Mitsubishi Electric FR-E700 Series Variable Speed Control Inverters

The cost-effective variable speed control solution for general purpose applications.

Key Features

Available in 115V, 240V, and 480V up to 20HP.
Advanced Magnetic Flux Vector Control for improved starting torque and smooth low-speed motor operation.
Auto-tuning allows improved performance with virtually any manufacturer's motor.
All capacities include a built-in brake chopper.
Safety Stop Function meets EN954-1 Category 3 and IEC60204-1 Stop Category 0.
USB Communications for fast commissioning and troubleshooting.
Standard RS-485 Serial Communications supporting Modbus® RTU.
Sink / Source selectable I/O.
Supports remote I/O function via network.
Built-in PID Control.
Delivers rated current at 50°C and 14.5kHz carrier frequency with minimal de-rating.
200% overload for 3 seconds.
0 to 10V analog output.
Supports CC-Link®, DeviceNet™™, Profibus® DP, LONWORKS®, EtherNet/IP™™.
Standard 5-year warranty.

Specifications Overview

FR-E700 Series Max Load Capacity, Capacity, and Safety
Voltage Class	Phase	HP	Max Load Capacity (Amps)	Inverter Capacity (Amps)	Safety Version (3-phase only)
115V	1 Phase	1/8 - 1 Hp	(E710W*)	10 (17.5A output)	SC
240V	1 Phase	1/8 - 3 Hp	(E720S)*
208/230V	3 Phase	1/8 - 20 Hp	(E720)
460V	3 Phase	1/2 - 20 Hp	(E740)

*Contact MEAU for SC version availability.

FR-E700 Series Dimensions and Specifications

FR-E700 Series Model Specifications
HP	Output Amps	Model Number	Dimensions (inches)	Weight Lbs (kg)	Stocked Item
			Height \| Width \| Depth
1-Phase 100~120VAC Input / 3-Phase 200~240VAC Output
1/8	0.8	FR-E710W-008-NA	5.0 (128) \| 2.7 (68) \| 3.2 (80.5)	1.1 (0.5)	S
1/4	1.5	FR-E710W-015-NA	5.0 (128) \| 2.7 (68) \| 4.4 (110.5)	1.3 (0.6)	S
1/2	3	FR-E710W-030-NA	5.0 (128) \| 2.7 (68) \| 4.5 (112.5)	2.0 (0.9)	S
1	5	FR-E710W-050-NA	5.0 (128) \| 6.7 (170) \| 6.1 (155)	7.5 (3.4)	S
1-Phase 200~240VAC Input / 3-Phase 200~240VAC Output
1/8	0.8	FR-E720S-008-NA	5.0 (128) \| 2.7 (68) \| 3.2 (80.5)	1.1 (0.5)	S
1/4	1.5	FR-E720S-015-NA	5.0 (128) \| 2.7 (68) \| 3.2 (80.5)	1.1 (0.5)	S
1/2	3	FR-E720S-030-NA	5.0 (128) \| 2.7 (68) \| 6.2 (157.6)	1.3 (0.6)	S
1	5	FR-E720S-050-NA	5.0 (128) \| 4.3 (108) \| 5.4 (135.5)	3.1 (1.4)	S
2	8	FR-E720S-080-NA	5.0 (128) \| 4.3 (108) \| 6.4 (161)	3.1 (1.4)	S
3	11	FR-E720S-110-NA	5.9 (150) \| 5.5 (140) \| 6.2 (155.5)	4.2 (1.9)	S
3-Phase 200~240VAC Input & Output
1/8	0.8	FR-E720-008SC-NA	5.0 (128) \| 2.7 (68) \| 3.4 (87)	1.1 (0.5)	S
1/4	1.5	FR-E720-015SC-NA			S
1/2	3	FR-E720-030SC-NA	5.0 (128) \| 2.7 (68) \| 4.7 (120)	1.6 (0.7)	S
1	5	FR-E720-050SC-NA	5.0 (128) \| 2.7 (68) \| 5.5 (139)	2.2 (1.0)	S
2	8	FR-E720-080SC-NA	5.0 (128) \| 4.3 (108) \| 5.6 (142)	3.1 (1.4)	S
3	11	FR-E720-110SC-NA			S
5	17.5	FR-E720-175SC-NA	5.0 (128) \| 6.7 (170) \| 5.9 (149)	3.8 (1.7)	S
7 1/2	24	FR-E720-240SC-NA			S
10	33	FR-E720-330SC-NA	10.3 (260) \| 7.1 (180) \| 6.9 (171)	9.5 (4.3)	S
15	47	FR-E720-470SC-NA	10.3 (260) \| 8.7 (220) \| 7.7 (196)	19.9 (9)	S
20	60	FR-E720-600SC-NA			S
3-Phase 380~480VAC Input & Output
1/2	1.6	FR-E740-016SC-NA	5.9 (150) \| 5.5 (140) \| 4.7 (120)	3.1 (1.4)	S
1	2.6	FR-E740-026SC-NA			S
2	4	FR-E740-040SC-NA			S
3	6	FR-E740-060SC-NA	5.9 (150) \| 5.5 (140) \| 5.6 (142)	4.2 (1.9)	S
5	9.5	FR-E740-095SC-NA			S
7 1/2	12	FR-E740-120SC-NA	5.9 (150) \| 8.7 (220) \| 6.0 (153)	7.1 (3.2)	S
10	17	FR-E740-170SC-NA			S
15	23	FR-E740-230SC-NA	10.3 (260) \| 8.7 (220) \| 7.7 (196)	19.9 (9)	S
20	30	FR-E740-300SC-NA			S

