Rev-A-Shelf Vanity/Base Cabinet Filler Installation Instructions

Model: BLUM 432 VANITY SOFT-CLOSE FILLER

Product Overview

This document provides instructions for installing the Rev-A-Shelf Vanity/Base Cabinet Filler. The unit is designed to be installed in new cabinet construction.

Estimated Assembly Time: 20 MIN

Care and Maintenance: Clean with a damp cloth and wipe parts dry.

For video instructions, visit: rev-a-shelf.com/videos

Tools Required

Drill (with 3/16" bit)
Screwdriver (#2 Phillips)
Measuring Tape
Hammer
Pencil

Installation Steps

Step 1: Measure and Cut Scribe Rails

Measure the scribe rail thickness and length according to your specific cabinetry. Cut four rails in total: two for the sides, and one each for the top and bottom. The recommended scribe rail height is 3/4".

Note: Do not remove the front shipping strap prior to installation.

Step 2: Install Scribe Rails

Install the upper and lower scribe rails to the filler pullouts. Be careful not to split the wood. If using screws, pre-drill holes first. Align the scribe rails with the front edge of the filler pullouts. Align the top scribe rail with the top of the base cabinet lower mounting.

Note: For frameless applications, use a 1/16" thick scribe rail to properly space the filler unit.

Step 3: Mount Filler Pullout

Pre-drill holes using a 3/16" drill bit. Refer to the table below for specific measurements based on filler height.

Filler Size (Height)	Measurement #1 (From Top of Cabinet, Down)	Measurement #2 (From Top of Cabinet, Down)
26" Filler	3/8"	23-7/8"
30" Filler	3/8"	27-7/8"

Mount the filler cabinet pullout to the adjacent cabinets. Ensure the filler is flush with the top of the cabinet wall and behind the face-frame, if applicable. Repeat for the remaining adjacent cabinet.

Step 4: Attach Onlays or Door Panels

Remove the front shipping strap. Attach any onlays or door panels (not provided) as shown in Figure 5.

Note: Metal brackets cannot be pre-drilled or screwed into.

Step 5: Disassemble Pullout from Chassis (If Necessary)

The pullout unit does not need to be removed for installation. However, if removal is necessary, locate the release levers for the Blum Tandem slides as shown in Figures 6a-b. Squeeze the release triggers and hold while pulling the filler away from the cabinet run.

Step 6: Adjust Front Slide Height

Press up on the adjustment tab. Push toward the back of the unit. The maximum rise of the filler is 1/8". (See Figures 7a-c).

	Rev-A-Shelf 6" 432 Wall Filler: Specifications and Dimensions Detailed technical specifications, dimensions, and model information for the Rev-A-Shelf 6" 432 Wall Filler, including part numbers, lengths, and weight ratings.
	Rev-A-Shelf Soft-Close Tip-Out Trays Installation Instructions Step-by-step guide for installing Rev-A-Shelf's soft-close tip-out trays in sink base cabinets. Includes tools required, parts list, and detailed instructions for preparing panels, mounting hinges, and attaching trays.
	Rev-A-Shelf Tip-Out Tray System Installation Instructions Comprehensive installation guide for the Rev-A-Shelf Tip-Out Tray System, covering hinge types, tray assembly, and mounting for polymer and slim series trays. Includes tools required, helpful hints, and customer support contact.
	Rev-A-Shelf Tiered Drawer System Installation Guide Step-by-step installation instructions for the Rev-A-Shelf Tiered Drawer System, including parts list, tools required, and maintenance tips. Model I-4WTCD-0725.
	Rev-A-Shelf 53WC Double Waste Container Specifications and Dimensions Comprehensive specifications and dimensional data for the Rev-A-Shelf 53WC Double Waste Container, featuring two 50-quart polypropylene bins, full-extension undermount slides, and soft-close functionality.
	Rev-A-Shelf Heavy-Duty Mixer Lift Installation Instructions Detailed installation guide for the Rev-A-Shelf Heavy-Duty Mixer Lift, including tools required, parts list, preparation steps, and adjustment instructions for optimal performance.
	Rev-A-Shelf Door-Mount Kit Installation Instructions Comprehensive guide for installing the Rev-A-Shelf Door-Mount Kit, detailing parts, tools, and step-by-step assembly for cabinet doors.
	Rev-A-Shelf Craftsman Collection Deep Drawer Divider Insert Installation Guide Step-by-step installation instructions and parts list for the Rev-A-Shelf Craftsman Collection Deep Drawer Divider Insert. Includes care and maintenance tips.