File Info : application/pdf, 11 Pages, 2.23MB

JavaScript is disabled. Open the PDF or Download.

qtm-eleddmx-master-ordering-guide-set ?d=1025202192012

QTM-eLED+DMX LED POWER SUPPLY 100W300W
QTM-eLED+DMX is an LED power supply for DMX applications. It utilizes a 100W constant voltage LED Driver from Thomas Research and the LINEARdrive DMX decoder from eldoLED. The unit is available in 100-300 watt capacity. The power supplies and decoders are all prewired together along with terminal blocks for power and control wires. The housing can be recessed or surface mounted.

Part Number Builder
Product QTM-eLED

Size1
100W 200W 300W

Prim. V UNV

Sec. V 24VDC

Control DMX

Color2
WH (Standard) BK

Technical Information

1 Size
Size 100W 200W 300W

Max Load (Watts) 1x100W 2x100W 3x100W

Secondary Voltage
(12/24VDC)
24VDC
24VDC
24VDC

Max Prim Amps @ 120V 0.95A 1.90A 2.85A

Max Prim Amps @ 277V 0.40A 0.80A 1.20A

2 Color
WH White (Standard) BK Black Powder Coat Finish

Voltage Drop Chart

VDC

Watts (W)

10 AWG (5.6mm2)

12 AWG (3.3mm2)

14 AWG (3.0mm2)

16 AWG (1.3mm2)

18 AWG (0.78mm2)

20 AWG (0.50mm2)

22 AWG (0.33mm2)

897'

564'

355'

223'

140'

88'

55'

567'

356'

224'

141'

88'

56'

35'

309'

194'

122'

77'

48'

30'

130'

82'

51'

32'

20'

13'

100

84'

53'

33'

21'

13'

*Distances are based on a 5% Voltage drop max. · This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved

24 AWG (0.22mm2)
35' 22' 12' 5' 3'

26 AWG (0.13mm2)
22' 14' 7' 3'

COMPLIANT
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | sales@q-tran.com | www.q-tran.com

Specification subject to change. Rev-07-26-22

SECONDARY

R G B W+24 R G B W+24 R G B W+24

LED DRIVER A LED DRIVER B LED DRIVER C (120V - 277V) (120V - 277V) (120V - 277V)

QTM-eLED+DMX LED POWER SUPPLY 100W300W

BOTTOM TRAY

14.5"
GND HOT NEU

DMX IN

DMX OUT

PRIMARY

8.00"

TOP TRAY

M -+

.875"

M -+

BOTTOM

9 Knockouts of 0.875" Hole

M -+

for 1/2" fitting

NOTE: 16 additional side knockouts

4.00"

Housing
· 18 gauge welded steel enclosure: 14.5"W x 8.00"H x 4.00"D
· Door: 15.5"W x 9.00"H
· Knockouts: 25
· Built-in support bracket incorporated to secure housing for surface mounting
Performance
· Power Supply : Rated for surface mount or recessed use : Fully rated to operate low voltage load at listed wattage (No derating required) : Voltage regulation to 2% or less of rated output voltage : The ability to be dimmed using DMX dimming : Universal input range of 120-277 Vrms
· Low Voltage Lighting Systems : CSA Class 3425-15 and Class 3425-95 : Short circuit protection (SCP) : Over voltage protection (OVP) : Over current protection (OCP) : Live tested by the manufacture to ensure proper operation : Manufacturer offers a minimum of 5 years warranty

· Terminal blocks is made of tin plated copper with a voltage rating of 300V and a current rating of 40A

· Limited output voltage and current, plus isolation for safe operation
· Controllable with DMX decoder module · DMX dimming down to 0.1% · Fully potted driver(s) for moisture resistance · Suitable for dry and damp locations · Suitable for surface or recessed mounting use · Primary voltage - universal (120-277V) · Wide operating temperature range: -4°F to 122°F · Fits up to (3):100W 24 VDC driver(s) and DMX decoder
module(s)

· 5 years warranty · Driver has Class A sound rating · Class 2 output · CSA #239924
Low Voltage Lighting Systems : CSA class 3425-15 and class 3425-95 : CSA standard C22.2 No. 250.0-08 - Luminaires : ANSI/ UL standard2108 - Low voltage lighting systems : CSA standard C22.2 No 250.13-14 - Light emitting diode (LED) equipment for lighting applications : ANSI/ UL standard8750 - Light emitting diode (LED) equipment for use in lighting products

COMPLIANT
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | sales@q-tran.com | www.q-tran.com

Specification subject to change. Rev-07-26-22

QTM-eLED+DMX LED POWER SUPPLY 100W300W

Specifications (per 100W circuit)