Control Specifications

Control Specifications Summary
Specification	Details
Control Method	Soft-PWM control/high carrier frequency PWM control (V/F control, Advanced magnetic flux vector control, General-purpose magnetic flux vector control, Optimum excitation control are available)
Output Frequency Range	0.2 to 400Hz
Frequency Setting Resolution	Analog Input: 0.06Hz/60Hz (terminal 2, 4: 0 to 10V/10bit), 0.12Hz/60Hz (terminal 2, 4: 0 to 5V/9bit), 0.06Hz/60Hz (terminal 4: 0 to 20mA/10bit) Digital Input: 0.01Hz
Frequency Accuracy	Analog Input: Within ±0.5% of the max. output frequency (25°C ±10°C) Digital Input: Within 0.01% of the set output frequency
Voltage/Frequency Characteristics	Base frequency can be set from 0 to 400Hz, Constant-torque/variable torque pattern can be selected
Starting Torque	200% or more (at 0.5Hz) when Advanced magnetic flux vector control is set (3.7K or less)
Torque Boost	Manual torque boost
Accel/Decel Time Setting	0.01 to 360s, 0.1 to 3600s (acceleration and deceleration can be set individually), linear or S-pattern accel/decel modes are available.
DC Injection Brake Operation	Frequency (0 to 120Hz), operation time (0 to 10s), operation voltage (0 to 30%) can be changed.
Stall Prevention Operation Level	Operation current level can be set (0 to 200% adjustable), whether to use the function or not can be selected

Operation Specifications

Operation Specifications Summary
Specification	Details
Frequency Setting Signal	Analog Input: Two terminals (Terminal 2: 0 to 10V, 0 to 5V selectable; Terminal 4: 0 to 10V, 0 to 5V, 4 to 20mA selectable) Digital Input: Entered from operation panel or parameter unit. Frequency setting increment can be set. 4 digit BCD or 16bit binary data (with FR-A7AX E kit).
Start Signal	Forward and reverse rotation or start signal automatic self-holding input (3-wire input) can be selected.
Input Signal (Standard/Safety Stop)	Standard (Control circuit terminal model: Seven terminals) / Safety stop function model (Six terminals). Signals can be assigned to Pr. 178 to Pr.184 for functions like multi-speed selection, remote setting, stop-on contact, PID control, brake opening signal, external thermal input, etc.
Operational Functions	Maximum/minimum frequency setting, frequency jump, external thermal relay input, auto-restart after power failure, forward/reverse rotation prevention, remote setting, brake sequence, multi-speed operation, stop-on contact, droop control, regeneration avoidance, slip compensation, operation mode selection, offline auto tuning, PID control, computer link operation (RS-485).
Safety stop function (*1)	Safety shutoff signal input from terminals S1 and S2 (compliant with EN954-1 Cat.3).

