Bromic Refrigeration Instruction Manual

1. Prefix

This manual contains important information regarding the installation, operation, and maintenance of Bromic MediFridge™. Please pay close attention to the safety information provided throughout this manual. Safety information is accompanied by the following alert symbols:

DANGER, WARNING, IMPORTANT

• READ THIS MANUAL CAREFULLY before installing or servicing this product.
• Improper installation, operation, or maintenance can result in death, severe injury, or property damage.
• This appliance is intended for 230-240 Volt power supply.
• Installation MUST be carried out by a licensed and authorised technician in accordance with local electrical codes.

2. Important Notes and Warnings

• Read all instructions before installing or using this appliance.
• Retain this manual for future reference.
• Use this appliance only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
• Improper installation, adjustment, alteration, or failure to follow the warnings and instructions in this manual could result in severe personal injury, death, or property damage.
• The manufacturer is not responsible for any damage that could occur from improper use. The manufacturer emphasizes that this appliance should be used in a responsible manner and that all procedures, warnings, and safety instructions contained in this booklet be followed strictly.
• Check the appliance for damage. Do not operate a damaged unit.
• Check for damage to the appliance regularly. If damage is suspected, discontinue use immediately and contact the supplier or a qualified person for repair.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Keep packaging material out of reach of children.
• Children should be carefully supervised to ensure they do not play with the appliance.
• Do not attempt to alter the appliance in any manner.
• Pay attention to the maximum load limit when filling the shelves.
• All work on electrical equipment must be carried out by a qualified and licensed technician only.
• Do not perform maintenance until the appliance has been turned off and power disconnected.
• Never detach any cover except where specifically instructed in this manual, as doing so might expose live electrical parts.
• Do not operate the appliance with panels, covers, or guards removed.
• Keep the air intake and outlets free of obstructions.
• Do not use the appliance outdoors.
• If the supply cord becomes damaged, it must be replaced by an authorized service agent or similarly qualified person to avoid a hazard.
• If the appliance has not been used, or will not be used for a long period, disconnect the power supply.
• Ensure the appliance has adequate ventilation.
• The top of the cabinet should not be used for storage of any objects and must be clean and dry at all times.

Caution: Risk of fire ⚠️

3. Product Overview

4. Installation

Note: The maximum ambient temperature for the refrigerator is 30°C. Conditions outside this temperature will result in cabinet temperatures outside the required 2 to 8°C range. Bromic recommends that the refrigerator is installed at an ambient temperature of 20 to 25°C.

Locating the Cabinet

Ensure the following instructions are observed for proper and trouble-free operation:

• Do not install the cabinet outdoors.
• Locate the appliance in a dry and well-ventilated place.
• The unit must be positioned on a level surface.
• Do not install in the vicinity of heating radiators or other heat sources.
• Do not install the appliance where it is exposed to direct sunlight.
• Do not install the appliance where it is exposed to warm draughts or open doors.
• Keep the air intake and outlets free of obstructions.
• Adequate allowance should be made for door openings.

Diagrams showing airflow around the unit and clearance requirements:

• Diagram 1: Shows airflow from the front and sides, indicating the need for clearance.
• Diagram 2: Shows a starburst pattern indicating heat or pressure, emphasizing avoiding heat sources.
• Diagram 3: Shows arrows indicating air circulation around the unit, highlighting ventilation.
• Diagram 4: Shows a door opening, indicating the need for space to open the door.

Ventilation

Ensure the following instructions are observed for proper and trouble-free operation:

• Allow 100mm clearance between walls and the appliance.
• Ensure that the condenser fan is free to take in ambient air from the room.
• Adherence to minimum clearances is necessary.

Diagrams showing required clearances:

• Side View: Shows 100mm clearance required on the side.
• Front View: Shows 100mm clearance required at the top and sides.

Power Supply

• The appliance must not be plugged into a multiple outlet power board.
• The appliance is supplied with a flexible power cord fitted with a 3-pin plug.
• The socket used must be properly earthed and fuse protected.
• Refer to the rating label inside the cabinet for supply voltage, frequency, and current draw.
• The power cable is rated 70°C. It is recommended that the cable should not come into contact with parts over 50°C.
• Do not turn off power before consulting the person responsible.
• Mark the power source clearly so the refrigerator is not unplugged or turned off accidentally.

