Potensic Atom SE User Manual

1. Disclaimer & Precautions

1.1 Disclaimer

Drones are products with potential dangers and relatively complex operations. Prior to usage, it is crucial to thoroughly read the complete User Manual to grasp basic knowledge and become familiar with the drone's functions. For the initial use of ATOM SE, it is recommended to operate it in GPS mode in a spacious outdoor area to acquaint yourself with its functions.

Strictly adhere to the Manual's operational instructions and precautions to ensure safe and correct usage. Users below the age of 16 should be supervised by an adult, and the product should be kept out of reach of children.

The Company disclaims responsibility and does not provide warranty services for any direct or indirect losses (including property loss and personal injury) resulting from the user's failure to follow the Manual's safety guidelines.

Avoid dismantling any part of the product except for propellers or modifying it without official guidance; users will be accountable for any consequences arising from such violations.

For assistance with usage, operation, and maintenance issues, feel free to contact our local dealer or the Company.

Potensic reserves the final interpretation rights of this document and related product documents, and the information is subject to change without notice. For the latest updates, please visit https://www.potensic.com.

1.2 Safety Precautions

Keep away from obstacles and crowds

To ensure the safety of both the user and those around, please keep the product away from crowded areas, high-rise buildings, and high-voltage cables. Additionally, refrain from using it in severe weather conditions such as strong winds, heavy rain, and thunderstorms. This precaution is necessary as the product may exhibit unpredictable flight speeds, status fluctuations, and potential hazards.

Keep off moisture

To prevent anomalies or damage caused by humidity affecting precise electronic components and mechanical parts inside the product, please ensure it is kept away from moisture.

Safe operation

When operating the drone, the likelihood of unforeseen risks rises when users are fatigued, in poor mental condition, or lack experience. To ensure safety, it is essential to refit or repair the product using original parts. Operate the product strictly within specified limits, and be sure to adhere to local safety regulations.

Keep away from high-speed revolving parts

While the product's propellers are spinning at a high speed, keep it away from crowds and animals to prevent scratches or disturbances. Avoid touching the spinning propellers with your hands.

Keep away from heat source

To prevent anomalies, deformation, and potential damage, keep the product away from heat and high-temperature exposure. This precaution is especially crucial as the product comprises metal, fiber, plastic, and electronic elements.

1.3 Warning & Prompts

• 01. Keep the package and manual in a secure place as they contain important information.
• 02. Users are responsible for ensuring that the use of this drone does not cause harm to the person or property of others.
• 03. Our company and dealers are not liable for losses and personal injuries resulting from improper use or operation.
• 04. Users must strictly follow the steps outlined in the user manual to install and test the drone. During flight, maintain a minimum distance of 1 to 2 meters from users or other individuals to prevent the drone from colliding with human bodies, causing injury.
• 05. The product should be assembled by an adult. Users aged below 16 should not handle the product alone. The battery should be charged under the supervision of an adult and should be kept away from flammable materials during the charging process.
• 06. The product contains small parts. Please place them out of reach of children to prevent accidental ingestion.
• 07. Do not operate the product over roads or standing water to avoid accidents.
• 08. It is forbidden to dismantle or refit the product, except for the propellers, as doing so may lead to malfunctions in the drone.
• 09. Please recharge the intelligent battery with a USB charger that conforms to FCC/CE standards.
• 10. The remote controller has a built-in 3.7V lithium battery which needs no replacement.
• 11. Do not short-circuit or squeeze the battery to avoid explosion.
• 12. Do not place the battery in hot place (in fire or near electric heater).
• 13. Keep a safe distance from the high-speed revolving propellers; avoid using the product in crowds to prevent scratches or injuries.
• 14. Do not use the product in places with strong magnetic field, such as near high-voltage cable, buildings that contain metals, automobiles and trains; otherwise, the connection stability can be compromised.
• 15. Please make sure to thoroughly understand local laws and regulations to avoid any unauthorized use of the drone.
• 16. To comply with the requirements of the aeronautical radio magnetic environment, during the period of radio control orders issued by the relevant national authorities within the specified regions, the use of remote controller should be suspended as instructed.
• 17. Please refrain from flying at low altitudes over water surfaces.
• 18. Please stay away from airports, flight paths, and other restricted areas.

2. Reading Tips

2.1 Legend

• Prohibited ?
• Important ❗
• Operation & use prompts ?
• Technical Terms and reference information ℹ️

2.2 Suggestions of Use

1. It is advisable to watch the tutorial video and Quick Start Guide before referring to the Manual.
2. Be sure to read the Disclaimer & Precautions section first when consulting the Manual.

2.3 Tutorial Video / Download App

Scan the QR code on the right and you can:

1. Download PotensicPro App (hereinafter referred to as "the App").
2. Watch the tutorial videos.
3. Access the latest User Manual.
4. Learn about the frequently asked questions(FAQ)

QR Code: A square black and white pattern used for quick access to digital information.

2.4 Registration & Help

It's required to set up an account when using the App for the first time to have better user experience.

Registration Procedures

1. Enter your email;
2. Set your password;
3. Check and agree with the Protocols;
4. Register.

You can log into the App after registration. Note: An Internet connection is required during the registration.

Help

Thanks for purchasing Potensic Atom SE. Before using the drone for the first time, we recommend that you read the user manual carefully.

Please contact our support team at support@potensic.com if you encounter any problem or issue with the drone. Make sure to submit your order ID and the details of the issue.

3. Overview

3.1 Introduction

This chapter introduces the functional characteristics of Atom SE, as well as the component of the drone and the remote controller.

