Each document is in PDF format. Viewing documents requires a computer with Adobe® Reader® or Adobe® Acrobat® installed. "Adobe® Reader®" and "Adobe® Acrobat®" are registered trademarks of Adobe Systems Incorporated. *1 ISO metric screw thread *2 For details about the apportioned electricity billing function, refer to the Instruction Book that comes with the "Charge" license. Notes on the SD card installed on the EW-50 Do not use the SD card installed on the EW-50 for any other equipment. WT07417X01 8 4. Specifications 4-1. Product specifications Item Power supply M-NET power feeding coefficient Ambient conditions Temperature Humidity Operating temperature range Storage temperature range Dimensions (W × H × D) Weight Installation conditions Specifications 100240 VAC ± 10%; 50/60 Hz Single-phase 1.5 -10°C +55°C (+14°F +131°F) -20°C +60°C (-4°F +140°F) 30%90% RH (Non-condensing) 172 × 209 × 92 mm (6-13/16 × 8-4/16 × 3-10/16 in) **253 × 172 × 92 mm (10 × 6-13/16 × 3-10/16 in) when using L-fittings 1.7 kg (4 lbs) Only in a metal control box indoors WT07417X01 9 4-2. External dimensions (1) When using L-fittings L-fitting (supplied) L-fitting (supplied) 100 (3-15/16) 169 (6-11/16) 172 (6-13/16) (2) When using DIN rail 150 (5-15/16) 46 (1-13/16) 209 (8-4/16) 240 (9-8/16) 252 (9-15/16) Unit: mm (in) 38 (1-8/16) 92 (3-10/16) 23 (15/16) DIN rail DIN rail attachment (supplied) DIN rail auxiliary bracket (supplied) WT07417X01 10 4-3. Product features The table below summarizes the available functions and settings on the Web browser. Refer to the Web browser instruction books (separate volume) for details. User's operation functions Function Description ON/OFF The ON/OFF operation can be performed collectively or for each group or block. Operation mode The operation mode can be switched collectively or for each group or block. (The available operation modes depend on the unit model.) Set temperature The set temperature can be set collectively or for each group or block. (The available set temperatures depend on the unit model.) Air direction The air direction can be changed collectively or for each group or block. (The available air directions depend on the unit model.) Fan speed The fan speed can be changed collectively or for each group or block. (The number of available fan speeds depend on the unit model.) Auto mode is available only on the models that support Auto mode. Fan speed (LOSSNAY unit) The fan speed (3 speeds and Auto) can be changed. Fan mode (HWHP unit) The fan can be set to keep rotating even while the unit is stopped to avoid snow accumulation on the fan guard during the winter. Ventilation mode (LOSSNAY unit) The ventilation mode can be switched. Operation*1 Interlocked ventilator (LOSSNAY unit) ON/OFF Interlocked LOSSNAY units (if any) can be operated or stopped collectively or for each group or block. Prohibition of local remote controller operation Some operations or settings from the local remote controllers can be prohibited collectively or for each group or block. Filter sign reset Filter sign can be reset collectively or for each group or block. Schedule Weekly, annual, and today's schedules can be set collectively or for each group or block. Schedule (Available/ Not Avail.) The scheduled operations can be enabled or disabled. Malfunction reset Displayed errors can be reset. Clear malfunction log Displayed unit errors and communication errors can be cleared. External input Using external contact signals, the following collective operations can be controlled: Demand level, Emergency stop, ON/OFF operation, and Prohibit/Permit local remote controller operation. **A separately-sold external input/output adapter (PAC-YG10HA-E) is required. **Connect the external input/output adapter to each AE-200/AE-50/EW-50. Energy Use Status Displays and compares the energy-control-related status, such as electric energy consumption, operation time, and outdoor temperature, in a graph. Ranking Displays the rankings in electric energy consumption and the fan operation time of given indoor units in a bar graph. Monitor*1 Target Value Setting Peakcut Control Status Sets the target electric energy consumption values for the entire system for the current year, each month, each day of the week, and each block. The set values will be displayed in the graph on the [Energy Use Status] screen and the [Ranking] screen. Displays the average electric power consumption and the control level. Condition List Displays the operation status of each group. Prohibition of local remote controller operation Displays the icon to indicate that the operation is prohibited by the EW-50. Measurement List Displays the readings of the temperature sensor, humidity sensor, and metering device. WT07417X01 11 User's operation functions Initial settings Function Malfunction List Filter sign AHC List Free Contact List Malfunction Log Monitor*1 Send Mail Log Outdoor unit status External output Date and time License Operation*1 Basic System Groups Interlocked LOSSNAY Blocks E-Mail Peak Cut Functions 1*1 Measurement Energy Management Settings Set Temperature Range Limit Night Mode Functions 2*1 Schedule System-changeover External Temperature Interlock Night Setback Functions 3*1 Control Interlock control AHC Port Name Settings Description Displays the address of the unit in error and error code. Indicates that the filter on the unit in a given group is due for cleaning. Displays the input and output status of Advanced HVAC CONTROLLERs. Displays the ON/OFF status of the indoor unit free contact. Displays unit errors and communication errors. Displays a list of error notification e-mail that have been sent. Displays outdoor unit capacity value, high pressure, and low pressure of each outdoor unit. Outputs signals (ON/OFF, Error) to an external device. **A separately-sold external input/output adapter (PAC-YG10HA-E) is required. **The operation status of general equipment (via a DIDO controller (PAC-YG66DCA)) will not be output. Sets the current date/time and daylight savings time. Registers license for optional functions. Sets unit name, unit ID, IP address, subnet mask, gateway, display format, M-NET address, range of prohibited controllers, external input setting, and advanced setting. Registers air conditioning units, Air To Water (PWFY) units, LOSSNAY units, general equipments, remote controllers, and sub system controllers to a group. Interlocks the operation of indoor units and LOSSNAY units. Registers groups to a block. The e-mail server information, EW-50 e-mail information, and e-mail settings for the error notification e-mail function and e-mail communication function can be set. The Peak Cut method and control settings for outdoor and indoor units can be set. AI and PI controllers, temperature sensor, humidity sensor, and metering device can be registered. The trend data format, error notification e-mail function settings, and e-mail alarm function settings can be set. The settings related to energy-use-status display can be made. The settable temperature range can be set. The start/end times for the Night mode (quiet operation) for outdoor units can be set. This function switches the operation modes of the indoor units connected to the same outdoor unit between cooling and heating based on the room temperature and the set temperature. The target outdoor units and details for this function can be set. This function adjusts the set temperature based on the temperature difference between the set temperature and the outdoor temperature. A maximum temperature value to be added to the set temperature can be set for each group. This function performs cooling or heating operation when the room temperature goes outside of the specified temperature range. The start/end times and temperature range can be set for each group. Interlock control between the connected devices can be performed by making various settings. Up to 150 interlocking conditions can be set. The names of the AHC analog/digital input/output ports can be set. Maintenance user User settings Building manager User name and password for maintenance users can be set. User name, password, and available functions to building managers can be set. Function settings User settings WT07417X01 12 Function Description Back up settings data Backed-up settings data can be restored from the PC. Import settings data Backed-up settings data can be restored from a PC. Group setting information/ The group setting information and interlocked LOSSNAY information are retained in Interlocked LOSSNAY information the hardware, even if power is turned off. Malfunction log The malfunction log is retained in the hardware, even if power is turned off. Miscellaneous Scheduled operations The scheduled operations set for each group are retained in the hardware, even if power is turned off. Current date and time The current date and time are retained by the built-in capacitor when power is turned off. CSV output The operation data, such as apportioning parameters and power consumption, can be output. Software Update The software can be updated by inserting a CD or USB memory device in which the update file is stored to a PC. Time synchronization Clocks on the controllers and the units that are under the control of the main system controller are synchronized once a day (applicable only to the ones that support this function). *1 The item and range that can be operated or monitored depend on the unit model. WT07417X01 13 5. System configuration 5-1. System restrictions The software version of the AE-200, AE-50, and EW-50 units in a system must be the same. For details about how to update the software, refer to section 11-3 "Software update". The restrictions vary, depending on the number of the controlled units, model of the connected units, and the functions in use. 5-1-1. When not using an apportioned electricity billing function Note: A E-200 is required