Parameters Built-in battery: 500mAh, 3.7V Li-Po battery Operating
RX4 四合一多协议高频头 RX4 4-IN-1 MULTI-PROTOCOL RF MODULE CC2500 CYRF6936 A7105 NRF24L01 protocols table / 默认协议列表: Dial 开关档位
iRangeX R4X Pro 2a4G CC2500 NRF24L01 A7105 CTRF6936 4IN1 Multiprotocol External TX Module w/Battery Sale - RC Toys & Hobbies English Manual,
RX4 RX4 4-IN-1 MULTI-PROTOCOL RF MODULE CC2500 A7105 CYRF6936 NRF24L01+ Dial 0 1 2 3 4 5 6 7 8 9 A B C D E F Default protocols table / : Protocol Sub_protocol Auto Bind Option Reserved - FLYSKY FLYSKY No/ 0 HUBSAN - Yes/ 0 AFHDS2A PPM_SBUS No/ -10 FRSKYD - No/ 0 FRSKYX CH_8 No/ 0 S-FHSS - Yes/ 10 DSM2 DSM2_22 No/ 6 DEVO - No/ 0 J6PRO No/ 0 ESKY No/ 0 HISKY Hisky No/ 0 KN WLTOYS No/ 0 V2X2 V2X2 No/ 0 MJXQ E010 Yes/ 0 ASSAN - No/ 0 RF Chip A7105 A7105 A7105 CC2500 CC2500 CC2500 CYRF6936 CYRF6936 CYRF6936 NRF24L01+ NRF24L01+ NRF24L01+ NRF24L01+ NRF24L01+ NRF24L01+ Parameters Built-in battery: 500mAh, 3.7V Li-Po battery Operating time: 5-12 hours, depends on protocol RF power: +22dBm Size: 59x37x21mm, antenna not include Operating current: <=100mA Operating frequency: 2.4G ISM band Material of Case: Aluminum alloy CNC Weight: 68g Normal use operation: 1. Screw down the antenna of module tightly. Turn on you transmitter and set PPM signal output. 2. Connect the 3.5mm plug of signal cable to the DSC (or trainer) port of your transmitter, and connect the 2.5mm plug to PPM port of RF module. 3. According to Protocols table, turn protocol switch of RF module to choose the proper protocol. 4. After finish binding operation, power on your transmitter and RF module, the status indicator will turn greenafter that turn on your receiver (or craft) , then RF module is ready to work , 5. There is a buzzer in RF module, it will beep when the battery is low (below 3.5V). Please land your craft as soon as possible while beeping, and then turn off RF module. Binding operation: 1. Power on your receiver, and set it to binding mode. 2. Hold and press the bind button of RF module, and then turn on it, after 2 seconds, release the button, you will see the green light flashing rapidly, then RF module is in binding mode, and the green light will go solid after binding. 3. Some protocols (eg: S-FHSS) don't have binding procedure on RF module, and some protocols (eg: hubsan, e010)will auto bind when power up. Charging operation: 1. Turn the protocol switch to"0", power off RF module, then connect RF module to an USB charger (or other USB power supply) using Micro USB wire (not include), the status indicator will turn red while charging, and the red light will be off when charging is done. 2. RF module will always work when connect to USB power, no matter the power switch is on or off, but battery will be charged only when power switch is off. About protocols: This module is based on ATmega328P, There are 15 different protocols mapping To the 16-position protocol selection switch on the module. They are listed in the default protocols table on the last page, and You can customize these when you compile you own firmware. For more information, You can scan the QR code to access : Notice: 1. We only provide an audio cable, in addition, some transmitters (eg: Futaba,Wfly) need a trainer cable(standard accessories of transmitter) to connect RF module. 2. Built-in battery has protection logic, it will cut off the battery when voltage is below 3.0V, and the buzzer may stop working when voltage is below 3.3V. : 500mAh3.7V Li-Po : 5-12 : +22dBm : 59x37x21mm : <=100mA : 2.4G ISM : CNC : 68g : 1. PPM 2. 3.5mm DSC 2.5mm PPM 3. 4. "ON" 5. 3.5 : 1. 2. 3. S-FHSS Hubsan,E010 . : 1. "0""OFF" Micro USB USB USB 2. USB "OFF" : ATmega328P 15 16 "0" . : : 1. 2.5mm 3.5mm Futabat, 2. 3.0 3.3福昕PDF打印机 版本 7.3.4.0308