Input Input Voltage (Vrms) Input Current, max (Arms) Inrush Current, max* (Apk) Input Frequency (Hz) Input Power (W)

24VDC

120

230

277

0.98

0.51

0.43

---

50/60

117

Output

RGB

Output Voltage, nom (V)

Output Current (A) per channel

1.4

Output Power (Wmax)

100

Output Power (Wmax) per channel

RGBW 24 1.0 100 60

Environmental THD (%) PF (%) Case Temp (ºC) *- 200us event

Min

Nom

Max

---

0.90

---

Life Time (kHrs)

Protections
· Short Circuit Protection (SCP) · Over Voltage Protection (OVP) · Over Current Protection (OCP) · Class 2 Output
Compliance
· EMI Spec : FCC 47 Part 15 : EN61000-3-2
· CSA Certified : UL-2108 : UL-8750 : CSA C22.2 No 250.0-08 : CSA C22.2 No 250.13-14
Life Time vs. Case Temperature
120 100
80 60 40 20 0
25 30 35 40 45 50 55 60 65 70 75 80 85 90 Case Temperature (ºC)

Efficiency (%)

Efficiency, 24VDC

120Vrms 277Vrms

100 90

100

% Rated Load

Output Voltage (V)

Vout vs. Iout, 24VDC

24.2

24.1

23.9

23.8

23.7

23.6

23.5

23.4

0.5

1.5

2.5

120Vrms

3.5

Output Current (A)

277Vrms

4.5

COMPLIANT
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | sales@q-tran.com | www.q-tran.com

Specification subject to change. Rev-07-26-22

QTM-eLED+DMX LED POWER SUPPLY 100W300W

Wiring Diagram
Ext in + Ext in -
DMX in + DMX in DMX in shield LedSync thru + LedSync thru LedSync shield

{

12 -28VDC IN -+

VDC and LED connectors:

AWG 24-16

0.2-1.5 mm2

0.35 inch

Other connectors:
AWG 20-16 0.5-1.5 mm2
0.35 inch

Max | Vdc+ 32V | Vdc-

DMX in + DMX in DMX in shield LedSync thru + LedSync thru LedSync shield

LINEARdrive 180D
12-28V / 6A Direct voltage controlled LED driver
M

TC
LED supply + Group 1 Group 2 Group 3 Group 4

Ext in Ext in +
LED groups

RG B W RR R R

12V - 28V DC IN
· To connect the driver to a DC power supply unit (PSU), connect the PSU's positive voltage supply wire to the VDC+ connector and the PSU's negative voltage supply wire to the VDC- connector.
EXT in
· You have the possibility to connect an external control device (0-10V control device, 10k potentiometer or show selection switch) to the driver's Ext in+ and Ext in - connector. Configure the driver for use with an external control device over the 3 button user interface.
DMX in/LedSync out
· Use these connectors when the driver is used in a DMX network. For DMX in, connect the network cable's DMX+, DMXand DMX shielding wire (the orange/white, orange and brown wire in a CAT5 cable) to the DMX in+, DMX in- and DMX in shield connector respectively. For LedSync out, connect the network cable's DMX+, DMX- and DMX shielding wire to the LedSync out+, LedSync out- and LedSync shield connector respectively. DMX Shield must be grounded to Earth ground at a single point external to power supply
LED groups
· Indicates the location of the connectors for your LED groups. R(ed) represents channel 1, G(reen) represents channel 2, B(lue) represents channel 3 and W(hite) represents channel 4. The default group color allocation can be changed over the 3-button user interface.

COMPLIANT
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | sales@q-tran.com | www.q-tran.com

Specification subject to change. Rev-07-26-22

INSTALLATION LED POWER SUPPLY - QTM-eLED+DMX
· Must be installed by licensed electrician. · Installation must be in accordance with DMX512-A standard · DMX Shield must be grounded to Earth Ground at a single point external to power supply

COMPLIANT

LOW VOLTAGE LIGHTING SYSTEM
CLASS: 3425-15 3425-95

· Wear rubber shoes and work on a sturdy wooden or fiberglass ladder.
· This power supply must be installed according to the National Electric
· Code and local codes and ordinances.
· This power supply is to be installed and serviced only by an licensed electricians.
· This power supply is to be installed so that it is not likely to be contacted by people.
· To avoid a hazard to children, account for all parts and destroy all packaging materials.
· Do not install in wet locations.

Specification subject to change. Rev-12-08-21

4.00" 9.5" O.C.