Atom SE features foldable arms for convenient portability, with a lightweight body weighing less than 250g. The drone possesses a Vision Positioning System, which allows for precise hovering in low-altitude indoor and outdoor environments. Equipped with a GPS sensor, the drone enables positioning and automatic return. The camera utilizes a 1/3-inch Sony CMOS image sensor, capable of capturing high-definition 4K/30FPS video and 12 million pixels photos. Atom SE employs proprietary ShakeVanish™ electronic image stabilization technology for clear and stable footage.

Atom SE's remote controller utilizes the PixSync™ 2.0 2.4G digital transmission technology, achieving a maximum communication distance of up to 4km and 720P video transmission in ideal conditions. The controller features a retractable and foldable design, providing a placement for your mobile device when unfolded. When connected to the controller via a USB cable, you can operate and configure your drone through the App, as well as view high-definition video transmission. The built-in lithium battery in the remote controller has a maximum working time of approximately 2.3 hours.

Atom SE utilizes proprietary SurgeFly™ flight control technology, achieving a maximum flight speed of 16m/s (52ft/s) and a maximum flight time of approximately 31 minutes, with resistance against wind up to Level 5.

Test conditions for max. flight time: Fly at an even speed of 5m/s at 25°C and in breezeless condition.

Test conditions for max. transmission distance: Measured at an open and no-interference environment, with a flight height of 120m, and without considering the return of the drone.

Power consumption will increase considerably when the drone is returning against the wind. If you receive a prompt of encountering strong wind from the App, please make sure to lower the flight altitude and return in time to ensure safety of the drone.

3.2 Drone Diagram

Illustration of the Potensic Atom SE drone with numbered components.

• 1. Charging indicator
• 2. TYPE-C charging port
• 3. Battery buckle
• 4. SD card slot
• 5. Tail indicator
• 6. Monocular visual module
• 7. TOF module
• 8. Bottom cooling hole
• 9. Power indicator
• 10. Power/frequency pairing button
• 11. Integrated single-axis gimbal camera
• 12. Brushless motor
• 13. Propeller
• 14. Arm
• 15. Antenna tripod
• 16. Arm shaft

3.3 Remote Controller Diagram

Illustration of the Potensic Atom SE remote controller with numbered components.

• 1. Power button: Long press for 2s to power on/off.
• 2. Power indicator: Indicate the power level or other status of the remote controller.
• 3. Control stick slot: One slot respectively at the left and right side, used to store the sticks.
• 4. TYPE-C interface: To charge the remote controller/connect mobile device.
• 5. RTH / Pause button: Long press for 1s to return to HOME point automatically; Short press to pause auto flight.
• 6. Control stick
• 7. Foldable double antennas
• 8. Placement for mobile device: To place mobile device.
• 9. Shoot button: Short press it to shoot one picture.
• 10. Record button: Short press to start/stop recording.
• 11. Thumbwheel: Dial the thumbwheel horizontally to control the tilt of the gimbal.

3.4 Preparing the Drone

The product is delivered under folded status. Please unfold it as follows:

1. Unfold the front arm before the rear arm.
2. Unfold the propeller blades.

Illustration showing the unfolding sequence of the drone's arms and propellers.

3.5 Preparing the Remote Controller

Installation of mobile phone and control stick

1. Unfold the antenna.
2. Connect your mobile phone to the USB cable.
3. Insert the part of your mobile phone with the USB cable into the slot of the remote controller.
4. Pull and open the remote control with both hands and fix your mobile phone stably.
5. Connect the other end of the USB cable to the remote controller.
6. Take out the sticks.
7. Screw in both control sticks clockwise.
8. Installation completed.

Illustration showing the setup of a mobile phone on the remote controller and the attachment of control sticks.

3.6 Charging / Startup and Shutdown

Before the first flight, it is essential to wake up the battery; otherwise the drone won't start. Connect the TYPE-C charging port of the battery and a USB charger to the AC power supply to finish a single charging (USB charger is not included in the package. User can use a charger that conforms to FCC/CE specification to charge the battery). The red indicator will stay on during charging, and turn off automatically after charging is done. Users can charge the battery with the Parallel Charging HUB if a Fly More Combo is purchased. For more details, please refer to the Fly More Combo of Parallel Charging HUB. The Parallel Charging HUB can also charge the remote controller.

Illustration showing two charging modes: Mode 1 (single battery charging) and Mode 2 (parallel charging hub).

• The shortest charging period is approx. 1h 25min through the TYPE-C charging port. Make sure your charger supports 5V/3A output in order to achieve this charging speed.
• User is suggested to charge the battery through the Parallel Charging HUB, in order to charge 3 batteries quickly at the same time.
• It is suggested to remove the battery from the drone to charge for safety reasons; otherwise, the drone won't power on if the battery is being charged in the drone.
• If the charging cable is connected while the drone is on, it will power off automatically and the charging will continue.
• The battery may become too hot after use; do not charge it until it cools down; otherwise, charging can be rejected by the smart battery.
• Charge the battery every three months to sustain the cell's activity.
• Please connect the original cable or any cable that supports over 3A current to the TYPE-C port; otherwise, it may cause charging failure or battery damage.

Startup

• Drone: Make sure the battery is inserted in the battery bin, short press and then long press the power button until all indicators are on, and then release the button to start up.
• Remote controller: Long press the power button until all indicators are on, and then release the button to finish startup.

Shutdown

• Drone: Short press and then long press the power button of the drone until all indicators are off, and then release the button to shut down.
• Remote controller: Long press the power button until all indicators are off, and then release the button to shut down.