Output Signal Specifications

Output Signal Summary
Specification	Details
Output Signal Points	Open Collector Output: Two terminals Relay Output: One terminal
Operating Status	Signals can be assigned to Pr.190 to Pr.192 for functions like inverter operation, overload alarm, output frequency detection, regenerative brake prealarm, electronic thermal relay prealarm, inverter operation ready, etc.
For Meter Output Points	Analog Output: 0 to 10VDC (one terminal)
For Meter Indication	Signals can be assigned to Pr.158 AM terminal for output frequency, motor current, output voltage, frequency setting, motor torque, converter output voltage, PID set point, PID measured value, etc.
Operation Panel / Parameter Unit (FR-PU07)	Displays operating status such as output frequency, motor current, output voltage, frequency setting, cumulative energization time, actual operation time, motor torque, PID set point, PID measured value, PID deviation, etc. Past fault definitions (up to 8) are stored.
Interactive Guidance Function (help) (*2)	Provides an operation guide.

Protective and Warning Functions

Protective and Warning Functions
Category	Functions
Protective Function	Overcurrent (acceleration, constant speed, deceleration), overvoltage (acceleration, constant speed, deceleration), inverter protection thermal operation, motor protection thermal operation, heatsink overheat, input phase failure (4), output side earth fault, output phase failure, external thermal relay operation (3), option fault (3), parameter error, internal board fault, PU disconnection, retry count excess (4), CPU fault, brake transistor alarm, inrush resistance overheat, communication error, analog input error, USB communication error, brake sequence error (3), safety circuit fault (1).
Warning Function	Fan alarm, overcurrent stall prevention, overvoltage stall prevention, PU stop, parameter write error, regenerative brake prealarm (3), electronic thermal relay function prealarm, maintenance output (3), undervoltage, operation panel lock, password locked, inverter reset, safety stop (*1).

Environment Specifications

Environmental Conditions
Specification	Details
Ambient Temperature	-10°C to +50°C (14°F to 122°F) (non-freezing) (*5)
Ambient Humidity	90%RH maximum (non-condensing)
Storage Temperature (*6)	-20°C to +65°C (-4°F to 149°F)
Atmosphere	Indoors (without corrosive gas, flammable gas, oil mist, dust and dirt etc.)
Altitude/Vibration	Maximum 1000m (3280.80 feet) above sea level, 5.9m/s² or less at 10 to 55Hz (directions of X, Y, Z axes)

Notes:

(*1) This function is only available for the safety stop function model.
(*2) This operation guide is only available with option parameter unit (FR-PU07).
(*3) This protective function does not function in the initial status.
(*4) This protective function is available with the three-phase power input model only.
(*5) When using the inverters at the surrounding air temperature of 40°C (104°F) or less, the inverters can be installed closely attached (0cm clearance).
(*6) Temperatures applicable for a short time, e.g. in transit.

FR-E700 Series Plug-In Options

FR-E700 Series Plug-In Options
Model Number	Description	Stocked Item
FR-A7NC E KIT SC	CC-Link® Network Option	S
FR-A7ND E KIT SC	DeviceNet™™ Network Option	S
FR-A7NP E KIT SC	PROFIBUS® DP Network Option	S
FR-A7NL E KIT SC	LONWORKS® Network Option	S
FR-A7AX E KIT SC	Additional 16-bit Digital Input	S
FR-A7AY E KIT SC	Additional Analog & Digital Output	S
FR-A7AR E KIT SC	Additional Relay Output	S

