Xiamen Huoshiquan Import & Export CO., LTD HOLYSTONEIW Quadcopter 2AJ55HOLYSTONEIW 2AJ55HOLYSTONEIW holystoneiw
TEST REPORT Product Name Model Number FCC ID : quadcopter : HS440D, HS440, HS440G, HS440S, HS440R, HS440E, HS440DB, HS440DS, HS115, HS125, HS130, HS140, HS260, HS280, HS290, HS320, HS360, HS390, HS400, HS420, HS430, HS440, HS460, HS440D, HS500, HS520, HS540, HS560, HS570, HS580, HS590, HS590, HS610, HS620, HS630, HS660, HS670, HS690, HS730, HS740, HS750, HS760, HS770, HS780, HS810, HS820, HS900, HS155, HT300, HT300S, HT400, HT600, HT15, HT20, HT25, HT30, HT35, HT40, HT45, HT50, HT60, D11, D15, D22, D25, D33, D35, D23, D40, D55, D60, D65, D70, D75, D80, D90, D55, D25, D35, D45, D100 : 2AJ55HOLYSTONEIW Prepared for Address Prepared by Address : Xiamen Huoshiquan Import & Export CO., LTD : Unit 1, Room 501, Hongxiang Building, No.258 Hubin Nan Road, Siming District, Xiamen, China : EMTEK (SHENZHEN) CO., LTD. : Building 69, Majialong Industry Zone, Nanshan District, Shenzhen, Guangdong, China Tel: (0755) 26954280 Fax: (0755) 26954282 Report Number : ENS2306120066W00501R Date(s) of Tests : June 12, 2023 to July 3, 2023 Date of issue : July 3, 2023 Report No. ENS2306120066W00501R Page 1 of 41 Ver.1.0 1 TEST RESULT CERTIFICATION Applicant Address Manufacturer Address EUT Model Name Trademark : Xiamen Huoshiquan Import & Export CO., LTD : Unit 1, Room 501, Hongxiang Building, No.258 Hubin Nan Road, Siming District, Xiamen, China : Xiamen Huoshiquan Import & Export CO., LTD : Unit 1, Room 501, Hongxiang Building, No.258 Hubin Nan Road, Siming District, Xiamen, China : quadcopter HS440D, HS440, HS440G, HS440S, HS440R, HS440E, HS440DB, HS440DS, HS115, HS125, HS130, HS140, HS260, HS280, HS290, HS320, HS360, HS390, HS400, HS420, HS430, HS440, HS460, HS440D, HS500, HS520, : HS540, HS560, HS570, HS580, HS590, HS590, HS610, HS620, HS630, HS660, HS670, HS690, HS730, HS740, HS750, HS760, HS770, HS780, HS810, HS820, HS900, HS155, HT300, HT300S, HT400, HT600, HT15, HT20, HT25, HT30, HT35, HT40, HT45, HT50, HT60, D11, D15, D22, D25, D33, D35, D23, D40, D55, D60, D65, D70, D75, D80, D90, D55, D25, D35, D45, D100 : Holy Stone Measurement Procedure Used: APPLICABLE STANDARDS STANDARD FCC 47 CFR Part 2, Subpart J FCC 47 CFR Part 15, Subpart E TEST RESULT PASS The above equipment was tested by EMTEK (SHENZHEN) CO., LTD. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.10 (2013) and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements of FCC Rules Part 2 and Part 15.407 The test results of this report relate only to the tested sample identified in this report. Date of Test : June 12, 2023 to July 3, 2023 Prepared by : Reviewer : Luo peiye /Editor Joe Xia /Supervisor Approve & Authorized Signer : Lisa Wang/Manager Report No. ENS2306120066W00501R Page 2 of 41 Ver.1.0 Modified History Version Ver.1.0 Report No. ENS2306120066W00501R Revision Date / Summary Original Report Report No. ENS2306120066W00501R Page 3 of 41 Ver.1.0 TABLE OF CONTENTS 1 TEST RESULT CERTIFICATION ................................................................................................................ 2 2 EUT TECHNICAL DESCRIPTION .............................................................................................................. 5 3 SUMMARY OF TEST RESULT ..................................................................................................................... 6 4 TEST METHODOLOGY ................................................................................................................................ 7 4.1 GENERAL DESCRIPTION OF APPLIED STANDARDS ...................................................................... 7 4.2 MEASUREMENT EQUIPMENT USED .................................................................................................. 7 4.3 DESCRIPTION OF TEST MODES .......................................................................................................... 8 5 FACILITIES AND ACCREDITATIONS ....................................................................................................... 9 5.1 FACILITIES ............................................................................................................................................... 9 5.2 EQUIPMENT .............................................................................................................................................9 5.3 LABORATORY ACCREDITATIONS AND LISTINGS ...........................................................................9 6 TEST SYSTEM UNCERTAINTY ................................................................................................................ 10 7 SETUP OF EQUIPMENT UNDER TEST ....................................................................................................11 7.1 RADIO FREQUENCY TEST SETUP ..................................................................................................... 11 7.2 RADIO FREQUENCY TEST SETUP ..................................................................................................... 11 7.3 CONDUCTED EMISSION TEST SETUP ..............................................................................................13 7.4 BLOCK DIAGRAM CONFIGURATION OF TEST SYSTEM ..............................................................14 7.5 SUPPORT EQUIPMENT .........................................................................................................................14 8 TEST REQUIREMENTS .............................................................................................................................. 15 8.1 BANDWIDTH MEASUREMENT ..........................................................................................................15 8.2 MAXIMUM CONDUCTED OUTPUT POWER ....................................................................................20 8.3 MAXIMUM PEAK POWER DENSITY .................................................................................................27 8.4 UNDESIRABLE RADIATED SPURIOUS EMISSION .........................................................................31 8.5 POWER LINE CONDUCTED EMISSIONS .......................................................................................... 40 8.6 ANTENNA APPLICATION .................................................................................................................... 