User Manual for Rayrun models including: P11 Single Color LED Wireless Remote Controller, P11, P11 Single Remote Controller, Single Color LED Wireless Remote Controller, Single Color LED Remote Controller, LED Wireless Remote Controller, LED Remote Controller, LED Wireless Controller, Wireless Controller, Remote Controller, LED Controller, Controller
P11 Pro. RF Single Color LED Dimmer-Rayrun
Wireless Remote Control
Single Color LED Controller
Model: P11(-S)
Introduction
P11 single color LED controller is designed to drive constant voltage LED products in voltage range of DC524V. The main unit works with a RF remote controller, user can setup LED brightness with shortcut keys from the remote controller. The main unit is powered by DC power supply and receives remote controller commands to drive LED fixtures.
Full Protection
High Power
Waterproof
Compact Size
Wireless Remote Wide Voltage Range
Wiring & Indicator
1. Power supply input
The controller supply voltage range is from DC 5V to 24V. The red power cable should be connected to power positive and black to negative. (For other cable color, please refer to the labels). The LED output voltage is at same level as the power voltage, please make sure the power supply voltage is correct and the power rating is capable for the load.
2. LED output
Connect constant voltage LED loads. Please connect red cable to LED+ and black cable to LED-. Please make sure the LED rated voltage is same as the power supply and each channel's maximum load current is in range of the controller rated current.
3. Work status indicator This indicator shows all working status of the
controller. It displays different events as following: Steady blue: Normal working. Short white blink: Command received. White blink for 3 times: New remote paired. Single yellow flash : Edge of the content. Red flash: Overload protection. Yellow flash: Overheat protection.
4. Wiring diagram Please connect the controller output to LED loads
and power supply to the controller power input. The power supply voltage must be same as the LED load's rated voltage. Check all cables to be well connected and insulated before power on.
To 110/230 5-24V DC output AC power Power supply
P11 LED Controller
Constant voltage LED load
5-24V DC
5-24V Driving
Remote Controller
Functions
5. Turn ON / OFF Press `I' key to turn on unit or press `O' key to turn off.
Controller will memorize the on/off status and will restore to the previous status on next power on.
Please use remote controller to turn on the unit if it was switched to off status before previous power cut.
8
Press within 10 seconds after receiver powered on
Pair new remote
6. Brightness adjust Press `+' key to increase brightness and press `-' key
to decrease. Hold press `+' or `-' key to adjust brightness smoothly.
7. Brightness shortcut Press these keys to jump to relative brightness level.
The controller applies brightness gamma correction on dimming control, makes the brightness tuning more smooth to human sense. The brightness shortcut level is valued to human sense, and not proportional to the LED output power.
8. Remote indicator This indicator blinks when remote controller works.
The indicator will flash slowly if the battery is empty, please change the remote controller battery in this case. The battery model is CR2032 lithium cell.
Operation
9. Using the remote Please pull out the battery insulate tape before using.
The RF wireless remote signal can pass through some nonmetal barrier. For proper receiving remote signal, please do not install the controller in closed metal parts.
10. Paring a new remote controller The remote controller and main unit is 1 to 1 paired for
factory default. It's possible to pair maximum 5 remote controllers to one main unit and each remote controller could be paired to any main unit.
You could pair a new remote controller to main unit by following steps:
1). Plug off the power of main unit and plug in again after more than 5 seconds.
2). Press and key simultaneously for about 3 seconds, within time of 10 seconds after the main unit powered on.
11. Recognize current remote only
In some cases, one main unit might be paired with several remote controllers but extra remote controllers are no longer needed. User could simply pair the current using remote to main unit again, then the main unit will dis-pair all other remote controllers and recognize current one only.
Advanced features
12. Waterproof (-S version)
The IP-68 waterproof feature with glue injection finish is available on -S version controllers. For overall waterproof performance, the cables must be waterproof treated separately.
Wireless signal degrade : The wireless communication ability could degrade when using at wet environment, please be aware that the wireless control distance will be shortened in such case.
13. Protection function
The controller has full protection function against wrong wiring, load short circuit, overload and overheat. The controller will stop working and the indicator will flash with red / yellow color to indicate the malfunction. The controller will try to recover from protection status in a short time when the working condition is good.
For protection issues, please check the situation with different indicator information:
Red flash: Check the output cables and load, make sure no short circuit and the load current is in rated range. Also the load must be constant voltage type.
Yellow flash: Check the installation environment, make sure in a rated temperature range and with good ventilation or heat dissipation condition.
Model Brightness grade
PWM grade Overload protection Overheat protection
Working voltage Remote frequency Remote control distance Rated output current
IP Grade
P11
P11-S
100 levels
4000 steps
Yes
Yes
DC 5-24V
433.92MHz
>15m at open area 1x15A
IP63
IP68
RF
LED
:P11(-S)
P11LED5V 2 4 VL E D L E D L E D L E D L E D
1.
5V24V L E D
2.LED
L E D L E D P W M L E D LEDLED
3.
3
4.
LED L E D
5-24V
5-24VDC
LED
LED
RF
5. "I " "O "
/
8
10
6.
7. 100%80%60%
4 0 %2 0 %1 0 %
LED
8.
CR2032
9.
R F
10. 11 1
5
1 5 210 3 3
11.
12.IP68(-S)
-S I P 6 8
13.
PWM
P11
P11-S
100
4000
DC5-24V
433.92MHz
>15
15A
IP-63
IP-68
Corel PDF Engine Version 18.1.0.661 CorelDRAW X8