4. Drone

ATOM SE consists of a flight control system, a communication system, a positioning system, a power system and a smart flight battery. This chapter sets down the functions of all parts of the drone.

4.1 Positioning

Atom SE adopts Potensic's new SurgeFly™ flight control technology, which supports the following two positioning modes:

• GPS positioning: Provide precise positioning and navigation to the drone; support precise hovering, smart flight and auto return.
• Vision positioning: It can realize high-precision positioning at a low altitude based on the Downward Vision System. The visual positioning can be realized without a GPS signal, so that the product can be used indoors.

How to switch:

The flight control system will switch automatically according to the environment of the drone. If both the GPS and lower visual system fail, the flight control will be switched to attitude mode, under which, the drone fails to realize stable hovering and the user needs to correct the flight gesture manually through the control stick.

The difficulty of drone handling will be increased greatly in Attitude Mode; make sure to master the behaviors and operation of the drone in this mode prior to use; avoid flying the drone over a long distance to avoid risks due to failed judgment of drone behaviors.

• In Vision Positioning (OPTI Mode), the Intelligent Flight Modes are not available, and the flight mode will be limited to Video Mode.
• The difficulty of controlling the drone will increase dramatically in ATTI Mode so make sure to master the operation of the drone in this mode. Always keep the drone within sight in order to avoid risks in case of failed judgment of the drone's attitude and direction.

4.2 Downward Vision System

The Atom SE is equipped with a downward vision system, it is located beneath the drone. The Downward Vision System consists of a monocular camera and a TOF module. The TOF module includes a transmitter tube and a receiver tube, it can precisely calculate the fly height above the ground by calculating the infrared signals transmission and receiving time. In combination with the monocular camera, the system can help achieve high-precision positioning at low altitudes.

Diagram showing the TOF Module and Monocular Camera components of the Downward Vision System.

Detection Fields

The Downward Vision System works best when the drone is at an altitude of 0.3 to 5 m, and its operating range is 0.3 to 10 m.

When GPS is unavailable, the Downward Vision System is enabled if the surface has a discernable surface and sufficient light. The Downward Vision System works best when the drone is at an altitude of 0.3 to 5 m. When the altitude exceeds 5 m, the drone will enter ATTI Mode. Please fly with caution.

How to use

The Downward Vision System has enabled automatically if the positioning conditions are satisfied. The drone tail indicator blinks cyan twice, which indicates the Downward Vision System is working.

Speed limit: To ensure positioning accuracy and flight safety during visual positioning flight, the drone will actively limit its flight speed.

• In OPTI Mode, the maximum flight altitude is 5 m.
• Vision positioning is only an auxiliary flight function. Please always pay attention to changes in the flight environment and positioning mode, and do not rely too much on the automatic judgment of the drone. Users need to control the remote controller at all times and be prepared to operate the drone manually at any moment.
• The Vision System cannot work properly in any of the following situations:
  1. Pure-color surface.
  2. Surface with strong reflection, such as smooth metal surfaces.
  3. Transparent object surface, such as water surface and glass.
  4. The moving texture, such as running pets and moving vehicles.
  5. Scenarios with drastic change of light; For example, the drone flies to outdoor space with strong light from indoor space.
  6. Places with weak or strong light.
  7. The surface with highly repetitive texture, such as floor tile with the same texture and small size, and highly consistent strip pattern.
• For the sake of safety, please check the camera and TOF transceiver tube before the flight, and clean it with a soft cloth if there is any dirt, dust, or water on it;
• Contact Potensic Support if there is any damage to the Vision System.

4.3 Drone Status Indicator

4.4 Smart Battery

4.4.1 Function

Atom SE's smart battery is equipped with high-energy cells and utilizes an advanced battery management system. Detailed information is as follows:

Basic Parameters

Function

• If the battery is not used for a long time, it needs to be charged every three months to ensure its health.
• Please store the battery in a cool and dry place where children cannot reach.

4.4.2 Battery Installation & Removal

Installation:

Insert the battery in the battery compartment and secure the buckle. You will hear a clicking sound when the battery is fully engaged.

Removal:

Press the battery buckle and detach the battery from the battery compartment to remove it.

After inserting the battery, please ensure that the battery buckle snaps back into place. This is crucial for flight safety.

Illustration showing how to ensure the battery buckle is in the safe position.

4.4.3 Charging

See 3.6 for charging method

4.4.4 View Power Level

Once the battery is inserted in the drone, short press the power button to view the power level of smart battery, as shown in the picture below:

Illustration showing the Power Button and LED indicators on the drone battery, and a table detailing power levels based on LED status.

☀️ Indicator is on | ? Indicator is flashing | ⚪ Indicator is off

4.4.5 Operation Instructions of Smart Battery at High/Low Temperature

When the battery temperature is <5°C, the App will prompt a low temperature warning of the battery, and the battery needs to be preheated before flying. When the battery temperature is >60°C, the App will prompt a high temperature warning of the battery, and the drone will not be able to fly.

• The discharge capacity will be weakened greatly and flight duration will reduce at a low temperature, which is normal.
• Avoid long-term running at a low temperature, otherwise, the battery life can be shortened.

4.5 Propellers

There are two types of Atom SE propellers, which are designed to spin in different directions. Marks are used to indicate which propellers should be attached to which motors, the two blades attached to one motor are the same.

• Use the screwdriver from the package to mount the propellers.
• When replacing the propeller blades, it is easier to handle by gripping the motor with your hand.

