Assembly Instruction

Part List

Hardware List

Assembly Steps

STEP 1 (ÉTAPE 1)

Parts used: Part 2 (Side board Right), Part 3 (Side board Left)

Hardware used: Not specified in this step's visual, but implied by the 'Lx2' icon.

Attach Part 2 and Part 3. The diagram shows two circular elements labeled 'L' being inserted, with a 'Lx2' icon indicating quantity. A circular arrow indicates rotation or tightening, with '100%' suggesting full tightening. The 'X2' icon indicates this action is performed twice.

STEP 2 (ÉTAPE 2)

Parts used: Part 3 (Side board Left)

Hardware used: Not specified in this step's visual, but implied by the 'Lx2' icon.

Attach Part 3. The diagram shows two circular elements labeled 'L' being inserted into Part 3. A circular arrow indicates rotation or tightening, with '100%' suggesting full tightening. The 'X2' icon indicates this action is performed twice.

STEP 3 (ÉTAPE 3)

Parts used: Part 2 (Side board Right)

Hardware used: A x 4, B x 4, C x 4, D x 1

Attach hardware to Part 2. The diagram shows a close-up view of connection points on Part 2. It indicates using 4x Bolt A, 4x Washer B, 4x Washer C, and 1x Allen Key D. The 'X4' icon indicates this assembly is done four times. A circular arrow with '80%' suggests partial tightening.

STEP 4 (ÉTAPE 4)

Parts used: Part 3 (Side board Left)

Hardware used: A x 4, B x 4, C x 4, D x 1

Attach hardware to Part 3. The diagram shows a close-up view of connection points on Part 3. It indicates using 4x Bolt A, 4x Washer B, 4x Washer C, and 1x Allen Key D. The 'X4' icon indicates this assembly is done four times. A circular arrow with '80%' suggests partial tightening.

STEP 5 (ÉTAPE 5)

Parts used: Part 2 (Side board Right), Part 3 (Side board Left), Part 4 (Back Rails), Part 5 (Front Rails)

Hardware used: Not explicitly listed, but implied by connection points.

Connect Part 4 (Back Rails) and Part 5 (Front Rails) to Part 2 and Part 3. The diagram shows the main frame coming together, with red circles indicating connection points. A close-up shows hardware being used, though not detailed here.

STEP 6 (ÉTAPE 6)

Parts used: Assembled frame from previous steps.

Hardware used: Not specified, but implies tightening of previously installed bolts.

Tighten all screw bolts to 100%. The diagram shows a circular arrow with '100%' and text "TIGHTEN ALL SCREW BOLTS 100% / SERREZ TOUS LES BOULONS À 100%". It also shows the Allen key (D) and a bolt.

STEP 7 (ÉTAPE 7)

Parts used: Part 1 (Head board), Part 2 (Side board Right), Part 3 (Side board Left), Part 4 (Back Rails), Part 5 (Front Rails)

Hardware used: K x 4, B x 4, C x 4, D x 1

Attach Part 1 (Head board) to the assembled frame. The diagram shows connection points on Part 1 and the frame. It indicates using 4x Bolt K, 4x Washer B, 4x Washer C, and 1x Allen Key D. The 'X4' icon indicates this is done four times. A close-up shows the hardware assembly. A circular arrow with '100%' suggests full tightening.

STEP 8 (ÉTAPE 8)

Parts used: Part 1 (Head board), Part 2 (Side board Right), Part 3 (Side board Left), Part 5 (Front Rails), Part 6 (Bed side brace Right)

Hardware used: E x 3, B x 3, C x 3, D x 1

Attach Part 6 (Bed side brace Right) to the frame. The diagram shows connection points on Part 6 and the frame. It indicates using 3x Bolt E, 3x Washer B, 3x Washer C, and 1x Allen Key D. The 'X3' icon indicates this is done three times. A close-up shows the hardware assembly. A circular arrow with '100%' suggests full tightening.

STEP 9 (ÉTAPE 9)

Parts used: Part 1 (Head board), Part 2 (Side board Right), Part 3 (Side board Left), Part 4 (Back Rails), Part 5 (Front Rails), Part 7 (Bed side brace Left)

Hardware used: E x 3, B x 3, C x 3, D x 1

Attach Part 7 (Bed side brace Left) to the frame. The diagram shows connection points on Part 7 and the frame. It indicates using 3x Bolt E, 3x Washer B, 3x Washer C, and 1x Allen Key D. The 'X3' icon indicates this is done three times. A close-up shows the hardware assembly. A circular arrow with '100%' suggests full tightening.

STEP 10 (ÉTAPE 10)

Parts used: Part 8 (Bed support Slates), Part 9 (Slates Right), Part 10 (Slates Left), Part 11 (Slates)

Hardware used: F x 20, H x 20, I x 20, D x 1

Assemble the bed slats. The diagram shows multiple slats (Part 11) being attached to support rails (Part 8, 9, 10). It indicates using 20x Bolt F, 20x Washer H, 20x Washer I, and 1x Allen Key D. The 'X20' icon indicates this is done twenty times. A close-up shows the hardware assembly. A circular arrow with '100%' suggests full tightening.

STEP 11 (ÉTAPE 11)

Parts used: Part 8 (Bed support Slates), Part 9 (Slates Right), Part 10 (Slates Left), Part 11 (Slates), Part 12 (Lift truck Right), Part 13 (Lift truck Left)

Hardware used: G x 6, H x 6, I x 6, D x 1

Attach the lift mechanisms (Part 12 and 13) to the bed frame and slats. The diagram shows connection points. It indicates using 6x Bolt G, 6x Washer H, 6x Washer I, and 1x Allen Key D. The 'X6' icon indicates this is done six times. A close-up shows the hardware assembly. A circular arrow with '100%' suggests full tightening.

STEP 12 (ÉTAPE 12)

Parts used: Part 1 (Head board), Part 2 (Side board Right), Part 3 (Side board Left), Part 4 (Back Rails), Part 5 (Front Rails)

Hardware used: G x 4, H x 4, I x 4, D x 1

Final assembly and checks. The diagram shows the assembled bed frame and indicates final connections. It indicates using 4x Bolt G, 4x Washer H, 4x Washer I, and 1x Allen Key D. The 'X4' icon indicates this is done four times. A close-up shows the hardware assembly. A circular arrow with '100%' suggests full tightening.