41 Report No. ENS2306120066W00501R Page 4 of 41 Ver.1.0 2 EUT TECHNICAL DESCRIPTION Characteristics Description Product: Model Number: quadcopter HS440D, HS440, HS440G, HS440S, HS440R, HS440E, HS440DB, HS440DS, HS115, HS125, HS130, HS140, HS260, HS280, HS290, HS320, HS360, HS390, HS400, HS420, HS430, HS440, HS460, HS440D, HS500, HS520, HS540, HS560, HS570, HS580, HS590, HS590, HS610, HS620, HS630, HS660, HS670, HS690, HS730, HS740, HS750, HS760, HS770, HS780, HS810, HS820, HS900, HS155, HT300, HT300S, HT400, HT600, HT15, HT20, HT25, HT30, HT35, HT40, HT45, HT50, HT60, D11, D15, D22, D25, D33, D35, D23, D40, D55, D60, D65, D70, D75, D80, D90, D55, D25, D35, D45, D100 (These models are identical in circuitry and electrical, mechanical and physical construction; The differences among them are model name. Only indicates for different market purposes; We chose HS440D as the final test prototype) Sample Number: 2# Wifi Type: Wifi 5G with 5180 MHz Band WLAN Supported: 802.11n(20MHz channel bandwidth) Data Rate : Modulation: 802.11n:up to 300 Mbps OFDM with BPSK/QPSK/16QAM/64QAM for 802.11n Frequency Range: TPC Function: Antenna Port: Antenna Type: Antenna Gain: 5180MHz for 802.11n(HT20); Applicable Antenna port 1 Antenna port 2 Copper Tube Antenna 2.32 dBi Not Applicable Transmit Power: 5180 MHz:13.65 dBm Power Supply : DC 7.6V from Lithium-ion Polymer Battery Date of Received: June 12, 2023 Temperature Range: Refer to manufacturer user manusal/operating manual Note: For more details, please refer to the User's manual of the EUT. Report No. ENS2306120066W00501R Page 5 of 41 Ver.1.0 3 SUMMARY OF TEST RESULT FCC Part Clause Test Parameter Verdict Remark 15.407 (a) 15.407 (e) 99% , 6dB and 26dB Bandwidth PASS 15.407 (a) 15.407 (a) 15.407 (b) 15.407(g) Maximum Conducted Output Power Peak Power Spectral Density Radiated Spurious Emission Frequency Stability PASS PASS PASS PASS 15.407 (b)(6) 15.207 Power Line Conducted Emission PASS 15.407(a) 15.203 Antenna Application PASS NOTE1: N/A (Not Applicable) NOTE2: According to FCC OET KDB 789033 D2 General UNII Test Procedures New Rules v02r01, In addition, the radiated test is also performed to ensure the emissions emanating from the device cabinet also comply with the applicable limits. RELATED SUBMITTAL(S) / GRANT(S): This submittal(s) (test report) is intended for FCC ID: 2AJ55HOLYSTONEIW filing to comply with Section 15.407 of the FCC Part 15, Subpart 15E Rules. Report No. ENS2306120066W00501R Page 6 of 41 Ver.1.0 4 TEST METHODOLOGY 4.1 GENERAL DESCRIPTION OF APPLIED STANDARDS According to its specifications, the EUT must comply with the requirements of the following standards: FCC 47 CFR Part 2, Subpart J FCC 47 CFR Part 15, Subpart E FCC KDB 662911 D01 Multiple Transmitter Output v02r01 FCC KDB 789033 D2 General UNII Test Procedures New Rules v02r01 4.2 MEASUREMENT EQUIPMENT USED Conducted Emission Test Equipment Equipment Manufacturer Model No. Serial No. Last Cal. Cal. Interval EMI Test Receiver Rohde & Schwarz ESCI 101384 2023/5/13 1Year AMN Rohde & Schwarz AMN Kyoritsu For Spurious Emissions Test Equipment Manufacturer ENV216 KNW-407 Model No. 101161 8-1492-9 Serial No. 2023/5/13 2023/5/11 Last Cal. 1Year 1Year Cal. Interval Pre-Amplifier Bonn BLMA 011001N 2213967A 2022/10/31 1Year EMI Test Receiver Bilog Antenna Horn antenna Rohde & Schwarz Schwarzbeck Schwarzbeck ESR7 VULB9163 BBHA9120D 102551 9163142 9120D-1198 2022/10/31 2022/7/24 2023/6/2 1Year 2 Year 2 Year Pre-Amplifier Bonn BLMA 0118-5G 2213967B-01 2022/10/31 1Year Spectrum Analyzer Rohde & Schwarz FSV3044 101290 Horn antenna Pre-Amplifier Pre-Amplifier Loop Antenna Band reject Filter(50dB) For other test items: Schwarzbeck Lunar EM Lunar EM Schwarzbeck WI/DE BBHA9170 LNA18G26-40 LNA26G40-40 FMZB1519 9170-399 J101213101000 1 J101313102800 1 1519-012 WRCGV-2400(24002485MHz) 2 Equipment Manufacturer Model No. Serial No. 2022/10/31 2023/5/12 2023/5/10 2023/5/10 2023/5/12 2023/5/10 Last Cal. Signal Analyzer Vector Signal Generater Analog Signal Generator Power Meter Switchgroup MIMO Matrix Switch Temperature&Humidity Chamber Agilent Agilent Agilent Agilent THEDA THEDA ESPEC N9010A MY53470879 N5182B MY53050878 N5171B PS-X10-100 ETF-025(VASC6) 4P5TM18 EL-02KA MY53050553 \ TW5451008 TW5451009 12107166 2023/5/10 2023/5/10 2023/5/10 2023/5/13 N/A N/A 2023/5/10 1Year 2 Year 2 Year 1 Year 1 Year 1 Year Cal. Interval 1Year 1Year 1Year 1Year N/A N/A 1Year Report No. ENS2306120066W00501R Page 7 of 41 Ver.1.0 4.3 DESCRIPTION OF TEST MODES The EUT has been tested under its typical operating condition. The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions requirement and operating in a manner which intends to maximize its emission characteristics in a continuous normal application. The Transmitter was operated in the normal operating mode. The TX frequency was fixed which was for the purpose of the measurements. Test of channel included the lowest and middle and highest frequency to perform the test, then record on this report. Pre-defined engineering program for regulatory testing used to control the EUT for staying in continuous transmitting and receiving mode is programmed. Wifi 5G with U-NII - 1 Frequency and Channel list for 802.11n (HT20): Channel Frequency (MHz) 36 5180 Test Frequency and Channel for 802.11n (HT20): Channel Frequency (MHz) 36 5180 Report No. ENS2306120066W00501R Page 8 of 41 Ver.1.0 5 FACILITIES AND ACCREDITATIONS 5.1 FACILITIES All measurement facilities used to collect the measurement data are located at: EMTEK (Shenzhen) Co., Ltd. Building 69, Majialong Industry Zone District, Nanshan District, Shenzhen, China The sites are constructed in conformance with the requirements of ANSI C63.7, ANSI C63.4 and CISPR Publication 22. 5.2 EQUIPMENT Radiated emissions are measured with one or more of the following types of linearly polarized antennas: tuned dipole, biconical, log periodic, bi-log, and/or ridged waveguide, horn. Spectrum analyzers with preselectors and quasi-peak detectors are used to perform radiated measurements. Conducted emissions are measured with Line Impedance Stabilization Networks and EMI Test Receivers. Calibrated wideband preamplifiers, coaxial cables, and coaxial attenuators are also used for making measurements. All receiving equipment conforms to CISPR Publication 16-1, "Radio Interference Measuring Apparatus and Measurement Methods." 