KLLOQUE K10 B Smart Lock User Manual

Notes:

1. Before installation, please check and confirm all parts and components are complete. If any part is missing, contact customer service by email at service@klloque.com.
2. This lock has a built-in rechargeable battery. Before installation, please recharge the lock for at least 3 hours.
3. Please use a manual screwdriver for installation; an electric screwdriver is not recommended.
4. If fingerprint recognition fails 5 times, the module will be deactivated for 2 minutes. Please retry after 2 minutes.
5. If the door knob appears damaged or does not operate properly, please contact customer service for further assistance at service@klloque.com.

Charging Information

ATTN: Please use a USB-A to Type-C cable for charging or emergency power supply, as shown in the figure.

(Diagram showing USB-A to Type-C cable with a checkmark and Type-C to Type-C cable with an 'X' mark)

Installation Guide

Packing List

• A: Exterior Knob (1 PC)
• B: Interior Knob (1 PC)
• C: Latch (1 PC)
• D: Strike Plate (1 PC)
• E: Strike Box (1 PC)
• F: Screw A (4 PCS)
• G: Screw B (2 PCS)
• H: Key (2 PCS)
• I: Pin (1 PC)
• J: USB-Type C cable (1 PC)
• K: User Manual (1 PC)

Tools Required

• Phillips Screwdriver
• Tape Measure

Prepare Door and Check Dimensions

Ensure door thickness is between 1 3/8" to 2 1/8" (35-54mm). Backset can be 2 3/4" (70mm) or 2 3/8" (60mm). The diameter of the door hole should be 2 1/8" (54mm), and the diameter of the latch hole should be 1" (25mm).

Install Latch and Strike

1. Hold the latch in front of the door hole so it is flush with the door edge.
2. Press the square-shaped hole and pull the latch to set the backset to 60mm (2-3/8") or 70mm (2-3/4") to fit your door hole.
3. Ensure the square-shaped hole is in the horizontal position.
4. Insert the latch into the door hole and tighten Screw A to fix it.
5. Install the strike box and strike plate with Screw A into the door frame.

Pull out the Interior Knob

As shown in the figure, insert the pin into the hole and separate the rosette from the Interior Knob. Use a screwdriver to remove Screw B.

(Diagram illustrating steps to remove the interior knob)

Install the Exterior Knob

Install the Exterior Knob onto the door with the rod bolts going through the circular holes on the Latch, and the spindle going through the square-shaped (center) hole.

(Diagram illustrating the installation of the exterior knob)

Install the Interior Knob

The "up" mark above the rosette should face upward. Install the rosette onto the door with the rod bolts aligning the circular holes and the spindle aligning the square-shaped (center) hole. Insert Screw B into the circular holes and tighten to secure the rosette.

Firstly, ensure the spindle bar is in the vertical position. Secondly, rotate the thumb turn to the circular mark. Lastly, insert the Interior Knob into the rosette by aligning the hole of the Interior Knob with the spindle bar and aligning the rectangular hole at the edge of the interior knob with the circular hole at the edge of the rosette.

(Diagrams illustrating the installation of the interior knob)

Operation Guide

Key to Unlock

Insert the key into the keyhole at the edge of the Exterior Knob, turn the key 120° to unlock, then turn the Exterior Knob to open the door.

Low Power Indication

When the buzzer beeps once and the fingerprint identification area flashes green then red, it indicates the need to recharge the lock. Connect a power bank to the Type-C interface on the knob for charging.

Restore the Factory Setting

Unlock the smart lock using the app or fingerprint. Rotate the thumb turn from the circular mark to the unlock sign on the left, then return it to the circular mark. Repeat this operation 5 times. Then, conduct the same operation towards the right for 5 times. You will hear a long beep, and the fingerprint identification area will flash green. All fingerprints will then be able to unlock the lock.

