SLBK5KBGG by Flash Furniture - Roxbury King Size Tufted Upholstered Platform Bed in Beige Fabric | Southern Accents Home Town Furniture and Appliances
Adult Assembly Required. DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE. Serious or fatal injuries can occur from furniture tipping over. You must install Tipping ...
Thank you for your purchase! PLATFORM BED FRAME 500 LBS TWIN SIZE 400 LBS 400 LBS FULL SIZE 600 LBS 600 LBS QUEEN SIZE 900 LBS 900 LBS KING SIZE ASSEMBLY INSTRUCTIONS Before You Begin: Please indentify all component parts and hardware pieces required before you begin. Carefully remove all of the components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching during assembly. Caution: Tighten all components securely before use. Failure to do so may result in personal injury. DO NOT use any sharp objects to open plastic wrapped components as damage to product or components may result. Warning: CHOKING HAZARD - Small Parts. Adult Assembly Required. DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware (where included) to help prevent the unit from tipping and causing accidental injury, instability, death or damage. The tipping restraint is intended only as a safety measure, it is not a substitute for proper adult supervision. To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed. ................................................................................................................................................................ Customer Service Email: CustomerExperience@belnick.com | Phone: 866-552-2810 SL-BK5-T-B-GG / SL-BK5-T-BK-GG / SL-BK5-T-DG-GG / SL-BK5-T-LG-GG / SL-BK5-F-B-GG / SL-BK5-F-BK-GG SL-BK5-F-DG-GG / SL-BK5-F-LG-GG / SL-BK5-Q-B-GG / SL-BK5-Q-BK-GG / SL-BK5-Q-DG-GG / SL-BK5-Q-LG-GG SL-BK5-K-B-GG / SL-BK5-K-BK-GG / SL-BK5-K-DG-GG / SL-BK5-K-LG-GG Have a Question/Concern? Quality products and first-class customer service are the cornerstone of long-lasting consumer relationships. We strive toward excellence in all we do and want you to be completely satisfied with your purchase. Please contact our exceptional Customer Experience Agents at the email address or phone number shown below to assist you with any product questions or issues before requesting a return. We look forward to serving you in a friendly, efficient manner to resolve any issues you may have. Customer Service Email: CustomerExperience@belnick.com Customer Service Phone: 866-552-2810 For warranty information, please visit www.belnick.com A Headboard C Headboard Middle Leg PLATFORM BED FRAME INSTRUCTION E Siderails Components G Middle Cross Beam I Middle Brace Feet K Bed Legs M Screw f8*40 O Outer Slat Holders 1pc 1pc 4pcs 2pcs 2pcs 2pcs 11pcs 28pcs B Headboard Side Legs D Footboard F Middle Brace H Middle Leg J Slats L Washer f8 N Allen Wrench P Middle Slat Holders 2pcs 1pc 1 STEP 1: Attach Headboard Side Legs (Part B) and Headboard Middle Leg (Part C) to Headboard (Part A) using (6) Washers (Part L) and (6) 8*40 Screws (Part M). Tighten with Allen Wrench (Part N) 1pc 1pc 28pcs 11pcs 1pc 2 STEP2: Insert Bed Legs (Part K) into Footboard (Part D) and turn clockwise to tighten. D 14pcs B C A 3 STEP 3: Attach Middle Cross Beam (Part G) to Middle Leg (Part H) using (2) Washers (Part L) and (2) 8*40 Screws (Part M). Tighten with Allen Wrench (Part N) LM N L G H G K Note: Screws preassembled on the footboard 4 F K NOTE: Ensure brackets face outward with slots point up. I M STEP 4: Attach Middle Brace (Part F) to