5.3 LABORATORY ACCREDITATIONS AND LISTINGS Site Description EMC Lab. : Accredited by CNAS The Certificate Registration Number is L2291. The Laboratory has been assessed and proved to be in compliance with CNAS-CL01 (identical to ISO/IEC 17025:2017) Accredited by FCC Designation Number: CN1204 Test Firm Registration Number: 882943 Accredited by A2LA The Certificate Number is 4321.01. Name of Firm Site Location Accredited by Industry Canada The Conformity Assessment Body Identifier is CN0008 : EMTEK (SHENZHEN) CO., LTD. : Building 69, Majialong Industry Zone, Nanshan District, Shenzhen, Guangdong, China Report No. ENS2306120066W00501R Page 9 of 41 Ver.1.0 6 TEST SYSTEM UNCERTAINTY The following measurement uncertainty levels have been estimated for tests performed on the apparatus: Parameter Uncertainty Radio Frequency ±1x10^-5 Maximum Peak Output Power Test ±1.0dB Conducted Emissions Test ±2.0dB Radiated Emission Test ±2.0dB Power Density ±2.0dB Occupied Bandwidth Test ±1.0dB Band Edge Test ±3dB All emission, radiated ±3dB Antenna Port Emission ±3dB Temperature ±0.5 Humidity ±3% Measurement Uncertainty for a level of Confidence of 95% Report No. ENS2306120066W00501R Page 10 of 41 Ver.1.0 7 SETUP OF EQUIPMENT UNDER TEST 7.1 RADIO FREQUENCY TEST SETUP The WLAN component's antenna ports(s) of the EUT are connected to the measurement instrument per an appropriate attenuator. The EUT is controlled by PC/software to emit the specified signals for the purpose of measurements. EUT Attenuator Measurement Instrument 7.2 RADIO FREQUENCY TEST SETUP The test site semi-anechoic chamber has met the requirement of NSA tolerance 4 dB according to the standards: ANSI C63.10. The test distance is 3m.The setup is according to the requirements in Section 13.1.4.1 of ANSI C63.10-2013 and CAN/CSA-CEI/IEC CISPR 22. Below 30MHz The EUT is placed on a turntable 0.8 meters above the ground in the chamber, 3 meter away from the antenna (loop antenna). The Antenna should be positioned with its plane vertical at the specified distance from the EUT and rotated about its vertical axis for maximum response at each azimuth about the EUT. The center of the loop shall be 1 m above the ground. For certain applications, the loop antenna plane may also need to be positioned horizontally at the specified distance from the EUT. Above 30MHz The EUT is placed on a turntable 0.8 meters above the ground in the chamber, 3 meter away from the antenna. The maximal emission value is acquired by adjusting the antenna height, polarisation and turntable azimuth. Normally, the height range of antenna is 1 m to 4 m, the azimuth range of turntable is 0° to 360°, and the receive antenna has two polarizations Vertical (V) and Horizontal (H). Above 1GHz (Note: the FCC's permission to use 1.5m as an alternative per TCBC Conf call of Dec. 2, 2014.) The EUT is placed on a turntable 1.5 meters above the ground in the chamber, 3 meter away from the antenna. The maximal emission value is acquired by adjusting the antenna height, polarisation and turntable azimuth. Normally, the height range of antenna is 1 m to 4 m, the azimuth range of turntable is 0° to 360°, and the receive antenna has two polarizations Vertical (V) and Horizontal (H). (a) Radiated Emission Test Set-Up, Frequency Below 30MHz Turntable EUT Ground Plane 3m 0.8 m Coaxial Cable Test Receiver Report No. ENS2306120066W00501R Page 11 of 41 Ver.1.0 (b) Radiated Emission Test Set-Up, Frequency Below 1000MHz Turntable Test Receiver EUT Ground Plane 3m 0.8m 1m to 4m Coaxial Cable (c) Radiated Emission Test Set-Up, Frequency above 1000MHz Turntable EUT 3m 4m 1.5m 1m Test Amplifier Receiver Report No. ENS2306120066W00501R Page 12 of 41 Ver.1.0 7.3 CONDUCTED EMISSION TEST SETUP The mains cable of the EUT (maybe per AC/DC Adapter) must be connected to LISN. The LISN shall be placed 0.8 m from the boundary of EUT and bonded to a ground reference plane for LISN mounted on top of the ground reference plane. This distance is between the closest points of the LISN and the EUT. All other units of the EUT and associated equipment shall be at least 0.8m from the LISN. Ground connections, where required for safety purposes, shall be connected to the reference ground point of the LISN and, where not otherwise provided or specified by the manufacturer, shall be of same length as the mains cable and run parallel to the mains connection at a separation distance of not more than 0.1 m. According to the requirements in Section 13.1.4.1 of ANSI C63.10-2013 Conducted emissions from the EUT measured in the frequency range between 0.15 MHz and 30 MHz using CISPR Quasi-Peak and average detector mode. Reference Ground EMI Receiver EUT Auxiliary Equipment Reference Ground LISN 80cm 50 80cm LISN Report No. ENS2306120066W00501R Page 13 of 41 Ver.1.0 7.4 BLOCK DIAGRAM CONFIGURATION OF TEST SYSTEM EUT DC INPUT 7.5 SUPPORT EQUIPMENT EUT Cable List and Details Cable Description Length (m) / / Shielded/Unshielded / With / Without Ferrite / Auxiliary Cable List and Details Cable Description Length (m) / / Shielded/Unshielded / With / Without Ferrite / Auxiliary Equipment List and Details Description Manufacturer Notebook Lenove Model M713A Serial Number SA12582190 Notes: 1.All the equipment/cables were placed in the worst-case configuration to maximize the emission during the test. 2.Grounding was established in accordance with the manufacturer's requirements and conditions for the intended use. Report No. ENS2306120066W00501R Page 14 of 41 Ver.1.0 8 TEST REQUIREMENTS 8.1 BANDWIDTH MEASUREMENT 8.1.1 Applicable Standard According to FCC Part 15.407(a)(1) for UNII Band I According to FCC Part 15.407(a)(2) for UNII Band II-A and UNII Band II-C According to FCC Part 15.407(a)(3) for UNII Band III According to FCC Part 15.407(e) for UNII Band III According to 789033 D02 Section II(C) According to 789033 D02 Section II(D) 8.1.2 Conformance Limit (1) For the band 5.15-5.25 GHz. (iv) For mobile and portable client devices in the 5.15-5.25 GHz band, the maximum conducted output power over the frequency band of operation shall not exceed 250 mW provided the maximum antenna gain does not exceed 6 dBi. In addition, the maximum power spectral density shall not exceed 11 dBm in any 1 megahertz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the maximum power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. (2) For the 5.25-5.35 GHz and 5.47-5.725 GHz bands, the maximum conducted output power over the frequency bands of operation shall not exceed the lesser of 250 mW or 11 dBm + 10 log B, where B is the 26 dB emission bandwidth in megahertz. In addition, the maximum power spectral density shall not exceed 11 dBm in any 1 megahertz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the maximum power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. (3) For the band 5.725-5.85 GHz, the maximum conducted output power over the frequency band of operation shall not exceed 1 W. In addition, the maximum power spectral density shall not exceed 30 dBm in any 500-kHz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the maximum power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. However, fixed point-to-point U-NII devices operating in this band may employ transmitting antennas with directional gain greater than 6 dBi without any corresponding reduction in transmitter conducted power. Fixed, point-to-point operations exclude the use of point-to-multipoint systems, omnidirectional applications, and multiple collocated transmitters transmitting the same information. The operator of the U-NII device, or if the equipment is professionally installed, the installer, is responsible for ensuring that systems employing high gain directional antennas are used exclusively for fixed, point-to-point operations. (e) Within the 5.725-5.85 GHz band, the minimum 6 dB bandwidth of U-NII devices shall be at least 500 kHz. 8.1.3 Test Configuration Test according to clause 7.1 radio frequency test setup 8.1.4 Test Procedure According to 789033 D02 v02r01 section C&D, the following is the measurement procedure. 