Make sure you attach the marked propellers to the motors of the arm with marks and the unmarked propellers to the motors of the arm without marks. Otherwise the drone will be unable to fly.

• If a propeller is broken, remove the two propellers and screws on the corresponding motor and discard them. Use two propellers from the same package. DO NOT mix with propellers in other packages.
• Propeller blades are sharp. Handle with care. DO NOT squeeze or bend the propellers during transportation or storage.
• Purchase the propellers separately if necessary.
• Stay away from the rotating propellers and motors to avoid injuries.
• Please check the propeller blades immediately if there are any jitters or speed loss in flight, and timely replace the propellers if it's damaged or deformed.
• Make sure the motors are mounted securely and rotating smoothly. Land the drone immediately if a motor is stuck and unable to rotate freely. Stop flying the drone and contact support if there is any abnormal sound with the motor.
• Make sure that the propellers are installed securely before each flight. Check to make sure the screws on the propellers are tightened.
• When mount or remove the propellers, do not put the screwdriver or other foreign materials inside the motors, otherwise the motor may be damaged.

4.6 Flight Data

ATOM SE will record automatically the flight data and you can access it in the App. Flight record displays the basic data for each flight. Flight log records the detailed data of each flight. If you encounter any issue during the flight, you can report it in the App and upload the flight log if necessary to seek for assistance.

All flight data is stored on your mobile device, and the company will not obtain any of your flight data unless you voluntarily upload it to the cloud seeking for assistance.

4.7 Single Axis Gimbal Camera

4.7.1 Single Axis Gimbal

The Atom SE camera is mounted with a single-axis gimbal, to adjust pitch angle freely from +20° to -90° (horizontal direction is 0°). The angle of the gimbal can be adjusted by dialing the left thumbwheel of the remote controller.

Illustration showing the gimbal's tilt angle range from +20° to -90°.

• The gimbal will be recovered to -9° automatically after each startup.
• Avoid collision and moving the lens by force as the gimbal contains precision elements.
• Ensure that the gimbal is free from foreign matter, and the lens is clean before takeoff.
• The gimbal is connected to the drone through elastic and shock absorption support, to eliminate camera vibration. Do not pull the gimbal by force. For any damage of shock absorption support, please contact the customer service for help.
• Do not bind or paste any object on the gimbal. Otherwise, it may damage the drone.

4.7.2 Camera

Basic Parameters

• Do not touch the lens after recording for a long period of time to avoid scald.
• Do not record video when the drone is not flying; otherwise the drone will trigger overheat protection.
• The sensor will crop out the edges at 1080P/60fps, it's simply capturing a central section of what the full-frame sensor would capture, and FOV is about 66°.

4.7.3 Image Storage

Videos and pictures recorded by ATOM SE will be stored on the SD card instead of the App or your phone gallery. Make sure to insert the SD card prior to flight. Otherwise, it's unable for ATOM SE to record videos or capture pictures. (SD card is not included in the pack list.) User can preview and download the videos and pictures (the drone and the remote controller should be connected) in App.

SD Card Requirements

• File format: FAT32, exFAT
• Capacity: 4G-256G
• Speed requirements: It is suggested to use SD card above U1 (UHS Speed Class 1) or C10 (Class 10)

• The video downloaded from App is just 720P resolution used in video transmission. Please read SD card with computer or other device in order to acquire videos of higher definition.
• The recording can be terminated due to slow write-in when using the U1/C10 SD cards of certain brands.
• If important data is stored on your SD card, please backup them properly.
• Do not insert or unplug the SD card when the product is powered on. It may lead to data damage or loss, or even SD card damage when inserting or unplugging SD card during video recording.
• Potensic does not bear responsibility for any loss due to user's misoperation of SD card.

5. Remote Controller

5.1 Overview

Potensic Atom SE is equipped with the DSRC02A Remote controller, which boasts Potensic long-range PixSync™ 2.0 video transmission technology, offering a maximum transmission range of 4km/13,123ft and 720p when displaying video from the drone to PotensicPro on your mobile device. Easily control the drone and camera using the onboard buttons. The detachable control sticks make the remote controller easier to store. Thanks to the 2.4Ghz dual band antenna, in a wide-open area with no electromagnetic interference, PixSync™ 2.0 smoothly transmits video feed at up to 720p at a max altitude of 120m.

The built-in battery has a capacity of 3000mAh and a maximum run time of 2.3 hours. There is a TYPE-C port for device connection. The remote controller charges the mobile device with a charging ability of 5V/500mA.

• When used with different drone hardware configurations, the remote controller will automatically select the corresponding firmware version for updating and support the following transmission technologies enabled by the hardware performance of the connected drone models:
  1. Atom SE: PixSync™ 2.0
  2. Atom: PixSync™ 3.0

5.2 Control Stick Mode

Mode 1 (Left Hand Throttle)

Diagram illustrating control stick movements for Mode 1 (Left Hand Throttle): Left stick controls Up/Down (throttle), Right stick controls Forward/Backward (pitch) and Left/Right (roll/yaw).

Mode 2 (Right Hand Throttle)

Diagram illustrating control stick movements for Mode 2 (Right Hand Throttle): Left stick controls Forward/Backward (pitch) and Left/Right (roll/yaw), Right stick controls Up/Down (throttle).

5.3 Function

5.3.1 Function List

5.3.2 Indicator

As shown in the picture below, the remote controller is fitted with 4 white LED indicators to indicate the power level and other status.

Illustration of the remote controller with LED indicators labeled 1-4, and symbols for indicator status.