Middle Brace Feet (Part I) using (2) Washers (Part L) and (2) 8*40 Screws (Part M). Tighten with Allen Wrench (Part N) I N L 5 N M L 6 STEP 6A: Remove preassembled screws from middle leg. Attach Middle Cross Beam (Part G) to Middle Headboard Leg using preassembled screws. G I F H G STEP 5: Attach Middle Brace (Part F) to Middle I Cross Beam (Part G) using (1) Washer (Part L) and (1) 8*40 Screw (Part M). Tighten with Allen Wrench (Part N) 7 STEP 7: Remove remaining preassembled screws from Headboard Side Legs and Footboard. Attach Siderails (Part E) to Headboard and Footboard using preassembled screws. STEP 6B: Remove preassembled screws from Footboard. Attach Middle Brace to Footboard (Part D) using preassembled screws. 8 STEP 8: Loosen preassembled screws from Siderails (Part E). Insert screws into the slots of the Middle Legs then tighten screws. E E E E E E E Note: Screws preassembled on the leg E Note: Screws preassembled on the siderail 9 STEP 9: Insert (28) Slats (Part J) into the left and right sides of the Middle Slat Holders (Part P). Insert Slats into Outer Slat Holders (Part O). Push down on slat holders to secure. J 10 STEP 10: Ensure all screws and slats are secure. P O J A Headboard C Headboard Middle Leg PLATFORM BED FRAME INSTRUCTION E Siderails Components G Middle Cross Beam I Middle Brace Feet K Bed Legs M Screw f8*40 O Outer Slat Holders 1pc 1pc 4pcs 2pcs 2pcs 2pcs 11pcs 28pcs B Headboard Side Legs D Footboard F Middle Brace H Middle Leg J Slats L Washer f8 N Allen Wrench P Middle Slat Holders 2pcs 1pc 1 STEP 1: Attach Headboard Side Legs (Part B) and Headboard Middle Leg (Part C) to Headboard (Part A) using (6) Washers (Part L) and (6) 8*40 Screws (Part M). Tighten with Allen Wrench (Part N) 1pc 1pc 28pcs 11pcs 1pc 2 STEP2: Insert Bed Legs (Part K) into Footboard (Part D) and turn clockwise to tighten. D 14pcs B C A 3 STEP 3: Attach Middle Cross Beam (Part G) to Middle Leg (Part H) using (2) Washers (Part L) and (2) 8*40 Screws (Part M). Tighten with Allen Wrench (Part N) LM N L G H G K Note: Screws preassembled on the footboard 4 F K NOTE: Ensure brackets face outward with slots point up. I M STEP 4: Attach Middle Brace (Part F) to Middle Brace Feet (Part I) using (2) Washers (Part L) and (2) 8*40 Screws (Part M). Tighten with Allen Wrench (Part N) I N L 5 N M L 6 STEP 6A: Remove preassembled screws from middle leg. Attach Middle Cross Beam (Part G) to Middle Headboard Leg using preassembled screws. G I F H G STEP 5: Attach Middle Brace (Part F) to Middle I Cross Beam (Part G) using (1) Washer (Part L) and (1) 8*40 Screw (Part M). Tighten with Allen Wrench (Part N) 7 STEP 7: Remove remaining preassembled screws from Headboard Side Legs and Footboard. Attach Siderails (Part E) to Headboard and Footboard using preassembled screws. STEP 6B: Remove preassembled screws from Footboard. Attach Middle Brace to Footboard (Part D) using preassembled screws. 8 STEP 8: Loosen preassembled screws from Siderails (Part E). Insert screws into the slots of the Middle Legs then tighten screws. E E E E E E E Note: Screws preassembled on the leg E Note: Screws preassembled on the siderail 9 STEP 9: Insert (28) Slats (Part J) into the left and right sides of the Middle Slat Holders (Part P). Insert Slats into Outer Slat Holders (Part O). Push down on slat holders to secure. J 10 STEP 10: Ensure all screws and slats are secure. P O JAdobe Acrobat Pro DC (32-bit) 22.2.20191 (C) 2018 Retailer Web Services LLC, all rights reserved.