More Units can be stacked 9.5" O.C.
14.5"

INSTALLATION LED POWER SUPPLY - QTM-eLED+DMX
Housing

8.00"

4.00"

ISOMETRIC VIEW

Mounting Options

8.00" BOTTOM VIEW

0.875" KNOCKOUT 9X (FOR 1/2" FITTINGS)

1/4" Rod Thru Hole
3/8" Rod Thru Hole
Double Sided Key Hole

NOTE: Bracket can also be mounted (Top & Bottom) for Vertical Mounts.

RECESSED

SURFACE

HORIZONTAL
SURFACE SPACING 9.5" O.C.

VERTICAL 19" O.C.

More Units can be stacked

RECESSED MOUNT
16" O.C. More Units can be stacked

R(OHDorSizUoSnPtaElN) SION

R(OVDerStiUcaSlP) ENSION

SURFACE STACKING

ROD SUSPENSION
Vertical

Plenum Door Required Horizontal

NOTE: Rods not included.

Specification subject to change. Rev-12-08-21

INSTALLATION LED POWER SUPPLY - QTM-eLED+DMX
Connecting and Configuring the LINEARdrive 100D/180D

M -+

M -+
-+

LED DRIVER 2 (120 - 277V)

To DMX Controller

DMX in shield

LedSync shield

DMX in + DMX in DMX in shield LedSync thru + LedSync thru LedSync shield

DMX in -

LedSync thyu -

Ext in Ext in +

Ext in -

DMX in +

LedSync thyu +

Ext in +

White = White Blue = Blue Green = Green Red = Red Black = +24V

GND HOT NEU GND HOT NEU
iQ-LED

R G B W+24
iQ-LED
Blue Wire = Blue LED Red Wire = Red LED Green Wire= Green LED White Wire = White LED Black Wire = +24V
DMX Shield DMX DMX + SECONDARY PRIMARY

C
DMXIN DMXOUT

R G B W+24 DMXIN DMXOUT

DMX in + DMX in DMX Shield LedSync thru + LedSync thru LedSync Shield

NEU HOT GND

LED DRIVER (120 - 277V)
GND HOT NEU

DMX in + DMX in DMX in shield LedSync thru + LedSync thru LedSync shield

LINEARdrive 180D
12-28V / 6A Direct voltage controlled LED driver

Primary Wiring
GND HOT NEU

LED DRIVER (120 - 277V)

Secondary Wiring

e 180D

TC
LED supply + Group 1 Group 2 Group 3 Group 4

Black Wire = +24V Red Wire = Red LED Green Wire = Green LED Blue Wire = Blue LED
- + WMhite Wire = White LED

iQ-LED
R G B W+24 iQ-LED

Commonly Asked Questions

1) How can I verify my installation?

· Apply AC input, verify display turns on : This confirms AC input wiring

· Run "Visual Test Run" : This verifies wiring of LEDs. Make sure LEDs turning on go in same order as the Test Run

GND

2) I don't have a controller yet, how can I keep my lights on?

· Change the Mode to "COLOR" : This allows to manually set a specific color to be on

HOT

· Adjust the Hue or WHITE to achieve the desired color : This sets that specific color

NEU

3) My LEDs aren't coming out the right color. They look like white has been added in

· Verify the Network Resolution "NETW RES" : Default is 8 BT

· Check your DMX Programming. Stick controllers come with RGB programs by default. This will cause RGBW

LEDs to show Pink vs. Red

Control Wiring
DMX Connections

Ext in Ext in +

DMX

LedSync shield LedSync thru LedSync thru + DMX in shield
DMX in DMX in +

DMX in shield DMX in DMX in +

WARNING: Risk of electrical shock. May result in serious injury or death. Disconnect power before servicing or installing.
CAUTION: The device may only be connected and installed by a qualified electrician. All applicable regulations, legislation and building codes must be observed. Incorrect installation of the device can cause irreparable damage to the device and the connected LEDs.
DMX Shield must be grounded to Earth Ground at a single point external to power supply

Specification subject to change. Rev-12-08-21

INSTALLATION LED POWER SUPPLY - QTM-eLED+DMX

Manual Configuration

1. Select mode of operation:

+ /-

M (5 sec)

Set mode
SET MODE M
display off

COLR SHOW DMX

3. Standalone operation - Colour*-

Standalone

operation

- Show -

Networked operation
- DMX -

HUE
HUE
M

+ /-

0...1535

Show
SHOW
M

00...20

+ /-

DMX address
DMX ADDR
M

1...512

White
WHIT
M
Intensity
INT M
display off

0...255 0...255

+ /-

Speed
SPD
M
Intensity
INT
M
display off

-99...99 0...255

+ /-

Network resolution
NETW RES
M

8 BT 16 BT

Interpolation
INTERPOL
M
display off

OFF VID COLR WHIT GLOW

* The colour menu depends on the LED group settings you have selected in step 2.

