WasteMaster Rubbish Compactor

Waste Master Operation

1. Ensure the bin is completely open and the lid is folded back.
2. Place the claws over the bin handles and allow the bottom of the compactor base to contact the waste in the bin.
3. Standing at the front of the bin, pull back on the unit allowing the claws to "lock" onto the bin handles. Pull down on the handle so the compactor base can depress the waste within the bin.
4. Repeat several times until waste within the bin is at the desired level.
5. Remove the Waste Master and store it on the back of the bin, attached to the handles.

Please note: Do not use excessive force or "hang off" the handle when using the unit, as this may cause damage to the bin or possible injury.

Waste Master Working Specifications

• The unit is suitable for most 120 and 240 litre bins.
• The unit is designed for soft general household or commercial waste.
• The unit should not be used to compress metal, timber, or hard plastic, as this will damage the unit and/or the bin.
• It is recommended the unit should be kept out of direct sunlight and rain.

Assembly Instructions

Box Contents

Tools Required

Two 13mm open-ended spanners or shifters.

Parts List

• A Compactor Base: 1
• B Connector Legs: 2
• C Handle: 1
• D Locking Arms: 2
• E 40mm Bolts: 4
• F Nylon Washers: 14
• G Locking Nuts: 6
• H 70mm Bolts: 2

Assembly Steps

Step 1

Connect the lower bolt hole of the Connector Legs (B) to the corresponding fitting on the Compactor Base (A). Use one 40mm Bolt (E), two Nylon Washers (F) (one on each side of the connection), and one Locking Nut (G) for each hole marked with an arrow in the diagram. Ensure a nylon washer is placed on both the nut and bolt head side of the fitting. The locking nut must be fitted with the black internal washer and recessed edge facing outwards. Once done, tighten so the connection is firm and the locking nut has made full contact with the thread of the bolt. Ensure the base can swing freely.

Step 2

Align and connect the upper bolt hole of the Locking Arms (D) to the Handle (C). Use one 40mm Bolt (E), two Nylon Washers (F), and one Locking Nut (G) for each hole marked with an arrow in the diagram. Ensure a nylon washer is placed on both the nut and bolt head side of the fitting. The locking nut must be fitted with the black internal washer and recessed edge facing outwards. Tighten until the connection is firm and the locking nut has made full contact with the thread of the bolt.

Step 3

Connect the assembled sections from Step 1 and Step 2. Use one 70mm Bolt (H), three Nylon Washers (F), and one Locking Nut (G) for each connection marked with an arrow in the diagram. Ensure a nylon washer is placed on both the nut and bolt head side of the fitting. The locking nut must be fitted with the black internal washer and recessed edge facing outwards. Tighten until the connection is firm and the locking nut has made full contact with the thread of the bolt. Ensure the base can swing freely.

Important Notes for Assembly

Orientation: Ensure that the claws are facing down and the single "U" section of the Compactor Base is facing towards the handle and away from the "claws".

Tightening: Do not over-tighten. Ensure the base can swing freely.

Support & Warranty

Distributed by: ACM PTY LTD, Suite 20, 45-51 Ringwood St, Ringwood, Victoria 3134 Australia. Also located at 47 Stonedon Drive, East Tamaki, Auckland 2013 New Zealand. Visit www.acmptyltd.com.

Customer Support & Enquiries

Australia

Email: info@wastemaster.net.au

Tel: 1300 490 922

Website: www.wastemaster.net.au

New Zealand

Email: info@wastemaster.co.nz

Tel: 0800 744 794

Website: www.wastemaster.co.nz

Item Number: VAP01

Made in: China

Warranty

5 Year Warranty