when using AE-50. (1) Controlling 50 or fewer units of equipment 1. AE-200 2. EW-50 AE-200 M-NET City Multi system Indoor unit EW-50 M-NET City Multi system Indoor unit Outdoor unit Remote controller Outdoor unit Remote controller (2) Controlling more than 50 units of equipment (with connection to an AE-200 controller) AE-200 HUB M-NET AE-50 M-NET Outdoor unit City Multi system Indoor unit Remote controller EW-50 M-NET M-NET 5-1-2. When using an apportioned electricity billing function Note: A E-200 is required to use a billing function. Note: A E-200 M-NET cannot be used when a billing function is used. Note: "Charge" license is required to use a billing function. M-NET AE-200 HUB AE-50 M-NET M-NET Outdoor unit EW-50 M-NET City Multi system Indoor unit Remote controller M-NET WT07417X01 14 5-2. M-NET power feeding coefficient The EW-50's power feeding coefficient is 1.5. A power supply unit is not required when the power consumption coefficient of the M-NET equipment (e.g. system controller, PI controller) that will be connected to the centralized control transmission cables is 1.5 or below. Power feeding coefficient Product EW-50 Power supply unit (PAC-SC51KUA) Power feeding coefficient 1.5 5 Power consumption coefficient Product DIDO controller (PAC-YG66DCA) PI controller (PAC-YG60MCA) AI controller (PAC-YG63MCA) System controller (North America: TC-24B, Europe: AT-50B) ON/OFF remote controller (PAC-YT40ANRA) Power consumption coefficient 1/4 1/4 1/4 1.5 1 Use a power supply unit and connect the M-NET power jumper as shown in the table below, depending on the system configuration and the power consumption coefficient of the M-NET equipment that will be connected to the centralized control transmission cables. Power supply unit M-NET power jumper (CN21) System with connection to a sub system controller or other related equipment Power consumption coefficient 1.5 Power consumption coefficient > 1.5 Not required Required Connect (Connected at factory shipment) Disconnect **Leave the M-NET power jumper connected to CN41 on all outdoor units. **Provide a single point ground for the shield of the centralized control transmission cable. (Provide the appropriate grounding according to local standards.) Refer to section 7-2-2 "M-NET transmission cables (Centralized control transmission cables)" for details. **Set the centralized control switch (SW5-1 (or SW2-1, depending on the unit model)) on the outdoor unit connected to the M-NET transmission cable to ON. **Refer to section 2-1 "Part names" for the location of CN21. WT07417X01 15 5-3. System configuration example Note The figures in (1) through (3) below only show the transmission cable connections. Power cables are omitted. (1) When the power consumption coefficient of the M-NET equipment that will be connected to the centralized control transmission cables is 1.5 or below EW-50 *1 LAN [000] M-NET Outdoor unit (Y) *2 [051] TB7 TB3 Indoor unit MA Local remote controller (MA R/C type) ME Local remote controller (ME R/C type) Sub system controller AHC Advanced HVAC CONTROLLER Group 1 Group 2 M-NET transmission cable MA remote controller cable LAN cable Numbers in parentheses indicate address numbers. [001] [002] [003] [004] [005] MA MA M-NET Outdoor unit (R2) *2 [056] TB7 TB3 BC controller [057] [006] [007] [201] ME [106] Group 3 LOSSNAY [008] [009] AHC [201] [010] Mr. Slim *3 outdoor unit Mr. Slim *3 outdoor unit [11] M-NET adapter [12] MA Group 4 MA Group 5 *1 Leave the M-NET power jumper connected to CN21 on the EW-50. *2 Leave the M-NET power jumper connected to CN41 on all outdoor units. *3 An M-NET adapter (sold separately) is required to connect the Mr. Slim model of units to the M-NET. WT07417X01 16 (2) When the power consumption coefficient of the M-NET equipment that will be connected to the centralized control transmission cables is greater than 1.5 Example: W hen two system controllers (North America: TC-24B, Europe: AT-50B) (power consumption coefficient: 1.5 each) are connected, the power consumption coefficient is 3. In this case, use a power supply unit. Power supply unit PAC-SC51KUA (sold separately) EW-50 *1 [000] LAN M-NET Outdoor unit (Y) *2 [051] TB7 TB3 M-NET Group 1 MA ME AHC Indoor unit Local remote controller (MA R/C type) Local remote controller (ME R/C type) Sub system controller Advanced HVAC CONTROLLER Group 2 M-NET transmission cable MA remote controller cable LAN cable Numbers in parentheses indicate address numbers. [001] [002] [003] [004] [005] M-NET MA Outdoor unit (R2) *2 [056] TB7 TB3 BC controller [057] MA [006] [007] ME [106] Group 3 [008] [009] AHC [201] LOSSNAY [010] [201] [202] Mr. Slim *3 outdoor unit Mr. Slim *3 outdoor unit [11] [12] M-NET adapter MA Group 4 MA Group 5 *1 Disconnect the M-NET power jumper (CN21) from the EW-50. *2 Leave the M-NET power jumper connected to CN41 on all outdoor units. *3 An M-NET adapter (sold separately) is required to connect the Mr. Slim model of units to the M-NET. WT07417X01 17 (3) When connecting AE-50/EW-50 controllers (up to four controllers) to an AE-200 1. When not using an apportioned electricity billing function Indoor unit AE-200 *1 LAN1 IP: 192.168.1.001 [000] Outdoor unit (Y) M-NET [051] *2 TB7 TB3 Group 1 ME Local remote controller (ME R/C type) AHC Advanced HVAC CONTROLLER M-NET transmission cable LAN cable Group 2 Numbers in parentheses indicate address numbers. [001] [002] [003] [004] [005] ME [101] ME [103] LAN Switching HUB LAN Outdoor unit (R2) [056] *2 TB7 TB3 BC controller [057] [006] [007] ME [106] Group 3 LOSSNAY [008] [009] AHC [201] [010] AE-50 *1 LAN1 IP: 192.168.1.211 [000] LAN EW-50 *1 LAN1 IP: 192.168.1.212 [000] LAN EW-50 *1 LAN1 IP: 192.168.1.213 [000] Outdoor unit M-NET [051] *2 TB7 TB3 Group 1 [001] [002] ME [101] Outdoor unit [051] *2 M-NET TB7 TB3 Group 1 [001] [002] ME [101] Outdoor unit [051] *2 M-NET TB7 TB3 Group 1 [001] [002] ME [101] *1 Leave the M-NET power jumper connected to CN21 on the AE-200 and EW-50. *2 Leave the M-NET power jumper connected to CN41 on all outdoor units. Group 2 [003] [004] ME [103] LOSSNAY [005] Group 2 [003] [004] ME [103] LOSSNAY [005] Group 2 [003] [004] ME [103] LOSSNAY [005] WT07417X01 18 2. When using an apportioned electricity billing function*1*2*3 AE-200 *4 LAN1 IP: 192.168.1.001 [000] Outdoor unit [051] TB7 TB3 M-NET [001] [002] ME [101] [003] [004] ME [103] *5 LAN Watt-hour meter EW-50 LAN1 IP: 192.168.1.211 [000] Switching *6 HUB LAN Outdoor unit *7 [051] TB7 TB3 M-NET Group 1 [001] [002] ME [101] LAN EW-50 LAN1 IP: 192.168.1.212 [000] *6 PI controller [005] Outdoor unit *7 [051] TB7 TB3 M-NET Group 1 [001] [002] ME [101] LAN EW-50 LAN1 IP: 192.168.1.213 [000] *6 PI controller [005] Outdoor unit *7 [051] TB7 TB3 M-NET Group 1 [001] [002] ME [101] PI controller [005] EW-50 LAN1 IP: 192.168.1.214 Outdoor unit [000] *6 *7 [051] Group 1 TB7 TB3 LAN M-NET [001] [002] Watt-hour meter ME [101] Indoor unit ME Local remote controller (ME R/C type) AHC Advanced HVAC CONTROLLER M-NET transmission cable LAN cable Pulse signal Numbers in parentheses indicate address numbers. Group 2 [003] [004] ME [103] AHC [201] Watt-hour meter *8 Group 2 [003] [004] ME [103] Watt-hour meter *8 Group 2 [003] [004] ME [103] Watt-hour meter *8 Group 2 [003] [004] ME [103] *1 "Charge" license is required to use a billing function. *2 AE-200 is required to use a billing function. *3 Even when a billing function is not used, this system configuration can be used to extend the distance (the length of centralized control transmission cables) between the AE-200 and the air conditioning units. *4 No air conditioning units can be connected to the AE-200 M-NET system when a billing function is used. *5 A built-in PI controller on the AE-200 cannot be used for a billing function. *6 A power supply unit may be required, depending on the system configuration. *7 Leave the M-NET power jumper connected to CN41 on all outdoor units. *8 Using a PI controller (PAC-YG60MCA) is recommended instead of a built-in PI controller on the AE-50/EW-50 when using a billing function. (Discrepancies may occur between the built-in PI controller reading and the actual electric energy because the pulse input cannot be obtained during the AE-50/EW-50 power failure, shutoff process, and software update.) WT07417X01 19 5-4. Number of connectable units The table below summarizes the number of connectable units in an AE-200/AE-50/EW-50 M-NET system. Unit type Number of connectable units Indoor units, independent OA processing units, LOSSNAY units, DIDO controllers (PAC-YG66DCA), Air To Water (PWFY) units, Advanced HVAC CONTROLLERs, HWHP (CAHV, CRHV) units, AI controllers (PAC-YG63MCA), PI controllers (PAC-YG60MCA) Up to 50 units (including the interlocked LOSSNAY units)*1*2*3 Indoor units, independent OA processing units, LOSSNAY units, DIDO controllers (PAC-YG66DCA), Air To Water (PWFY) units, HWHP (CAHV, CRHV) units in a group 116 units (Indoor units, independent OA processing units, LOSSNAY units, DIDO controllers (PAC-YG66DCA), Air To Water (PWFY) units, and HWHP (CAHV, CRHV) units cannot be combined in one group.) Remote controllers in a group 02 units System controllers in a group (EW-50 excluded) 04 units (Up to four remote and system controllers combined can be assigned to each group.) Advanced HVAC CONTROLLER in a group 01 unit LOSSNAY unit that can be interlocked with each indoor unit 1 unit Indoor units that can be interlocked with each LOSSNAY unit 116 units *1 The maximum number of controllable units varies, depending on the number of channels used for the DIDO controller. In a system with connection to Advanced HVAC CONTROLLERs, the number of connectable units is 60 units when using the monitoring function on the Maintenance Tool, and 70 units when not using the monitoring function on the Maintenance Tool. *2 Each contact of DIDO controller (PAC-YG66DCA) counts as one unit. *3 Although the