Unni Digital Wireless Weather Station

Package Included

• UN0581 weather station x 1
• UN02 wireless sensor x 1
• Operating instructions

Technical Data

Base Unit (Model: UN0581)

Power supply: 3 x LR03 (AAA) / 1.5 V

Temperature measuring range: 14.2°F ~ 122°F (-9.9°C ~ 50°C)

Resolution: 0.1°F (0.1°C)

Temperature measuring accuracy: +/-0.5°F

Humidity measuring range: 1% to 99% relative humidity

Humidity measuring accuracy: +/- 2% (20%-80% RH), +/-4% (1%-19% and 81%-99% RH)

Resolution: 1%

Temperature and humidity data detection/sending period: every 30 seconds

Barometric and weather data detection/sending period: every 1 hour

Wireless Sensor (Model: UN02)

Batteries: 2 x LR6 (AA) 1.5 V

Temperature measuring range: -40°F to 158°F (-50°C to 70°C)

Protection type: IPX4 (splash water resistant)

Transmission frequency: 433 MHz

Range: max. 328 ft (100 meters) in open area

Temperature and humidity data detection/sending period: every 30 seconds

Note: Design and technology may change due to continuous product development.

Product Functions

Weather Station

• Indoor temperature display in °C/°F
• Indoor and outdoor humidity display
• Outdoor temperature display in °F (supports up to three wireless sensors)
• Minimum/maximum display for temperature and humidity
• Outdoor humidity and temperature trend display
• Weather forecast symbols
• Low battery indicator
• Mold indicator
• Dew-point display
• Heat index

Wireless Sensor

• Range of up to 328 ft (100 meters) in open area
• Wall mounting bracket

Overview of Weather Station Display

The weather station display shows various readings and indicators:

• 1. Illumination backlight
• 2. Outdoor temperature
• 3. Max/Min outdoor temperature/humidity
• 4. Outdoor humidity
• 5. Outdoor humidity trend (indicated by arrows: ⬆️ rising, ➡️ constant, ⬇️ falling)
• 6. Outdoor index (e.g., Dew point, Heat index)
• 7. Indoor humidity
• 8. Max/Min indoor temperature/humidity
• 9. Indoor temperature
• 10. Dew point
• 11. Low battery indicator for indoor unit
• 12. Weather forecast symbol
• 13. Outdoor temperature trend (indicated by arrows: ⬆️ rising, ➡️ constant, ⬇️ falling)
• 14. Current channel of outdoor sensor
• 15. Low battery indicator for outdoor sensor

Operating Elements and Parts

Base Unit

1. Operating buttons:

• INDEX Button: Switches between mold indicator, dew point, and heat index. Hold for 2 seconds to switch between °C/°F and set weather symbol mode.
• MEM Button: Displays stored MAX and MIN values.
• CH Button: Displays weather data from different wireless sensors (channels 1, 2, 3). Also used to reconnect the wireless sensor connection.

2. Hole for wall mounting

3. Detachable stand

4. Battery compartment

Wireless Sensor

1. Red pilot light

2. TX button

3. Sliding switch 1, 2, 3: Sets the sensor number (transmission channel).

4. Battery compartment

5. Loop for hanging

Note: The included wireless sensor is pre-configured. Changing the transmission channel is only necessary when adding additional sensors.

How to Set Up

Insert Batteries

1. Insert 2x AA batteries into the wireless sensor, observing correct polarity. The red LED indicator will flash during transmission.
2. Open the battery compartment of the weather station and insert 3x AAA batteries, observing correct polarity. Close the compartment. The screen will turn off after 10 seconds and requires a touch to activate.

Switch Temperature Unit (°C/°F) and Set Weather Symbol

Upon first power-up, the unit enters °C/°F selection, then weather symbol setting.

1. The °C/°F symbol will flash (default is °F). Press the INDEX button to switch between °C and °F. Press the MEM button to save.
2. After setting the temperature unit, the weather symbol will flash (default is half sunny). It adjusts automatically, but can be manually set using the INDEX button.
3. Press the INDEX button repeatedly to cycle through weather symbols: sunny, partly cloudy, overcast, rain, thunderstorm, snow, snowstorm.
4. Press the MEM button to save the weather symbol setting.

Pairing the Outdoor Sensor with the Weather Station

After installing batteries, the weather station attempts to receive RF signals from the outdoor sensor on the same channel for 3 minutes. Use the CH button on the base unit to match the correct sensor.

The sensor usually connects automatically. If not, follow these steps:

• Ensure the weather station and outdoor sensor are on the same channel.
• Long-press the CH button on the base unit to search for the sensor signal. The sensor receiving icon will flash during the search and become stable upon connection.
• The station automatically searches for the signal every 3 minutes until connected.

Note: After replacing the sensor battery, press and hold the CH button on the base unit to re-establish the connection.

Mold Indicator, Dew-point Display, and Heat Index

Press the INDEX button to cycle through these displays:

• Mold Indicator: Shows the possibility of mold growth based on temperature and humidity. Possible indicators: LOW, MED, HI.
• Dew-point Display: The temperature at which dew or mist forms. If below 32°F (0°C), "L.L.L" is displayed. If above 140°F (60°C), "H.H.H" is displayed.
• Heat Index: Displays the perceived temperature based on temperature and humidity. If outdoor temperature is below 80°F (26.7°C), the actual temperature is shown. Above 80°F (26.7°C), it's calculated by software. If above 158°F (70°C), "158°F (70°C)" is displayed.