+ /+ /+ /+ /+ /-
+ /-
+

2. Set LED groups:

M+

LED groups
LED
M
External input
EXT INP M
Dimming curve
DIM CURV M

1-1L RGB 2-2L RGBW 3-3L RGBA 4-4L RRGB 2-4L RGGB 1-4L CCWW
CWWW
OFF POTM 10V SWIT
LOG LIN

display off

Other Features

Visual test run

M+

Test
TEST
R 1 sec G 1 sec B 1 sec W 1 sec RGBW 1 sec R 1 sec G 1 sec B 1 sec W 1 sec RGBW 1 sec
display off

Locking the configuration:

+ /-
+

M+

(5 sec)

Lock driver
LOCK
M

NO SOFT HARD

display off

Reset to factory defaults

M+

(5 sec)

Reset
RE - SET PRES MENU
Press menu
M
display off

Specification subject to change. Rev-12-08-21

M -+ M -+ M -+
M -+

INSTALLATION LED POWER SUPPLY - QTM-eLED+DMX

Wiring Installation
QTM-eLED+DMX : for interior

LED DRIVER 2 (120 - 277V)

White = White Blue = Blue Green = Green Red = Red Black = +24V

LED

R G B W +24V

LED

DMX Shield

DMX -

DMX + SECONDARY PRIMARY
Blue Wire = Blue LED Red Wire = Red LED Green Wire = Green LED White Wire = White LED Black Wire = +24V

DMX IN

DMX OUT To next power supply

R G B W+24 R G B W+24 R G B W+24

GND HOT NEU

Red Blue Green

GND HOT NEU
DMX + DMX GND

LED

Specification subject to change. Rev-12-08-21

INSTALLATION LED POWER SUPPLY - QTM-eLED+DMX
CSA Requirements
· Suitable for indoor use · This power supply must be installed according to the National Electric Code and local codes and ordinances and in
accordance with applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. · Wear rubber shoes and work on a sturdy wooden or fiberglass ladder. · This power supply is to be installed in a location where it is not likely to be contacted by non-electricians. · To avoid a hazard to children, account for all parts and destroy all packaging materials. · DMX shield wire must be grounded to earth ground at a single point external to power supply.

QTM-eLED

Model
QTM-eLED-60 QTM-eLED-120 QTM-eLED-180 QTM-eLED-100 QTM-eLED-200 QTM-eLED-300

Input Voltage (V)
120-277 120-277 120-277 120-277 120-277 120-277

INPUT VOLTAGE OUTPUT VOLTAGE CONTROL TYPE

120V-277

12V

24V

Input Current (A)
0.60/0.29 1.20/0.58 1.80/0.87 0.95/0.40 1.90/0.80 2.85/1.20

Frequency Nominal Output Nominal Output Voltage (VDC) Wattage (W)

50/60

120

50/60

180

50/60

100

50/60

200

50/60

300

0-10V DMX WD AW

Type Ic Recessed, Inherently Protected
Type IC ENCASTRE, PROTECTION INHÉRENTE
For Supply Connections Use Wire Rated For At Least 60 C.
Not for use with dimmers
NE CONVIENT PAS A DES GRADATEURS
Suitable For Damp Locations
CONVIENT AUX EMPLACEMENTS HUMIDES
50/60 Cycle Class 1 or Class 2

This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D'INSTALLATION PERTINENT, PAR UNE PERSONNE QUI CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS.

LOW VOLTAGE LIGHTING SYSTEM
Q-Tran, Inc. CLASS: 3425 - 15
3425 - 95

Q-TRAN, INC. MILFORD, CT U.S.A.
(203) 367-8777 WWW.Q-TRAN.COM

Specification subject to change. Rev-12-08-21

MATERIAL RECYCLING
QTM/QOM-eLED
You may be done with your products, but chances are they still have more to give. Follow these instructions to break down and sort recyclable components. Check with local recycling collection to ensure they accept the materials listed below.
Additionally, Q-Tran offers a Takeback Program. Contact factory for information.

Housing Base Plate

LED DRIVER 1 (120V - 277V)

LED DRIVER 2 (120V - 277V)

LED DRIVER 3 (120V - 277V)

0 - 10V DIM-MOD 1

0 - 10V DIM-MOD 2

0 - 10V DIM-MOD 3

LED Drivers Dimming Modules

Wires Dimming Module Plate

Output Load Output Load Output Load Dimmer control

NEU HOT GND Input Load

QTM-eLED shown

Terminal Blocks Divider Plate

7
Terminal Blocks

E
LED Drivers Dimming Modules
Wires

40
Housing Base Plate Dimming Module Plate Divider Plate

Specification subject to change. Rev-10-24-22