maximum settable total number of built-in PI controllers and PI controllers (PAC-YG60MCA) for each AE-200/AE-50/EW-50 is 15, the number of them in a system with connection to one or more AE-50/EW-50 controllers must be 20 or less. (Each built-in PI controller counts as one unit.) WT07417X01 20 5-5. Setting M-NET address for various devices Designate the address for each M-NET device. The addresses cannot be overlapped within the same M-NET system. Indoor unit Outdoor unit Auxiliary outdoor unit (BC controller etc.) OA processing unit/ LOSSNAY unit Air To Water (PWFY) unit HWHP (CAHV) unit Main Box Sub Box Mr. Slim/M- and P-Series outdoor unit Room air conditioner M-NET remote controller MA remote controller Sub system controller Advanced HVAC CONTROLLER DIDO controller (PAC-YG66DCA) PI controller (PAC-YG60MCA) AI controller (PAC-YG63MCA) Address setting method Assign the lowest address to the main indoor unit in the group, and assign sequential addresses to the rest of the indoor units in the same group. Assign an address that equals the lowest indoor unit address in the same refrigerant system plus 50. Assign an address that equals the address of the outdoor unit in the same refrigerant system plus 1. Assign an arbitrary but unused address to each of these units after assigning an address to all indoor units. Assign the lowest address to the main Air To Water (PWFY) unit in the group, and assign sequential addresses to the rest of the Air To Water (PWFY) units in the same group. Assign the lowest address to the main unit in the Main Box in the group, and assign sequential addresses to the sub units in the same Main Box. Assign addresses that equal the addresses of the main and sub units in the Main Box plus 50 to the units in the Sub Box. Make the settings in the same way as with the indoor units. Requires PAC-SF81MA-E/PAC-SF82MA-E (sold separately). Make the settings in the same way as with the indoor units. Requires MAC-333IF-E/MAC-399IF-E (sold separately). Assign an address that equals the address of the main indoor unit with the lowest address in the group plus 100. Add 150 instead of 100 to set the address for a sub remote controller. Address setting is not required. Connection of two remote controllers requires the Main/Sub setting for each controller to be made. Assign an address that equals the group number of the smallest controlled group plus 200. Assign an address that equals the address of the main indoor unit with the lowest address in the group plus 200. If the address overlaps with the Sub system controller's address, assign an arbitrary but unused address between 201 and 250 to the Advanced HVAC CONTROLLER. Assign an arbitrary but unused address to the controller after completing the address setting for the units with an address between 1 and 50. The number of controllable units varies with the number of channels used. Assign an arbitrary but unused address to the controller after completing the address setting for the units with an address between 1 and 50. Assign an arbitrary but unused address to the controller after completing the address setting for the units with an address between 1 and 50. M-NET address 150 51100 52100 150 150 150 51100 150 150 101200 201250 201250 150 150 150 WT07417X01 21 [Main and Sub system controllers (M-NET)] Each group can be controlled by a Main system controller or a Sub system controller. EW-50 (AE-200/AE-50) is exclusively for use as a Main system controller and cannot be used as a Sub system controller. Main system controller Main system controller refers to a system controller that controls all other system controllers including the units they control. If a given system has only one system controller, that controller becomes a Main system controller. Group settings and interlock settings can be made only from a Main system controller. Sub system controller Sub system controller refers to a system controller that is controlled by a Main system controller. Main system controller's (EW-50 or AE-200/AE-50's) control range Sub system controller's control range Group Group Group The system cannot be configured as shown in the examples below. Groups that are not under the control of a Main system controller cannot be controlled from a Sub system controller. Main system controller Sub system controller Group Group Group Each group cannot be placed under the control of two or more Main system controllers. Main system controller 1 Main system controller 2 Group Group Group Sub system controllers cannot be placed under the control of two or more Main system controllers. Main system controller 1 Sub system controller Main system controller 2 Group Group Group Group WT07417X01 22 6. Installation Test runs, inspection, and service must be performed by qualified personnel in accordance with this manual. Incorrect use may result in injury, electric shock, malfunction, or fire. Do not install the controller where there is a risk of flammable gas leaks. If flammable gas accumulates around the controller, it may ignite and cause a fire or explosion. Take appropriate safety measures against earthquakes to prevent the controller from causing injury. To prevent injury, install the controller on a flat surface strong enough to support its weight. To reduce the risk of short circuits, current leakage, electric shock, malfunction, smoke, or fire, do not install the controller in a place exposed to water or in a condensing environment. WT07417X01 23 6-1. Items not included The following items are required to install the EW-50. Items not included Locknuts and bushing Sleeved ring terminal AC power cable/Protective ground wire Transmission cable Relay (for external input) Relay (for external output) Electrical wire for pulse input Watt-hour meter Specifications Must be suitable for the conduit tube to be used. M3.5 ring terminal (for AC power cables (L/L1, N/L2) and M-NET transmission cables (A, B, S)) M4 ring terminal (for protective ground wire) Type: S heathed cable (should not be lighter than ordinary sheathed cable IEC 60227.) (designation 60227 IEC 53)*1 Recommended type: VCT, VVF, VVR, or its equivalent Size: 0.75 to 2.00 mm² (ø1.0 to ø1.6 mm), AWG 18 to 14 Protective ground wire color: green/yellow **Use a wire with an appropriate diameter so that the wire can be fixed with the cable tie below the terminal block. A diameter of 10 mm (25/64 in) is recommended. Type: Shielded cable CPEVS ø1.2 to ø1.6 mm CVVS 1.25 to 2 mm² **CPEVS: PE*2 insulated PVC*2 jacketed shielded communication cable **CVVS: PVC*2 insulated PVC*2 jacketed shielded control cable Contact rating Rated voltage: 12 or 24 VDC Rated current: 0.1 A or above Minimum applied load: DC 1 mA Operation coil Rated voltage: 12 or 24 VDC Power consumption: Max. 0.9 W Type: Copper wire that is suitable for the terminal block of the EW-50 Size Single wire: ø0.65 to ø1.2 mm, AWG 21 to 16 Twisted wire: 0.75 to 1.25 mm², AWG 18 to 16 Must output dry voltage contact pulse for each unit pulse. Output pulse type: Semiconductor relay Pulse width: 100 to 300 ms (Resting interval: Min. 100 ms) Min. 100 ms 100 to 300 ms Output pulse unit: 0.1/1.0/10/100 kWh/pulse **An output pulse unit of 1 kWh/pulse or below is recommended. LAN cable Category 5 or above straight cable (Max. 100 m (328 ft)) Switching HUB A communication speed of 100 Mbps or faster is recommended. Overcurrent breaker (fuse or circuit breaker) Fuse Circuit breaker Rated current: 3 A **When using a fuse, use it in combination with a switch (rated current: 3 A). Type: Bipolar (2P2E) Contact distance: Min. 3 mm (1/8 in) Rated current: 3 A Earth leakage breaker Type: Bipolar (2P2E) Contact distance: Min. 3 mm (1/8 in) Rated current: 3 A Rated current sensitivity: 30 mA Operation time: Max. 0.1 sec PC Refer to the Web browser instruction books (separate volume) for PC requirements. *1 For the U.S. and Canada: designation NEC (NEPA70) or CEC *2 PE: Polyethylene, PVC: Polyvinyl chloride 6-2. Items sold separately Items sold separately External input/output adapter Model name PAC-YG10HA-E Remarks Required when using the external input/output function WT07417X01 24 6-3. M-NET transmission cable length Observe the maximum total length of M-NET transmission cables to ensure proper signal transmission to and from the connected equipment over the M-NET transmission cables. If the maximum total length is exceeded, the M-NET signals will be attenuated, resulting in communication error and control failure. Maximum total length of M-NET transmission cables: 500 m (1640 ft) Maximum total length of power feed: 200 m (656 ft) <Example> Centralized control transmission cables Centralized controller a EW-50 Outdoor unit Indoor-outdoor transmission cables c d b Outdoor unit Indoor unit e f Indoor unit Indoor unit Indoor unit Indoor unit 10 m (32 ft) M-NET remote controller (1) Maximum total length of M-NET transmission cables a + c + d (e) 500 m (1640 ft) a + b + f 500 m (1640 ft) d (e) + c + b + f 500 m (1640 ft) (2) Maximum total length of power feed for the indoor-outdoor transmission cables f 200 m (656 ft) c + d (e) 200 m (656 ft) (3) Maximum total length of power feed for the centralized control transmission cables a 200 m (656 ft) a + b 200 m (656 ft) Note The M-NET remote controller cable length should be 10 m (32 ft) or shorter. The length that exceeds 10 m (32 ft) needs to be included in the maximum total length of M-NET transmission cables (500 m (1640 ft)) and in the maximum total length of the power feed (200 m (656 ft)). If the M-NET remote controller cable is shorter than 10 m (32 ft), the length does not need to be included in the maximum total length. WT07417X01 25 6-4. Installation space The EW-50 must be installed inside the metal control box. Either the supplied L-fittings or DIN rail attachments can be used for the installation. Leave a space around the EW-50 as shown in the figure below. 