1. Emission Bandwidth (EBW) a) Set RBW = approximately 1% of the emission bandwidth. b) Set the VBW > RBW. c) Detector = Peak. d) Trace mode = max hold. e) Measure the maximum width of the emission that is 26 dB down from the maximum of the emission. Report No. ENS2306120066W00501R Page 15 of 41 Ver.1.0 Compare this with the RBW setting of the analyzer. Readjust RBW and repeat measurement as needed until the RBW/EBW ratio is approximately 1%. 2. Minimum Emission Bandwidth for the band 5.725-5.85 GHz Section 15.407(e) specifies the minimum 6 dB emission bandwidth of at least 500 KHz for the band 5.715-5.85 GHz. The following procedure shall be used for measuring this bandwidth: a) Set RBW = 100 kHz. b) Set the video bandwidth (VBW) 3 × RBW. c) Detector = Peak. d) Trace mode = max hold. e) Sweep = auto couple. f) Allow the trace to stabilize. g) Measure the maximum width of the emission that is constrained by the frequencies associated with the two outermost amplitude points (upper and lower frequencies) that are attenuated by 6 dB relative to the maximum level measured in the fundamental emission. Note: The automatic bandwidth measurement capability of a spectrum analyzer or EMI receiver may be employed if it implements the functionality described above. D. 99 Percent Occupied Bandwidth The 99-percent occupied bandwidth is the frequency bandwidth such that, below its lower and above its upper frequency limits, the mean powers are each equal to 0.5 % of the total mean power of the given emission. Measurement of the 99-percent occupied bandwidth is required only as a condition for using the optional band-edge measurement techniques described in section II.G.3.d). Measurements of 99-percent occupied bandwidth may also optionally be used in lieu of the EBW to 789033 D02 v01r02 General UNII Test Procedures New Rules v01 define the minimum frequency range over which the spectrum is integrated when measuring maximum conducted output power as described in section II.E. However, the EBW must be measured to determine bandwidth dependent limits on maximum conducted output power in accordance with 15.407(a). The following procedure shall be used for measuring (99 %) power bandwidth: 1. Set center frequency to the nominal EUT channel center frequency. 2. Set span = 1.5 times to 5.0 times the OBW. 3. Set RBW = 1 % to 5 % of the OBW 4. Set VBW 3 · RBW 5. Video averaging is not permitted. Where practical, a sample detection and single sweep mode shall be used. Otherwise, peak detection and max hold mode (until the trace stabilizes) shall be used. 6. Use the 99 % power bandwidth function of the instrument (if available). 7. If the instrument does not have a 99 % power bandwidth function, the trace data points are recovered and directly summed in power units. The recovered amplitude data points, beginning at the lowest frequency, are placed in a running sum until 0.5 % of the total is reached; that frequency is recorded as the lower frequency. The process is repeated until 99.5 % of the total is reached; that frequency is recorded as the upper frequency. The 99% occupied bandwidth is the difference between these two frequencies. Report No. ENS2306120066W00501R Page 16 of 41 Ver.1.0 8.1.5 Test Results TestMode Antenna Frequency[MHz] 11N20SISO Ant1 5180 26db EBW [MHz] 33.120 FL[MHz] FH[MHz] Limit[MHz] Verdict 5163.800 5196.920 --- --- Report No. ENS2306120066W00501R Page 17 of 41 Ver.1.0 11N20SISO_Ant1_5180 Report No. ENS2306120066W00501R Page 18 of 41 Ver.1.0 TestMode Antenna Frequency[MHz] 11N20SISO Ant1 5180 OCB [MHz] 18.713 FL[MHz] FH[MHz] Limit[MHz] Verdict 5170.8648 5189.5778 --- --- Report No. ENS2306120066W00501R Page 19 of 41 Ver.1.0 11N20SISO_Ant1_5180 Report No. ENS2306120066W00501R Page 20 of 41 Ver.1.0 8.2 MAXIMUM CONDUCTED OUTPUT POWER 8.2.1 Applicable Standard According to FCC Part 15.407(a)(1) for UNII Band I According to FCC Part 15.407(a)(2) for UNII Band II-A and UNII Band II-C According to FCC Part 15.407(a)(3) for UNII Band III According to 789033 D02 Section II(E) 8.2.2 Conformance Limit For the band 5.15-5.25 GHz, (a) (1) (i) For an outdoor access point operating in the band 5.15-5.25 GHz, the maximum conducted output power over the frequency band of operation shall not exceed 1 W provided the maximum antenna gain does not exceed 6 dBi. In addition, the maximum power spectral density shall not exceed 17 dBm in any 1 megahertz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the maximum power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. The maximum e.i.r.p. at any elevation angle above 30 degrees as measured from the horizon must not exceed 125 mW (21 dBm). (a) (1) (ii) For an indoor access point operating in the band 5.15-5.25 GHz, the maximum conducted output power over the frequency band of operation shall not exceed 1 W provided the maximum antenna gain does not exceed 6 dBi. In addition, the maximum power spectral density shall not exceed 17 dBm in any 1 megahertz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the maximum power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. (a) (1) (iii) For fixed point-to-point access points operating in the band 5.15-5.25 GHz, the maximum conducted output power over the frequency band of operation shall not exceed 1 W. In addition, the maximum power spectral density shall not exceed 17 dBm in any 1 megahertz band. Fixed point-to-point U-NII devices may employ antennas with directional gain up to 23 dBi without any corresponding reduction in the maximum conducted output power or maximum power spectral density. For fixed point-to-point transmitters that employ a directional antenna gain greater than 23 dBi, a 