Charging indication

Power indication (in use)

Status indication

5.3.3 Remote Controller Function

Atom SE drone and the remote controller can be used immediately after startup since they have passed frequency pairing before delivery. If a new remote controller or drone is used for the first time, user must conduct frequency pairing for them as follows prior to use:

1. Power on the remote controller and connect it with the mobile phone, launch PotensicPro App, tap Settings and select "Re-pair the drone” to enter the frequency pairing interface.
2. Power on the drone and long press the power button till the drone status indicators flash green, the drone is ready to pairing.
3. Wait for about 7s, the remote controller beeps once to indicate frequency pairing is successful and the flight interface of the App will show realtime video transmission.

• Make sure the remote controller is within 1m of the drone during frequency pairing, and there is no 2.4G frequency interference.
• If frequency pairing fails, check if there are interferences nearby, or other drones are also in frequency pairing mode, or the remote controller is too far away or blocked. Eliminate the problems above and try again.
• Do not relocate or operate the remote controller and the drone during frequency pairing.

5.4 Antenna Angle

Adjust the antenna angle along with the changes of drone altitude and distance, to ensure the best communication status of the remote controller.

Illustration showing optimal antenna angles for close distance (wider angle) and long distance (pointing towards drone).

When the drone is directly above the remote controller, the transmission signal is significantly weakened due to the poor antenna angle. To address this, please lower the flight altitude or fly the drone horizontally for some distance, ensuring that the antenna points towards the drone as much as possible, as shown in the picture.

Illustration showing the drone directly overhead causing weakened signal due to poor antenna angle.

Do not cross the antenna in any case.

Do not press the antenna on your mobile device in any case.

5.5 Remote Controller Calibration

5.5.1 When to perform remote controller calibration

1. When the drone drifts automatically in one direction without any toggling of the control sticks.
2. When the drone automatically and continuously rotates in one direction.
3. When the control sticks are over-sensitive or lack sensitivity.

5.5.2 Calibration Procedure

1. Turn on the remote controller, and connect the mobile device, tap Settings in App, select "Remote Controller Calibration".
2. Make sure the control sticks are in the middle position and do not operate it before tapping to start the calibration.
3. Tap "Start Calibration”, then follow the on-screen instructions and toggle the sticks in all directions until the App displays 100%, and rotate the dial back and forth to its maximum extent.
4. When App prompts “Calibration Succeeded”, the remote controller calibration is completed.

Screenshots of the Remote Controller Calibration interface in the PotensicPro App, showing instructions and progress.

6. PotensicPro App

6.1 App Homepage

Screenshot of the PotensicPro App homepage, with annotations pointing to key features like flight logs, model selection, connection status, and flight interface entry.

• Tap to view the flight logs and Potensic Academy
• Tap to choose the corresponding model. The drone model will be matched automatically if user has connected the remote controller to the mobile phone
• Display connection status
• Tap to enter the flight interface
• Me: Report a problem, modify account info, browse User Agreement, find the missing drone, close account and other settings
• Photo album in App (Connect the drone to see the contents in the drone SD card)
• Homepage of App

6.2 Flight Interface

Screenshot of the PotensicPro App flight interface, with numbered elements indicating various controls and information displays.

1. Return button: Tap to return to the homepage.
2. Navigation prompt bar: Display drone status and flight mode.
3. Flight mode: Video, Normal, Sport.
4. Positioning mode: GPS positioning, OPTI Vision positioning, Atti Attitude mode, no positioning.
5. GPS status: Display GPS signal status and quantity of satellites connected.
6. Signal quality of video transmission: Display the strength of video transmission connection signal between the drone and the remote controller.
7. Power level of the smart battery: Displays battery level and Estimated Remaining Flight Time.
8. Settings: Tap to view information about Safety, Calibration, Control, Camera and About.
   • Safety: Switch on or off Beginner Mode (confines flight to a 30m radius/height, Video Mode only). Set measurement system (Metric/Imperial) and speed (Video/Normal/Sport). Set minimum return altitude and virtual fence. Enable/disable Flight Safety Tips. Battery information: check temperature, current, voltage, etc.
   • Calibration: Includes compass calibration, remote controller calibration, and drone re-pairing.
   • Control: Remote Controller Settings: Tap to switch control stick mode (Mode 1: Left Hand Throttle; Mode 2: Right Hand Throttle).
   • Camera: General Settings: Tap to set white balance, gridlines, segmental recording, etc. Tap to check Micro-SD card capacity and format.
   • Other Settings: Enable/disable Telemetry Data.
   • About: View device information, firmware information, App version, etc.

7. Flight

This chapter introduces safe flight practices and requirements.

7.1 Requirements of Flight Environment

1. Do not use the product in severe weather, such as gale, rain, snow and fog.
2. Only fly in open areas. Tall structures and large metal structures may affect the accuracy of the onboard compass and GPS system and result in positioning failure. It is recommended to keep the drone at least 5m away from structures.
3. Control the product within your sight and keep away from the obstacles and crowds.
4. Do not use the product in places with high-voltage power lines, telecommunication base station or launching tower, to avoid interference of the remote controller.
5. Please use the product with caution when altitude is over 3,000m for the flight performance can be affected when the performance of drone battery and power system is weakened due to environment factor.