50 (2) 50 (2) 50 (2) 50 (2) 50 (2) 50 (2) 150 (6) DIN rail Unit: mm (in) 50 (2) 50 (2) 150 (6) When using L-fittings 100 (4) DIN rail When using DIN rail 100 (4) WT07417X01 26 6-5. Installation procedures Note Connect the necessary cables and wires before installing EW-50, referring to chapters 7 and 10. Do not install the unit where the unit may continuously receive vibration. The continuous vibration may cause the connectors to disconnect. 6-5-1. Method 1: Installation using L-fittings 1. Have a metal control box ready. 2. Cut screw holes on the surface on which the EW-50 will be installed as shown in the figure below, taking into consideration the installation space. 3. Attach the supplied two L-fittings to the EW-50 with the supplied roundhead screws (M3 × 6). 4. Properly install the EW-50 with the M4 screws (not supplied) inside the metal control box as shown in the figure below. Temporarily tighten the top M4 screws. Temporarily place the M4 screws through the screw holes at the top of the L-fitting. Tighten the bottom M4 screws. Tighten the top M4 screws. 100 (4) Unit: mm (in) M4 screw (not supplied) 240 (9-8/16) Roundhead screw (M3 × 6) (supplied) L-fitting (supplied) EW-50 M4 Inside the metal control box Note The EW-50 to which the L-fittings are attached must be fixed to the metal control box with total of four M4 screws to prevent it from falling. The surface on which the EW-50 will be installed needs to be strong enough to support its weight (1.7 kg (4 lbs) each). WT07417X01 27 6-5-2. Method 2: Installation using DIN rail 1. Have a metal control box ready. 2. Attach the supplied two DIN rail attachments to the EW-50 with the supplied roundhead screws (M3 × 12). 3. Attach the supplied DIN rail auxiliary bracket to the EW-50 with the supplied roundhead screws (M3 × 6). EW-50 DIN rail attachment (supplied) Roundhead screw (M3 × 12) (supplied) DIN rail auxiliary bracket (supplied) Roundhead screw (M3 × 6) (supplied) 4. Mount the DIN rail (not supplied) to the metal control box. **Use a DIN rail of 35 mm (1-7/16 in) width. Max. 200 (7-14/16) Unit: mm (in) Note To secure the strength, the screw pitch must be 200 mm (7-7/8 in) or less when DIN rail is mounted to the metal control box. The surface on which the EW-50 will be installed needs to be strong enough to support its weight (1.7 kg (4 lbs) each). Do not install the EW-50 where it may receive vibration. To avoid the contact of the DIN rail fixing screws with the DIN rail attachment, do not tighten the fixing screws at the shaded areas in the figure below. Do not tighten the fixing screw here. WT07417X01 28 [Mounting/removing the EW-50 on/from the DIN rail] (1) Mounting 1. Hook the upper side of the attachments to the DIN rail. 2. Push the lower part of the EW-50 until it snaps into place. Note Ensure that the DIN rail attachments are fixed securely in place to the DIN rail. (2) Removing 1. Pull the lower part of the EW-50 toward you. 2. Remove the EW-50 from the DIN rail. Mounting Removing WT07417X01 29 7. Wiring connections To reduce the risk of malfunction, smoke, fire, or damage to the controller, do not connect the power cable to the signal terminal block. To reduce the risk of injury or electric shock, switch off the main power before performing electrical work. Electrical work must be performed by qualified personnel in accordance with local regulations and the instructions provided in this manual. Only use specified cables and dedicated circuits. Inadequate power source capacity or improper electrical work will result in electric shock, malfunction, or fire. To reduce the risk of electric shock, install an overcurrent breaker and an earth leakage breaker on the power supply. To reduce the risk of electric shock, smoke, or fire, install an overcurrent breaker for each controller. Proper grounding must be provided by qualified personnel. Do not connect the protective ground wire to a gas pipe, water pipe, lightning rod, or telephone wire. Improper grounding may result in electric shock, smoke, fire, or malfunction due to electrical noise interference. To avoid malfunction, do not bundle power cables and signal cables together or place them in the same metallic conduit. 7-1. Removing/reinstalling the service cover (1) Removing 1. Unscrew the two fixing screws on the service cover. 2. Remove the service cover. Service cover Openings on the EW-50 Fixing screws Hooks on the service cover WT07417X01 30 (2) Reinstalling 1. Insert the AC power cables and M-NET transmission cables into the openings, and then insert the hooks to the openings. Note: D o not pinch the cables between the EW-50 body and the service cover. 2. Screw down the service panel with the two fixing screws. 3. Check that there are no pinched cables between the EW-50 body and the service cover. Opening for AC power cables Opening for M-NET transmission cables Do not pinch the cables between the EW-50 body and the service cover. WT07417X01 31 7-2. Connecting AC power cables and M-NET transmission cables EW-50 Outdoor unit M-NET transmission cables for centralized control TB7 Overcurrent breaker Earth leakage breaker AC power cables 100240 VAC 7-2-1. AC power cables and protective ground wire 1. Attach M3.5 sleeved ring terminals to the AC power cables, and attach an M4.0 sleeved ring terminal to the protective ground wire. 2. Connect the AC power cables to the power supply terminal block, and connect the protective ground wire to the ground terminal. Note: T hread the protective ground wire through the guides to prevent the wire from moving when it is retightened to the ground terminal. 3. Fix the cables in place with the supplied cable tie. 45 mm (1-13/16 in) or less Protective ground wire AC power cable Cable tie (supplied) Sheath 100240 VAC Guide Guide Note Make the protective ground wire 25 mm (1 in) longer than the AC power cables (L/L1, N/L2). Tighten the terminal screws to a torque of 1.0 to 1.3 N·m. Properly fix the cable sheaths in place with the supplied cable ties. The distance between the sheath end and the ring terminal must be 45 mm (1-13/16 in) or less. Cable tie (supplied) Cable sheath WT07417X01 32 7-2-2. M-NET transmission cables (Centralized control transmission cables) 1. Attach M3.5 sleeved ring terminals to the M-NET transmission cables (A, B, Shield). 2. Connect the M-NET transmission cables to the M-NET terminal block. 3. Fix the cables in place with the supplied cable tie. 4. When the power is supplied from the unit other than the EW-50, disconnect the M-NET power jumper from CN21. (Refer to section 2-1 "Part names" for the location of CN21.) CN21 M-NET transmission cables A and B 45 mm (1-13/16 in) or less Cable tie (supplied) M-NET transmission cable S (Shield) Sheath To outdoor unit Note Provide a single point ground for the shield of the centralized control transmission cable. (Provide the appropriate grounding according to local standards.) When leaving the M-NET power jumper connected to CN21 on the AE-200/AE-50/EW-50, the M-NET S (shield) terminal of TB3 is connected to the ground terminal block on the unit, and the ground is supplied via the protective ground wire. When disconnecting the M-NET power jumper from CN21 on the AE-200/AE-50/EW-50, provide a ground point at a power supply unit (PAC-SC51KUA). Tighten the terminal screws to a torque of 1.0 to 1.3 N·m. Properly fix the cable sheaths in place with the supplied cable ties. The distance between the sheath end and the ring terminal must be 45 mm (1-13/16 in) or less. Cable tie (supplied) Cable sheath WT07417X01 33 7-3. Connecting the LAN cable To prevent unauthorized access, always use a security device such as a VPN router when connecting to the Internet. Connect the LAN cable to the LAN1 port on the EW-50. (The LAN2 port is unused.) The LAN cable is not supplied. Use a category 5 or above straight LAN cable. Use a switching HUB compatible with 100 BASE. The maximum distance between the switching HUB and AE-200/AE-50/EW-50 is 100 m (328 ft). The recommended number of connected devices such as gateway, router, layer 3 switch, or HUB between the AE-200/AE-50/EW-50 is four or less. (Transmission round-trip delay time must not exceed one second. If the transmission delay time is long, a communication error may be detected. Check the transmission delay time, referring to section 7-4.) LAN1 LAN2 (Unused) Note LAN must be installed before the unit installation. Route the LAN cable to the EW-50 in the same way as the M-NET transmission cables. When connecting the EW-50 to an existing LAN, consult the system administrator to decide the IP address. 7-4. Confirming the LAN transmission delay time Connect a monitoring PC to a device such as HUB that is connected to the AE-200/AE-50/EW-50. Send a command from the PC to the AE-50/EW-50, and receive the response from the AE-50/EW-50. Check the time between sending and receiving on the PC display. (1) Sample system connection AE-200 EW-50 Switching HUB Max. 100 m (328 ft) Monitoring PC Max. 100 m (328 ft) Max. 100 m (328 ft) WT07417X01 34 (2) Checking the transmission delay time Click [Start]>[Program]>[Accessories]>[Command Prompt] on the monitoring PC. Enter [ping (IP address of AE-200/AE-50/EW-50)], and press the Enter button. ([ping -w 1000 192.168.1.1] is entered on the sample screen below.) Check that the transmission delay time that appears on the screen is 1000 ms or below. (The transmission delay time is "Maximum = 1 ms" on the sample screen below, which is normal.) If [Request timed out] appears or the displayed transmission delay time exceeds 1000 ms, consult the network administrator for how to decrease the number of gateway, router, layer 3 switch, or HUB or how to change the network. Note The IP address of the monitoring PC should not overlap any of the addresses that are assigned to the AE-200/AE-50/EW-50. (Refer to the Instruction Book (Web Browser for Initial Settings) for how to set the IP address of the PC.) When connecting to an existing LAN system, which does not use a dedicated LAN, consult the network administrator to obtain the permission to connect the monitoring PC and the temporary IP address for the PC. Enter [ping -w 1000 192.168.1.1], and press the Enter button. Check the transmission delay time. The time should be 1000 ms or below. If [Request timed out] appears, check the LAN connection status and IP address. WT07417X01 35 8. Initial settings Initial settings need to be made for each EW-50 on the Web browser. Details about the initial settings and other settings and operations are covered in the Instruction Books (Web Browser for Initial Settings, Web Browser for System Maintenance Engineer). 