Primo Water Dispenser with Single-Serve Coffee Maker

Features

• Storage Compartment: Removable tray organizes single-serve coffee pods (pods sold separately).
• Convenience Switches: Located on the rear of the dispenser for heating, cooling, and night light power.
• Brewing Controls: Select beverage serving size: 6, 8, or 10 ounces.
• Empty Bottle Light: Flashes red when the water bottle is empty and needs replacement.
• Heating Light: Flashes while water heats; stops flashing when water is fully heated.
• Coffee Pod Drawer: Prepares single-serve coffee pods. Press the silver button to remove the drawer. CAUTION: Keep fingers away from the sharp needle inside the drawer.
• Cold Water Lever: Push glass or container against the lever to dispense. Release to stop water flow.
• Hot Water Lever: Features a child-safety lock. Press the red button, then push glass or container against the lever to dispense. Release to stop water flow.
• Sensor Assembly: Pumps water from the bottle to the hot and cold water reservoirs.
• Sensor Support: Located inside the cabinet door to keep the sensor assembly clean during bottle changes.
• Drip Tray: Removable and dishwasher-safe. Features a red indicator that rises when it's time to empty.
• Water Bottle: Not included. Uses 3 and 5-gallon bottles. Visit PrimoWater.com to find Primo Water nearby.

Safety Warnings and Precautions

Read this guide completely before assembling, installing, and operating the dispenser to reduce the risk of injury and material damage. Failure to follow instructions may cause personal injury or material damage. Models that heat water dispense it at very high temperatures; improper use can cause burns.

• Ensure the dispenser is correctly assembled and installed per this manual before use.
• This dispenser is designed solely for dispensing water. Do not use with other liquids or for other purposes. Use only microbiologically safe, branded bottled water.
• For indoor use only. Keep the dispenser in a dry location away from direct sunlight. Do not use outdoors.
• Install and operate only on a hard, flat, and level surface.
• Do not place the dispenser in an enclosed space or cabinet.
• Do not operate in the presence of explosive vapors.
• Position the rear of the dispenser at least 4 inches from the wall for airflow. Ensure at least 4 inches of clearance on the sides for airflow.
• Plug into a Ground Fault Circuit Interrupter (GFCI) protected receptacle.
• Do not use an extension cord.
• Always pull the plug directly from the outlet; never pull the power cord.
• Do not use the dispenser if the cord is frayed or damaged.
• Do not immerse the cord, plug, or any part of the dispenser in water or other liquids to prevent electric shock.
• Ensure the dispenser is unplugged before cleaning.
• Never allow children to dispense hot water without adequate, direct supervision. Unplug the unit to prevent unsupervised use by children.
• Do not dispense hot water if the water bottle is empty.
• Contact Primo Water at 866-429-7566 for troubleshooting assistance.

Quick Start Guide

1. Place the dispenser on the floor in your desired location. The product is designed for indoor use only. Note: Do not plug the power cord into the wall outlet until instructed.
2. Position the dispenser so its rear is at least 4 inches from the wall, with at least 4 inches of clearance on both sides.
3. Slide the drip tray into place.
4. Slide the coffee pod drawer into the slot until it clicks. CAUTION: Keep fingers away from the inside of the drawer, as the needle is very sharp.
5. Clean the sensor with a damp cloth and dish soap. Visit PrimoWater.com for detailed cleaning instructions. Place the sensor assembly in the support inside the door to keep it clean.
6. Take a Primo water bottle (sold separately) and remove the cap completely. Insert the sensor assembly into the bottle. Press firmly to secure the assembly over the bottle opening. For 3-gallon bottles, squeeze the tabs on the top of the sensor assembly to separate the sensor cap from the collar, then press the collar firmly onto the bottle opening.
7. Slide the bottle into the cabinet and close the door. (Note: Water will not pump from the bottle unless the door is fully closed).
8. Plug the dispenser into a GFCI-protected outlet. The dispenser will begin to pump water to fill the internal hot and cold reservoirs.
9. Turn on desired functions by flipping the switches on the rear of the dispenser to the ON position. (Blue: cools water, Green: night light, Red: heats water).
10. Once the dispenser stops filling the internal reservoirs, dispense and discard approximately 1 quart of water (about 2 pint glasses) from both the hot and cold water spouts.
11. Cold water will be ready in approximately 1 hour, and hot water in approximately 12 minutes.

Operating Instructions

Dispensing Cold Water

1. Water will take approximately 1 hour to cool completely after initial setup.
2. Press your glass or container against the lever below the blue circle to dispense cold water. Release to stop dispensing.