Daily MAX/MIN Data

All MAX/MIN records reset automatically every 24 hours.

From the normal display, press and release the MEM button to view:

• MAX: Indoor and outdoor maximum temperature/humidity records.
• MIN: Indoor and outdoor minimum temperature/humidity records.

Pressing the MEM button repeatedly in normal display mode shows the current day's maximum and minimum values.

Note: Pressing and holding the MEM button clears the highest and lowest temperature and humidity values recorded since midnight.

Other Functions

Low Battery Indicator

When batteries are low, indicators 11 (indoor) or 15 (outdoor) will appear. Replace batteries promptly and restart the weather station.

Weather Trend

Temperature and humidity trends are shown by arrows: ⬆️ rising, ➡️ constant, ⬇️ falling.

Weather Forecast Icons

Icons predict weather for the next 12 hours based on barometric pressure. Allow 7-10 days for calibration. There are 7 forecast icons:

• Sunny: Clear skies.
• Partly cloudy: Some clouds.
• Overcast: Mostly cloudy.
• Rain: Rain expected.
• Thunderstorm: Thunderstorms expected.
• Snowfall: Snow expected.
• Heavy snowfall: Heavy snow expected.

Note: The forecast may not reflect current conditions. Accuracy is around 75%. If outdoor temperature is below 30.2°F (-1°C) and forecast is RAIN or T-STORM, SNOW will be displayed.

Temperature Alarm

A snowflake symbol ❄️ will flash if the wireless sensor measures a temperature between 33.8°F (1°C) and 30.2°F (-1°C), indicating frost risk. The symbol will be displayed constantly if the temperature stays below 30.2°F (-1°C) for an extended period.

Note: Frost or black ice risk exists around freezing points even if the alarm is not displayed. The outdoor sensor only measures local temperature.

How to Add Extra Sensors

The station supports up to three wireless sensors. Additional sensors are available for purchase.

Note:

1. Set different channels (1-3) for each sensor using the sliding switch near the batteries.
2. On the base unit, press and hold the CH button while the corresponding channel is displayed until the signal icon flashes to pair the new sensor.

Where the Sensor Should Be Placed

1. The sensor can be hung or placed.
2. Place under a porch or eaves for protection.
3. Ensure placement is within the maximum range of 328ft (100m) in an open area.
4. Mount the sensor vertically to allow moisture to drain correctly.

Notes:

• Building materials like reinforced concrete can block radio reception.
• Electronic devices (TVs, phones, computers) can interfere with wireless signals.
• Avoid placing the base unit or sensors directly on the floor, as this reduces range.
• Low temperatures in winter can reduce battery performance and transmitter range.

Where the Weather Station Should Be Placed

• Place on a flat surface using the stand, or mount on a wall using hanging holes.
• Position at least 6 feet away from electronic devices (cordless phones, gaming systems, TVs, microwaves, routers).
• Ensure it's within range of outdoor sensors (330 ft, 100m open air).
• Obstacles like walls, windows, stucco, concrete, and metal objects can reduce range.

Resetting the Weather Station

If incorrect values are displayed, reset to factory settings:

1. Remove batteries from both the outdoor sensor and weather station.
2. Reinsert batteries into both units.
3. Keep them within a few feet of each other for about 20 minutes to establish a strong connection.

Care and Maintenance

• Do not mix old and new batteries.
• Do not mix battery types (Alkaline, Standard, Lithium, Rechargeable).
• Use the correct battery size and grade.
• Replace all batteries in a set simultaneously.
• Clean battery contacts and device contacts before installing batteries.
• Ensure correct battery polarity (+ and -).
• Remove batteries if the equipment will not be used for an extended period.
• Promptly remove expired batteries.

Safety Precautions

Read and store these instructions. Pass them on if the device is transferred.

• This device can be used by children over 8 years old and individuals with reduced physical, sensory, or mental abilities, or lack of experience, provided they are supervised and understand the hazards.
• Keep the device away from children under 8 years of age.
• Cleaning and maintenance should only be performed by children under supervision.
• Ensure children do not play with the device.
• Do not immerse the device in water or other liquids. Avoid use in wet areas like sinks due to electric shock hazard.

Unpacking and Checking

1. Remove the device from packaging, peel off protective films, and keep packaging materials away from children.
2. Dispose of materials according to type.
3. Verify all included items are present and check the weather station for any damage.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) it must not cause harmful interference, and (2) it must accept any received interference, including that which may cause undesired operation.

WARNING: Changes or modifications not expressly approved by the responsible party for compliance may void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy. If not installed and used per instructions, it may cause harmful interference to radio communications. No guarantee of no interference in a particular installation.

If this equipment causes harmful interference to radio or television reception (verifiable by turning the equipment off and on), users are encouraged to correct interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from the receiver's.
• Consult the dealer or an experienced radio/TV technician.

Disclaimers

Unni Technology reserves the right to change product specifications. The manufacturer and supplier are not responsible for malfunctions due to interference.

Troubleshooting

Warranty and Support

Unni Technology, Ltd. provides a 1-year limited warranty from the date of purchase against manufacturing defects in materials and workmanship.

For support or before returning a product, please contact customer support at: unni_technology@hotmail.com