Parts List
Check that you have all the below parts for this model before assembling the playard.
- Item #: 1 Playard (fully assemble)
- Item #: 1 Mattress
- Item #: 1 Bassinet
- Item #: 4 Metal Support Tubes (2 male, 2 female)
- Item #: 1 Changing table
- Item #: 2 Long Curved Bar
- Item #: 2 Short Bar with Connector Knob
- Item #: 1 Travel / Storage Bag
- Item #: 1 Diaper Stacker
- Item #: 1 Mobile Lower Arm
- Item #: 1 Mobile Arm Holder
- Item #: 1 Mobile Upper Curved Arm
- Item #: 1 Mobile Tri-shaped Arm
- Item #: 3 Toy Animal
- Item #: 1 Wind Up
Note: Toys and mobile may vary.
General Instructions
Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE.
Safety Warnings
⚠️ WARNING: Failure to follow these warnings and the instructions could result in serious injury or death.
Fall Hazard
To help prevent falls, do not use this product when the infant begins to push up on hands and knees or has reached the height of 25 in. (635 mm), weight of 15 lbs. (6.8 kgs) or 4 months old, whichever comes first.
Suffocation Hazard
Infants can suffocate:
- In gaps between a mattress too small or too thick and product sides
- On soft bedding
Never add a mattress, pillow, comforter, or padding. Use only the mattress provided by manufacturer. Never use a water mattress with this product.
Strangulation Hazard
Strings can cause strangulation! NEVER place items with a string around a child's neck such as hood strings or pacifier cords. NEVER suspend strings over playard or attach strings to toys.
NEVER place product near a window where cords from blinds or drapes can strangle a child.
General Safety Precautions
- The playard, including side rails, must be fully erected prior to use. Make sure latches are secure.
- Always provide the supervision necessary for the continued safety of your child. When used for playing, NEVER leave child unattended.
- To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their back to sleep, unless otherwise advised by your physician.
- Child can become entrapped and die when improvised netting or covers are placed on top of a play yard. Never add such items to confine child in play yard.
- NEVER use this product if there are any loose or missing fasteners, loose joints, broken parts, or torn mesh/fabric. Check before assembly and periodically during use. Contact Baby Trend Customer Service at 1-800-328-7363 for replacement parts, repair or instructions. NEVER substitute parts.
- NEVER leave child in product with sides lowered. Be sure sides are in raised and locked position whenever child is in product.
- NEVER use plastic shipping bags or other plastic film as mattress covers not sold and intended for that purpose. They can cause suffocation.
- This product is not intended for commercial use.
Assembly Instructions
To Assemble Playard
Unzip bag and remove Playard frame (Fig. 1). Undo the Fasten straps and set the Mattress aside.
DO NOT push center down yet.
Figure 1 shows the playard frame being removed from its bag.
Top rails must be fully erected before lowering center. Pull up one rail at a time, hold one hand on each side of the rail and pull up sharply. Do not pull from the middle where the center latch release is located. Make sure both tubes latch in place and each rail is rigid. (Fig. 2)
IMPORTANT: The center must be raised while locking the rails. If one rail locks but the other side does not, unlock the rail by squeezing the release in the center and try again.
Figure 2 illustrates the correct way to pull up the top rails.
Once all four (4) top rails are locked in place, push down on the center handle (Fig. 3a). The center mechanism will rotate clockwise 90 degrees and automatically lock in place.
IMPORTANT: Test each top rail by pushing down slightly to confirm each is rigid and securely in place before use. (Fig. 3b)
Figure 3a shows pushing the center handle down. Figure 3b shows testing the rigidity of a top rail.
Place the Mattress on the floor of the Playard with the padded side facing up. (Fig. 4)
Figure 4 shows placing the mattress into the playard.
Insert the Velcro® straps located on the underside of the Mattress through the slots in the floor of each end of the Playard (Fig. 5a). Fasten the hook and loop straps to the underside of the Playard floor to prevent the Mattress from moving. (Fig. 5b)
IMPORTANT: The handle located in the center of the Playard floor MUST remain raised (Approx. 45.7 cm or 18 inches) while locking the side rails in place. If the center is not raised, the rails will NOT lock. If you experience difficulty and one side of the rail will lock but the other side will not, unlock the rail by squeezing the release in the center and try again. If you still have difficulty, contact Customer Service at 1-800-328-7363 or visit www.babytrend.com.
