Shark NV352 Roller Brush Replacement
guide 98261 en Shark NV352 Roller Brush Replacement
Guide ID: 98261 - Draft: 2017-12-15
Shark NV352 Roller Brush Replacement
This guide will walk you through the steps to take if you need to replace your roller brush on your vacuum.
Written By: Amy Moran
This document was generated on 2020-11-28 06:02:06 AM (MST).
© iFixit -- CC BY-NC-SA
www.iFixit.com
Page 1 of 7
Shark NV352 Roller Brush Replacement
INTRODUCTION
Guide ID: 98261 - Draft: 2017-12-15
The roller brush helps to pick up dirt deep in the carpet or stuck to the floor. If the roller brush is no longer rotating, you may have to remove it and clean or replace it. Follow these steps to remove the roller brush.
TOOLS:
Phillips #2 Screwdriver (1) Metal Spudger (1)
This document was generated on 2020-11-28 06:02:06 AM (MST).
© iFixit -- CC BY-NC-SA
www.iFixit.com
Page 2 of 7
Shark NV352 Roller Brush Replacement
Step 1 -- Roller Brush
Guide ID: 98261 - Draft: 2017-12-15
Lift the latches on both sides of the vacuum to release the dust canister. Remove the dust canister from the vacuum by lifting it up.
Step 2
Lay down the vacuum to access the bottom panel of the roller brush compartment.
This document was generated on 2020-11-28 06:02:06 AM (MST).
© iFixit -- CC BY-NC-SA
www.iFixit.com
Page 3 of 7
Shark NV352 Roller Brush Replacement
Step 3
Guide ID: 98261 - Draft: 2017-12-15
Using the metal spudger, pry the two small wheels located at the two bottom corners of the vacuum to remove them.
Step 4
Remove the eight 19mm Phillips #2 screws from the plastic cover. Remove the two 14 mm Phillips #2 screws from the upper section of the plastic cover.
This document was generated on 2020-11-28 06:02:06 AM (MST).
© iFixit -- CC BY-NC-SA
www.iFixit.com
Page 4 of 7
Shark NV352 Roller Brush Replacement
Step 5
Guide ID: 98261 - Draft: 2017-12-15
You will need to apply a strong force while pulling the wheels off because they are attached very
tightly.
Remove the wheels by pulling them out of their axles, away from the vacuum.
This document was generated on 2020-11-28 06:02:06 AM (MST).
© iFixit -- CC BY-NC-SA
www.iFixit.com
Page 5 of 7
Shark NV352 Roller Brush Replacement
Step 6
Guide ID: 98261 - Draft: 2017-12-15
Perform the next step slowly and carefully so the wiring connecting the motherboard to the rest of
the vacuum is not broken.
Gently pull the grey lower part of the roller brush compartment away from the purple upper part of the compartment.
Step 7
Lift up and then pull the roller belt off of the roller brush and the motor to remove it.
This document was generated on 2020-11-28 06:02:06 AM (MST).
© iFixit -- CC BY-NC-SA
www.iFixit.com
Page 6 of 7
Shark NV352 Roller Brush Replacement
Step 8
Guide ID: 98261 - Draft: 2017-12-15
Take out the roller brush by lifting it out of its tray.
To reassemble your device, follow these instructions in reverse order.
This document was generated on 2020-11-28 06:02:06 AM (MST).
© iFixit -- CC BY-NC-SA
www.iFixit.com
Page 7 of 7
wkhtmltopdf 0.12.5 Qt 4.8.7