FR-E700 Series External Options

FR-E700 Series External Options
Model Number	Description	Stocked Item
FR-PU07	Alpha-Numeric multi-language keypad	S
FR-PU07BB-L	Battery powered Alpha-Numeric multi-language keypad	S
FR-CB20	Keypad extension cable	S
SC-FRPC	Serial communications cable	S
FR-ABR-__K	External brake resistor	S
FR-RJ45-HUB4	Serial Network Hub - 2 Stations	S
FR-RJ45-HUB10	Serial Network Hub - 8 Stations	S
FR-RJ45-TR	Terminating Resistor For FR-RJ45-HUB Communication	S

Note: FR-E7TR is not compatible with safety version of E700.

FR-E700 Dynamic Braking

Mitsubishi Electric VFDs have inherent braking capability. During controlled deceleration, motor regenerative losses are dissipated in the motor, wire, and VFD circuitry. The built-in DC injection braking allows for low-speed braking and stopping.

When these capabilities are inadequate, a power transistor brake unit and resistor unit in series across the DC bus are necessary. Motor regeneration increases DC bus voltage, and when it exceeds a threshold, the transistor activates, passing current through the resistor to dissipate motor kinetic energy as heat. VFD overcurrent and overvoltage protective circuits are always active and will fault-trip the VFD if the brake size is inadequate.

Key factors for sizing brakes include the effective duty cycle (%ED) and the short-time duty rating. The effective duty cycle increases with an external resistor. Profiling the effective duty cycle over time helps determine the short-time duty and calculate %ED.

%ED Calculation: %ED = Braking time / total time for complete operating cycle * 100

Example: A complete cycle includes 5 sec acceleration, 60 sec run time, 3 sec deceleration, and 12 sec stopped time. %ED = 3 / (5 + 60 + 3 + 12) * 100 = 3.6%

The tables assume 100% brake torque relative to the motor's rated torque. Torque (kg.m) = 974 x Power (kW) / Speed (rpm).

240VAC Dynamic Braking Resistor at 100% Braking Torque

240VAC Dynamic Braking Resistors
Resistor Kit Model	Weight kg (lbs)	Resistance (Ohms)	Continuous Power (W)	Drive Model (Hp)	Stocked Item % ED
FR-ABR-0.4K	0.2 (0.5)	200	60	1/2 (E710W and E720(S))	10% S
FR-ABR-0.75K	0.4 (0.9)	100	80	1 (E710W and E720(S))	10% S
FR-ABR-2.2K	0.5 (1.1)	60	120	2 & 3 (E710W and E720(S))	10% S
FR-ABR-3.7K	0.8 (1.8)	40	155	5 (E710W and E720(S))	10% S
FR-ABR-5.5K	1.3 (2.9)	25	185	7 1/2 (E710W and E720(S))	10% S
FR-ABR-7.5K	2.2 (4.9)	20	340	10 (E710W and E720(S))	10% S
FR-ABR-11K	3.4 (7.5)	13	560	15 (E710W and E720(S))	6% S
FR-ABR-15K (2 resistors in parallel)	2.4 (5.3) x 2	9 (18/2)	805	20 (E710W and E720(S))	6% S

480VAC Dynamic Braking Resistor at 100% Braking Torque

480VAC Dynamic Braking Resistors
Resistor Kit Model	Weight kg (lbs)	Resistance (Ohms)	Continuous Power (W)	Drive Model (Hp)	Stocked Item % ED
FR-ABR-H0.4K	0.2 (0.5)	1200	45	1/2 (E740)	10% S
FR-ABR-H0.75K	0.2 (0.5)	700	75	1 (E740)	10% S
FR-ABR-H1.5K	0.4 (0.9)	350	115	2 (E740)	10% S
FR-ABR-H2.2K	0.5 (1.1)	250	120	3 (E740)	10% S
FR-ABR-H3.7K	0.8 (1.8)	150	155	5 (E740)	10% S
FR-ABR-H5.5K	1.3 (2.9)	110	185	7 1/2 (E740)	10% S
FR-ABR-H7.5K	2.2 (4.9)	75	340	10 (E740)	10% S
FR-ABR-H11K	3.4 (7.5)	52	530	15 (E740)	6% S
FR-ABR-H15K (2 resistors in series)	2.4 (5.3) x 2	36 (18 x 2)	870	20 (E740)	6% S

