VEVOR

Introduction

This document provides the original instructions for the VEVOR Fishing Rod Holders. Please read all manual instructions carefully before operating.

VEVOR reserves the right to interpret its user manual. The appearance of the product is subject to the item received. VEVOR apologizes if updates to technology or software on the product are not communicated in advance.

Important Warnings

[Warning Icon] To reduce the risk of injury, user must read instructions manual carefully.

WARNING

1. Risk of suffocation! Keep all packaging materials away from children and pets. These materials are a potential source of danger, e.g., suffocation.
2. Read these instructions carefully and retain them for future use. If this product is passed to a third party, these instructions must be included.

Installation Steps

When you receive the fishing rod holder, please sort the accessories first and check the quantity of each accessory as shown in the figures below.

Diagram Description: An illustration shows the assembled VEVOR Fishing Rod Holders, a multi-tiered rack with wheels, designed for organizing fishing rods.

Part List

The following components are included in the package:

• Part 1: Top plate (1 piece)
• Part 2: Lower frame (1 piece)
• Part 3: Support plate (2 pieces)
• Part 4: Upper frame 1 (1 piece)
• Part 5: Lower frame 1 (1 piece)
• Part 6: Upper frame 2 (1 piece)
• Part 7: Lower frame 2 (1 piece)
• Part 8: Upper frame 3 (1 piece)
• Part 9: Foot down (2 pieces)
• Part 10: Hanger (4 pieces)
• Part 11: Hook (2 pieces)
• Part 12: Layer board (1 piece)
• Part 13: Wheels (with brakes) (4 pieces)
• Part 14: Wheels (2 pieces)
• Part 15: Storage bag (1 piece)
• Accessory A: Screw M6*12 (14 pieces)
• Accessory B: Screw M6*25 (16 pieces)
• Accessory C: Hex wrench (1 piece)
• Accessory D: Open end wrench (1 piece)

Diagram Description: An exploded view diagram shows all parts labeled with numbers 1 through 15, and accessories labeled A through D, illustrating their individual components.

Assembly Instructions

Step 1: Frame Assembly

Assemble part 4 and part 5. Assemble part 6 and part 7. Assemble part 8 and part 9.

Diagram Description: Diagrams show the assembly of vertical frame components. Part 4 is joined with part 5. Part 6 is joined with part 7. Part 8 is joined with part 9.

Step 2: Securing Frames

After assembling the frames in Step 1, tighten them using 6 screws of type A.

Diagram Description: Diagram shows screws (labeled 'Ax6') being used to secure the assembled frame sections from Step 1.

Step 3: Attaching Shelves

Assemble part 1 (Top plate), part 2 (Lower frame), and part 12 (Layer board) together with part 4 and part 8. Use 12 screws of type B.

Diagram Description: Diagram illustrates attaching the top plate (1), lower frame (2), and layer board (12) to the main vertical frame structures (4 and 8) using 12 screws (labeled 'Bx12').

Step 4: Attaching Support Plates

Assemble two parts 3 (Support plates) along with part 4 and part 6. Use 8 screws of type B.

Diagram Description: Diagram shows two support plates (3) being attached to the frame assembly (parts 4 and 6) using 8 screws (labeled 'Bx8').

Step 5: Attaching Hangers

Four parts 10 (Hangers) are fixed using 8 screws of type A.

Diagram Description: Diagram shows four hangers (10) being attached to a frame section using 8 screws (labeled 'Ax8').

Step 6: Inserting Hooks

Insert part 11 (Hooks) into the crossbar of part 4.

Diagram Description: Diagram illustrates inserting two hooks (11) into the designated crossbar on part 4.

Step 7: Attaching Wheels

Install four parts 13 (Wheels with brakes) onto the bottom of part 5 and part 9. Install two parts 14 (Wheels) onto the bottom of part 7.

Diagram Description: Diagram shows wheels (13) being attached to the base of parts 5 and 9, and wheels (14) being attached to the base of part 7.

Step 8: Attaching Storage Bag

Install the storage bag (part 15) onto part 8 and part 9.

Diagram Description: Diagram shows the storage bag (15) being attached to the upper frame sections (8 and 9).

Cleaning and Storage

1. Wipe with a soft, dry cloth. Never use an abrasive cleanser or harsh pad. Ensure the product remains dry.
2. Children are not permitted to wipe the product to prevent tipping and falling injuries.
3. Periodically check screws every few months for looseness and tighten them as needed.

Manufacturer and Importer Information

Manufacturer: Shanghaimuxinmuyeyouxiangongsi

Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.

Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREET EASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

UK Representative: YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX

EU Representative: E-CrossStu GmbH Mainzer Landstr.69, 60329 Frankfurt am Main.