VIVO STAND-V002K Pneumatic Arm Dual Monitor Desk Mount Instruction Manual

Pneumatic Arm Dual Monitor Desk Mount

LAST UPDATED: 06/02/2021 REV2 Open Monday - Friday 7:00am - 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact…

Assembly Manual PDF

Monitor Mounts Stands for every desk setup – VIVO - desk solutions, screen mounting, and more Assembly Instructions

Assembly Manual PDF (2.46MB)

Original Document

If the viewer doesn’t load, open the PDF directly.

Extracted Text

Pneumatic Arm Dual Monitor Desk Mount
Instruction Manual

SKU: STAND-V002K
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. https://vivo-us.com/products/stand-v002k
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

help@vivo-us.com

www.vivo-us.com Chat live with an agent!

309-278-5303

WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER: � NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND. � USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS

A (x1) Arm

B (x2) VESA Plate

C (x1) Pole

D (x1) Clamp

E (x1) Cable Clip

F (x1) Grommet
Base
K (x1) 4mm Allen
Wrench

G (x1) Soft Pad

H (x1) Support Plate

I (x2) Thumbscrew

J (x3) M6x16

L (x1) 6mm Allen
Wrench

M-A (x8) M4x12

M-B (x8) M4x16

M-C (x8) M5x12

M-D (x8) M5x16

M-E (x8) D5 Washer

TOOLS NEEDED

Phillips Screwdriver
2

M-F (x8) Spacer

NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

DO NOT EXCEED WEIGHT CAPACITY.

2.2-19.8lbs

Failure to do so may result in serious injury.

(1-9kg)

PER MONITOR

ASSEMBLY STEPS
STEP 1
Loosen the screws and disassemble the Clamp (D) using the 4mm Allen Wrench (K).

K

STEP 2
OPTION A: Clamp Installation Attach clamp brace (D1) to the Pole (C) using the M6x16 bolts (J) and the 4mm Allen Wrench (K). Peel the protective film off of the Soft Pad (G) and place it onto the clamp brace (D1).

OPTION B: Grommet Base Installation For grommet hole attachment only, cut the Soft Pad (G) along the indentations. Peel the protective film off of the Soft Pad (G) and place the pieces onto the Grommet Base (F) as shown below.

K

C

3

STEP 2 (Continued)
OPTION A: Clamp Installation For thinner desktops, re-attach the Clamp (D2) to the Clamp Brace (D1) and tighten the screws using the 4mm Allen Wrench (K). For thicker desktops, disassemble the Clamp (D2) using a Phillips screwdriver as shown in 3.1. Flip the L-bracket over and reassemble. Then re-attach the Clamp (D2) to the Clamp Brace (D1) and tighten the screws using the 4mm Allen Wrench (K).

OPTION B: Grommet Installation If not using an existing through-hole, using a 10mm (") drill bit, drill through the desktop at least 2" away from the edge. Disassemble the Clamp (D2) using a Philips screwdriver. Set aside all parts except for Clamp Bolt (D3). Attach Pole (B) and Grommet Base (F) to the desktop using the Support Plate (H) and Clamp Bolt (D3) as shown below.

D1
K
3.1

K

B

F

While holding Arm (A) closed, cut the shipping tie and gently release (A).

4

STEP 3
Slide Arm (A) onto Pole (B) and tighten using 6mm Allen Wrench (L). Attach Cable Clip (E) to Pole (C).

A L
E

L C

STEP 4
Attach VESA Plate (B) to the back of the monitor using Screws (M-A through M-D) and Washers (M-E). If needed, use Spacers (M-F).

STEP 5
Slide VESA Plate (B) with monitor over bracket on Arm (A). Secure using the Thumbscrew (I).

B B

A
5

STEP 6

Adjust gas spring support in Arm (A) using 6mm Allen wrench (L). Turning counter-clockwise increas-

es support, and clockwise decreases.

L

A

STEP 7
Remove bottom cover from Arm (A) by sliding it off. Organize cables and re-attach cover.
A
6

STEP 8
Adjust tilt support using 6mm Allen Wrench (L). Store Allen Wrenches (K and L) in Cable Clip (E). Adjust as desired.
L
L K
7

Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us

LAST UPDATED: 06/02/2021 REV2

Open Monday - Friday 7:00am - 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

309-278-5303

AVG. RESOLUTION TIME (within office hrs): 5M 4S

www.vivo-us.com
Chat live with an agent!

AVG. RESOLUTION TIME (within office hrs): < 15 M

help@vivo-us.com

AVG. RESPONSE TIME (within office hrs): 1HR 8M - 23% within < 15m - 38% within < 30m - 61% within < 1hr - 83% within < 2hr - 92% within < 3hr

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com