8-1. Logging in to the Web Browser for Initial Settings (1) Enter the web page address in the address field of the Web browser as follows: http://[IP address of EW-50]/init/administrator.html Press the [Enter] key. A login screen will appear. Note: If the IP address of the EW-50 is [192.168.1.1], the web page address is [http://192.168.1.1/init/administrator. html]. Note: T he web page will be displayed in the same language as the operating system on the PC. The web page can be displayed in other languages by entering the web page address as follows: Chinese English French German Italian Japanese Portuguese Russian Spanish http://[IP address of EW-50]/init/zh/administrator.html http://[IP address of EW-50]/init/en/administrator.html http://[IP address of EW-50]/init/fr/administrator.html http://[IP address of EW-50]/init/de/administrator.html http://[IP address of EW-50]/init/it/administrator.html http://[IP address of EW-50]/init/ja/administrator.html http://[IP address of EW-50]/init/pt/administrator.html http://[IP address of EW-50]/init/ru/administrator.html http://[IP address of EW-50]/init/es/administrator.html (2) Enter the following default maintenance user name and password in the login screen. Default user name Default password initial init 8-2. Initial settings on the Web browser Note: Initial settings for a system with connection to an AE-200 controller differ from those in a system without it. Refer to the Instruction Book (Web Browser for Initial Settings) for details. Settings Date and Time Basic System [Default network settings] IP address: 192.168.1.1 Subnet mask: 255.255.255.0 Gateway: 0.0.0.0 Groups Interlocked LOSSNAY Blocks Functions User Settings Utility License registration Details Current date/time, daylight saving time Unit Settings, Network Settings (IP address*, Subnet mask, Gateway), Display format, System Configuration Settings (M-NET Settings, External Input Setting, Time Master/Sub) **When connecting the EW-50 to an existing LAN, consult the system administrator to decide the IP address. Group name, unit registration Interlocked unit registration Block name, group registration E-Mail, Peak Cut, Measurement, Set Temperature Range Limit, Night Mode Schedule, System-changeover, External Temperature Interlock, Night Setback Control, Interlock control, Energy Management Settings, AHC Port Name Settings Maintenance User, Building Manager Back up/import settings data License registration for optional functions WT07417X01 36 8-3. Quick IP address setting When connecting an EW-50 to a dedicated LAN system, IP address of the EW-50 can be easily set to an address between 192.168.1.1 and 192.168.1.15 with rotary switch SW1. When the IP address cannot be set with rotary switch SW1 (e.g., when connecting an EW-50 to an existing LAN, when the EW-50 is used as an expansion controller of AE-200), set the IP address on the Web browser for Initial Settings. Set SW1 before turning on the power. F 0 12 BCDE 3456 789A SW1 **The arrow on the rotary switch indicates the current setting of the switch. Point the arrow at the desired number. **To set the address, turn the rotary switch with a precision slotted screwdriver [2.0 mm (2/16 in) (width)] to a torque of less than 19.6 N·m. SW1 0 1 2 3 4 5 6 7 8 9 A B C D E F IP address (LAN1) Default 192.168.1.1 192.168.1.1 192.168.1.2 192.168.1.3 192.168.1.4 192.168.1.5 192.168.1.6 192.168.1.7 192.168.1.8 192.168.1.9 192.168.1.10 192.168.1.11 192.168.1.12 192.168.1.13 192.168.1.14 192.168.1.15 Subnet mask Default 255.255.255.0 255.255.255.0 Gateway Default 0.0.0.0 0.0.0.0 Note If you forget the EW-50 IP address, check the IP address that has been entered on the monitoring PC (Web browser or TG-2000A). If you forget the EW-50 IP address, you can start EW-50 by changing the SW1 setting and temporarily using a certain IP address (between 192.168.1.1 and 192.168.1.15). The IP address can be changed to an arbitrary IP address by setting the IP address on the Web Browser for Initial Settings, setting the SW1 back to "0", and rebooting the EW-50. (It is recommended to paste a label with the IP address on the EW-50, so that the IP address is available at all times.) WT07417X01 37 8-4. Network settings on the Web browser IP, subnet mask, and gateway addresses can be set on the Web browser. Rotary switch SW1 must be set to "0" (default setting) to make these settings. When connecting the EW-50 to an existing LAN, consult the system administrator to decide the IP, subnet mask, and gateway addresses. Refer to the Instruction Book (Web Browser for Initial Settings) for how to make these settings. WT07417X01 38 9. Test run 9-1. Collective operation ON/OFF Confirm that the group settings and interlock settings are complete before performing a test run. It may take approximately five minutes from power on until the local remote controllers become operable. Refer to the indoor unit Installation Manual for details about a test run. Note: P erform a test run in the presence of a customer. Test run procedure (1) Turn on the power to the EW-50 and all units. (2) Make sure that the Power LED on the EW-50 is lit. (3) Log in to the Web Browser for System Maintenance Engineer, and then open the [Monitor/Operation] screen. **Click [Update] to show the most recent operation conditions. (4) On the [Monitor/Operation] screen, click [Batch Operations], click [ON], and then click [OK]. The group of units will start an operation. (5) On the [Monitor/Operation] screen, check the unit icons to see if the units are in operation. (6) Check for the proper operation of each unit during the test run (e.g., check to see if cold (or warm) air comes out of the supply air outlet on each indoor unit). (7) After confirming that all units are operating properly, click [Batch Operations] on the [Monitor/Operation] screen, click [OFF], and then click [OK] to stop the units. WT07417X01 39 10. External input/output 10-1. External signal input/output function To reduce the risk of injury, do not touch the burrs of the knockout holes. To use external input/output, a separately-sold external input/output adapter (PAC-YG10HA-E) is required. When connecting an external input/output adapter (PAC-YG10HA-E), cut out the CN5 knockout hole. (Refer to section 2-1 "Part names" for the location of CN5.) Note Connect the external input/output adapter to each AE-200/AE-50/EW-50. (External input signal to AE-200 cannot perform the collective operations (e.g., emergency stop) for AE-50/EW-50 systems.) Use caution not to damage the circuit board with tools when cutting out the knockout hole. Set the [External Input Setting] setting for each EW-50 on the [Network] screen on the Web browser for Initial Settings. 10-1-1. External signal input function Using external contact signals (12 or 24 VDC), the following collective operations for all connected air conditioning units can be controlled: Demand level, Emergency stop, ON/OFF operation, and Prohibit/Permit local remote controller operation. External input M-NET External input External input M-NET M-NET External input M-NET (1) External signal input function setting Setting mode Description [Demand (Level signal)/Not in use] (Factory setting) Select this mode when inputting a demand level using a level signal, or when not using an external signal input function. A demand signal of four different levels will be input. [Emergency Stop (Level signal)] Using a level signal, all the air conditioning units connected to the AE-200 or AE-50/EW-50 will be stopped collectively in an emergency. During an emergency stop, the ON/OFF operation from the local remote controllers will be prohibited, and the ON/OFF operation and Prohibit/Permit settings on the AE-200 or AE-50/EW-50 will be prohibited. A demand signal of three different levels will be input. [ON/OFF (Level signal)] Using a level signal, all the air conditioning units connected to the AE-200 or AE-50/EW-50 will be run or stopped collectively. The ON/OFF operation from the local remote controllers will be prohibited, and the ON/OFF operation and Prohibit/ Permit settings on the AE-200 or AE-50/EW-50 will be prohibited. Scheduled operations will not be performed. [ON/OFF/Prohibit/Permit (Pulse signal)] Using a pulse signal, all the air conditioning units connected to the AE-200 or AE-50/EW-50 will be run or stopped collectively, or the operation from the local remote controllers will be prohibited or permitted collectively. **General equipment connected via a DIDO controller (PAC-YG66DCA) cannot be collectively run or stopped by using the external signal input function unless [Emergency Stop (Level signal)] is selected and relevant switches on the DIDO controller are set. **The external input function cannot be used on HWHP (CAHV) units. WT07417X01 40 (2) External signal input specifications CN5 No. 9 No. 8 No. 7 No. 6 No. 5 Lead wire from PAC-YG10HA-E Red Gray Blue Yellow Orange Demand (Level signal) Emergency Stop (Level signal) External power supply (+12 or +24 VDC) Demand level 4 Demand level 4 Demand level 3 Demand level 3 Demand level 2 Demand level 2 Demand level 1 Emergency stop signal, Normal operation signal ON/OFF (Level signal) ON signal, OFF signal ON/OFF/Prohibit/Permit (Pulse signal) Permit signal Prohibit signal OFF signal ON signal (3) Level signal and pulse signal (A) Level signal Contact ON Contact OFF Emergency Normal stop Normal Contact ON Contact OFF Stop Run Stop How the demand level is determined Demand level signal specification: When higher levels' contacts turn on, lower levels' contacts also stay on. CN5 Contact No.8 ON OFF No.7 ON OFF No.6 ON OFF No.5 ON OFF *1 *1 *1 *1 Level 4 Level 3 *1 Peak Cut control is performed when the demand level contact turns on. If two different demand levels' contacts turn on at the same time, the Peak Cut control will be performed with the higher level demand. Level 2 Level 1 Level 0 Demand level signal specification: Only the current levels' contacts turn on. CN5 Contact No.8 ON OFF No.7 ON OFF No.6 ON OFF No.5 ON OFF *2 *2 *2 Level 4 *2 The specification must be followed in the following order: When the level changes, the contact of the level after the change turns on.; The contact of the level before the change turns off. Level 3 Level 2 Level 1 Level 0 1. If [Emergency stop (Level signal)] is selected, the air conditioning units in normal operation will stop when the contact turns on. Even when the contact turns off, these units will remain stopped. They must be started up manually after the emergency stop is reset. 