Modes

• Normal Mode: Rotate the thumb turn to the circular mark above the thumb turn. The door knob automatically locks in 5 seconds after unlocking with a fingerprint. Both members and administrators can unlock with their fingerprints.
• Passage Mode: Rotate the thumb turn to the unlock sign on the left. The door knob remains unlocked.
• Privacy Mode: Rotate the thumb turn to the lock sign on the right. Both members and administrators can unlock via the app. Only administrators' fingerprints can unlock the lock.

Indicator and Buzzer Status

Product Features

• ? Fingerprint Unlock
• ? APP Unlock
• ? Key Unlock
• ? Auto-Lock
• ? Privacy Mode
• ? Passage Mode
• ? History Log

This smart lock can be managed and controlled by the Smart Life app on your phone. Please refer to the following pages for app instructions.

App Guide

Scan the Smart Life QR Code to download the app or search "Smart Life" in the App Store (iOS) and Google Play (Android).

(QR Code for Smart Life App)

Account Registration

Register a new account (Email Address) or log in with an existing account.

(Screenshots of the app's login/registration interface)

Pair the Lock

Turn on your phone's Bluetooth and stay near the lock (within 3 meters). Click "Add Device" on the App.

(Screenshots of the app's pairing process)

Successful connection! You can click the edit icon ✏️ to rename the lock or click "Done" to complete the pairing.

APP Unlock/Lock

Unlock: Hold and drag the unlock icon ? to the lock icon ?.

Lock: Hold and drag the lock icon ? to the unlock icon ?.

(Screenshots of the app's unlock/lock interface)

Member Management & Fingerprint Input

Select "Member Management" and tap "+" to add/share/cancel members.

Press "Add" and follow the instructions to add fingerprints.

Warm tips:

• Please keep your fingers and the sensing area clean and dry before inputting your fingerprint.
• For improved fingerprint recognition for the elderly, children, or people with light fingerprints, create multiple fingerprint files and input them at different angles.
• For your privacy, your fingerprints will be stored only on the device.

(Screenshots of the app's member management and fingerprint input interface)

Create Smart Scenes

Select "Smart Scenes" on the screen. Then choose the scenes you prefer to set intelligent interactions.

(Screenshots of the app's smart scenes interface)

More

Choose "More" to turn on/off "Remote Unlock" and set up lock volume. Note: Remote unlocking requires a gateway connection.

(Screenshots of the app's 'more' settings)

Device Information Set Up

Press the product name to check and set up the relevant information.

(Screenshot of the app's device information screen)

Specifications

Technical Parameters

FAQ

Q: Why can't the door lock recognize my fingerprint well or fail to unlock with the App?

A: When recording fingerprints, place your clean and dry finger at different angles and positions to ensure a larger area is scanned. The elderly and children may not use their fingerprints effectively, so keep fingers clean before unlocking.

Q: If the batteries die, how can I open the door?

A: The smart door knob has a built-in rechargeable battery. You can use an emergency power supply to charge it through a USB A+Type C port or use the backup key to open the door.

Q: After installing the new lock, what should I do to pair and set it up?

A: This smart knob is controlled by the Bluetooth Smart Life app. Confirm that Bluetooth and Location permissions are enabled for the app. After authorization, touch the fingerprint sensor to wake up the smart lock. If two users manage one lock simultaneously via the app, only one user can connect to control it.

Q: Why is my Smart Lock low-powered?

A: Charge the lock for 3-4 hours before installing. When the low battery warning occurs (fingerprint unlocked, green light then flashing red light), it indicates the need for charging.

Q: What can I do if the smart knob locks me out after several incorrect inputs?

A: For user safety, if you enter the wrong fingerprint five times in a row, the lock enters security mode and stops accepting fingerprints. To exit this mode: 1. Unlock via app. 2. Unlock via backup key. 3. Wait for 2 minutes.

FCC WARNING

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: The equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

Customer Service

Please send an email to service@klloque.com.