Dispensing Hot Water

1. Water will take approximately 12 minutes to reach its hottest temperature after initial setup. The heating light will stop flashing once the water is fully heated.
2. This dispenser is equipped with a child-safety feature. To dispense hot water, press the red lock button, then press your glass or container against the lever directly below the red lock button. Release to stop dispensing.

Preparing Single-Serve Beverages

1. Press the silver button to eject the coffee pod drawer and remove it completely from the dispenser.
2. Insert your chosen K-Cup pod (sold separately) and press it firmly into place until the needle pierces the bottom of the pod and the top of the pod is level with the top of the drawer. CAUTION: Keep fingers away from the inside of the drawer, as the needle is very sharp.
3. Slide the drawer into the dispenser and push until it clicks. The quantity buttons will illuminate green.
4. Press the button for your desired quantity: 6 ounces, 8 ounces, or 10 ounces.
5. If you do not select a quantity within 5 seconds, the quantity buttons will turn off to prevent accidental dispensing of hot water. To reactivate the quantity selection buttons, simply remove and re-insert the coffee pod drawer and make your selection.
6. After brewing, eject the drawer by pressing the silver button directly above the drawer opening, carefully remove and discard the used K-Cup pod, and slide the drawer back into the dispenser.
7. You can brew approximately three 6-ounce servings or two 8- to 10-ounce servings consecutively. The red heating light will flash when water is heating.

K-Cup is a registered trademark of Keurig Green Mountain, Inc. Use of the K-Cup trademark does not imply any affiliation or endorsement by Keurig Green Mountain, Inc.

Using the Reusable Coffee Filter

1. Turn the coffee filter lid to the left to remove it.
2. Add your favorite coffee grounds (sold separately) up to the fill line above the filter screen.
3. Replace the coffee filter lid and turn it to the right to secure it.
4. Align the notch on the bottom of the reusable coffee filter with the needle inside the coffee pod drawer.
5. Slide the coffee pod drawer into the dispenser and push until it clicks.

NOTE: Fine ground coffee, tea leaves, cocoa, or other powdered beverages are not recommended as they may clog the filter.

Replacing the Water Bottle

When the bottle is empty, the empty bottle light will flash. To prevent freezing or overheating, the dispenser will not heat or cool water when the bottle light is flashing. Replace the bottle as soon as possible to re-enable heating and cooling.

1. Open the dispenser cabinet door and slide the empty bottle out of the cabinet.
2. Remove the sensor assembly from the empty bottle and place it in the sensor support.
3. Set the empty bottle aside.
4. Completely remove the plastic cap from the new bottle.
5. Place the sensor assembly into the new bottle and slide the collar down until it snaps into place. Press the top of the sensor until the tube touches the bottom of the bottle. For 3-gallon bottles, squeeze the tabs on the top of the sensor assembly to separate the sensor cap from the collar, then press the collar firmly onto the bottle opening.
6. Slide the bottle into the cabinet and close the door.

Cleaning and Maintenance

For best taste, performance, and hygiene, clean the cabinet, controls, bottle sensor, and spout each time you replace the water bottle. Use a clean, soft cloth and a food-grade disinfectant or bleach solution.

Empty and clean the drip tray as needed. Regularly remove and clean the coffee pod drawer (keep fingers away from the needle inside the drawer). The drip tray and coffee pod drawer are dishwasher-safe.

Clean the cold reservoir at least once every 3 months.

Visit PrimoWater.com for detailed cleaning instructions.

Limited Warranty

Primo Water Corporation warrants to the original purchaser that this dispenser will be free from defects in material and workmanship for one (1) year from the date of purchase, provided it is assembled and operated according to the printed instructions. Proof of purchase is required.

The warranty is limited to repair or replacement of parts found defective under normal use and maintenance, as determined at Primo Water's discretion. Contact Primo Water Customer Service before returning any parts. Shipping charges for defective parts must be prepaid by the customer; replacement parts will be shipped prepaid.

This warranty does not cover failures due to accident, abuse, misuse, alteration, improper application, installation, or maintenance/service by the customer or a third party, or failure to perform normal routine maintenance. It also excludes damage to the finish, including scratches, dents, or discoloration.

This limited warranty replaces all other express warranties. Primo Water disclaims all warranties for products purchased from unauthorized sellers. After the one-year express warranty period, Primo Water disclaims all implied warranties, including warranties of merchantability and fitness for a particular purpose. Primo Water shall not be liable for any special, indirect, punitive, incidental, or consequential damages.

For warranty information, additional assistance, or instructional videos, visit PrimoWater.com or call 1-866-429-7566. Primo Water Corporation, 200 Eagles Landing Blvd., Lakeland, FL 33810.