2. If [ON/OFF (Level signal)] is selected, the air conditioning units that are stopped will start operation when the contact turns on. Conversely, the units that are in operation will stop when the contact turns off. Note Even if the Peak Cut control is not performed due to unexpected problems, Mitsubishi Electric will not be responsible for exceeding the maximum power demand. WT07417X01 41 (4) Pulse signal (Example) ON/OFF (Example) Prohibit/Permit 0.51.0 second 0.51.0 second (ON) Contact ON Contact OFF (OFF) Contact ON Contact OFF Stop 0.51.0 second Run Stop (Prohibit) Contact ON Contact OFF (Permit) Contact ON Contact OFF Permit Prohibit 0.51.0 second Permit 1. If the input pulse signal is the same as the current operation status of the air conditioning units, no status change will occur. (For example, if an ON signal is input while the air conditioning units are in operation, the units will continue their operation.) 2. If the operation from the local remote controller is prohibited, ON/OFF status, operation mode, or temperature setting cannot be changed and filter sign cannot be reset from the local remote controller. 3. The pulse width (contact ON) should be between 0.5 and 1.0 second. (5) Recommended circuit (A) Level signal EW-50 CN5 9 8 7 6 5 1 Red External power supply *1 (12 or 24 VDC) Use relays X1, X2, Y1, and Y2 that meet the Gray Y2 Blue Y1 Yellow X2 Orange X1 following specifications. Y2 Demand level 4 Y1 X2 X1 Demand level 3 Demand level 2 Contact rating ON/OFF or Emergency Rated voltage: 12 or 24 VDC stop Demand level 1 Rated current: 0.1 A or above Max. 100 m (328 ft)*2 Minimum applied load: DC 1 mA (B) Pulse signal CN5 9 8 7 6 5 1 EW-50 Red External power supply *1 (12 or 24 VDC) Gray Y2 Blue Y1 Yellow X2 Orange X1 Max. 100 m (328 ft)*2 X1 X2 Y1 Y2 ON Prohibit OFF Permit *1 Select an external power supply suitable for the relays used. (12 or 24 VDC) Connect the external power supply in the correct polarity to input and output the signals. Connect (see the figure at left) to the negative side. *2 Take sufficient precautions against noise when the cable length is long. Important Be sure to use an external power supply (12 or 24 VDC) to avoid malfunctions. Connect the external power supply in the correct polarity to avoid malfunctions. Note The relays, DC power supply, and extension cables are not supplied. The total length of the lead wire and extension cable should not exceed 100 m (328 ft). (Use an extension cable of 0.3 mm2 or thicker.) Cut the excess cable near the connector, and insulate the end of the unused cable with tape. WT07417X01 42 10-1-2. External signal output function An ON signal is output when one or more units are in operation, and an Error signal is output when one or more units are in error. (Operation status (On/Error) of the units that are connected to each EW-50 will be output.) External output External output External output EW-50 EW-50 EW-50 M-NET M-NET M-NET External output (collective) *1 HUB EW-50 EW-50 EW-50 M-NET M-NET M-NET *1 Operation status of the total management system under the control of AE-200 (including units that are connected to AE-50 and EW-50) can collectively be output. (1) External signal output specifications CN5 Lead wire from PAC-YG10HA-E Signal No. 3 Brown Error signal, Normal signal No. 2 Black ON signal*, OFF signal No. 1 Green Common ground for external output (Ground for the external power supply) **The operation status of general equipment (via a DIDO controller (PAC-YG66DCA)) will not be output. **The ON signal will be output even during an error. (2) Recommended circuit Relay-driven circuit CN5 9 4 3 2 Diode *2 Z2 Brown Black 1 EW-50 Green Max. 10 m (32 ft) External power supply *1 Use relays Z1 and Z2 that meet the following specifications. Z1 Z1 L1 Z2 L2 Operation coil Rated voltage: 12 or 24 VDC Power consumption: Max. 0.9 W L1: ON indicator L2: Error indicator *1 Select an external power supply suitable for the relays used. (12 or 24 VDC) Connect the external power supply in the correct polarity to input and output the signals. Connect (shown in the figure at left) to the negative side. *2 Use a diode at both ends of the relay coils. Important Be sure to use an external power supply (12 or 24 VDC) to avoid malfunctions. Connect the external power supply in the correct polarity to avoid malfunctions. Do not connect the external power supply without relays being connected to the controller (no load). Note The relays, lamps, DC power supply, diodes, and extension cables are not supplied. The total length of the lead wire and extension cable should not exceed 10 m (32 ft). (Use an extension cable of 0.3 mm2 or thicker.) Each element will turn on during operation and when an error occurs. WT07417X01 43 10-2. Pulse signal input function Using pulse signals directly input from metering device such as watt-hour meter, billing data and energy management data will be obtained based on the cumulative number of pulse signal input. Note To input pulse signals directly from the metering device to the EW-50, use the connector connected to the EW-50. (A precision screwdriver for M1 screws is required.). Usability of a built-in PI controller for each function Function AE-200 AE-50 EW-50 Apportioned electricity billing function (option) x*1 V*2 V*2 Energy management V V V Demand function (option) V V V (V): Usable, (x): Not usable *1 A built-in PI controller on the AE-200 cannot be used for an apportioned electricity billing function. Use a built-in PI controller on the AE-50 or EW-50. *2 Using a PI controller (PAC-YG60MCA) is recommended instead of a built-in PI controller on the AE-50/EW-50 when using an apportioned electricity billing function. (Discrepancies may occur between the built-in PI controller reading and the actual electric energy because the pulse input cannot be obtained during the AE-50/EW-50 power failure, shutoff process, and software update.) (1) Pulse signal input specifications CN7 No. 7, 8 No. 5, 6 No. 3, 4 No. 1, 2 Signal Metering device 4 (count input) Metering device 3 (count input) Metering device 2 (count input) Metering device 1 (count input) (2) Recommended circuit 12 VDC CN7 (8) (7) (6) (5) (4) (3) (2) (1) P4 P3 P2 P1 A voltage of 12 VDC is applied to CN7. Do not apply a power voltage from any other power source. AE-200/AE-50/EW-50 Max. 100 m (328 ft) Contact rating Rated voltage: 12 VDC Rated current: 0.1 A or above Minimum applied load: DC 1 mA Note The total length of the lead wire and extension cable should not exceed 100 m (328 ft). (Use an extension cable of 0.3 mm2 or thicker.) Cut the excess cable near the connector, and insulate the end of the unused cable with tape. Do not run the signal input cable adjacent to the M-NET transmission and power cables. Do not let the cable form a loop. Peel off the sheath to 6 ±1 mm (4/16 ±1/16 in) from the end, and securely insert the cable into the terminal. Leave adequate slack in the cables so that the weight of them will not strain the terminal connectors. Use cable clamps or trunk terminals as necessary. WT07417X01 44 11. Maintenance 11-1. Inspection and maintenance Air conditioning units including EW-50 controllers may be damaged after long use, resulting in a performance drop or the units becoming a safety hazard. To use them safely and maximize their lives, it is recommended that a maintenance contract with a dealer or qualified personnel be signed. If the contract is signed, service technicians will periodically inspect the units to identify any damage at an early stage, and take appropriate measures. <Reference> Maintenance/replacement cycle of components Component Maintenance/replacement cycle Controller (EW-50) 10 years **"Maintenance/replacement cycle" is not a warranty period. **"Maintenance/replacement cycle" indicates the estimated cycle period in which each component should be replaced or repaired. WT07417X01 45 11-2. Back up/import settings data The settings data that have been made from the Web Browser for Initial Settings can be exported to an HDD as a backup. The exported data can be imported back to the AE-200/AE-50/EW-50 to restore the previous settings after AE-200/AE-50/EW-50 replacement. Click [Utility] in the menu bar, and then click [Back up/import settings data] to access the Back up/import settings data screen. Note: B ack up/import settings data function is accessible only if logged in as a maintenance user. Data import source The path to the file to be imported will appear. Back up settings data Click to back up the EW-50 settings data. Browse... Click to browse for a file that contains the data to be imported. Import settings data Click to import the file specified in the "Data import source" field to the EW-50. 