LDT 050042 Service-Module for Decoder for Switchboard Lights Instruction Manual
File info: application/pdf · 2 pages · 244.07KB
gbs-service 04 10 en
en:dl gbs dec [LDT]
Service-Module for Decoder for Switchboard Lights
Extracted Text
Littfinski DatenTechnik (LDT) Operating Instruction Service-Module for Decoder for Switchboard Lights from the Digital-Professional-Series ! GBS-Service-F Part-No.: 050042 >> finished module << Suitable for the Decoder for Switchboard Lights GBS-DEC and the KeyCommander KeyCom for setting addresses and operation mode. If the Service-Module GBS-Service will be connected to the Master-Module of the Decoder for Switchboard Lights or to the KeyCommander, the setting of addresses and operating mode can be carried out with 4 keys and a 16-digit lc-display. This product is not a toy! Not suitable for children under 14 years of age! The kit contains small parts, which should be kept away from children under 3! Improper use will imply danger of injuring due to sharp edges and tips! Please store this instruction carefully. Colored sample connections can be found on our Web-Site www.ldt-infocenter.com at the section "Sample Connections". On which Master-Module (GBS-Master-MM, GBS-Master-DC or GBS-Master-s88) the Service-Module shall operate is indifferent. At the first start of operation on a Master-Module or a KeyCommander, please turn carefully the trim-pot R1 a half turn to the right or left by using a small screw driver until you receive an optimal reading of the information at the display. Now is the Service-Module ready for operation. The further application of the module will be explained within the operating instruction of the Master-Module respectively the KeyCommander. Introduction/Safety instruction: You have purchased the Service-Module GBS-Service for the Decoder for Switchboard Lights GBS-DEC for your model railway. The Service-Module GBS-Service is a high quality product that is supplied within the Digital-Professional-Series of Littfinski DatenTechnik (LDT). We are wishing you having a good time using this product. The finished module comes with 24 month warranty. � Please read the following instructions carefully. Warranty will expire due to damages caused by disregarding the operating instructions. LDT will also not be liable for any consequential damages caused by improper use or installation. � We designed our devices for indoor use only. Connect the Service-Module GBS-Service to the Master-Module GBS-Master: � Attention: Before starting the installation switch off the drive voltage by pushing the stop button or disconnect the main supply. Connect the 15-poles pin-plug of the Service-Module GBSService to the 15-poles socket-plug of the Master-Module GBS-Master or to the KeyCommander. Avoid any offset of the pin contact strip to the correct socket connection. Mode of operation: The Service-Module GBS-Service can operate only together with a Master-Module GBS-Master or a KeyCommander as it relays to the operating voltage and data of those modules. Further products from our DigitalProfessional-Series: S-DEC-4 4-fold turnout decoder for four magnet accessories and 1A switching current each. With free programmable decoder address. M-DEC 4-fold decoder for motor driven turnouts (Conrad, Hoffmann, Fulgurex etc.) with free programmable decoder address and possible external power supply. SA-DEC-4 4-fold switch decoder with four bistable relays of 2A switching current each and free programmable decoder address. RM- 88-N / RM-88-N-Opto 16-fold feedback module for the s88-feedback bus. For s88standard connections and connections to s88-N. RM-GB-8-N 8-fold feedback module with integrated track occupancy detectors for the s88-feedback bus. For s88-standard connections and connections to s88-N. All components are available as easy to assemble complete kits as finished modules or as finished modules in a case. Picture 1: The Service-Module GBS-Service connected to the Master-Module GBS-Master via the 15-poles pin plug. 14 13 12 11 10 9 GBS-Display / Light-Display Rev. 1.8 8 7 6 5 4 3 2 1 Von Steuereinheit oder Booster From command station or booster J K braun rot brown red JK s88 br. rt IN ST2 s88 OUT ST1 KL1 KL2 KL1 R1 BU2 ST1 ST1 BU1 white weiss 37 36 KL5 KL6 BU2 gelb braun 39 38 40 10...18V~ 12...24V= braun brown gelb yellow Vom Modellbahntrafo From transformer IN GBS-Master Rev. 1.3 Littfinski DatenTechnik (LDT) S2 S3 S4 Littfinski DatenTechnik (LDT) GBS-Service S1 Rev. 1.0 GBS-Service Modul aufstecken connect GBS-Service Module KeyCom KeyCommander Rev. 1.1 ST2 booster Picture 2: The Service Module GBS-Service connected to the KeyCommander KeyCom via the 15-poles pin plug. R1 ST1 Littfinski DatenTechnik (LDT) Littfinski DatenTechnik (LDT) www.ldt-infocenter.com Digital-Profi werden! KeyCommander KeyCom-DC Weichen und Signale digital �ber Taster schalten. Digitalformat: DCC. BU1 LED2 + LED1 Go Stop Go + S2 S1 Stop KL1 gelb braun 14...18V~ ST1 s88-bus S2 S3 S4 Littfinski DatenTechnik (LDT) GBS-Service S1 Rev. 1.0 Service Modul aufstecken connect Service Module Made in Europe by Littfinski DatenTechnik (LDT) B�hler electronic GmbH Ulmenstra�e 43 15370 Fredersdorf / Germany Phone: +49 (0) 33439 / 867-0 Internet: www.ldt-infocenter.com Subject to technical changes and errors. � 09/2022 by LDT
de:ldt-infocenter [LDT]