Westinghouse Solar LED Wall Light with Motion Sensor

Installation

Tools Required

• Pencil
• Phillips-head Screwdriver
• Electric drill with drill bit size: Ø7.5mm (3/10 in.)

Hardware Included

• (A) Screw x 4
• (B) Wall Anchor x 4

Parts

• (C) Light Fixture x 2

Step 1: Marking the location

Mark the location where you want to mount the light fixture (Part C). Measure the width of two holes on the back of the light to align holes for the 2 screws (Part A) on the surface. The distance between the two holes is 5.12in. (130mm). Drill two holes.

Step 2: Mounting the light fixture

1. Insert the wall anchors (Part B) so they are flush with the surface.
2. Insert the screws (Part A) and leave at least 1/4in. (6.3mm) of the screws (Part A) outside of the surface for holding the light.
3. Mount the light (Part C) on the screws (Part A) by placing the keyholes on the back of the light over the screw heads.

Note: Light fixture will stay on for 30 seconds when triggered by motion delivering up to 2000 Lumens and revert back to standby mode delivering up to 50 lumens until motion is detected. For best performance, mount the light a minimum 6 feet (1.8 m) above the ground. Motion detection range is up to 20 feet (6 m), motion detection angle is up to 120°. Light fixtures use radio frequency technology to link, and light fixtures should not be greater than 90 feet (27 m) apart for linked function to work properly. When one light is triggered by motion, both lights will activate and deliver up to 2000 lumens. The package includes 2 lights. These 2 lights are factory linked, and can not be linked with more of the same type light or any other lights. If there are performance or quality issues, both units need to be replaced with another set.

Trouble Shooting

If light doesn't turn on, check the battery to ensure that it is making secure contact with the terminals. If this doesn't work, replace with a new battery.

Replacing the Battery

1. Slide the power switch to the "OFF" position.
2. Use a Phillips head screwdriver to remove the 8 screws holding the battery cover in place.
3. Replace old batteries with 2 new 3.7V, 2000 mAh lithium (18650) rechargeable batteries.
4. Replace the battery cover by aligning it properly and replacing the 8 screws removed earlier.
5. Slide the power switch to the "ON" position.
6. For optimal performance, allow light fixture to charge in full sunlight for 8-12 hours, to fully charge the battery.

FCC Warning

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment.

Notes: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.

RF Exposure: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Important Safety Information

WARNING: Do not dispose of lithium batteries in municipal waste stream or by fire as batteries may explode. Do not open, short circuit, or destroy batteries. Dispose of batteries in accordance with Local, State, and Federal regulations. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel cadmium, nickel metal hydride or lithium ion) batteries.

Contact Information

For additional help and information regarding installation, contact customer service at 1-844-551-0680, 8am-5pm, CST Monday - Friday customerservice@idctexas.com

(W) and Westinghouse are trademarks of Westinghouse Electric Corporation. Used under license by Sky Rich Star Limited. All Rights Reserved.