Diagrams showing correct and incorrect power connections:

• Correct: A single 3-pin plug connected to a wall socket.
• Incorrect: A 3-pin plug connected to a multi-outlet power board with a red cross over it.

Before Operating

• If the appliance has been sharply tilted or transported horizontally, it must be left to stand upright and not plugged in for 1 hour.
• Remove all packaging material before using the appliance.
• Start the appliance only if it has been installed as described.

5. Operation

Start-up

• Connect the appliance to the mains power supply and check that the compressor, electronic controller, lighting, and all fans are functioning correctly.
• The compressor and condenser fan should operate approximately 3 minutes after the unit has been connected to the power supply.
• The evaporator fan should operate after the unit has been plugged in.
• The electronic controller will display the current cabinet temperature after the unit has been connected to the power supply.
• The ❄️ LED indicates that the refrigeration circuit is operating.
• During the start-up delay (3 minutes), the ❄️ LED is flashing.
• The ♨️ LED indicates that the refrigeration circuit is defrosting.

Setting the Temperature

Note: The controller is factory set at 4°C. The controller is programmed to control cabinet temperatures between 2 to 8°C.

Control Panel Diagram:

• Shows buttons for Up (▲), Down (▼), Set (SET), and Mode (P).
• Digital display showing temperature (e.g., 0.5).
• Indicators for HI and LO temperature settings.
• Indicators for Celsius (°C) and Fahrenheit (°F).

To set the temperature:

1. Press the SET button.
2. The set temperature will be displayed.
3. Press ▲ or ▼ to adjust the temperature.
4. Press the SET button to exit. If no further buttons are pressed within 6 seconds, the cabinet temperature will be displayed.

Display the Product Sensor Temperature

1. Press the ❄️ button.
2. The product temperature will flash and display.
3. After 6 seconds, the cabinet temperature will be displayed.

Operating the Light

1. Press the ? button to turn internal LED lights ON or OFF.

MAX / MIN Temperature Recording

IMPORTANT: Record the maximum and minimum temperatures two (2) times a day. Recordings should be taken before the first door opening of the day.

1. Press the HI/LO button once.
2. The highest temperature recording will be displayed.
3. Press the HI/LO button again while the highest temperature recording is displayed.
4. The lowest temperature recording will be displayed.
5. To clear the MAX/MIN recording - Hold the HI/LO button for 6 seconds.
6. The display will flash for 3 seconds and the buzzer will sound, clearing the previous highest and lowest temperature recordings.
7. The current cabinet temperature will be recorded.

Controller Alarms

If alarms persist, contact the manufacturer or an approved service agent.

6. Product Loading and Storage

WARNING: Failure to follow the guidelines below will result in cabinet temperatures above 8°C.

IMPORTANT: Run the refrigerator for at least 2 hours before loading.

Start-up

• Clean the interior surface with a soft cloth and warm water before loading.
• Ensure there is free circulation of air between the products.
• Do not block the evaporator fan.
• Do not overstock the refrigerator.
• Use cold mass (e.g., water bottles) on unused shelves.
• Keep refrigerator door openings to a minimum.
• Ensure products are between 2 and 8°C before loading. If there is a breach in the cold chain, isolate the affected products. Do not use or discard until advice is given.
• Some products are sensitive to ultraviolet (UV) light; please see storage guidelines from the manufacturer before removing from packaging.
• Do not store food and other goods in the refrigerator.
• Maximum recommended shelf load is 20kg.

Note: Bromic cannot be responsible for loss of stock or damage to stock.

Please refer to the 'National Vaccine Storage Guidelines: Strive for 5' for more information on vaccine storage and handling or contact your local state or territory health department. (https://www.health.gov.au/internet/immunise/publishing.nsf/content/IMM77-cnt)

7. Maintenance

WARNING: Disconnect the appliance from the power supply before performing any maintenance. Never unplug the appliance by pulling on the cord. Always grasp the plug firmly and pull straight out of the outlet.

WARNING: Exposure to significant water ingress will void warranty and cause potential safety issues. If the unit is exposed to water, please contact the manufacturer immediately.

IMPORTANT: Warranty may be void if there is no evidence of preventative maintenance performed on the appliance.

Cleaning the Cabinet

• Remove the products and transfer them to a suitable location prior to cleaning the inside of the cabinet.
• Do not use any aggressive or abrasive cleaning agents.
• Never use a water hose or a high-pressure jet to clean.
• Do not use sharp or pointed objects for cleaning.
• Clean the inside and outside of the appliance with a clean damp cloth or a neutral cleanser.
• Dry all surfaces with a dry cloth.