Brake Resistors Dimensions

Brake Resistor Dimensions (mm)
Brake Resistor Model	Dimensions (mm)	Stocked Item
	L \| W1 \| W2 \| D \| H
200V Class
FR-ABR-0.4K	140 \| 125 \| 100 \| 40 \| 21	S
FR-ABR-0.75K	215 \| 200 \| 175 \| 40 \| 21	S
FR-ABR-2.2K	240 \| 225 \| 200 \| 50 \| 26	S
FR-ABR-3.7K	215 \| 200 \| 175 \| 61 \| 33	S
FR-ABR-5.5K	335 \| 320 \| 295 \| 61 \| 33	S
FR-ABR-7.5K	400 \| 385 \| 360 \| 80 \| 40	S
FR-ABR-11K	400 \| 385 \| 360 \| 100 \| 50	S
FR-ABR-15K (*1)	300 \| 285 \| 260 \| 100 \| 50	S
400V Class
FR-ABR-H0.4K	115 \| 100 \| 75 \| 40 \| 21	S
FR-ABR-H0.75K	140 \| 125 \| 100 \| 40 \| 21	S
FR-ABR-H1.5K	215 \| 200 \| 175 \| 40 \| 21	S
FR-ABR-H2.2K	240 \| 225 \| 200 \| 50 \| 26	S
FR-ABR-H3.7K	215 \| 200 \| 175 \| 61 \| 33	S
FR-ABR-H5.5K	335 \| 320 \| 295 \| 61 \| 33	S
FR-ABR-H7.5K	400 \| 385 \| 360 \| 80 \| 40	S
FR-ABR-H11K	400 \| 385 \| 360 \| 100 \| 50	S
FR-ABR-H15K (*2)	300 \| 285 \| 260 \| 100 \| 50	S

Notes:

(*1) For the 15K, connect the two supplied resistors (18 ohms) in parallel.
(*2) For the H15K, connect the two supplied resistors (18 ohms) in series.

Input Radio Noise Filter

This filter is connected to the input of the drive and helps to reduce radiated noise in the radio frequencies.

FR-E740 EMC Filters
Drive Voltage Number	Kit Model	Leakage Current (mA)	Dimensions mm (in)	Drive Model	Stocked Item
			L \| W \| D
208-230	FR-BIF	4	58 (2.3) \| 44 (1.8) \| 42 (1.7)	E740-016 to 040	S
460	FR-BIF-H	4	58 (2.3) \| 44 (1.8) \| 42 (1.7)	E740-060/095	S
				E740-120/170	-
				E740-230/300	-

Line Noise Filter

Provides a toroid for line noise reduction.

Line Noise Filter
Drive Hp	Kit Model Number	Dimensions mm (in)	Stocked Item
		L \| W \| D
0.5-5	FR-BSF01	110 (4.33) \| 22.5 (0.89) \| 65 (2.56)	S
0.5-75	FR-BLF	180 (7.07) \| 31.5 (1.24) \| 83 (3.27)	S

Building Management Options

Building Management Options
Network Type/Model	Stocked Item
BACnet/IP (A7NETH-2P)	X
EtherNet/IP™ (FR-A7N-XLT)	X
Modbus® TCP	X
PROFINET® 10	X
BACnet® MS/TP	X
Metasys® N2	X
Siemens FLN (P1)	X

Note: FR-E700 Series inverters require optional cover (P/N: A7A-EKITCVR-SC) for direct attachment.

DIN Rail Mounting Attachment

This attachment allows the FR-E700 Series inverter to mount on a 35mm DIN rail.

