User Manual for Jimi IoT models including: LL301, Wireless Tracker for Asset Vehicles, LL301 Wireless Tracker for Asset Vehicles
LTE Cat.1 Asset GNSS Tracker
As the product is in constant upgrade, no prior notice will be sent to you for any update in this User Manual. Appearance. GSM LED. Notch. 4*Blue (battery level).
il y a 23 heures — As the product is in constant upgrade, no prior notice will be sent to you for any update in this User Manual. Appearance. GSM LED. Notch. 4*Blue (battery level).
File Info : application/pdf, 13 Pages, 2.02MB
DocumentDocumentLL301 Wireless Tracker for Asset Vehicles User Manual Version:V1.2 Read this manual carefully prior to use to ensure fast and correct operation of the product. No prior notice will be given for any changes made to the appearance, color, or accessories of the product. Introduction Features Power saving Multi-GNSS positioning Large-capacity battery Remote listening Tamper alert Cover removal alert Humidity and temperature detection and alert CommuIPnxi4captriootnecstyiosntem: Specification Communication system: LL301E LTE FDD : B1//B3/B7/B8/ B20/B28 GSM: 900/1800MHz LL301L Listening range: 5m GONpeSrSataincgcucruarcryent: <30mA Listening range: 5m Operating current: <30mA LEDs Operating temperature Dimensions (LxWxH) LTE FDD : B1/B2/B3/B4/B5 /B7/B8/B28/B66 G5SmM: 850/900/1800/1900MHz <10m 5m <30mA 1*Red (work status) and 4*Blue (battery level) Operating temperature Dimensions (LxWxH) 20 to +70 108x61x30mm Packing List Name Tracker User Manual Charging cable 3M Tape Bracket Standard Unit Qty PCS 1 PCS 1 PCS 1 PCS 1 PCS 1 Remarks / / / / / Note: Please check the received package against the packing list. The contents are subject to actual items. As the product is in constant upgrade, no prior notice will be sent to you for any update in this User Manual. Appearance MIC GSM LED Notch MIC SIM card holder Battery switch Cover removal detection switch emperature and Humidity sensor Anti-tamper button Note: Once the anti-tamper button is released, a tamper alert will be triggered. Power LED Plug for power button and USB port GSM LED Status Fast blink Slow blink Solid on Meaning GSM initializing/No GSM signal/ No SIM card Logging in to platform Device in a call Note: The GSM LED goes off 3 minutes later after the device is turned on. The GSM LED will light up by short pressing the power button of the device in the power-on state and go off after 60 seconds. Power LED If the device is charging, then: Strength 025% 2550% 5075% 7596% Charging complete LED1 1s1s (onoff) On On On On LED2 Off 1s1s (onoff) On On On LED3 Off Off 1s1s (onoff) On On LED4 Off Off Off On On If the device is not charging, then: Strength Undervoltage 025% 2550% 5075% 75100% LED1 Off On On On On LED2 Off Off On On On LED3 Off Off Off On On LED4 Off Off Off Off On Note: The power LED goes off 3 minutes later after the device is turned on. The power LED will light up by short pressing the power button of the device in the power-on state and go off after 20 seconds. Notes on Work Modes Timed mode: In this mode, the device uploads position fixes at a fixed interval, which is configured via the location service platform or mobile app specified by your dealer. Smart mode (default): In this mode, the device tracks the vehicle in real-time, records the trips of the vehicle, and can differentiate moving state from parking state. If the vehicle moves, the GPRS connection is persistent and the device will upload a position fix every 20 seconds. If the vehicle stops, the device will enter the sleep mode and no position fix will be uploaded. Long standby mode: The device will wake up at a certain configured interval to upload position fixes. After each upload is complete, the device will enter deep sleep and will not execute any remote query or set actions. Tamper Alert When the device is attached to a vehicle, the anti-tamper button will remain press-down. If the device is detached, the anti-tamper button will spring back, which will trigger the device to send out a tamper alert. In the long standby mode, the device will enable tracking for 20 minutes after the alert message is sent out. The tamper alert feature can be disabled by command. Cover Removal Alert When the front cover of the device is in place, the cover removal detection switch will remain press-down. If the cover is opened, the switch will spring back, which will trigger the device to send out a removal alert. In the long standby mode, the device will enable the smart mode for 20 minutes after the alert message is sent out. The removal alert can be disabled by command. Attaching SIM and Description about Power-On and -Off Tips: 1. Activate GPRS and SMS services of the SIM card. 2. Power off the device (battery switch to OFF) before attaching or detaching the SIM card. Attaching the SIM Card Remove the back cover by the notch, slide the battery switch to OFF, and insert the SIM. Notch Confirm thatthe battery switch is off Insert the SIM Power-On and -Off Power-on: Press the power button for 3 seconds (prerequisite: the battery switch is ON). Power-off: Press the power button for 3 seconds. Installing the Device The device has a strong magnet built inside. It can attach to any ferromagnetic material. The magnet makes the installation easy. Or you can stick the 3M tapes on one side of the device bracket, and attach the bracket to the target object, then put the device on the bracket. 