SilverStone
User Manual for SILVERSTONE models including: RM47-502I, RM47-502I 4U Interchangeable Rackmount Chassis, 4U Interchangeable Rackmount Chassis, Interchangeable Rackmount Chassis, Rackmount Chassis, Chassis
RM47-502I
RM47-502-I
File Info : application/pdf, 5 Pages, 44.95MB
DocumentDocumentFull-height expansion card installation
Remove both expansion card holder and the riser cable holder
Unfasten and remove the 4 screws securing the horizontal expansion card module
Remove the horizontal expansion card module
Full-height graphics card in horizontal orientation installation
Remove the PCI slots
RM47-502I
User manual www.silverstonetek.com
Accessories Content
Motherboard standoff
Motherboard screws
2.5" SSD Screws (M3-5)
2.5" SSD Screws 3.5" HDD Screws PSU mounting
(M3-4)
(#6-32)
screws
PSU mounting bracket
Handlebars
Handlebar bracket
Handlebar screws Conductive foam Cable ties
Install the graphics card onto the horizontal expansion card module
Left and right adjustment
Secure the graphics card, expansion card module, and expansion card holder back into the chassis
Different adjustment positions for the expansions card holder
First, place the graphics card into the expansion card holder, then install the graphics card, expansion card module and expansion card holder into the chassis
2
Secure the expansion card module with screws at the Adjusting the expansion card holder
front chassis, and secure the expansion card holder
with screws on both sides of the chassis
Front and back adjustment
1
The adjustable positions are as follows
Position 1 Position 2 Position 3 Position 4 Position 5 Position 6
Place the rubber dampening padding under the graphics card and double check the padding does not interfere with the graphics card cooling fans
Fixating the riser card holder
Remove the riser cable holder first before installing the riser cable
Attach the riser cable to the riser cable bracket and secure with screws (Optional SST-RC05 PCIe Gen 5 riser cable can be purchased)
Velcro straps
User manual
1
Connect the riser cable to the motherboard and graphics card then secure the whole module with screws
Riser cable holder and CPU cooler compatibility
CPU Cooler
Maximum height with riser cable holder: 114mm Maximum height without riser cable holder: 148mm
PSU mount and 5.25" drive cage interchangeability instructions
Preparation Remove the top panel
Remove both expansion card holder and the riser cable holder
114mm Maximum: 148mm
Removal of PSU mounting bracket Unfasten and remove the PSU mounting bracket screws
Remove the PSU mounting bracket from the rear chassis panel Remove the bottom PSU mounting bracket screws located at outer side of the bottom chassis
Remove the bottom PSU mounting bracket located at the bottom of the chassis
5.25" drive cage removal
Unfasten and remove the 4 screws on the side securing the drive cage
PSU mount and 5.25" drive cage interchangeability instructions
Adjust the 5.25" drive cage position to the rear, and the PSU mounting bracket to the front
Secure the corresponding screws
Installation of components in the 5.25" drive cage
Installing conductive foam to fill the gaps on the drive cage
2
Installing 2 x 5.25" ODD drives
5.25"ODD *1
Storage drive installation options
PSU Installation
ATX (PS2) Installation
5.25" ODD x 1 or 3.5" HDD x 1 or 2.5" SSD x 2
or
3.5" HDD *1 or
2.5" SSD *2
First remove the beams that supports the expansion card retainer PSU mounting bracket is pre-installed at the rear side, if the positions is to be interchanged, ensure the PSU mounting bracket is also moved to the front PSU mounting position for installation
Secure PSU with screws
Mini Redundant Installation
Remove the PSU mounting bracket
Attach and secure the additional PSU mounting bracket included Install and secure the PSU to the chassis in the accessories package to the chassis
50mm
I/O panel can also be interchanged between front and rear side
Rear mounting position / Front mounting position
Handlebars can also be interchanged between the front and rear side
Rear mounting position / Front mounting position
OR
Rail slides
Due to its interchangeable nature, when mounting the RMS05-22 rail slides, ensure that the inner rails are screwed and secured into the designated mounting holes
Rear mounting position
Rear mounting position Front mounting position
Rear mounting position OR Front mounting position
Front mounting position
3
114 mm Maximum 148mm 142mm 142mm
Component restrictions
CPU cooler height limitations Maximum height with expansion card holder: 114mm Maximum height without expansion card holder: 148mm
CPU cooler is allowed to protrude 7mm over the edge of the motherboard
Maximum7mm
When 2.5" SSD mounting bracket is installed on the side, the distance between the CPU cooler and the edge of the motherboard must be greater than 5mm
2.5"SSD or
2.5"bracket NN
PSU and 5.25" device restrictions
The measurements from the front to the rear is 455mm Considering the cable management requirements, it is recommended that the length of the PSU and 5.25" device should not exceed 430mm
455mm 254mm
5.25"Device
Power Supply
Graphics card restrictions
Graphics card and fan/radiator total thickness cannot exceed 438mm