11-2-1. Backing up settings data (1) To back up the data, click [Back up settings data]. The settings data will be created and the Window's standard file download dialog will appear. Note: It will take a few minutes to create the settings data. Note: T he name of the settings data will be "SettingData.dat". WT07417X01 46 11-2-2. Importing settings data (1) Click the [Browse...] button to launch the explorer and browse for a file that contains the data to be imported. Select the desired file, and click [Open]. The path to the file to be imported on an HDD will appear in the [Data import source] field. (2) Click [Import settings data] to import the data from an HDD to the EW-50. Note: It will take a few minutes to import the settings data. (3) When the settings data has been successfully imported, the EW-50 will restart. (4) Go back to the login screen and login again. WT07417X01 47 11-3. Software update The EW-50 software can be updated by using a Web browser. USB CD PC for update LAN HUB EW-50 11-3-1. Preparation Follow the instructions below to change the IP address of the PC that is used for software update. Note: W hen the system is connected to the existing LAN, ask the system administrator for permission before changing the IP address settings and updating the software. (1) Click [Control Panel] in the Start menu, and click [Network and Sharing Center]>[Local Area Setting]. In the [Local Area Connection Status] window, click [Properties]. (2) Click [Internet Protocol Version 4 (TCP/IPv4)] to select it, and click [Properties]. WT07417X01 48 (3) In the [Internet Protocol Version 4 (TCP/IPv4) Properties] window, check the radio button next to [Use the following IP address]. Enter [192.168.1.*] in the [IP address] field. (The number indicated with an asterisk must be different from the IP address of the EW-50 to be updated.) Leave [255.255.255.0] in the [Subnet mask] field as it is. Note: If the IP address of the EW-50 is [192.168.1.1], set the same 1st, 2nd, and 3rd numbers and different 4th number, such as [192.168.1.2]. Note: D efault IP address of EW-50 is [192.168.1.1]. Note: W hen performing an update on a PC that is already connected to the existing LAN, [255.255.255.0] may not appear in the [Subnet mask] field. When [255.255.0.0] appears, enter the same 1st and 2nd numbers (192.168) and different 3rd or 4th number of the IP address of the EW-50 in the [IP address] field. Caution: Obtain an approval from the client for the following precautions as necessary. 1. The communication between EW-50 and the air conditioning units will stop while the software is being updated. Although the unit in operation may detect a communication error and an error sign may appear on the local remote controllers, the unit will continue its operation and be operable from the local remote controllers. **Note that Mr. Slim indoor units or systems with no local remote controllers may detect a communication error and come to an abnormal stop. 2. Record the operation status of the air conditioning units immediately before updating the software. After the software update completes, check the operation status of the units, and manually operate the units as necessary. 3. Some operations and functions, such as scheduled operations, billing function, Peak Cut control, energy management function, will be disabled while the software is being updated. Check the setting details of these functions beforehand, and update the software when it does not affect these functions. 4. If the functions in the table below are used on the TG-2000A, avoid updating the software during the time period indicated in the right column. TG-2000A function in use Time period in which the update is prohibited Electricity charge apportioning function AM 4:05 4:35 Malfunction log backup AM 0:05 0:15 Peak Cut data backup AM 2:00 2:10 Measurement trend data backup AM 1:05 1:15 5. CSV output data (e.g., energy management data) will lose up to 60-minute worth of data. 6. When a built-in PI controller is used, pulse signals cannot be input while the software is being updated. WT07417X01 49 11-3-2. Update procedures (1) Make sure that the PC that has been set in section 11-3-1 above and the EW-50 to be updated are connected with a LAN cable. (2) Turn on the power to the EW-50, and insert a CD or USB memory device in which the update file is stored to the PC. (3) Enter the web page address in the address field of the Web browser as follows: https://[IP address of each EW-50]/swupdate/Update.html Press the [Enter] key. Note: If the IP address of the EW-50 is [192.168.1.1], the web page address is [https://192.168.1.1/swupdate/Update.html]. (4) If the security certificate is invalid, a security certificate error page (as shown at right) will appear. Click [Continue to this website (not recommended)]. (5) Enter the maintenance user name and the password in the login screen, and click [OK]. (Default user name: initial, Default password: init) (6) A software update screen will appear. (7) Click the [Browse...] button and select the update file (AExx_ FW####.dat) stored in the CD or USB memory device, and click [Start Update]. Note: The software cannot be downgraded to an earlier version. (8) A software update process starts. Note: It takes about ten minutes to complete the update. Note: D o not disconnect the LAN cable or turn off the power to the EW-50 while the software is being updated. WT07417X01 50 (9) The EW-50 will reboot after the update is complete. Check that the version that will appear on the screen is the same as the version of the update file. Also check that the version displayed on the Web browser (the Registration of Optional Functions screen, via the Web Browser for Initial Settings) is also the same. If the software update did not properly complete, update the software again. If the problem persists, the EW-50 may be damaged. Consult your dealer. 11-4. Software information Detailed information about the open source software of the AE-200/AE-50/EW-50 can be checked by accessing the following address: https://[IP address of each AE-200, AE-50, or EW-50]/license/ **Accessible only if logged in as a maintenance user. WT07417X01 51 12. Error code list Error codes and their definitions are shown below. If an error occurs, note the error code and consult your dealer. (A) indicates A-control units. 12-1. M-NET errors 0092 0093 0094 0095 0097 0100 01*0 01** 0403 0404 0701 0702 0703 0704 0705 0706 0707 0708 0709 0900 1000 10*0 1102 1108 11** 1300 13** 1500 1501 1502 1503 1504 1505 1506 1507 1508 1509 1510 1511 1512 1513 1559 2000 20*0 21** 23** 2500 2501 2502 2503 2504 2505 2506 2507 2600 2601 2602 2603 2604 2613 3152 3182 3600 Version combination error System configuration change warning "Charge" license not registered Warning - possibility of damaged metering device Apportioned calculation data collection error Equipment abnormality Equipment abnormality (PAC-YG66DCA) in system * Equipment abnormality in system ** Serial transmission trouble Indoor unit EEPROM error (A) Combustion circuit abnormality (A) Combustion heat exchange overheating protection (A) Accidental fire (A) Heater abnormality (A) Seismoscope malfunction (A) Flame current sensor abnormality (A) Ignition abnormality (A) Blower motor rotation abnormality (A) Oil pump circuit abnormality (A) Test run Refrigerant cycle abnormality Refrigerant cycle abnormality in line * Discharge temperature abnormality (TH4) (A) Inner thermo (49C) operation (A) Refrigerant cycle temperature abnormality - Common operand: ** Low-pressure abnormality (63L operation) (A) Refrigerant cycle pressure abnormality - Common operand: ** Refrigerant cycle not operate due to overcharge Refrigerant cycle not operate due to undercharge (/compressor shell temperature abnormality) Refrigerant cycle not operate due to liquid back /Low-discharge super heat abnormality (A) Refrigerant cycle not operate due to coil frost Refrigerant cycle not operate due to overheat protection Refrigerant cycle not operate due to compressor vacuum operation protection/refrigerant low temperature abnormality Refrigerant cycle not operate due to refrigerant pump abnormality Refrigerant cycle not operate due to composition detection abnormality Refrigerant cycle not operate due to control valve fault Refrigerant cycle not operate due to high pressure abnormality (ball valve closed) Refrigerant cycle - Gas leakage Refrigerant cycle not operate due to oil slick abnormality Refrigerant cycle not operate due to a stop of freezing protection function Refrigerant cycle - Brine freezing Oil balance circuit abnormality Water system abnormality (Pump interlock abnormality) Water system abnormality in line * Water system temperature abnormality - Common operand: ** Water system pressure abnormality - Common operand: ** Water system not operate due to water leak Water system not operate due to water supply suspension Water system not operate due to drain pump abnormality Water system not operate due to drain sensor abnormality/float switch function Water system not operate due to liquid level abnormality Water system not operate due to cool water valve abnormality Water system not operate due to warm water valve abnormality Water system not operate due to dew condensation prevention control activated Water system operation restricted due to water leak Water system operation restricted due to water supply suspension/humidifier water supply suspension Water system operation restricted due to drain pump abnormality Water system operation restricted due to drain sensor abnormality Water system operation restricted due to liquid level abnormality Drop in water flow rate Air system operation restricted due to inverter control box inner