Samsung Electronics Co Ltd SMA516U Mobile Phone A3LSMA516U A3LSMA516U sma516u
74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, Korea TEL: +82-31-645-6300 FAX: +82-31-645-6401 HAC T-COIL Test Report Applicant Name: SAMSUNG Electronics Co., Ltd. 129, Samsung-ro, Yeongtong-gu, Suwon-Si, Gyeonggido, 16677 Rep. of Korea Date of Issue: Jul. 03, 2020 Test Report No.: HCT-SR-2006-FC006-R1 Test Site: HCT CO., LTD. FCC ID Equipment Type: Application Type FCC Rule Part(s): Model Name: Additional Model Name: Date of Test: A3LSMA516U Mobile Phone Certification CFR §20.19 , ANSI C63.19-2011 SM-A516U SM-A516U1 05/06/2020 ~ 06/08/2020, 07/02/2020 ~ 07/03/2020 C63.19-2011 HAC Category T3 (T-COIL CATEGORY) This wireless portable device has been shown to be hearing-aid compatible under the above rated category, specified in ANSI/IEEE Std. C63.19-2011 and had been tested in accordance with the specified measurement procedures. Hearing-Aid Compatibility is based on the assumption that all production units will be designed electrically identical to the device tested in this report. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. Tested By Reviewed By Jung-Hun, Park Test Engineer SAR Team Certification Division Yun-jeang, Heo Technical Manager SAR Team Certification Division This report only responds to the tested sample and may not be reproduced, except in full, without written approval of the HCT Co., Ltd. F-TP22-03 (Rev.00) HCT CO., LTD. Report No: HCT-SR-2006-FC006-R1 REVISION HISTORY The revision history for this test report is shown in table. Revision No. 0 R1 Date of Issue Jun. 19, 2020 Jul. 03, 2020 Description Initial Release Revised Sec.12.9 This test results were applied only to the test methods required by the standard. The above Test Report is not related to the accredited test result by (KS Q) ISO/IEC 17025 and KOLAS(Korea Laboratory Accreditation Scheme), which signed the ILAC-MRA. F-TP22-03 (Rev.00) 2 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Table of Contents 1. Test Regulations .......................................................................................................................................... 4 2. ATTESTATION OF TEST RESULT OF DEVICE UNDER TEST .................................................................. 5 3. DEVICE UNDER TEST DESCRIPTION........................................................................................................ 6 4. Test Methodology ........................................................................................................................................ 7 5. Measuring Instrument Calibraion .............................................................................................................. 8 6. Measurement Uncertainty........................................................................................................................... 9 7. Test Procedures for all Technologies ...................................................................................................... 10 8. Audio Level and Gain Measurements...................................................................................................... 14 9 T-coil Measurement Criteria ...................................................................................................................... 16 10. Device Under Test.................................................................................................................................... 18 11. Air Interfaces and Operating Mode ........................................................................................................ 19 12. HAC (T-coil) Test Results ........................................................................................................................ 20 Attachment 1. HAC T-COIL Test Plots ......................................................................................................... 46 Attachment 2. HAC T-Coil Probe Certificates ........................................................................................... 