The total thickness of the full-height graphics card + the height of the low-profile expansion card equates to 142mm
Maximum 438mm
Graphics card
Full-height graphics card on top Low-profile expansion card on the bottom
Radiator restrictions
I/O panel installed at the rear The radiator compatibility allows three combinations between 280mm, 240mm or 120mm
120mm radiator x2
When installing a 280mm radiator, please install the fan(s) between the rear chassis panel and the radiator to avoid interference with the I/O panel
240mm radiator x1
280mm radiator x1
Maximum length limitation for radiator Max. 333mm
4
Cooling fans limitations
If the I/O panel is located at the rear, the maximum number of fans is 2 x 140mm If the I/O panel is located at the front, allows installation of 160mm fans with 140mm mounting holes
140mm x 2 160mm x 2
(would interfere with I/O panel)
120mm x2 140mm x2
160mm x2
* (I/O panel can not be simultaneously installed)
Installation of RS232 ports
Can purchase optional SilverStone ECD01 (Internal USB 2.0 to dual RS232 port adapter) to be installed in the RS232 reserved ports
140mmmounting holes
Warranty Information
This product has a limited 1 year warranty in North America and Australia. For information on warranty periods in other regions, please contact your reseller or SilverStone authorized distributor. https://silverstonetek.com.cn/
Warranty terms & conditions
1. Product component defects or damages resulted from defective production is covered under warranty. Defects or damages with the following conditions will be fixed or replaced under SilverStone Technology's jurisdiction.t
a) Usage in accordance with instructions provided in this manual, with no misuse, overuse, or other inappropriate actions.
b) Damage not caused by natural disaster (thunder, fire, earthquake, flood, salt, wind, insect, animals, etc...) c) Product is not disassembled, modified, or fixed. Components not disassembled or replaced. d) Warranty mark/stickers are not removed or broken.
Loss or damages resulted from conditions other than ones listed above are not covered under warranty.
2. Under warranty, SilverStone Technology's maximum liability is limited to the current market value for the product (depreciated value, excluding shipping, handling, and other fees). SilverStone Technology is not responsible for other damages or loss associated with the use of product.
3. Under warranty, SilverStone Technology is obligated to repair or replace its defective products. Under no circumstances will SilverStone Technology be liable for damages in connection with the sale, purchase, or use including but not limited to loss of data, loss of business, loss of profits, loss of use of the product or incidental or consequential damage whether or not foreseeable and whether or not based on breach of warranty, contract or negligence, even if SilverStone Technology has been advised of the possibility of such damages.
4. Warranty covers only the original purchaser through authorized SilverStone distributors and resellers and is not transferable to a second hand purchaser.
5. You must provide sales receipt or invoice with clear indication of purchase date to determine warranty eligibility.
6. If a problem develops during the warranty period, please contact your retailer/reseller/SilverStone authorized distributors or SilverStone http://www.silverstonetek.com. Please note that: (i) You must provide proof of original purchase of the product by a dated itemized receipt; (ii) You shall bear the cost of shipping (or otherwise transporting) the product to SilverStone authorized distributors. SilverStone authorized distributors will bear the cost of shipping (or otherwise transporting) the product back to you after completing the warranty service; (iii) Before you send the product, you must be issued a Return Merchandise Authorization ("RMA") number from SilverStone. Updated warranty information will be posted on SilverStone's official website. Please visit http://www.silverstonetek.com for the latest updates.
Additional info & contacts
For North America (usasupport@silverstonetek.com) SilverStone Technology in North America may repair or replace defective product with refurbished product that is not new but has been functionally tested. Replacement product will be warranted for remainder of the warranty period or thirty days, whichever is longer. All products should be sent back to the place of purchase if it is within 30 days of purchase, after 30 days, customers need to initiate RMA procedure with SilverStone Technology in USA by first downloading the "USA RMA form for end-users" form from the below link and follow its instructions. http://silverstonetek.com/contactus.php For Australia only (support@silverstonetek.com) Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Please refer to above "Warranty terms & conditions" for further warranty details. SilverStone Technology Co., Ltd. 12F No. 168 Jiankang Rd., Zhonghe Dist., New Taipei City 235 Taiwan R.O.C. + 886-2-8228-1238 (standard international call charges apply) For Europe (support.eu@silverstonetek.de) For China (support@silverstonetek.com.cn) For all other regions (support@silverstonetek.com)
(Pb)
/
(Hg)
(Cd)
(Cr(VI))
(PBB)
(PBDE)
SJ/T 11364 GB/T 26572 ×GB/T 26572
G11251200
5