HyperTough Keyless Electronic Deadbolt Installation and Programming

1) Installation Overview

Package Includes:

• Exterior Faceplate (1)
• Interior Faceplate (1)
• Latch (1)
• Strike Plate (1)
• Mounting Plate (1)
• Set Screw (1)
• Mounting Post (2)
• 2-7/8" Screws (2)
• 2-5/16" Screws (4)
• 1-3/4" Screws (4)
• 1" Screw (1)
• User Guide (1)
• Keys (2)

Tools Needed for Door Preparation (if there is no knob hole): Drill, 2 1/8" Hole Saw, 1" Hole Saw, 3/4" Chisel

Preparation: Refer to the included template for door preparation instructions.

Strike Plate Installation: Ensure the strike plate on the door frame is straight and not protruding. Adjust as needed for smooth bolt fitting.

2) Install Enclosed Latch and Strike Plate

Note: Do not over-tighten latch screws.

Backset Adjustment (2-3/8" to 2-3/4"):

1. Hold latch with numbers facing forward and thumb pressing on the bolt.
2. Rotate the cylinder cover clockwise.
3. Pull and twist the extension plate all the way out.
4. Rotate the cylinder counter-clockwise so the marking aligns with the 2-3/4" position indicator.

Ensure the latch plate on the door is straight and not protruding. Adjust before installing to prevent issues with the bolt fitting into the latch hole.

3) Install Exterior Assembly

Note: Check that the Rubber Gasket is secured on the Exterior Assembly.

Insert the Exterior Assembly onto the door with the tailpiece going through the Deadbolt Latch Set in the VERTICAL POSITION. Route the Control Wire through the door UNDER the Deadbolt Latch Set.

Testing: With the door shut, lock and unlock using the key. Ensure the latch operates smoothly and is aligned properly without scraping the strike plate. If not, revisit step 2.

Deadbolt Latch Must Be Retracted During Installation.

4) Install Interior Assembly

Preparation for Interior Assembly: Remove one screw (K) from the inside of the battery compartment within the housing (B) to release the Mounting Plate (C).

Screw Mounting Post (L) into holes on Mounting Plate (C). Screw (K) can be used optionally to prevent the lock from shifting.

Assembly: Carefully insert the control wire into the wire connector. Ensure the connector dots align with the dots on the wire.

5) Install Interior Assembly

Note: Make sure the Knob is in the vertical position. Be careful not to pinch the control wire.

Secure the mounting plate to the door. Carefully insert the control wire into the wire connector.

6) Install Batteries and Cover

Open the door before inserting high-quality AA alkaline batteries. The lock is set for a right-handed door and will automatically determine if your door is left-handed.

The lock motor will engage and perform a series of locking and unlocking motions. The keypad will beep and lights will flash upon completion.

Note: Do not touch the keypad until the light turns off. Do not use rechargeable or mixed old/new batteries.

Low Battery Warning: Beeps and LED flashes red 7 times. Replace with good quality alkaline batteries.

7) Testing Operation

Test the lock button with the door open.

Shut the door and test the latch alignment. Turn the thumb turn to lock and unlock, ensuring smooth operation and proper alignment with the strike plate. If issues arise, revisit step 2.

Test unlocking by pressing '1-2-3-4-' (default admin code) and then the lock button.

Congratulations! You have installed the Keyless Electronic Deadbolt with Keypad.

1) Create Administrator Code

Wake lock, input Admin Code (factory setting: 123456), press Lock/Clear button, input new 6-digit code, press Lock/Clear, repeat new 6-digit code, press Lock/Clear. Green light flashes confirming success.

2) Add User Codes

Wake lock, input Admin Code, press Lock/Clear, press '1', input User Number (02-50), press Lock/Clear, input new 4-8 digit User Code, press Lock/Clear, repeat new 4-8 digit User Code, press Lock/Clear. Green light flashes confirming success.

Programming Record: Fill in your Administrator Code and User Codes (02-50) with their creation dates.

3) Unlock Door with User Code

Wake lock, input User Code, press Lock/Clear.

4) Delete a User Code

Wake lock, input Admin Code, press Lock/Clear, press '2', input User Number to delete, press Lock/Clear, repeat User Number, press Lock/Clear. Green light flashes confirming success.

5) Delete All User Codes

Wake lock, input Admin Code, press Lock/Clear, press '3', press Lock/Clear, re-enter Admin Code, press Lock/Clear. Green light flashes confirming success.

6) Additional Programming Functions: Automatic Lock Function

Set Auto Lock: Enter AC5, then the Time Value (20-900 seconds). Hear 1 beep and light illuminates green.

Cancel Auto Lock: Enter AC5-00-. Hear 1 beep and light illuminates green.

Temporarily Disable Auto-Lock: Unlock with AC, immediately turn the locking knob by hand to locked, wait 3 seconds, then turn back to unlock. Auto-Lock is now disabled.

Restore Auto-Lock: Turn locking knob to locked position, wait 3 seconds, or press the Lock button on the keypad.

7) Additional Programming Functions: Sound On and Off

Sound Off: Enter AC61. Light Indicator illuminates green.

Sound On: Enter AC62. Hear 1 beep and light illuminates green.

Restore Factory Settings

1. Remove one battery for 10 seconds.
2. Reinsert battery, wait for long and short beep.
3. Press Lock/Clear button 3 times within 3 seconds.
4. Lock will beep and light indicator will turn green.

Note: Removing batteries does not erase active Administrator or User Codes.

Helpful Tips

• Interior Knob will not turn or has tension: Knob or vertical tailpiece is installed incorrectly. Reposition the interior knob and ensure the tailpiece is vertical with the deadbolt latch retracted.
• Lock will not function electronically: Check batteries (high-quality alkaline, proper polarity), control wire connection and integrity, and ensure wires are not loose.
• Lock gives error signal or latch does not extend/retract completely: Ensure strike plate alignment is correct. Check that the tailpiece is vertical. Installation screws may be too tight; loosen mounting plate screws slightly.
• Deadbolt Latch is sticking: Readjust latch for smoother operation.
• Keypad not working: Press any key to wake the lock before programming. Ensure programming steps are completed within 5 seconds.
• Low Battery Warning: Beeps and LED flashes red 7 times. Replace with 4 high-quality alkaline batteries.
• Secure Lock-out period: Warning sounds and LED flashes red after 4 incorrect code attempts; keypad shuts down for 60 seconds. Wait 60 seconds.
• Vacation Mode: With Vacation Mode enabled (AC1 -> 0 -> 1 -> 2), all buttons and functions are disabled. To disable, press and hold Lock/Clear for 4 seconds, then input AC and Lock/Clear.