DIN Rail Mounting Attachment
Model Number	Drive Model FR-E720 (*1)	Stocked Item
FR-UDA01	008-050	S
FR-UDA02	080-110	S
FR-UDA03	175	S

Note 1: Not available for 400V models.

Installation Interchange Attachment

This attachment allows the FR-E700 Series inverter to be mounted using the installation holes from the previous series VFDs.

Installation Interchange Attachment
Model Number	Installation Model E700 Series	Previous Model E500 Series	A0x4 Series	Z024 Series	A200E Series	Stocked Item
FR-E5T-10	E720-008	FR-A024-0.1K-UL	FR-Z024-0.1K-UL			S
	E720-015	FR-A024-0.2K-UL	FR-Z024-0.2K-UL
FR-E5T-11	E720-030	FR-A024-0.4K-UL	FR-Z024-0.4K-UL
	E720-050	FR-A024-0.75K-UL	FR-Z024-0.75K-UL
FR-E5T-02	E720-080	FR-A024-1.5K-UL	FR-Z024-1.5K-UL
	E720-110	FR-A024-2.2K-UL	FR-Z024-2.2K-UL
FR-E5T	E720-175	Direct Replacement	FR-A024-3.7K-UL	FR-Z024-3.7K-UL	FR-A220E-5.5K-UL
	E720-240			FR-A220E-7.5K-UL
FR-E5T-14	E720-330		FR-A044-0.4K-UL
	E740-016	Direct Attachment	FR-A044-0.75K-UL
	E740-026		FR-A044-1.5K-UL
	E740-040		FR-A044-2.2K-UL
	E740-060		FR-A044-3.7K-UL
	E740-095

FR-E700 Installation Interchange Attachment

This attachment allows the FR-E700 Series inverter to be mounted at a 90° angle so that the depth is reduced to 80 mm.

FR-E700 Installation Interchange Attachment
Model Number	Installation Model FR-E700 Series	Previous Model FR-E500 Series	A0x4 Series	Z024 Series	Stocked item
FR-E5T-L	E720-030 E720-050	Direct Replacement	FR-A024-0.4K-UL FR-A024-0.75K-UL	FR-Z024-0.4K-UL FR-Z024-0.75K-UL	S

FR-E700 Series Watt Loss and Efficiency Data

FR-E700 Series Watt Loss and Efficiency Data
115VAC 1-Phase Input				240VAC 1-Phase Input				240VAC 3-Phase Input				480VAC 3-Phase Input
HP-CT	Model Number	Rated Watts	Watts Loss	Efficiency	Model Number	Rated Watts	Watts Loss	Efficiency	Model Number	Rated Watts	Watts Loss	Efficiency	Model Number	Rated Watts	Watts Loss	Efficiency
1/8	FR-E710W-008	100	14	86%	FR-E720S-008	100	14	86%	FR-E720-008	100	14	86%	FR-E740-016	400	45	89%
1/4	FR-E710W-015	200	20	90%	FR-E720S-015	200	20	90%	FR-E720-015	200	20	90%	FR-E740-026	750	50	93%
1/2	FR-E710W-030	400	38	91%	FR-E720S-030	400	32	92%	FR-E720-030	400	32	92%	FR-E740-040	400	32	92%
1	FR-E710W-050	750	50	93%	FR-E720S-050	750	50	93%	FR-E720-050	750	50	93%	FR-E740-050	750	50	93%
2	FR-E710W-080	1500	80	95%	FR-E720S-080	1500	80	95%	FR-E720-080	1500	85	94%	FR-E740-060	1500	85	94%
3	FR-E710W-110	2200	110	95%	FR-E720S-110	2200	100	95%	FR-E720-110	2200	100	95%	FR-E740-095	2200	100	95%
5					FR-E720S-175	3700	160	96%	FR-E720-175	3700	160	96%	FR-E740-120	3700	160	96%
7.5					FR-E720S-240	5500	290	95%	FR-E720-240	5500	310	94%	FR-E740-170	5500	310	94%
10					FR-E720S-330	7500	380	95%	FR-E720-330	7500	420	94%	FR-E740-230	7500	420	94%
15					FR-E720S-470	11000	520	95%	FR-E720-470	11000	560	95%	FR-E740-300	11000	560	95%
20					FR-E720S-600	15000	600	96%	FR-E720-600	15000	640	96%