1 dB reduction in maximum conducted output power and maximum power spectral density is required for each 1 dB of antenna gain in excess of 23 dBi. Fixed, point-to-point operations exclude the use of point-to-multipoint systems, omnidirectional applications, and multiple collocated transmitters transmitting the same information. The operator of the U-NII device, or if the equipment is professionally installed, the installer, is responsible for ensuring that systems employing high gain directional antennas are used exclusively for fixed, point-to-point operations. (a) (1) (iv) For client devices in the 5.15-5.25 GHz band, the maximum conducted output power over the frequency band of operation shall not exceed 250 mW provided the maximum antenna gain does not exceed 6 dBi. In addition, the maximum power spectral density shall not exceed 11 dBm in any 1 megahertz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the maximum power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. For the 5.25-5.35 GHz and 5.47-5.725 GHz bands (a) (2) The maximum conducted output power over the frequency bands of operation shall not exceed the lesser of 250 mW or 11 dBm + 10 log B, where B is the 26 dB emission bandwidth in megahertz. In addition, the maximum power spectral density shall not exceed 11 dBm in any 1 megahertz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the maximum power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. For the band 5.725-5.85 GHz (a) (3) for the band 5.725-5.85 GHz, the maximum conducted output power over the frequency band of operation shall not exceed 1 W. In addition, the maximum power spectral density shall not exceed 30 Report No. ENS2306120066W00501R Page 21 of 41 Ver.1.0 dBm in any 500-kHz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the maximum power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. However, fixed point-to-point U-NII devices operating in this band may employ transmitting antennas with directional gain greater than 6 dBi without any corresponding reduction in transmitter conducted power. Fixed, point-to-point operations exclude the use of point-to-multipoint systems, omnidirectional applications, and multiple collocated transmitters transmitting the same information. The operator of the U-NII device, or if the equipment is professionally installed, the installer, is responsible for ensuring that systems employing high gain directional antennas are used exclusively for fixed, point-to-point operations 8.2.3 Test Configuration Test according to clause 6.1 radio frequency test setup 8.2.4 Test Procedure The maximum average conducted output power can be measured using Method PM-G (Measurement using a gated RF average power meter): Measurements may be performed using a wideband gated RF power meter provided that the gate parameters are adjusted such that the power is measured only when the EUT is transmitting at its maximum power control level. Since the measurement is made only during the ON time of the transmitter, no duty cycle correction factor is required. a. The Transmitter output (antenna port) was connected to the power meter. b. Turn on the EUT and power meter and then record the power value. c. Repeat above procedures on all channels needed to be tested. 8.2.5 Test Results Report No. ENS2306120066W00501R Page 22 of 41 Ver.1.0 TestMode Antenna Frequency[MHz] 11N20SISO Ant1 5180 TransmissionDuration [ms] 1.89 Transmission Period [ms] 1.90 Duty Cycle [%] 99.47 Report No. ENS2306120066W00501R Page 23 of 41 Ver.1.0 11N20SISO_Ant1_5180 Report No. ENS2306120066W00501R Page 24 of 41 Ver.1.0 Test Mode Antenna Frequency[MHz] ChannelPowert [dBm] 11N20MIMO Ant1 5180 13.63 NoteThe Duty Cycle Factoriscompensatedinthegraph. Duty Cycle [%] 99.47 DC Factor [dBm] 0.02 Result [dBm] 13.65 Limit [dBm] 23.98 Verdict PASS Report No. ENS2306120066W00501R Page 25 of 41 Ver.1.0 11N20SISO_Ant1_5180 Report No. ENS2306120066W00501R Page 26 of 41 Ver.1.0 8.3 MAXIMUM PEAK POWER DENSITY 8.3.1 Applicable Standard According to FCC Part 15.407(a)(1) for UNII Band I According to FCC Part 15.407(a)(2) for UNII Band II-A and UNII Band II-C According to FCC Part 15.407(a)(3) for UNII Band III According to 789033 D02 Section II(F) 8.3.2 Conformance Limit For the band 5.15-5.25 GHz, (a) (1) (i) For an outdoor access point operating in the band 5.15-5.25 GHz, the maximum conducted output power over the frequency band of operation shall not exceed 1 W provided the maximum antenna gain does not exceed 6 dBi. In addition, the maximum power spectral density shall not exceed 17 dBm in any 1 megahertz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the maximum power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. The maximum e.i.r.p. at any elevation angle above 30 degrees as measured from the horizon must not exceed 125 mW (21 dBm). (a) (1) (ii) For an indoor access point operating in the band 5.15-5.25 GHz, the maximum conducted output power over the frequency band of operation shall not exceed 1 W provided the maximum antenna gain does not exceed 6 dBi. In addition, the maximum power spectral density shall not exceed 17 dBm in any 1 megahertz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the maximum power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. (a) (1) (iii) For fixed point-to-point access points operating in the band 5.15-5.25 GHz, the maximum conducted output power over the frequency band of operation shall not exceed 1 W. In addition, the maximum power spectral density shall not exceed 17 dBm in any 1 megahertz band. Fixed point-to-point U-NII devices may employ antennas with directional gain up to 23 dBi without any corresponding reduction in the maximum conducted output power or maximum power spectral density. For fixed point-to-point transmitters that employ a directional antenna gain greater than 23 dBi, a 1 dB reduction in maximum conducted output power and maximum power spectral density is required for each 1 dB of antenna gain in excess of 23 dBi. Fixed, point-to-point operations exclude the use of point-to-multipoint systems, omnidirectional applications, and multiple collocated transmitters transmitting the same information. The operator of the U-NII device, or if the equipment is professionally installed, the installer, is responsible for ensuring that systems employing high gain directional antennas are used exclusively for fixed, point-to-point operations. (a) (1) (iv) For client devices in the 5.15-5.25 GHz band, the maximum conducted output power over the frequency band of operation shall not exceed 250 mW provided the maximum antenna gain does