temperature abnormality Air system operation restricted due to housing inner temperature abnormality Air system operation restricted due to filter clogging WT07417X01 52 3601 3602 37** 38** 4000 40*0 4100 4101 4102 4103 4104 4105 4106 4107 4108 4109 4110 4111 4112 4113 4114 4115 4116 4117 4118 4119 4121 4123 4124 4125 4200 420* 4210 421* 4220 422* 4230 423* 4240 424* 4250 425* 4260 426* 5000 50*0 51** 5202 52** 5300 53** 54** 55** 56** 57** 58** 59** 6000 6101 6102 6200 6201 6202 6204 6500 6600 6601 6602 6603 6604 6605 Air system operation restricted due to filter maintenance Air system operation restricted due to damper position detecting abnormality Air system operation humidity abnormality allowance - Common operand: ** Air system operation humidity abnormality - Common operand: ** Electric system abnormality Electric system abnormality in line * Electric system not operate due to overcurrent shut-off Electric system not operate due to overcurrent protection Electric system not operate due to open phase /Open phase (T phase) (A) Electric system not operate due to reversed phase/open phase Electric system not operate due to electric leak Electric system not operate due to short circuit Electric system not operate due to self power supply OFF/power failure Electric system not operate due to overload Electric system not operate due to overload protection/OCR51C /Open phase (S phase),51CM connector open (A) Electric system not operate due to OCR51F Electric system not operate due to high voltage part Electric system not operate due to bus current Electric system not operate due to coil overheat 49°C Electric system not operate due to heater overheat Electric system not operate due to fan controller abnormality Electric system not operate due to power supply synchronism abnormality /Input circuit (board) failure Electric system not operate due to motor abnormality/speed abnormality Compressor self-protection function operation (A) Opposite phase detection circuit (board) failure (A) Open of 2 or more connectors (A) Electric system not operate due to trouble in equipment to which a measure against higher harmonics is taken Electric system not operate due to Inverter output error Electric system not operate due to damper abnormality Electric system - Rush-proof circuit abnormality Inverter abnormality Inverter abnormality - Inverter No.: * Inverter overcurrent shut-off Inverter overcurrent shut-off - Inverter No.: * Inverter bus voltage insufficiency / Voltage abnormality (A) Inverter bus voltage insufficiency - Inverter No.: * Inverter radiating thermostat abnormality Inverter radiating thermostat abnormality - Inverter No.: * Inverter overcurrent (overload) protection Inverter overcurrent protection - Inverter No.: * Inverter IPM/bus voltage abnormality /Power module abnormality (A) Inverter IPM abnormality * Inverter cooling fan trouble Inverter cooling fan trouble - Inverter No.: * Sensor trouble Sensor trouble in system * Temperature sensor trouble - Sensor No.: ** Connector (63L) open (A) Pressure sensor trouble - Sensor No.: ** Current sensor abnormality (A) Current sensor trouble - Sensor No.: ** Humidity sensor trouble - Sensor No.: ** Gas sensor trouble - Sensor No.: ** Air speed sensor trouble - Sensor No.: ** Limit switch trouble - Switch No.: ** Sensor trouble - Sensor No.: ** Other sensors trouble - Sensor No.: ** System abnormality System not operate due to abnormality - With response frame No answer back Controller H/W abnormality E2PROM abnormality RTC abnormality External memory read/write error Communication error Communication error - Address duplicate Communication error - Polarity unsettled Communication error - Transmission processor hardware error Communication error - Transmission line busy Communication error - No ACK (06H) (communication circuit error) Communication error - No response frame WT07417X01 53 6606 6607 6608 6609 6610 6800 6801 6810 6811 6812 6813 6820 6821 6822 6823 6824 6830 6831 6832 6833 6834 6840 6841 6844 6845 6846 7000 7100 7101 7102 7103 7104 7105 7106 7107 7108 7109 7110 7111 7112 7113 7116 7117 7130 7131 7132 7200 7201 73** Communication error - Transmission processor communication error Communication error - No ACK return Communication error - No return of response frame Communication error Communication error Communication error - Other communication errors Communication error - V-control communication error Communication error - UR communication error Communication error - UR communication synchronism not recover Communication error - UR communication hardware error Communication error - UR communication status bit detection error Other communication errors Other communication errors - Transmission line busy Other communication errors - No communication ACK Other communication errors - No response command Other communication errors - Receive data error Communication error - MA communication refrigerant address double setting error Communication error - No MA communication reception error Communication error - MA communication synchronism not recover Communication error - MA communication transmission/reception hardware trouble Communication error - MA communication start bit detection error Communication error - A control no indoor/outdoor communication/reception abnormality Communication error - A control indoor/outdoor communication synchronization recovery abnormal Communication error - A control indoor/outdoor communication incorrect indoor/outdoor wiring connection, excessive number of indoor units (more than five units) Communication error - A control indoor/outdoor communication incorrect indoor/outdoor wiring connection (telecommunication, disconnection) Communication error - A control indoor/outdoor communication startup time exceeded System abnormality System abnormality - Total capacity error System abnormality - Capacity code error System abnormality - Connecting unit number excess System abnormality - Piping length setting error System abnormality - Floor height setting error System abnormality - Address setting over 254 System abnormality - Attribute setting error System abnormality - Distributor setting error System abnormality - Refrigerant system setting error System abnormality - Connection setting error System abnormality - Refrigerant system connection/connection data unsettled System abnormality - I/O connection equipment not connected/remote controller sensor abnormality System abnormality - I/O type setting error System abnormality - Equipment unsettled System abnormality - Replace non-wash setting error System abnormality - Model identification setting error System abnormality - Different unit model error System abnormality - Mixed cooling only H/P connection error (Facility PAC) System abnormality - Multiple entries of operation performance (Facility PAC) System abnormality - Numeric values unsettled System abnormality - Numeric values unsettled System abnormality - LON system equipment abnormality 12-2. Errors between AE-200 and AE-50 (EW-50) 6920 6922 7901 7902 7903 7904 7905 No response error Response ID error Maximum connectable No. of units exceeded Connection lock error Unit information error System setting error Version error WT07417X01 54 SD and SDHC Logos are trademarks of SD-3C, LLC. Java is a registered trademark of Oracle and/or its affiliates. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. WT07417X01 55 Bu uyarinin içerii sadece Türkiye'de geçerlidir. · irketimizdeki gelitirme faaliyetlerinden dolayi ürün özelliklerinin, haber verilmeksizin deitirilme hakki tarafimizda saklidir. · Anma deerleri için TS EN 14511 / TS EN 14825 deki iklim artlari ile tarif edilen koullar esas alinmitir. · ç ve di ortam sicakliklarinin standartlarda esas alinan deerlerin diina çikmasi durumunda klimanizin isitma ve soutma kapasitelerinin etkilenmesi doaldir. · Ürünün üzerinde bulunan iaretlemelerde veya ürünle birlikte verilen dier basili dokümanlarda beyan edilen deerler, ilgili standartlara göre laboratuvar ortaminda elde edilen deerlerdir. Bu deerler, ürünün kullanim ve ortam artlarina göre deiebilir. · Satin almi olduunuz ürünün kullanim ömrü 10 yildir. Bu, ürünün fonksiyonunu yerine getirebilmesi için gerekli yedek parça bulundurma süresidir. Ürünün montaji için Mitsubishi Electric Turkey Elektrik Ürünleri A.. yetkili servisine / bayisine bavurunuz. Servis stasyonlari ve Yedek Parça Temini : Cihazinizin bakim, onarim ve yedek parça ihtiyaçlari için klimanizi satin aldiiniz yetkili saticiya bavurunuz. Yetkili Servislerimizin listesine [www.klima.mitsubishielectric.com.tr] adresinden veya 444 7 500 numarali telefondan ulaabilirsiniz. Ünitenin ihtiyaç duyacai bakim ve onarim parçalari 10 yil boyunca üretilecektir. thalatci Firma: Mitsubishi Electric Turkey Elektrik Ürünleri A.. erifali Mah. Kale Sk. No: 41 34775 Ümraniye / stanbul / Türkiye Tel: + 90 216 66 100 66 Faks: + 90 216 661 44 47 klima@tr.mee.com www.klima.mitsubishielectric.com.tr Merkez Ofis (Head Office) Büyükdere Cad. Maya Akar Center C Blok No: 4/9 34394 Esentepe-ili, stanbul, Türkiye Tel: +90 212 318 90 86 www.mitsubishielectric.ae/turkey/ Üretici Firma: Mitsubishi Electric Corporation (Head Office) Tokyo Building 2-7-3, Marunouchi, Chiyoda-ku, Tokyo 100-8310, Japan Tel: +81 (3) 3218-2111 www.mitsubishielectric.com WT07417X01 56 WT07417X01 57 WT07417X01 58 WT07417X01 59 This product is designed and intended for use in the residential, commercial and light-industrial environment. The product at hand is based on the following EU regulations: · Low Voltage Directive 2006/95/EC · Electromagnetic Compatibility Directive 2004/108/EC · Restriction of Hazardous Substances 2011/65/EU Please be sure to put the contact address/telephone number on this manual before handing it to the customer. HEAD OFFICE: TOKYO BLDG., 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN WT07417X01 872C595A30Adobe PDF Library 9.9