Figure 5a shows inserting Velcro straps through slots. Figure 5b shows fastening the straps.
To operate the brakes on the Wheels, press downward on the brake levers. To release, lift upward on the lever. (Fig. 6)
Figure 6 illustrates operating the wheel brakes.
Folding the Playard
Release the Velcro® straps holding the Mattress from underneath the Playard floor or the Bassinet and set the mattress aside.
Do not unlock top rails yet; the center of the floor must be raised before top rails will unlock.
Rotate the center handle counter-clockwise 90 degrees and raise the center as high as the top rails (Fig. 7). Gather the Legs and Wheels together towards the center as close as possible so that they nearly touch.
Figure 7 shows rotating the center handle before lifting.
Locate the rail latch release in the center and bottom side of each rail. Squeeze the lever with two hands until the rail releases the two tubes (Fig. 8a), then push down (Fig. 8b).
NOTE: If the top rail(s) do not release completely, DO NOT FORCE! Lift the center of floor higher. Both tubes must be released for the top rail to fold.
Figure 8a shows locating the latch release. Figure 8b shows pushing down to fold the rail.
Gather four (4) corners and center all together tightly (Fig. 9). Wrap Mattress around Playard frame with padded side facing inward. Secure the hooks and loop straps by feeding them through the loops on the end of the Mattress and folding them back onto themselves.
Figure 9 shows gathering the corners. The text also describes wrapping the mattress and securing straps.
Secure the hooks and loop straps by feeding them through the loops on the end of the Mattress and folding them back onto themselves. (Fig. 10)
Place folded Playard into carry bag so that the handle comes through the opening between each side of the zipper.
Figure 10 shows securing the straps and placing the playard in the bag.
To Assemble Bassinet
ATTENTION: Playard must be fully assembled and securely locked before installing or using the bassinet feature. You will need to remove the mattress from the bottom of the Playard to use inside your Bassinet.
Position the Bassinet over and down into the fully assembled Playard. Secure in place by pushing down firmly on each plastic support clip until all are snapped into place (Fig. 11).
Figure 11 shows positioning and securing the bassinet.
These tubes must be lined up with the holes in the front frame assembly (Fig. 12a).
Insert both, assembled, Mattress Support Tubes into the loops provided on the bottom of the Bassinet (Fig. 12b).
Figure 12a shows aligning tubes with holes. Figure 12b shows inserting tubes into bassinet loops.
Place the Mattress into the Bassinet with the padded side facing upward (Fig. 13)
Figure 13 shows placing the mattress into the bassinet.
TO REMOVE BASSINET
Remove Mattress from Bassinet. Remove Canopy. Unsnap all clips and lift Bassinet.
To Assemble Changing Table
ATTENTION: Playard must be fully assembled and securely locked before installing or using the changing table feature. (See To Assemble Playard section).
Connect the two (2) Long Curved Bars together. (Fig. 14a)
Insert the assembled curved bars into the Changing Table fabric. (Fig. 14b) Slide the Curved Bars around inside sleeve of the Changing Table.
Connect the two (2) Short Bars to each end of the Long Curved Bar (Fig. 14c) Make sure that the knobs are both facing down and the same direction on each end. (Fig. 14d)
Figures 14a-14d illustrate connecting the changing table bars.
Insert Connector Knob Prongs into holes located on both corners of the Playard (Fig. 15a).
Turn the Connector Knobs counter clockwise to lock into place (Fig. 15b).
Flip Changing Table over onto Playard (Fig. 15c).
Snap the two (2) buttons on the flap down onto the Playard (Fig. 15d).
IMPORTANT: Check that the Changing Table is correctly and securely installed BEFORE each use.
Figures 15a-15d show securing the changing table to the playard.