not exceed 6 dBi. In addition, the maximum power spectral density shall not exceed 11 dBm in any 1 megahertz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the maximum power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. For the 5.25-5.35 GHz and 5.47-5.725 GHz bands (b) (2) The maximum conducted output power over the frequency bands of operation shall not exceed the lesser of 250 mW or 11 dBm + 10 log B, where B is the 26 dB emission bandwidth in megahertz. In addition, the maximum power spectral density shall not exceed 11 dBm in any 1 megahertz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the maximum power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. For the band 5.725-5.85 GHz (a) (3) for the band 5.725-5.85 GHz, the maximum conducted output power over the frequency band of operation shall not exceed 1 W. In addition, the maximum power spectral density shall not exceed 30 Report No. ENS2306120066W00501R Page 27 of 41 Ver.1.0 dBm in any 500-kHz band. If transmitting antennas of directional gain greater than 6 dBi are used, both the maximum conducted output power and the maximum power spectral density shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi. However, fixed point-to-point U-NII devices operating in this band may employ transmitting antennas with directional gain greater than 6 dBi without any corresponding reduction in transmitter conducted power. Fixed, point-to-point operations exclude the use of point-to-multipoint systems, omnidirectional applications, and multiple collocated transmitters transmitting the same information. The operator of the U-NII device, or if the equipment is professionally installed, the installer, is responsible for ensuring that systems employing high gain directional antennas are used exclusively for fixed, point-to-point operations 8.3.3 Test Configuration Test according to clause 6.1 radio frequency test setup 8.3.4 Test Procedure Methods refer to FCC KDB 789033 For devices operating in the bands 5.15-5.25 GHz, 5.25-5.35 GHz, and 5.47-5.725 GHz, the above procedures make use of 1 MHz RBW to satisfy directly the 1 MHz reference bandwidth specified in § 15.407(a)(5). For devices operating in the band 5.725-5.85 GHz, the rules specify a measurement bandwidth of 500 kHz. Many spectrum analyzers do not have 500 kHz RBW, thus a narrower RBW may need to be used. The rules permit the use of a RBWs less than 1 MHz, or 500 kHz, "provided that the measured power is integrated over the full reference bandwidth" to show the total power over the specified measurement bandwidth (i.e., 1 MHz, or 500 kHz). If measurements are performed using a reduced resolution bandwidth (< 1 MHz, or < 500 kHz) and integrated over 1 MHz, or 500 KHz bandwidth, the following adjustments to the procedures apply: a) Set RBW 1/T, where T is defined in section II.B.l.a). b) Set VBW 3 RBW. c) If measurement bandwidth of Maximum PSD is specified in 500 kHz, add 10log(500kHz/RBW) to the measured result, whereas RBW (< 500 KHz) is the reduced resolution bandwidth of the spectrum analyzer set during measurement. d) If measurement bandwidth of Maximum PSD is specified in 1 MHz, add 10log(1MHz/RBW) to the measured result, whereas RBW (< 1 MHz) is the reduced resolution bandwidth of spectrum analyzer set during measurement. e) Care must be taken to ensure that the measurements are performed during a period of continuous transmission or are corrected upward for duty cycle. Note: As a practical matter, it is recommended to use reduced RBW of 100 KHz for the sections 5.c) and 5.d) above, since RBW=100 KHZ is available on nearly all spectrum analyzers. Report No. ENS2306120066W00501R Page 28 of 41 Ver.1.0 8.3.5 Test Results TestMode 11N20SISO Antenna Ant1 Frequency[MHz] 5180 Result [dBm/MHz] 2.06 Limit[dBm/MHz] 11.00 Verdict PASS Report No. ENS2306120066W00501R Page 29 of 41 Ver.1.0 11N20SISO_Ant1_5180 Report No. ENS2306120066W00501R Page 30 of 41 Ver.1.0 8.4 UNDESIRABLE RADIATED SPURIOUS EMISSION 8.4.1 Applicable Standard According to FCC Part 15.407 (b) According to 789033 D02 Section II(G) 8.4.2 Conformance Limit For transmitters operating in the 5.15-5.25 GHz band: All emissions outside of the 5.15-5.35 GHz band shall not exceed an e.i.r.p. of -27 dBm/MHz. For transmitters operating in the 5.25-5.35 GHz band: All emissions outside of the 5.15-5.35 GHz band shall not exceed an e.i.r.p. of -27 dBm/MHz. For transmitters operating in the 5.47-5.725 GHz band: All emissions outside of the 5.47-5.725 GHz band shall not exceed an e.i.r.p. of -27 dBm/MHz. For transmitters operating in the 5.725-5.85 GHz band: All emissions shall be limited to a level of -27 dBm/MHz at 75 MHz or more above or below the band edge increasing linearly to 10 dBm/MHz at 25 MHz above or below the band edge, and from 25 MHz above or below the band edge increasing linearly to a level of 15.6 dBm/MHz at 5 MHz above or below the band edge, and from 5 MHz above or below the band edge increasing linearly to a level of 27 dBm/MHz at the band edge. The emission measurements shall be performed using a minimum resolution bandwidth of 1 MHz. A lower resolution bandwidth may be employed near the band edge, when necessary, provided the measured energy is integrated to show the total power over 1 MHz. Unwanted emissions below 1 GHz must comply with the general field strength limits set forth in §15.209 The emissions from an intentional radiator shall not exceed the field strength levels specified in the following table 15.209(a): Restricted Field Strength (V/m) Field Strength Measurement Frequency(MHz) (dBV/m) Distance 0.009-0.490 2400/F(KHz) 20 log (uV/m) 300 0.490-1.705 24000/F(KHz) 20 log (uV/m) 30 1.705-30 30 29.5 30 30-88 100 40 3 88-216 150 43.5 3 216-960 200 46 3 Above 960 500 54 3 The provisions of §15.205 apply to intentional radiators operating under this section,15.205 Restricted bands of operation MHz MHz MHz GHz 0.090-0.110 16.42-16.423 399.9-410 4.5-5.15 10.495-0.505 16.69475-16.69525 608-614 5.35-5.46 2.1735-2.1905 16.80425-16.80475 960-1240 7.25-7.75 4.125-4.128 25.5-25.67 1300-1427 8.025-8.5 4.17725-4.17775 37.5-38.25 1435-1626.5 9.0-9.2 4.20725-4.20775 73-74.6 1645.5-1646.5 9.3-9.5 6.215-6.218 74.8-75.2 1660-1710 10.6-12.7 6.26775-6.26825 123-138 2200-2300 14.47-14.5 8.291-8.294 149.9-150.05 2310-2390 15.35-16.2 8.362-8.366 156.52475-156.52525 2483.5-2500 17.7-21.4 8.37625-8.38675 156.7-156.9 2690-2900 22.01-23.12 8.41425-8.41475 162.0125-167.17 3260-3267 23.6-24.0 12.29-12.293 167.72-173.2 3332-3339 31.2-31.8 12.51975-12.52025 240-285 3345.8-3358 36.43-36.5 12.57675-12.57725 322-335.4 3600-4400 (2) 13.36-13.41 Report No. ENS2306120066W00501R Page 31 of 41 Ver.1.0 Remark: 1. Emission level in dBuV/m=20 log (uV/m) 2. Measurement was performed at an antenna to the closed point of EUT distance of meters. 