General Notes:

The amount of heat generated by the inverter is based on one inverter connected to one motor of the same capacity.
The amount of heat generated in the above table is the amount of heat generated when the inverter is operated at its rated current.
The amount of heat generated will decrease according to the motor load and usage (duty).

Conduit Kits

Conduit Kits
Model Number	Description	Stocked Item
CK-5567	Conduit Kit for E740-026/095SC	S
CK-27	Conduit Kit for E720-030/050SC	S
CK-87	Conduit Kit for E740-120/170SC	S

FR-E700 Heatsink Extension Kits

FR-E700 Heatsink Extension Kits
Model Number	Description	Stocked Item
FR-E7CN-02	Heatsink Extension kit for E720-030	S
FR-E7CN-03	Heatsink Extension kit for E720-050	S
FR-E7CN-04	Heatsink Extension kit for E720-080/110	S
FR-E7CN-05	Heatsink Extension kit for E740-016/026	S
FR-E7CN-06	Heatsink Extension kit for E740-040/060/095	S
FR-E7CN-07	Heatsink Extension kit for E720-175	S
FR-E7CN-08	Heatsink Extension kit for E740-120/170	S
FR-E7CN-09	Heatsink Extension kit for E720-240/330	S
FR-A7CN02	Heatsink Extension kit for E720-470/600 E740-230/300	S

	Mitsubishi Electric FR-F800 Series Inverters Pocket Reference Guide A concise reference guide for Mitsubishi Electric FR-F800 Series Inverters, detailing model numbers, specifications, and peripheral equipment selection for various voltage and horsepower ratings.
	Mitsubishi Electric FR-D720-11K Inverter Datasheet \| Specifications and Compatibility Comprehensive material fact sheet for the Mitsubishi Electric FR-D720-11K compact inverter. Details technical specifications, dimensions, weight, environmental compliance, conformity, spare parts, and compatible products.
	Mitsubishi Electric FR-F840-00470-E2-60 Inverter: Material Fact Sheet Comprehensive material fact sheet detailing the specifications, dimensions, conformity, and compatible accessories for the Mitsubishi Electric FR-F840-00470-E2-60 FA-Inverter.
	Mitsubishi Electric FR-E800 Series Inverter Instruction Manual (Connection) Comprehensive guide for Mitsubishi Electric FR-E800 series inverters, covering connection, installation, wiring, safety precautions, and specifications for 200V and 400V classes. Essential reading for proper setup and operation.
	Mitsubishi Electric FR-E800 Series Inverter Instruction Manual (Function) This instruction manual provides comprehensive guidance for Mitsubishi Electric's FR-E800 series inverters, detailing their functions, operation, parameters, control methods, and settings for models like FR-E820, FR-E840, and FR-E860.
	Mitsubishi Electric 87245 FR-BAL-B-5,5K AC Main Supply Choke - Material Fact Sheet Detailed material fact sheet for the Mitsubishi Electric 87245 FR-BAL-B-5,5K AC Main Supply Choke, including technical specifications, dimensions, weight, stock data, and export information.
	Mitsubishi Electric FR-A840-01800-E2-60CRN FA-Inverter - Technical Specifications Material Fact Sheet detailing the specifications, dimensions, compatible products, and spare parts for the Mitsubishi Electric FR-A840-01800-E2-60CRN FA-Inverter, designed for crane applications.
	Mitsubishi Electric FR-E740-300SC-ENE Inverter - Material Fact Sheet Material fact sheet for the Mitsubishi Electric FR-E740-300SC-ENE inverter, detailing technical specifications, dimensions, weight, environmental compliance, and product lifecycle information.