263 F-TP22-03 (Rev.00) 3 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 1. Test Regulations The tests were performed according to the following regulations: Test Standard FCC 47 CFR §20.19 ANSI C63.19-2011 Test Method FCC CFR47 Part 20.19 ANSI C63.19 2011-version FCC KDB 285076 D01 HAC Guidance v05r01 FCC KDB 285076 D02 T Coil testing v03 F-TP22-03 (Rev.00) 4 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 2. ATTESTATION OF TEST RESULT OF DEVICE UNDER TEST Test Laboratory Company Name: Address: Telephone: Fax.: HCT Co., LTD 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, 17383, Rep. of Korea +82 31 645 6300 +82 31 645 6401 Attestation of SAR test result Applicant Name: SAMSUNG Electronics Co., Ltd. Model: SM-A516U Additional Model Name: SM-A516U1 EUT Type: Mobile Phone Application Type: Certification 2.1 Test Methodology The Tests document in this report were performed in accordance with ANSI C63.19-2011 method of Measurement of Compatibility between Wireless Communication Devices and Hearing Aids, FCC published KDB 285076 D01 HAC Guidance v05r01, FCC Published KDB285076 D03 HAC FAQ v01r01 and TCB Workshop updates . F-TP22-03 (Rev.00) 5 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 3. DEVICE UNDER TEST DESCRIPTION 3.1 DUT specification Device Wireless specification overview Band & Mode Operating Mode CDMA/EVDO BC10 Voice / Data CDMA/EVDO BC0 Voice / Data PCS CDMA/EVDO Voice / Data GSM850 Voice / Data GSM1900 Voice / Data WCDMA 850 Voice / Data WCDMA 1700 Voice / Data WCDMA 1900 Voice / Data LTE Band 2 (PCS) Voice / Data LTE Band 4 (AWS) Voice / Data LTE Band 5 (Cell) Voice / Data LTE Band 7 Voice / Data LTE Band 12 Voice / Data LTE Band 13 Voice / Data LTE Band 14 Voice / Data LTE Band 25 (PCS) Voice / Data LTE Band 26 (Cell) Voice / Data LTE Band 30 Voice / Data LTE TDD Band 38 Voice / Data LTE TDD Band 40 Voice / Data LTE TDD Band 41 Voice / Data LTE Band 66 (AWS) Voice / Data LTE Band 71 Voice / Data NR Band n2 (PCS) Voice / Data NR Band n5 (Cell) Voice / Data NR Band n41 Voice / Data NR Band n66 Voice / Data NR Band n71 Voice / Data U-NII-1 Voice / Data U-NII-2A Voice / Data U-NII-2C Voice / Data U-NII-3 Voice / Data 2.4 WLAN Voice / Data Bluetooth / LE 5.0 Data ANT+ Data NFC Data Tx Frequency 817.25 ~ 822.75 824.70 ~ 848.31 1 851.25 ~ 1 908.75 824.2 ~ 848.8 1 850.2 ~ 1 909.8 826.4 ~ 846.6 1 712.4 ~ 1 752.6 1 852.4 ~ 1 907.6 1 850.7 ~ 1 909.3 1 710.7 ~ 1 754.3 824.7 ~ 848.3 2 502.5 ~ 2 567.5 699.7 ~ 715.3 779.5 ~ 784.5 790.5 ~ 795.5 1 850.7 ~ 1 914.3 814.7 ~ 848.3 2 307.5 ~ 2 312.5 2 572.5 ~ 2 617.5 2 307.5 ~ 2 312.5 , 2 352.5 ~ 2 357.5 2 498.5 ~ 2 687.5 1 710.7 ~ 1 779.3 665.5 ~ 695.5 1 852.5 ~ 1 907.5 826.5 ~ 846.5 2 506.02 ~ 2 679.99 1 712.5 ~ 1 777.5 665.5 - 695.5 5 180 ~ 5 240 5 260 ~ 5 320 5 500 ~ 5 720 5 745 ~ 5 825 2 412 ~ 2 472 2 402 ~ 2 480 2 402 ~ 2 480 13.56 F-TP22-03 (Rev.00) 6 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 4. Test Methodology The tests documented in this report were performed in accordance with ANSI C63.19-2011 Methods of Measurement of Compatibility between Wireless Communications Devices and Hearing Aids and FCC published procedure KDB 285076 D01 HAC Guidance v05 IP v03 KDB 285076 D03 HAC FAQ v01 TCB workshop updates KDB 285076 D02 T-Coil testing for CMRS F-TP22-03 (Rev.00) 7 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 5. Measuring Instrument Calibraion The measuring equipment used to perform the tests documented in this report has been calibrated in accordance with the manufacturers' recommendations and is traceable to recognized national standards. Name of Equipment Manufacturer Type/Model Serial No. ABM Probe SPEAG AM1DV3 3050 Data Acquisition Electronics SPEAG DAE3 504 ABM Probe SPEAG AM1DV3 3049 ABM Probe SPEAG AM1DV3 3049 ABM Probe SPEAG AM1DV2 1013 Data Acquisition Electronics SPEAG DAE4 868 DAC Sound Devices USBPre 2 HB1318341009 Radio Communication Tester R & S CMW 500 167916 Radio Communication Tester R & S CMW 500 167918 Radio Communication Tester R & S