3M Tape Bracket Platform Operations After binding the device on the location service platform or mobile app designated by the dealer, you can monitor it, configure it, and do more to it via the platform or app. Logging In to Service Platform You can configure and control the device via the designated location service platform. Downloading Mobile App You can download the mobile app via the URL provided by your dealer. Precautions Please use batteries and accessories specified by the manufacturer of the device; otherwise, the warranty will become void. The manufacturer of the device shall bear no warranty liabilities for any damage resulted from the use of non-original accessories. Do not soak the battery in water or expose it to fire. Do not bend or forcibly open the battery. Do not disassemble the battery as the device may be damaged if the disassembly is done improperly by a non-professional. Troubleshootintg When a problem arises, you can troubleshoot it by the following solution. If the problem persists, please don't hesitate to contact your dealer or service provider. Common Issues Poor signal Possible Causes The device is used in an area where radio waves is hard to reach, such as near high-rise buildings or in a basement. Power-on failure No SIM Battery switch is not set to ON. The battery is exhausted. The SIM card may be attached improperly. Failed to access the network The metal side of the SIM card is stained. The SIM is invalid. The device is out of service areas. The signal is extremely weak. Failed to query a location The SIM is not activated with data service. The device keeps replying with "No data found, please try again". Solutions Try it in a place where satellite signals can be well received. Insert a SIM. Slide the battery switch to ON. Charge the device. Check the SIM. Wipe it with a clean cloth. Please contact your network service provider. Try it in a service area. Try it in an area with strong signals. Please contact your network service provider and activate the data service. Please contact your dealer. Warranty Instructions and Service Special Statement No prior notice will be given if the product is upgraded due to technological reasons. The appearance or color of the product is subject to the actual. The warranty card applies to the services of repair, replacement, and refund of the product with the following IMEI. Please keep this warranty card and the original purchase receipt together in a safe place, as these will be needed at time of services. Warranty Terms For damages not caused by human factors, this warranty lasts for 2 (two) years (including one-year replacement service) from the date of the original purchase. You can choose to pay for the repair services in any of the following cases: The warranty card expires; No warranty card or valid proof of purchase; The product, including its accessories, is not in the warranty period; Damage caused by unauthorized repairs, crash, liquid spillage, incident, accident, modifications, or incorrect voltage input; or the label, IMEI, or counterfeit mark of the product is broken or scribbled; Damages caused by installation or use not in accordance with the user manual; Damage caused by force majeure such as fire, flood, or lightning; The device model is inconsistent with the warranty card or the warranty card has been altered; Other damages caused by force majeure. Reminder For vehicle trackers: As of January 1, 2016, the warranty lasts for 2 (two) years for repair from the date of purchase, including one year for replacement. The specific terms are: A full replacement, including accessories, if the product is found defective during unpacking check; If a defect occurs within one year after installation, then: Replace only the mainboard if the housing is intact and doesn't affect normal use; or Replace the housing and the mainboard if the housing is defective and affects normal use (Please be noted that man-made damages will void the replacement service for the housing). Free repair services will be given to the product if a defect is found during the second year under proper use. FCC warning Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your bodyAdobe PDF library 15.00 Adobe Illustrator 24.3 (Windows)