3. Only spurious frequency is permitted to locate within the Restricted Bands specified in provision of 15.205, and the emissions located in restricted bands also comply with 15.209 limit. 8.4.3 Test Configuration Test according to clause 6.2 radio frequency test setup 8.4.4 Test Procedure Unwanted Emissions Measurements below 1000 MHz Compliance shall be demonstrated using CISPR quasi-peak detection; however, peak detection is permitted as an alternative to quasi-peak detection. The EUT was placed on a turn table which is 0.8m above ground plane. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. Repeat above procedures until all frequency measured was complete. We use software control the EUT, Let EUT hopping on and transmit with highest power, All the modes have been tested and the worst result was reported. Use the following spectrum analyzer settings: Set RBW=120kHz for f < 1 GHz(30MHz to 1GHz), 200Hz for f<150KHz(9KHz to 150KHz), 9KHz for <30MHz (150KHz to 30KHz). Set the VBW > RBW. Detector = Peak. Trace mode = max hold. Follow the guidelines in ANSI C63.10-2013 with respect to maximizing the emission by rotating the EUT, measuring the emission while the EUT is situated in three orthogonal planes (if appropriate), adjusting the measurement antenna height and polarization, etc. A pre-amp and a high pass filter are required for this test, in order to provide the measuring system with sufficient sensitivity. Allow the trace to stabilize. The peak reading of the emission, after being corrected by the antenna factor, cable loss, pre-amp gain, etc., is the peak field strength, which must comply with the limit specified in Section 15.35(b). Submit this data. Repeat above procedures until all frequency measured was complete. Unwanted Maximum peak Emissions Measurements above 1000 MHz Maximum emission levels are measured by setting the analyzer as follows: RBW = 1 MHz. VBW 3 MHz. Detector = Peak. Sweep time = auto. Trace mode = max hold. Allow sweeps to continue until the trace stabilizes. Note that if the transmission is not continuous, the time required for the trace to stabilize will increase by a factor of approximately 1/x, where x is the duty cycle. For example, at 50 percent duty cycle, the measurement time will increase by a factor of two relative to measurement time for continuous transmission. Unwanted Average Emissions Measurements above 1000 MHz Method VB (Averaging using reduced video bandwidth): Alternative method. RBW = 1 MHz. Video bandwidth. · If the EUT is configured to transmit with duty cycle 98 percent, set VBW RBW/100 (i.e., 10 kHz) but not less than 10 Hz. · If the EUT duty cycle is < 98 percent, set VBW 1/T, where T is defined in section II.B.1.a). Video bandwidth mode or display mode · The instrument shall be set to ensure that video filtering is applied in the power domain. Typically, this requires setting the detector mode to RMS and setting the Average-VBW Type to Power (RMS). · As an alternative, the analyzer may be set to linear detector mode. Ensure that video filtering is applied in linear voltage domain (rather than in a log or dB domain). Some analyzers require linear display mode in order to accomplish this. Others have a setting for Average-VBW Type, which can be set to "Voltage" regardless of the display mode. Report No. ENS2306120066W00501R Page 32 of 41 Ver.1.0 Detector = Peak. Sweep time = auto. Trace mode = max hold. Allow max hold to run for at least 50 traces if the transmitted signal is continuous or has at least 98 percent duty cycle. For lower duty cycles, increase the minimum number of traces by a factor of 1/x, where x is the duty cycle. For example, use at least 200 traces if the duty cycle is 25 percent. (If a specific emission is demonstrated to be continuous--i.e., 100 percent duty cycle--rather than turning on and off with the transmit cycle, at least 50 traces shall be averaged.) Band edge measurements. Unwanted band-edge emissions may be measured using either of the special band-edge measurement techniques (the marker-delta or integration methods) described below. Note that the marker-delta method is primarily a radiated measurement technique that requires the 99% occupied bandwidth edge to be within 2 MHz of the authorized band edge, whereas the integration method can be used in either a radiated or conducted measurement without any special requirement with regards to the displacement of the unwanted emission(s) relative to the authorized bandwidth. Marker-Delta Method. The marker-delta method, as described in ANSI C63.10, can be used to perform measurements of the radiated unwanted emissions level of emissions provided that the 99% occupied bandwidth of the fundamental is within 2 MHz of the authorized band-edge. 8.4.5 Test Results Temperature: Relative Humidity: ATM Pressure: 26 C 54 1011 mbar Spurious Emission below 30MHz(9KHz to 30MHz) Freq. (MHz) Ant.Pol. H/V Emission Level(dBuV/m) PK AV Limit 3m(dBuV/m) PK AV Over(dB) PK AV -- -- -- -- -- -- -- -- Note: the amplitude of spurious emission that is attenuated by more than 20dB below the permissible limit has no need to be reported. Distance extrapolation factor =40log(Specific distance/ test distance)( dB); Limit line=Specific limits(dBuV) + distance extrapolation factor Report No. ENS2306120066W00501R Page 33 of 41 Ver.1.0 For Undesirable radiated Spurious Emission in U-NII 1 Undesirable radiated Spurious Emission Above 1GHz (1GHz to 40GHz) All the antenna(Antenna 1) and modes(802.11n) has been tested and the worst(Antenna 1,802.11n) result recorded was report as below: Test mode: 802.11n Frequency(MHz): 5180 Freq. (MHz) 11383.6918 14572.7864 17506.7534 11545.2726 14589.7949 17489.7449 Ant.Pol. V V V H H H Field Strength (dBuV/m) 47.47 47.23 47.23 47.75 47.09 47.03 E.I.R.P (dBm) -35.52 -32.44 -28.61 -35.80 -32.27 -28.74 Limit (dBm) -27 -27 -27 -27 -27 -27 Over(dB) -20.76 -21.00 -21.00 -20.48 -21.14 -21.20 Note: (1) All Readings are Peak Value (VBW=3MHz) and Average Value (VBW=10Hz). (2) Emission Level= Reading Level+Probe Factor +Cable Loss. (3)EIRP[dBm] = E[dBV/m] + 20 log(d[meters]) - 104.77 d is the measurement distance in 3 meters Test mode: 802.11n Frequency(MHz): 5180 Freq. (MHz) 11383.6918 14572.7864 17506.7534 11545.2726 14589.7949 17489.7449 Ant.Pol. H/V V V V H H H Emission Level(dBuV/m) PK AV 59.12 47.47 63.71 47.23 67.20 47.23 58.86 47.75 63.15 47.09 67.19 47.03 Limit 3m(dBuV/m) PK 74.00 74.00 74.00 74.00 74.00 