CMW 500 127521 WCDMA, GSM Band are Tested using SN 3049 AM1DV3 Probe on 05/07/2020 Cal. Due Date 11/20/2020 02/26/2021 05/21/2020 05/26/2021 04/23/2021 09/04/2020 N/A 10/23/2020 04/17/2021 05/15/2021 F-TP22-03 (Rev.00) 8 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 6. Measurement Uncertainty Measurement Uncertainty for Audio Band Magnetic Measurement Error Description Probe Sensitivity Uncertainty Probe Div. values (±%) Dist. ci ABM1 ci ABM2 Std. Unc. ABM1 (±%) ABM2 (±%) ReFerence Level 3.00 N 1 1 1 3.00 3.00 AMCC Geometry 0.40 R 1.73 1 1 0.23 0.23 AMCC Current 1.00 R 1.73 1 1 0.58 0.58 Porbe Positioning during 0.10 R 1.73 1 1 0.06 0.06 Calibr. Noise Contribution 0.70 R 1.73 0.0143 1 0.01 0.40 Frequency Slope 5.90 R 1.73 0.1 1 0.34 3.41 Probe System Repeatability / Drift 1.00 R 1.73 1 1 0.58 0.58 Linearity / Dynamic Range 0.60 R 1.73 1 1 0.35 0.35 Acoustic Noise 1.00 R 1.73 0.1 1 0.06 0.58 Probe Angle 2.30 R 1.73 1 1 1.33 1.33 Spectral Processing 0.90 R 1.73 1 1 0.52 0.52 Integration Time 0.60 N 1.00 1 5 0.60 3.00 Field Disturbation 0.20 R 1.73 1 1 0.12 0.12 Test Signal Ref. Signal Spectral Response 0.60 R 1.73 0 1 0.00 0.35 Positioning Probe Positioning 1.90 R 1.73 1 1 1.10 1.10 Phantom Thickness 0.90 R 1.73 1 1 0.52 0.52 DUT Positioning 1.90 R 1.73 1 1 1.10 1.10 External Contributions RF Interference 0.00 R 1.73 1 0.3 0.00 0.00 Test Signal Variation 2.00 R 1.73 1 1 1.2 Combined Std. Uncertainty 4.1 (ABM field) Expanded Std. Uncertainty 8.1 (%) Notes for table N - Nomal R - Rectangular Div. - Divisor used to obtain standard uncertainty 1.2 6.1 12.3 F-TP22-03 (Rev.00) 9 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 7. Test Procedures for all Technologies 7.1 General Procedures C63.19-2011, Section 7 ANSI C63.19-2011, Section 7 This document describes the procedures used to measure the ABM (T-Coil) performance of the WD. In addition to measuring the absolute signal levels, the A-weighted magnitude of the unintended signal shall also be determined. In order to assure that the required signal quality is measured, the measurement of the intended signal and the measurement of the unintended signal must be made at the same location for all measurement positions. In addition, the RF field strength at each measurement location must be at or below that required for the assigned category. Measurements shall not include undesired properties from the WD's RF field; therefore, use of a coaxial connection to a base station simulator or non-radiating load may be necessary. However, even then with a coaxial connection to a base station simulator or non-radiating load there may still be RF leakage from the WD, which may interfere with the desired measurement. Pre-measurement checks should be made to avoid this possibility. All measurements shall be done with the WD operating on battery power with an appropriate normal speech audio signal input level given in Table 7.1. If the device display can be turned off during a phone call then that may be done during the measurement as well. Measurements shall be performed at two locations specified in A.3, with the correct probe orientation for a particular location, in a multistage sequence by first measuring the field intensity of the desired T-Coil signal (ABM1) that is useful to a hearing aid T-Coil. The undesired magnetic components (ABM2) must be measured at the same location as the desired ABM or T-Coil signal (ABM1), and the ratio of desired to undesired ABM signals must be calculated. For the perpendicular field location, only the ABM1 frequency response shall be determined in a third measurement stage. The flow chart in Figure 7.3 illustrates this three-stage, two orientation process. The following steps summarize the basic test flow for determining ABM1 and ABM2. These steps assume that a sine wave or narrowband 1/3 octave signal can be used for the measurement of ABM1. A validation of the test setup and instrumentation may be performed using a TMFS or Helmholtz coil. Measure the emissions and confirm that they are