Instruction Manual for alphacool models including: RTX 4070Ti Eisblock Aurora Ventus with Backplate, RTX 4070Ti, Eisblock Aurora Ventus with Backplate, Ventus with Backplate, Backplate
Alphacool RTX 4070Ti ROG Strix 12G Gaming EN A Safety instructions Sicherheitshinweise Avis de sécurité DE Accessories B C D Digital guide Digitale Anleitung Guide digital Zubehör FR Accessoires E F G H I 1x 25x15x1mm Pad J 2x 40x15x1mm Pad K 1x 70x8x1mm Pad L 1x 110x8x1mm Pad M 1x 1x Thermal Grease Putty tool N O 4x EVA Washer P 4x M2x5mm Screw Q 1x 45x45x3mm GPU-Pad R 2x 40x15x3mm Pad 1x 81x8x3mm Pad 1x 110x8x3mm Pad 1x 25x15x3mm Pad 1x 20x8x3mm Pad 4x M2x11mm Screw 1x ARGB Adapter 1x Plug tool 2x G1/4 Plug EN Check compatibility and prepare graphics DE Kompatibilität prüfen und Grafikkarte FR Vérification de compatibilité et préparer la card vorbereiten carte graphique Check compatibility Before starting the cooler assembly, compare your card with the pictures in our configurator. To do so, visit https://www.hwconfig.com and search for your graphics card or cooler model. For a definitiv identification, you can also compare the PCB number. The cooler was designed for a special PCB layout. Occasionally, graphics card manufacturers may revise the design of their card slightly, causing the cooler not to fit on later models. During assembly, please make sure taller parts have enough space around them and that the cooler does not damage your graphics card. Kompatibilität prüfen Bevor Sie mit der Montage des Kühlers beginnen, vergleichen Sie Ihre Platine mit den Fotos in unserem Konfigurator. Besuchen Sie dafür https://www.hwconfig.com und suchen Sie nach Ihrem Grafikkarten- oder Kühlermodell. Zur eindeutigen Zuordnung kann dort auch die PCB Nummer verglichen werden. Der Kühler wurde für ein spezielles PCB Layout konstruiert. Es kommt vor, dass Grafikkartenhersteller über Revisionen den Aufbau leicht abändern und der Kühler auf spätere Modelle nicht mehr passt. Achten Sie auch bei der Montage darauf, dass hohe Bauteile frei liegen und der Kühler die Grafikkarte nicht beschädigt. Vérification de compatibilité Avant de commencer l'assemblage du refroidisseur comparez votre carte avec les images de notre configurateur. Pour ce faire, visitez https://www.hwconfig.com et cherchez votre carte graphique ou votre modèle de refroidisseur. Pour une identification précise, vous pouvez également comparer le numéro de la PCB. La refroidisseur a été conçu pour une disposition spéciale du PCB. Il est possible que le fabricant change des détails dans la disposition de ses composants lors d'une révision et que le bloc de refroidissement ne soit plus compatible. Veillez lors de l'installation au fait que les composants hauts ne touchent pas le bloc de refroidissement et que le bloc n'endommage pas la carte graphique. Alphacool International GmbH is not liable for Alphacool International GmbH haftet nicht bei Alphacool International GmbH n'est pas assembly errors occurring due to negligence, fahrlässigen Montagefehlern, wie die Wahl eines responsable ni des erreurs d'installation ni du such as selecting an incompatible cooler. inkompatiblen Kühlers. choix d'un refroidisseur incompatible. Prepare graphics card Put the hardware on an antistatic mat. Begin dismantling the original cooler. Depending on the structure of the cooler, remove the screws at the back of the card and carefully unhook the fan connector first. If the original cooler uses thermal glue, extreme care should be taken as you can easily damage parts. Pick up all the items carefully. Next, clean the hardware of thermal paste or pad residues with a solvent (e.g. isopropanol alcohol). Grafikkarte vorbereiten Legen Sie die Hardware auf eine antistatische Unterlage. Beginnen Sie mit der Demontage des Original-Kühlers. Je nach Aufbau des Kühlers sind zuerst die Schrauben des Lüfters zu entfernen und die Blenden zu lösen. Bei aufgeklebten Kühlern ist äußerste Sorgfalt geboten. Es können leicht Bauteile abgerissen werden. Heben Sie alle Einzelteile sorgfältig auf. Reinigen Sie anschließend die Hardware von Resten der Wärmeleitpaste oder Pads mit einem Lösemittel (z.B. Isopropanol-Alkohol). Préparer la carte graphique Posez le matériel sur un tapis antistatique. Commencez par le démontage du refroidisseur d'origine. Selon la configuration du radiateur les vis du ventilateur et les caches doivent être enlevés d'abord. S'il s'agit d'un refroidisseur collé il faut travailler très doucement. Sinon des composants peuvent s'arracher. Conservez tous les pièces soigneusement. Ensuite, nettoyer le matériel de résidus de la pâte thermique ou de pads avec un solvant (alcool isopropanol par ex.). EN DE Place thermal pads on cooling block Wärmeleitpads auf dem Kühlblock platzieren FR Placer les pads thermique sur le bloc EN DE FR Apply Thermal Grease Wärmeleitpaste auftragen Appliquer la pâte thermique EN DE FR Install PCB Installiere PCB Installer PCB EN Place thermal pads on PCB backside DE Wärmeleitpads auf die PCB Rückseite platzieren FR Placer les pads thermique sur le PCB au dos EN DE FR Mount PCI bracket and backplate PCI Slotblende und Backplate montieren Monter le couvercle PCI et la plaque arrière For the PCI bracket, use the original screws of the graphics card (2). Für die Slotblende die Originalschrauben der Grafikkarte nutzen (2). Pour le couvercle PCI, utiliser les vis d'origine de la carte graphique (2). EN DE FR Connect ARGB lighting ARGB Beleuchtung anschließen Connecter l'éclairage ARGB EN DE Screw in screw plugs with the tool Verschlussschrauben eindrehen FR Visser les vis de fermeture avec l'outil Need help? Alphacool International GmbH Marienberger Str. 1 D-38122 Braunschweig Germany Support: +49 (0) 531 28874-0 Fax: +49 (0) 531 28874 - 22 E-Mail: info@alphacool.com https://www.alphacool.com We care!dompdf 1.1.0 CPDF