TO SECURE THE CHANGING TABLE TO THE PLAYARD
IMPORTANT! When the changing table is flipped up into the upper position, the changing table must be secured to the playard frame using the velcro straps provided.
Locate the Velcro straps on the bottom of the changing table and on inside of the side rails of the playard. (Fig. 16)
Figure 16 shows locating Velcro straps.
Flip the changing table into its upper position. (Fig. 17)
Figure 17 shows flipping the changing table.
Secure the changing table to the playard frame by fastening the Velcro straps on the underside of the changing table to the side rails of the playard frame. (Fig. 18)
Figure 18 shows securing the changing table with straps.
To Use Changing Table Restraint System
Place child on changing table, make sure hand and arms are clear of the restraint. Bring the restraint around the child's waist and clip the male and female ends of the buckle together. (Fig. 19a)
Tighten strap until it fits snug around child's waist. DO NOT OVER TIGHTEN. (Fig. 19b)
To remove, unsnap the buckle.
ATTENTION: NEVER use changing table if it is damaged or broken.
Figures 19a and 19b illustrate using the restraint system.
To Remove Changing Table
Flip Changing Table to the outside of the Playard. Unsnap fabric flap of Changing Table from Playard. Twist Connector Knobs clockwise to unlock. (Fig. 20a) Remove Changing Table from Playard (Fig. 20b) and disconnect the Short Bars from the Curved Bar by pressing on the snap buttons and pulling apart. Remove Curved Bar from Changing Table sleeve.
Figures 20a and 20b show the process of removing the changing table.
Parent Organizer Assembly
Parent Organizer: Position each hook so that the hooked end is facing the rear side of the organizer. Press the hook down firmly into the slot until it snaps into place. (Fig. 21a)
Diaper Stacker: Skip to step 2.
Connect the Parent Organizer/Diaper Stacker to the Playard by sliding the two (2) connecting clips over an open portion of the top rail of the Playard. (Fig. 21b)
NOTE: The Parent Organizer/Diaper Stacker can only be installed on open sides of the Playard where the connecting clips can easily be attached without interfering with other features.
Figures 21a and 21b show attaching the parent organizer/diaper stacker.
Mobile Assembly
ATTENTION: A crib mobile is intended for visual stimulation and not to be grasped by the child. If attached to the crib or playpen, remove when baby begins to push up on hands and knees. If so designed, mount on wall or ceiling clearly out of a standing baby's reach. Always attach all provided fasteners tightly to a crib or playpen according to the instructions. Check frequently. DO NOT add additional strings and straps. DO NOT attach the Mobile with child in Playard or Bassinet.
Insert the Mobile Lower Arm (a) into the Mobile Arm Holder (b) until they lock together. (Fig. 22)
Figure 22 shows inserting the lower arm into the holder.
Insert the Mobile Upper Curved Arm (c) into the Mobile Lower Arm (a, b) until locked together. (Fig. 23)
Figure 23 shows inserting the upper curved arm.
Attach the Wind up (f) to the Tri-shaped Arm (d), align slots on both pieces then gently press the two pieces together. (Fig. 24)
Figure 24 shows attaching the wind-up mechanism.
Snap the Wind up (f) with Tri-shaped Arm (d) onto the end of the Upper Curved Arm (a, b, c) (Fig. 25). Connect each of the three Toys (e) to the Mobile by threading the string into the slot at the end of each arm.
Figure 25 shows attaching the assembled mobile parts and toys.
Insert the bottom of the Mobile Arm into the frame of the Playard. (Fig. 26)
Figure 26 shows inserting the mobile arm into the playard frame.
Maintenance and Cleaning Instructions
- Use only household mild soap and warm water.
- DO NOT USE BLEACH.
- DO NOT MACHINE WASH.
Customer Service
If you experience any difficulty with assembly, missing parts or use, please DO NOT return this item to the store. Retail stores are unable to properly assist you. Contact our Customer Service Department directly for assistance.
Call toll-free 1-800-328-7363, Monday - Friday, between the hours of 8:00 a.m. and 4:30 p.m. (PST).
Baby Trend, Inc.
1607 S. Campus Ave., Ontario, CA 91761
www.babytrend.com
