Wanbo T6 Max Projector User Manual and Safety Guide

Important Safety Precautions

To achieve the best effect, it is recommended to use the projector in a dark room.

1. Please do not install in places directly blown by cold and warm air of air-conditioning, as water condensation or high temperature may lead to failure of the machine.
2. Ensure adequate ventilation and do not block the heat radiation outlets to prevent heat accumulation inside the machine.
3. Please prevent foreign matters such as paper scraps from falling into the machine. Do not insert any metals such as iron wire or screwdriver into the machine. If any foreign matters fall into the body, please turn off the power immediately and turn to a professional technician for removal.
4. Do not place any liquid on this machine to avoid the risk of electric leakage.
5. Please use soft packaging materials to move the projector. Install the lens protection cover to protect the lens from scraping. In addition, keep the projector from violent vibration.
6. Areas near the exhaust will become hot during and after operation; touching them may lead to scald.
7. Please do not watch the lens directly when it is on, so as to protect your eyes from damage.

Projector Part Name and Function

[!] Do not install in places with poor ventilation.

• Handle: For carrying the projector.
• Remote control Signal Receiving Window: Receives signals from the remote control.
• Heat Radiation Outlet: [!] Do not block. Essential for cooling.
• Power Supply Input: Connects to the power adapter.
• Adapter: Converts power for the projector.
• Focus Key: Used for adjusting focus.
• Voice Key: Activates voice control features.

Installation and Adjustment

1. Device Power-On and Power-Off

Power-On:

• Method 1: Press the [power button] on the projector to start.
• Method 2: Point the [remote control] to the projector and press the [power key] to turn it on.

Shut Down: Short press the [power button] or the "[ON/OFF]" key on the [remote control]. Once a [shut down prompt box] appears, short press the [power button] or the [power key] on the [remote control] again.

2. Adjust Focal Length

When the picture image is blurred (indicated as a blurred image schematic), adjust the lens focus using the [Focus Key] on the [remote control] to achieve the best definition.

Basic Parameters

Notes:

• Do not open the shell to prevent [electric shock]. Please turn to qualified professional maintenance personnel for repair; do not attempt self-repair as there are no user-serviceable parts inside the machine.
• Do not expose the machine to [rain or moisture] so as to prevent misfire or [electric shock].
• Do not block the [vent] (Inlet or Outlet).
• Do not install in [dusty and smoky] environments.
• [Heat Radiation Outlet] [!] Do not block.
• [Power Supply Input]

Mobile Phone with the Same Screen

The following steps help display content from your mobile phone to the projection screen synchronously through [wireless] mirroring. Enjoy a [larger picture] (Applicable for [intelligent Android version] only).

[Equipment requirements:] Support devices above [IOS] 6 and [Android] 5.3 Min.

IOS Devices User Instruction

1. Ensure the Phone and Projector are under the same [WIFI] (For [IOS] Only).
2. Open [Eshare] of the projector.
3. Open "[AirPlay]" "[Mirror]" of the Phone.
4. Choose the device name with [Eshare] to complete [mirroring].

Android Devices User Instruction

1. Ensure the Phone and Projector are under the same [WIFI] (For [Android] Only).
2. Open [Eshare] of the projector.
3. Choose the device name with [Eshare] to complete mirroring.

Mobile Phone with the Same Screen (iPhone under status of No WIFI)

1. If there is no [WIFI], firstly open the [4G network] of iPhone, then open a [WIFI hot spot] in the "[Settings]" interface of the phone.
2. Collect iPhone's hot spot [WIFI] for the projector.
3. Open "[Eshare]".
4. Open "[Airplay]"/"[Screen Mirror]".
5. Find the projector and click.

How to "push" contents to the projector

If you want to [return] to the previous layer, please press the [Return] key. If you want to [return] to the main interface, please press the [Return] key.

1. Ensure the Phone and Projector are under the same [WIFI].
2. Open video software on your mobile phone and find the [TV push icon] (it's usually on the top right or on the bottom right) (Each [APP] has a different [push icon design]).
3. Click this icon to [push videos] to the projector. The phone can still be used normally, it will have no [conflict].

[Note:] Not all video software have the function of push. Specific operation contents are subject to actual situation due to irregular updates.

Signal Source Setting

Enter the [Setting] interface main screen and select [input source]. Enter into [AV/HDMI signal channel], press "[OK]" to switch [input source].

Projection Distance Reference

[Note:] Projection size and distance are calculated according to projection ratio, which may have a deviation and subject to actual status.

Cleaning Method

Please make sure the [power plug is unplugged] before cleaning.

Clean the Projector

1. Wipe with a [soft, dry cotton cloth]. If it's dirtied seriously, we can wipe with a soft cloth that is stuck with [diluted neutral detergent], then dry with a clean and dry cloth. Please pay more attention if used with [chemical fiber cloth].
2. Do not use [thinner, benzene or any other solvents] to avoid quality reduction or [coating peeling off] etc.
3. A [brush] can be inserted into the front of the [vacuum cleaner] to remove dirt inside the vents. Please do not use the [vacuum cleaner] directly.
4. Please do not scrape the machine with [nails or any other hard objects] so as to avoid [scratches].

Lens Cleaning

1. Clean the lens with the same method for a [camera lens]: please use a [professional blow dryer] or [cleaning paper for glasses], ensure the lens is not [scratched].

Inlet and Outlet Dust Cleaning

1. Dust in the [inlet and outlet] will prevent [ventilation] and increase the [internal temperature], which will cause [defect].
2. Disconnect the [power line] after turning off the projector.
3. Clean the [exterior] with an [electric vacuum cleaner]. Please install a [brush head adapter] on the [vacuum cleaner] first. Kindly take note: do not use a [vacuum cleaner] without a [connector] or [brush].

Poisonous and Harmful Substance, Element Name and Content

[Note:] Content of the hazardous substance in all homogeneous materials of the product system is under the limits of SJ/T11363-2006.

[Content of the hazardous substance exceeds the limit requirements.]

The components labeled "X" have no substitutive due to global technology development limits. The number "10" in the logo represents the normal environmental service life of the product. ([Battery Excluded])

Warranty Card

1. We offer "[three guarantees]" for this product. [One year warranty] for [non-artificial damaged] items since purchasing (subject to [purchase record]).

2. We will provide [warranty service] for any default caused by [product technical reasons] during the [warranty period].

3. The following situations are out of the range of guarantee:

• [Accessories out of the mainframe]
• [Unauthorized disassembly and repair without consent].
• Damage caused by [external force and other natural disasters].

4. Please keep this card and contact your [distributor] when products have [quality problem].

5. This warranty is limited to product maintenance during the [warranty period]; no other liability.

Customer Information:

Customer Name:

Customer ID:

Purchase of Shop:

Customer Tel:

Fault Description (Please describe in detail for quick maintenance):

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

[Caution]: Any changes or modifications to this device not explicitly approved by [manufacturer] could void your authority to operate this equipment.

This equipment complies with FCC radiation exposure limits set forth for an [uncontrolled environment]. This equipment should be installed and operated with [minimum distance 20cm] between the radiator and your body.

Important Notes

[CAUTION:] Possibly hazardous optical lamp. May be harmful to the eyes [!] at operating lamp.

[CAUTION:] UV emitted from this product. Eye or skin irritation may occur [!] Use appropriate shielding.

[CAUTION:] IR emitted from this product. Do not look directly at operating lamp. May be harmful to the eyes.