Condenser Coil

IMPORTANT: The condenser coil must be cleaned with a vacuum or brush once a month. The condenser coil must be cleaned regularly to maintain performance and minimize power consumption. A poorly maintained condenser coil can lead to unit failure and cabinet temperatures above 8°C.

Extended Defrosting

The evaporator (cooling) coil of the refrigerator may build up a layer of ice over time, reducing performance. Inspect the evaporator coil for ice build-up regularly. For extended defrosting, turn off the unit with the door opened for a period of 24 hours.

8. Troubleshooting

IMPORTANT: Repairs on the unit must be carried out by an authorized and licensed person only. Contact the manufacturer or an approved service agent for any repairs needed.

9. Schematic Diagram

Diagram showing the electrical components of the refrigerator, including:

• Power Plug (L, N, E)
• Evaporator Fan
• Temperature Controller (with sensors for room and goods)
• Compressor
• Condenser Fan
• Overload Protector
• Battery
• Alarm output
• COMP, LIG, LEN, POWER, AC/DC labels
• Wiring connections (e.g., YL/GN for ground)

10. Environmental and Disposal Notes

These refrigerated cabinets are designed to high standards of environmental protection and recycling convenience. Cyclopentane, an environmentally friendly foaming agent, has been used. Cyclopentane has zero ozone depletion potential (ODP) and zero global warming potential (GWP). The refrigerant used in the hermetically sealed circuit is environmentally friendly, contains no chlorine, and has zero ODP.

The device must be disposed of in accordance with applicable regulations. WEEE regulations must be observed.

To prevent environmental nuisance and promote the reuse of high-quality materials, used commercial refrigeration equipment must be collected for expert disposal and recycling. Observe the following disposal regulations:

• The cabinet must not be discarded with regular waste.
• The refrigeration circuit must not be damaged.
• Before disposal, make the unit unserviceable by disconnecting the power plug and cutting off the power cable.
• Consult your local authorities or authorized dealers for details of collection and disposal facilities.

Children are often unable to recognize the dangers associated with commercial refrigeration equipment. Proper supervision must be maintained, and children must be prevented from playing with discarded refrigerated cabinets.

11. Warranty

All Bromic products are manufactured to the highest quality standards and are supported by our Extra Care Service Warranty, including guarantees against material or workmanship defects that cannot be excluded under Australian Consumer Law.

Warranty terms vary across the range. Please ensure you are familiar with the Terms and Conditions applicable to your Bromic product purchase by referring to the Warranty Policy included with your product.

Alternatively, you can download the Warranty Policy at: https://bromicrefrigeration.com.au/extra-care-warranty

How to Place a Service Request

• Please call 1300 276 642 to place a warranty service request and inform the operator whether you need Priority A or B service. More information can be found below.
• Ensure you have the serial number of your product ready before contacting us.
• The serial number of your product can be found on a compliance plate located on the inside right and at the rear of your cabinet.

Compliance Plate Example:

P/N#: 3735161-NR

Serial number: ST21113A01GH65T004

Description: CHILLER UC0650SD-NR, UPRIGHT 1DR 650L S/S

Model: UC0650SD-NR

Description: Ventilated

Electrical: AC220-240V 50Hz 1Ph

Made in China

Bromic Model: UC0650SD-NR

Bromic Part no.: 3735161-NR

Refrigerant type: R290

Rated Voltage: AC220~240V

Frequency: 50 Hz

Power: 120 W

Rated current: 3.0A

Net Weight: 135Kg

Rated Wattage: 305W

Max Lamp Wattage: 1.5W

Made in China

Service Request Priority

Priority A Service: When the unit is NOT performing its primary function (e.g., cooling or heating), or presents an OH&S or food safety risk.

Priority B Service: When the unit is performing its primary function and presents no OH&S or food safety risk (e.g., lights, gaskets, locks, door adjustment).

Service Call Placement Times:

• Service Call Placed Before Midday:
  Priority A - Technician to attend site within 4 hours.
  Priority B - Technician to attend site within 8 business hours.
• Service Call Placed After Midday:
  Priority A - Technician attends site before midday on the following business day.
  Priority B - Technician attends site before 4pm on the following business day.