7.2 Precautions of Flight

1. Check if the remote controller, intelligent flight battery and mobile device are fully recharged.
2. Check if the drone is intact and propellers are installed correctly.
3. Check if the camera is working normally after power-on.
4. Check if App is running normally.
5. Check if SD card is inserted and make sure camera is clean.
6. Make sure the drone takes off on flat and hard surface, instead of sandstone or bush; the drone may fail to be unlocked if it has major vibration.
7. Please be careful when the drone takes off on surface of moving objects, such as running vehicle and ship.
8. GPS positioning and waypoint flight will be disabled in the south and north polar.
9. Do not use the product in extreme cold or hot place to avoid hazards.

7.3 Connection

Please follow the steps below:

1. Please finish the steps in "3.5 Preparing the Remote Controller" and turn on the remote control.
2. Please finish the steps in “3.4 Preparing the drone” and turn on the remote control.
3. Launch App to view the connection status. Connection is finished when it shows ✅.
4. Tap Enter Device > to enter the flight interface.

It is advised to tap and follow the animated guide to operate for first-time users.

7.4 Flight Mode

Atom SE has three flight modes-Video/Normal/Sport, which can be switched via the App.

Video Mode

Ascent speed: 2m/s, descent speed: 1.5m/s, flight speed: 6m/s

The drone enters Beginner Mode by default when being used for the first time. The flight speed will be limited to the same as in Video Mode to allow you to familiarize yourself with the controls of the drone.

Normal Mode

Ascent speed: 4m/s, descent speed: 3m/s, flight speed: 10m/s

You can exit Beginner Mode after you have mastered adequate flight skills, and the drone will switch to Normal Mode by default.

Sport Mode

Ascent speed: 5m/s, descent speed: 4m/s, flight speed: 16m/s

Video mode is recommended in aerial photography. Sport mode is recommended if you would like to get a speedy flight experience. Please pay more attention in Sport Mode flights as the the responsiveness of the drone significantly increases in Sport mode.

• To ensure flight safety, the Sport Mode is only available when the battery level is greater than 30% and the flight altitude greater than 8m. During the flight in Sport Mode, if the battery level drops below 30% or the flight altitude is lower than 4m, the drone will exit Sport Mode automatically.
• The maximum speed and braking distance of the drone significantly increase in Sport Mode. A minimum braking distance of 30 m (100 ft) is required in windless conditions to ensure safety.

7.5 Compass Calibration

7.5.1 Scenarios Requiring Compass Calibration

1. Compass calibration is required for first-time use.
2. Flying the drone at a location more than 50 km (31 miles) away from its last flight.

• DO NOT calibrate the compass in locations where magnetic interference may occur such as close to magnetite deposits or large metallic structures such as metal mines, steel reinforced basements, bridges, cars, or scaffolding.
• DO NOT carry objects that contain ferromagnetic materials such as mobile phones near the drone during calibration.
• Make sure the drone is at least 1.5m (4.92ft) above the ground during the calibration.
• It is not necessary to calibrate the compass when flying indoors.

7.5.2 Calibration Procedure

Choose an open area to carry out the following procedure.

1. When calibration is required, the App will pop up the calibration interface automatically, just tap "Start calibration”, and the tail indicator will alternatively flash in red and green.
2. Hold the drone horizontally and rotate it 360° till the app shows vertical calibration, and the tail indicator will alternatively flash blue and green.
3. Hold the drone vertically and rotate it 360° around a vertical axis till the App prompts the calibration completed.

You can also trigger compass calibration manually in the App: Settings-Calibration-Compass Calibration.

Illustrations showing the compass calibration process: horizontal and vertical rotation of the drone.

• When you get the prompt "Calibration failed" in the App repeatedly, change the location and try the calibration procedure again.
• Do not calibrate compass while arms are folded.

7.6 Beginner Mode

The drone is automatically set to Beginner Mode for first-time use. In Beginner Mode:

1. The flight distance and height will be restricted at 0~30m
2. The speed level will be restricted to the same as in Video mode
3. Users operating the drone for the first time are suggested to learn and master the drone in Beginner Mode

7.7 Takeoff/Landing/Hovering

7.7.1 Manual Takeoff/Landing

Takeoff

Step 1: Start the motors

Use a combination stick command to start the motors. Push both sticks to the bottom inner or outer corner depending on your control stick mode to start the motors. Release both sticks simultaneously once the motors are spinning.

Illustration showing stick combination commands for starting motors.

Step 2: Push throttle control stick to take off

Push the throttle control stick upwards gently as shown in the picture, release the control stick when the drone leaves ground and it will keep hovering.

Illustration showing gentle upward push of the throttle control stick for takeoff.

Landing

Pull the throttle control stick until the drone lands on ground. Release the throttle control stick when the motors are no longer spinning.

• Take off from stable and level surface, do not take off from or land on the palm or by hand.
• It is not suggested to take off at low battery, for it may affect the battery service life. Please handle it with caution and undertake the corresponding consequences if forced takeoff is required.
• When the drone is not in a level and stationary condition, stay at least 5 m away from the drone, and push both sticks to the bottom inner corner for 2 seconds to forcibly unlock the motors.
• Keep the distance over 0.5m between the drone and ground, for it may fail to enter good hovering status due to air flow when it is close to the ground.
• If the drone fails to be locked after landing due to anomaly, pull down the throttle control stick to the limit position for 3s and the drone will be locked by force.

7.7.2 One-key Takeoff / Landing

One-key takeoff

Tap one-key takeoff button ⬆️ in App, then swipe right in the pop-up window to start the drone automatically then ascend to the height of 1.2m and maintain hovering.

Screenshot of the PotensicPro App showing the 'Swipe right to take off' prompt.

