Warranty – Ensoshisha
User Guide for ENCO models including: Ensoshisha Electronic hookah vaporizer, Ensoshisha, Electronic hookah vaporizer, hookah vaporizer, vaporizer
Ensō – Ensoshisha
File Info : application/pdf, 38 Pages, 12.22MB
DocumentDocument1 QUICK START GUIDE CHARGE Make sure your battery is charged. FILL Fill the glass tank up to the level indicator. PACK Pack your cup tightly but create airways with the poking tool. TUNE Set the thermodial on the lowest setting (180°) and let it heat up for 5-8 minutes. If vapor production is increase the temp by 15-30° increthe change to take effect. ENJOY Delight in tasty clouds. Scan the QR code to unlock how-to videos that will help you to master your quickly. 2 ENS PARTS A B C D E F H G I J K A Thermocap B Heating chamber C Leather strap D Mouthpiece E LED indicator F Vaporhose-stem G Thermodial H Vaporhose I Watershield J Dip tube K Glass water tank L Battery slot M Battery handle N Blowout valve L O M N P Speaker O P Q R Q USB-C slot R Mute/unmute button S Water level indicator S 3 ACCESSORY LIST 2 Ceramic cups 10 Disposable cups Blowout valve Rubber heat valve Silicone mouthpiece cover Silicone mouthpiece tip USB-C Charger brick USB-C charging cable Long Brush Short Brush wiping cloth ENS CLEANING TOOL VERSION 1.0 Scrub tool Cup removal tool ENS UPDATED CLEANING MULTI-TOOL ENS Multi-tool 4 BATTERY lever upwards and the battery will be able to be removed. charging cable to the charging adapter and plug it into the USB-C port on the back of the unit. As long as the battery is inserted, and you has a minimal charge you can use your Ens plugged in. BATTERY TIPS Please avoid prolonged exposure to direct sun- heating and may become defective. The battery life will vary based on the selected heat setting. At the recommended low setting heat settings may reduce battery life. A small LED indicator on the battery is blinking on is fully charged. Charging is fastest via the USB-C port on the battery and a full charge can take up to 3.5 hours. 5 WATER TANK to the water level indicator. Water level indicator 6 VAPORHOSE Connect the vaporhose to the by inserting one end of the hose into the vaporhose-stem. 7 PACKING For best results please remember to mix your tobacco well, since the juices tend to settle on the bottom of the container, leaving the top part considerably more dry. By mixing up the tobacco with the juices before packing it into your cup/bowl, you get an even juice/tobacco distribution thus ensuring a higher quality flavor and experience altogether. Pack the ceramic or disposable cup lightly with you preffered type of tobacco. Remove the thermocap to expose the heating chamber. Insert the already packed ceramic or disposable cup into the heating chamber. Place the thermocap back onto the top of the heating chamber. 8 DRAW-RESISTANCE Insert the rubber heat valce into the thermocap for a stronger draw-resistance (recommended for herb mode) 9 THERMODIAL indicator will turn on with an orange color. Thermodial To control the heat setting turn the thermodial. Lower Higher The temperature settings are as shown on the image below. Each gradation step is the equivalent of 5° Celsius. The temperature settings are shown on the LED indicator. The Higher the temp is set the closer the LED strips are to the middle. Lower temp Higher temp 10 TIPS & TRICKS Not all tobaccos are created equal. We recommend for users to start the perature change to take effect. Make sure to loosen the tobacco with the poking tool after packing the cups lightly to ensure proper air movement through the tobacco. Once the use the cup removal tool to remove any type of cup from the chamber since the MULTI-TOOL CUP REMOVAL TOOL Press the thermodial 3 times to activate the G-mode. The LED indicator will turn green. Press the thermodial 3 times LED light turns green WHAT IS THE DIFFERENCE BETWEEN REGULAR MODE AND G-MODE In regular mode, the temperature is being regulated by Enso's sophisticated heating algorithm. Features a 70°C+ pre-heat in a 5-minutes pre-heating program. In G-Mode the power distribution is more linear to counterbalance the cooling from more frequent draws. Features no extra heat in the 5-minutes pre-heating time. NOTE: G-Mode produces increased-intensity vapors at higher temperature settings. 11 CLEANING - with the scrub tool For easier cleaning empty the cups after each usage as soon as they have cooled down and are safe to touch. warm water for at least 30 minutes. Handle metal brushes with caution as they can cause scrub the inside of the cup by twisting the scrub tool. to fit inside the heating chamber. inside of the chamber by turning the scrub tool. For better 11 CLEANING - with the multi-tool For easier cleaning empty the cups after each usage as soon as they have cooled down and are safe to touch. warm water for at least 30 minutes. The ENS Multi-tool contains: - Cup removal tool - Poking tool - Ceramic cup scraper - Chamber scraper Use the chamber scraper on the Multi-tool to clean the heating chamber after each use. Just insert the scraper plate into the chamber and scrape the interior by rotating the plate. Use the cup scraper on the Multi-tool to clean the ceramic chamber after each use. Simply insert the scraper plate into the ceramic cup and scrape the interior by rotating the plate. To clean the vaporshaft use the long brush with warm water. Use the long brush to scrub with upwards and downwards motion. The blowoutvalve can be removed and replaced by a second vaporhose for double hose usage. It is recommended for the blowout valve to be taken out and rinsed with water and 1-2 uses. / outwards motion. The mouthpiece can be cleaned with the short brush. Clean the airpath tubes by inserting the short brush into each individual airpath. 12 DIP TUBE of the rubber housing. 13 WITH LOOSE-LEAF To use Ens with loose leaf, insert the screen mesh into the bottom of the ceramic cup and fill the cup with the desired quantity (up to 3 gr) of the leaf of your choice. The ceramic cup is ideal for medium to heroic doses so please enjoy responsibly. For loose-leaf vapers who prefer metal heating chambers to ceramic, there is the option of the gold plated herb cup (sold separately). To use the herb cup, insert the screen mesh into the bottom of the herb cup and fill the cup with the desired quantity (up to 1.5 gr) of the leaf of your choice. After filling the cup, simply insert the cup into the heating chamber of the Ens. Purchase the gold-plated herb cup at: www.ensoshisha.com/products/herb-cup Press the thermodial 3 times for G-Mode (the LED turns green) Press the thermodial 5 times for Blue-Mode WHAT IS THE DIFFERENCE BETWEEN REGULAR MODE, G-MODE AND BLUE MODE In regular mode, the temperature is being regulated by Enso's sophisticated heating algorithm Features a 70°C+ pre-heat in a 5-minutes pre-heating program. In G-Mode the power distribution is more linear to counterbalance the cooling from more frequent draws Features no extra heat in the 5-minutes pre-heating time. NOTE: G-Mode produces increased-intensity vapors at higher temperature settings. In Blue-Mode the thermodial is inactive so while the unit is set for Blue Mode the set temperature cannot be modified by rotating the dial. THANK YOU FOR CHOOSING ENS ! FOR ADDITIONAL QUESTIONS ABOUT ENS PLEASE VISIT US AT: e ns o s h is h a .c o m /s u p p o r t Secure your warranty and unlock exclusive perks Register quickly at ensoshisha.com/warranty or scan the QR code below. WARM REGARDS, THE EN TEAM.