74.00 AV 54.00 54.00 54.00 54.00 54.00 54.00 Over(dB) PK AV 14.88 6.53 10.29 6.77 6.80 6.77 15.14 6.25 10.85 6.91 6.81 6.97 Note: (1) All Readings are Peak Value (VBW=3MHz) and Average Value (VBW=10Hz). (2) Emission Level= Reading Level+Correct Factor. (3) Correct Factor= Ant_F + Cab_L - Preamp (4) The reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. Report No. ENS2306120066W00501R Page 34 of 41 Ver.1.0 Undesirable radiated Undesirable radiated Spurious Emission in Band Edge Test mode: Freq. (MHz) 4973.76 5031.7 802.11n Ant.Pol. H V Frequency(MHz): 5180 Field Strength (RBW=100KHz) (dBuV/m) 48.48 E.I.R.P (dBm) -46.75 Limit (dBm) -27 48.72 -46.51 -27 Test mode: 802.11n Frequency(MHz): 5180 Freq. (MHz) 5351.81 Ant.Pol. H Field Strength (RBW=100KHz) (dBuV/m) 40.52 E.I.R.P (dBm) -54.71 Limit (dBm) -27 5351.69 V 41.38 -53.85 -27 Note: (1) All Readings are Peak Value (VBW=3MHz) and AV Value (VBW=10Hz). (2) Emission Level= Reading Level+Probe Factor +Cable Loss. (3)EIRP[dBm] = E[dBV/m] + 20 log(d[meters]) - 104.77 d is the measurement distance in 3 meters Verdict Pass Pass Verdict Pass Pass Test mode: 802.11n Frequency(MHz): 5180 Frequency (MHz) 4973.76 5031.7 Polarity H V PK(dBuV/m) (VBW=3MHz) 53.72 54.54 Limit 3m (dBuV/m) 74 74 AV(dBuV/m) (VBW=10Hz) 48.48 48.72 Limit 3m (dBuV/m) 54 54 Test mode: 802.11n Frequency(MHz): 5180 Frequency (MHz) Polarity PK(dBuV/m) (VBW=3MHz) Limit 3m (dBuV/m) AV(dBuV/m) (VBW=10Hz) Limit 3m (dBuV/m) 5351.81 H 52.90 74 40.52 54 5351.69 V 52.41 74 41.38 54 Note: (1) All Readings are Peak Value (VBW=3MHz) and Average Value (VBW=10Hz). (2) Emission Level= Reading Level+Correct Factor. (3) Correct Factor= Ant_F + Cab_L - Preamp (4) The reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. Report No. ENS2306120066W00501R Page 35 of 41 Ver.1.0 Test Model U-NII - 1 Undesirable radiated Spurious Emission in Restricted Band (5100-5150MHz) 802.11a 802.11n(HT20) 802.11n(HT40) 5180 5200 5240 Ant.Pol H Test Model U-NII - 1 Undesirable radiated Spurious Emission in Restricted Band (5100-5150MHz) 802.11a 802.11n(HT20) 802.11n(HT40) 5180 5200 5240 Ant.Pol V Report No. ENS2306120066W00501R Page 36 of 41 Ver.1.0 Test Model U-NII - 1 Undesirable radiated Spurious Emission in Restricted Band (5350-5400MHz ) 802.11a 802.11n(HT20) 802.11n(HT40) 5180 5200 5240 Ant.Pol H Test Model U-NII - 1 Undesirable radiated Spurious Emission in Restricted Band (5350-5400MHz ) 802.11a 802.11n(HT20) 802.11n(HT40) 5180 5200 5240 Ant.Pol V Report No. ENS2306120066W00501R Page 37 of 41 Ver.1.0 Undesirable radiated Spurious Emission below 1GHz (30MHz to 1GHz) All the antenna(Antenna 1) and modes(802.11n) has been tested and the worst(Antenna 1,802.11n) result recorded was report as below: Mode: 11n 5180 Suspected Data List NO. Freq. [MHz] Reading [dBV] 1 40.6807 48.95 2 65.9259 50.94 3 175.645 6 34.56 4 273.713 7 31.48 5 669.869 9 31.18 6 958.248 2 30.72 Factor [dB/m] -17.86 -19.39 -18.64 -14.54 -6.15 -2.29 Level [dBV/m] 31.09 31.55 15.92 16.94 25.03 28.43 Detector PK PK PK PK PK PK Limit [dBV/m] 40.00 40.00 43.50 46.00 46.00 46.00 Margin [dB] 8.91 8.45 27.58 29.06 20.97 17.57 Polarity Vertical Vertical Vertical Vertical Vertical Vertical Report No. ENS2306120066W00501R Page 38 of 41 Ver.1.0 Mode: 11n 5180 Suspected Data List NO. Freq. [MHz] Reading [dBV] 1 33.8839 41.13 2 48.4484 39.47 3 98.9389 31.82 4 214.484 5 30.78 5 471.791 8 32.27 6 770.850 9 30.86 Factor [dB/m] -18.29 -17.32 -17.05 -17.12 -10.30 -4.97 Level [dBV/m] 22.84 22.15 14.77 13.66 21.97 25.89 Detector PK PK PK PK PK PK Limit [dBV/m] 40.00 40.00 43.50 43.50 46.00 46.00 Margin [dB] 17.16 17.85 28.73 29.84 24.03 20.11 Polarity Horizontal Horizontal Horizontal Horizontal Horizontal Horizontal Report No. ENS2306120066W00501R Page 39 of 41 Ver.1.0 8.5 POWER LINE CONDUCTED EMISSIONS 8.5.1 Applicable Standard According to FCC Part 15.207(a) 8.5.2 Conformance Limit Conducted Emission Limit Frequency(MHz) Quasi-peak Average 0.15-0.5 66-56 56-46 0.5-5.0 56 46 5.0-30.0 60 50 Note: 1. The lower limit shall apply at the transition frequencies 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50MHz. 8.5.3 Test Configuration Test according to clause 6.3 conducted emission test setup 8.5.4 Test Procedure The EUT was placed on a table which is 0.8m above ground plane. Maximum procedure was performed on the highest emissions to ensure EUT compliance. Repeat above procedures until all frequency measured were complete. 8.5.5 Test Results N/A Report No. ENS2306120066W00501R Page 40 of 41 Ver.1.0 8.6 ANTENNA APPLICATION 8.6.1 Antenna Requirement Standard FCC CRF Part15.203 FCC 47 CFR Part 15.247 (b) RSS-Gen Section 6.8 RSS-247 Section 5.4 Requirement An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. If transmitting antennas of directional gain greater than 6dBi are used, the power shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6dBi. The applicant for equipment certification shall provide a list of all antenna types that may be used with the transmitter, where applicable (i.e. for transmitters with detachable antenna), indicating the maximum permissible antenna gain (in dBi) and the required impedance for each antenna. The test report shall demonstrate the compliance of the transmitter with the limit for maximum equivalent isotropically radiated power (e.i.r.p.) specified in the applicable RSS, when the transmitter is equipped with any antenna type, selected from this list. If the transmitter employs an antenna system that emits multiple directional beams, but does not emit multiple directional beams simultaneously, the total output power conducted to the array or arrays that comprise the device (i.e. the sum of the power supplied to all antennas, antenna elements, staves, etc., and summed across all carriers or frequency channels) shall not exceed the applicable output power limit. However, the total conducted output power shall be reduced by 1 dB below the specified limits for each 3 dB that the directional gain of the antenna/antenna array exceeds 6 dBi. The directional antenna gain shall be computed as the sum of 10 log (number of array elements or staves) plus the directional gain of the element or stave having the highest gain. 8.6.2 Result PASS. Note: Antenna use a permanently attached antenna which is not replaceable. Not using a standard antenna jack or electrical connector for antenna replacement The antenna has to be professionally installed (please provide method of installation) Please refer to the attached documentInternal Photos to show the antenna connector. --------- END OF REPORT -------- Report No. ENS2306120066W00501R Page 41 of 41 Ver.1.0WPS 文字