One-key landing

Tap one-key landing button ⬇️ in App, then swipe left in the pop-up window to land the drone, or swipe right to start returning.

Screenshot of the PotensicPro App showing landing options: 'Land' and 'Return'.

7.8 Smart Flight

7.8.1 Circle Flight

• When circle flight is enabled, the drone will ascend to 5m automatically if its height is less than 5m.
• Make sure there's no obstacle in the radius of circle flight and use the drone with caution as the drone does not support obstacle avoidance.

7.8.2 Follow Me Flight

• When follow me flight is enabled, the drone will ascend to 5m automatically if its height is less than 5m.
• The follow accuracy depends on the quality of the drone GPS signal and positioning accuracy of your mobile device.
• The follow me flight depends on the positioning of your mobile device. The App requires positioning permission, otherwise this function cannot be enabled.

7.8.3 Waypoint Flight

• During the waypoint flight, you can adjust the flight altitude by moving the throttle stick.
• During the waypoint flight, once reaches the virtual fence, the drone will exit the waypoint flight and hover in place.

7.9 Return(RTH)

The return consists of three steps, as follows:

1. Ascent: The drone ascends to the preset return altitude (this step is skipped if the drone's altitude is already higher than the return altitude).
2. Level flight: The drone maintains a straight flight at the set altitude towards the HOME point.
3. Landing: Once it reaches the HOME point, the drone will automatically land and stop its motors.

Return to Home (RTH) The drone must be in GPS mode

Diagram illustrating the three steps of Return to Home (RTH): Ascent, Return flight, and Landing.

How to RTH

One key RTH: Press and hold the RTH button on the remote controller for 1s or tap ? in App to pop up the menu, then swipe right to start the return (see 7.7.2).

Auto RTH: When either the drone battery level is low, the signal between the drone and the remote controller is lost or the drone is experiencing other abnormalities, Auto RTH will be triggered.

How to exit the RTH

Method 1: Tap ❌ on the left of App to exit RTH.

Method 2: Briefly press the return button on the remote controller to exit RTH.

RTH Requirements

The drone must take off in GPS mode and successfully record the HOME point.

If the drone takes off in OPTI mode and switches to GPS mode mid-flight, it will not be able to return to the takeoff point.

Please pay attention to the location of the HOME point on the map and the prompts in PotensicPro App.

• To ensure the safety of return flight, please set the appropriate return altitude in the app according to the flight environment.
• During the return course, users can still adjust the flight altitude by toggling the throttle control stick.
• When the drone is within 20 m of the HOME point and RTH is initiated, a pop-up window will appear in the App for the user to select between landing and return. If return is selected, the minimum return altitude is 5 m. The drone will land automatically if no action is taken after a countdown of 10 seconds. Please pay attention to flight safety.
• Tall buildings or obstacles can block the transmission signal and cause signal loss. Do not fly behind buildings beyond the return height, otherwise the drone will collide with obstacles and crash during the return. If the drone enters ATTI mode due to GPS failure or GPS signal interference, it will not be able to return. During the return process, strong headwinds may be encountered. Lowering the flight altitude appropriately can help reduce power consumption. If the power is insufficient, the drone will perform a forced landing in place. Please pay attention to the prompts in PotensicPro App. Do not initiate the return when there are obstacles overhead, such as tall trees, otherwise the drone may crash during the climb.
• Please pay attention to return safety, because the drone does not support obstacle avoidance and may crash when colliding with obstacles during the return course.
• For any GPS signal anomaly in communication loss return, the drone will maintain hovering at ATTI mode, until GPS signal is strong enough and the return will resume.

7.10 Emergency Stop

See 5.3.1 Emergency stop for the detailed operation method.

• Emergency stop function is designed for preventing injuring pedestrians or damaging the valuables by propeller blades in case of drone failure. Please use it with caution, because stopping the motors mid-flight will cause the drone to crash.

8. Appendix

8.1 Specification & Parameters

Drone

Downward Vision System

Camera

Remote Controller

Smart Flight Battery

8.2 Post-Flight Checklist

• Make sure to perform a visual inspection so that the drone, remote controller, camera, flight batteries, and propellers are in good condition. Contact Potensic support if any damage is noticed.
• Make sure that the camera lens and vision system sensors are clean.
• Make sure to store the drone correctly before transporting it.

8.3 Maintenance Instructions

To avoid serious injury to children and animals, observe the following rule:

1. Small parts, such as cables and straps, are dangerous if swallowed. Keep all parts out of reach of children and animals.
2. Store the Smart Flight Battery and remote controller in a cool, dry place away from direct sunlight to ensure the built-in LiPo battery does NOT overheat. Recommended storage temperature: between 22°C and 28°C (71°F and 82°F) for storage periods of more than three months. Never store in environments outside the temperature range of -10°C to 45°C (14°F to 113°F).
3. DO NOT allow the camera to come into contact with or become immersed in water or other liquids. If it gets wet, wipe dry with a soft, absorbent cloth. Turning on a drone that has fallen in water may cause permanent component damage. DO NOT use substances containing alcohol, benzene, thinners, or other flammable substances to clean or maintain the camera. DO NOT store the camera in humid or dusty areas.
4. Check every drone part after any crash or serious impact. If there are any problems or questions, contact Potensic support.
5. Regularly check the Battery Level Indicators to see the current battery level and overall battery life. The battery is rated for 250 cycles. It is not recommended to continue use afterward.
6. Make sure to transport the drone with the arms folded when powered off.
7. Make sure to transport the remote controller with antennas folded when powered off.
8. The battery will enter sleep mode after long-term storage. Charge the battery to exit from sleep mode.
9. Store the drone, remote controller, battery, and charger in a dry environment.
10. Remove the battery before servicing the drone (e.g., cleaning or attaching and detaching the propellers). Make sure that the drone and the propellers are clean by removing any dirt or dust with a soft cloth. Do not clean the drone with a wet cloth or use a cleanser that contains alcohol. Liquids can penetrate the drone housing, which can cause a short circuit and destroy the electronics.
11. Make sure to turn off the battery to replace or to check the propellers.