within the specified tolerance. Position the WD in the test setup and connect the WD RF connector to a base station simulator or a nonradiating load as shown in Figure 7.1 or Figure 7.2. Confirm that equipment that requires calibration has been calibrated, and that the noise level meets the requirements given in 7.3.1. The drive level to the WD is set such that the reference input level specified in Table 7.1 is input to the base station simulator (or manufacturer's test mode equivalent) in the 1 , 1/3 octave band. This drive level shall be used for the T-Coil signal test (ABM1) at f = 1 . Either a sine wave at 1025 Hz or a voice- like signal, band-limited to the 1 1/3 octave, as defined in 7.4.2, shall be used for the reference audio signal. If interference is found at 1025 Hz an alternative nearby reference audio signal frequency may be used.46 The same drive level will be used for the ABM1 frequency response measurements at each 1/3 octave band center frequency. The WD volume control may be set at any level up to maximum, provided that a signal at any frequency at maximum modulation would not result in clipping or signal overload. Determine the magnetic measurement locations for the WD device (A.3), if not already specified by the manufacturer, as described in 7.4.4.1.1 and 7.4.4.2. At each measurement location, measure and record the desired T-Coil magnetic signals (ABM1 at fi) as described in 7.4.4.2 in each individual ISO 266-1975 R10 standard 1/3 octave band. The desired audio band input frequency (fi) shall be centered in each 1/3 octave band maintaining the same drive level as determined in item c) and the reading taken for that band. Equivalent methods of determining the frequency response may also be employed, such as fast Fourier transform (FFT) analysis using noise excitation or inputoutput comparison using simulated speech. The fullband integrated or half-band integrated probe output, as specified in D.9, may be used, as long as the appropriate calibration curve is applied to the measured result, so as to yield an accurate measurement of the field magnitude. (The resulting measurement shall be an accurate measurement in dB A/m.) All measurements of the desired signal shall be shown to be of the desired signal and not of an undesired signal. This may be shown by turning the desired signal ON and OFF with the probe measuring the same F-TP22-03 (Rev.00) 10 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 location. If the scanning method is used the scans shall show that all measurement points selected for the ABM1 measurement meet the ambient and test system noise criteria in 7.3.1. At the measurement location for each orientation, measure and record the undesired broadband audio magnetic signal (ABM2) as specified in 7.4.4.4 with no audio signal applied (or digital zero applied, if appropriate) using A-weighting and the half-band integrator. Calculate the ratio of the desired to undesired signal strength (i.e., signal quality). Obtain the data from the postprocessor, SEMCAD, and determine the category that properly classifies the signal quality based on Table 8.5. Test Setup Diagram USB PC USB Audio Coil Out Out Coil In AMMI Probe In Audio In/Out Base Station ----- For Cal Gain Coil Monitor AMCC EUT Coil In 7.2 VoWiFi For PAG REUSE This device supports Wi-Fi calling (aka Voice over Wi-Fi or VoWiFi) which is an extended feature of the carriers CMRS service to offload VoLTE calls onto local area networks over WI-FI via the internet and subject to HAC assessment for phones with a HAC rating. HAC assessment for this feature is subject to Pre Approval Guidance. The set up for VoWiFi uses the Base station as described in section 7.1 with the exception that the reference audio level is set at -20dBm0. The reference level is calibrated using the standard call box calibration procedures with the exception of the -20dBm0 reference level being used (refer to section 8.4). An investigation was performed to determine worst case codec, bit rate and air interface