8.4 Troubleshooting Procedures

1. Why can the battery not be used before the first flight?
   The battery must be activated by charging before using it for the first time.
2. No function
   Check if the Smart Flight battery and the remote controller are activated by charging. If the problem persists, contact Potensic support.
3. Power-on and start-up problems
   Check if the battery has power. If yes, contact Potensic support if it cannot be started normally.

8.5 Risk and Warnings

When the drone detects a risk after powering on, there will be a warning prompt on PotensicPro. Pay attention to the list of situations below.

1. If the drone status is not suitable for takeoff.
2. If the compass experiences interference and needs to be calibrated.
3. Follow the on-screen instructions when prompted.

8.6 Disposal

Observe the local regulations related to electronic devices when disposing of the drone and remote controller.

Battery Disposal

Dispose of the batteries in specific recycling containers only after a complete discharge. DO NOT dispose of the batteries in regular trash containers. Strictly follow the local regulations regarding the disposal and recycling of batteries.

Dispose of a battery immediately if it cannot be powered on after over-discharging.

If the Smart Flight Battery cannot be fully discharged, contact a professional battery disposal/ recycling agency for further assistance.

8.7 C0 Certification

ATOM SE(DSDR04B) is compliant with C0 certification requirements.

MTOM Statement

The MTOM of ATOM SE (Model DSDR04B), including the Smart Flight Battery, Propellers, and a microSD card, is 248 g to comply with C0 requirements.

Users must follow the instructions below to comply with the MTOM requirements for each model:

1. DO NOT add any payload to the drone except the items listed in the List of Items including qualified accessories section.
2. DO NOT use any non-qualified replacement parts, such as smart fight batteries or propellers, etc.
3. DO NOT retrofit the drone.

List of Items, including qualified accessories

For C0

List of Spare and Replacement Parts

For C0

1. ATOM SE Propellers
2. ATOM SE Smart Flight Battery

Remote Controller Warnings

Model: DSRC02A

If the remote controller is disconnected from the drone, the PotensicPro App will prompt an on-screen note, and the drone will perform the preset behavior when the remote controller signal is lost. The remote controller will shut down automatically after 20 minutes of no operation.

• Avoid interference between the remote controller and other wireless equipment. Make sure to turn off the Wi-Fi on nearby mobile devices. Land the drone as soon as possible if there is interference.
• DO NOT operate the drone if lighting conditions are too bright or dark when using a mobile phone to monitor the flight. Users are responsible for correctly adjusting the display brightness when using the monitor in direct sunlight during flight operation.
• Release the control sticks or press the flight pause button if an unexpected operation occurs.

EASA Notice

Make sure to read the Drone Information Notices document included in the package before use. Visit the link below for more EASA notice information on traceability.

https://www.easa.europa.eu/en/document-library/general-publications/drones-information-notices

Original instructions

This manual is provided by Shenzhen Potensic Intelligent Co., Ltd and the content is subject to change.

Address: Room 1901, Jinqizhigu Building, Tangling Road, Nanshan District, Shenzhen, China.

WARNING

The product should only be used by adults and children over 16 years. Adult supervision is required for children under 16 years.

German: Hinweis: Dieses Produkt ist für die Erwachsene und die Kinder ab 16 Jahren. Die Kinder unter 16 Jahren müssen von Erwachsenen beaufsichtigt werden.

French: Avertissement: Ce produit est destiné aux adultes et aux enfants de plus de 16 ans. Les enfants de moins de 16 ans doivent être surveillés par des adultes.

Italian: Avvertimento: Questo prodotto è destinato all'uso per i adulti e bambini di età superiore ai 16 anni. I bambini di età inferiore ai 16 anni devono essere sorvegliati da un adulto.

Spanish: Advertencia: Este producto es para adultos y niños mayores de 16 años. Los niños menores de 16 años deben ser supervisados por adultos.

Japanese: 警告: この製品は、大人と16歳以上の子供には使用対象です。16歳未満の子供は大人の監視が必要です。

DANGER: Only suitable for ages 16+

WARNING: NOT SUITABLE FOR CHILDREN UNDER 3 YEARS DUE TO SMALL PARTS

CHOKING HAZARD-small parts. Not for children under 3 years.

Tested according to international standards

COUNTRY OF ORIGIN: CHINA

Drone FCC ID: 2AYUO-DSDR04B

Remote controller FCC ID: 2AYUO-DSRC02A

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Manufacturer: Shenzhen Potensic Intelligent Co., Ltd

Address: Room 1901, Jinqizhigu Building, Tangling Road, Nanshan District, Shenzhen, China

EC REP: E-CrossStu GmbH. 69 Mainzer Landstrasse, Frankfurt am Main, 60329, Hessen, Germany (E-crossstu@web.de) +49 069332967674

UK REP: YH Consulting Limited. C/O YH Consulting Limited Office 147, Centurion House, London Road, Surrey, TW18 4AX (H2YHUK@gmail.com) +44 07514-677868

✅ UK ✅ CA MADE IN CHINA