configuration (refer to sections 12.5 and 12.6). F-TP22-03 (Rev.00) 11 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 7.3 Over the Top(OTT) For PAG REUSE This device supports VoIP via a preinstalled application that uses the Google Duo service, using OPUS as its only codec (refer to §11 for air interface details and §12.7 for codec bit rates). VoIP capabilities require HAC assessment when voice calls are supported over the cellular data connection via preinstalled VoIP applications and the assessment is subject to Pre-Approval Guidance procedures. The equipment is set up as shown below with a support device used to originate the call using the IP transport. The support device connects to the cloud-based Google Duo service via Wi-Fi access point and router, or RJ45. The DUT connects to the VoIP service via a cellular/unlicensed air interface to the call box and an Ethernet connection from call box to Internet. The various codec bit rate and air interface configurations are evaluated to determine the worst-case configuration (refer to §12.7). Test Setup configuration for OTT calls For the OTT call, the calibrated audio card within the CMW500 cannot be used so the AMMI is connected to an external Digital-Analog Converter (DAC) and the DAC is connected to the Support Device via USB. The test signal is sent from the DASY PC to the AMMI, from the AMMI to the DAC, from the DAC to the Support Device, and, via the VoIP call, to the DUT. F-TP22-03 (Rev.00) 12 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 As this test set up uses an external DAC between the AMMI's audio output and support device, the appropriate gain factor for the OTT call needs be determined. This is done by connecting the DAC between the AMMI Audio output and Coil input as shown below. Using the metering function on the DAC, the DAC gain is adjusted until the volume reaches 0 dBFS (3.14 dBm0 based on TIA/EIA 810-A). SPEAG's "TN-LK-05042018-C-T-Coil_Levels" document (Appendix E) steps E through H are then followed to determine the adjusted gain values as detailed in §8.5 so that the reference level is set to 23.14dB below full scale, i.e. at -20dBm0. A verification of the DAC's output is performed prior to testing. F-TP22-03 (Rev.00) 13 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 8. Audio Level and Gain Measurements 8.1 GSM Refer to the below table for the gains used to measure GSM. Signal Type Audio Level [dBm] Gain [dB] Gain [linear] Voice 1 -16.00 28.4 26.3 Voice 300 - 3 -19.00 35.11 8.2 W-CDMA Refer to the below table for the gains used to measure W-CDMA. Signal Type Audio Level [dBm] Gain [dB] 55.75 Gain [linear] Voice 1 -16.00 28.4 26.3 Voice 300 - 3 -19.00 8.3 CDMA Refer to the below table for the gains used to measure GSM. Signal Type Audio Level [dBm] 35.11 Gain [dB] 55.75 Gain [linear] Voice 1 -18.00 26.29 20.63 Voice 300 - 3 -19.00 35 55.85 8.4 VOLTE Refer to the below table for the gains used to measure VoLTE. The following software/firmware was used to simulate the VoLTE server for testing: Firmware V3.7.30 for LTE V3.7.20 for Audio VoLTE FDD #1 Chamber License Keys KS500 KS550 KA100 KA150 KAA20 KM050 KS104 Software Name LTE FDD R8 SIG BASIC LTE TDD R8 SIG BASIC IP APPL ENABLING IPv4 IP APPL ENABLING IPv6 IP APPL IMS BASIC DATA APPL MEAS EVS SPEECH CODEC Signal Type Audio Level [dBm] Gain [dB] Gain [linear] Voice 1 -16.00 28.4 26.3 Voice 300 - 3 -19.00 35.11 55.75 VoLTE TDD #9 Chamber Signal Type Audio Level [dBm] Gain [dB] Gain [linear] Voice 1 -16.00 27.93 24.92 Voice 300 - 3 -19.00 34.64 53.55 F-TP22-03 (Rev.00) 14 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 8.5 VOWi-Fi Refer to the below table for the gains used to measure VoWi-Fi. Firmware V3.7.40 for WLAN V3.7.20 for Audio License Keys KS650 KS651 KS656 KS657 KA100 KA150 KAA20 KM050 KS104 Software Name WLAN A/B/G SIG BASIC WLAN N SIG BASIC WLAN IEEE 802.11ac WLAN IEEE 802.11ax IP APPL ENABLING IPv4 IP APPL ENABLING IPv4 IP APPL IMS BASIC DATA APPL MEAS EVS SPEECH CODEC Signal Type Voice 1 Voice 300 - 3 Audio Level [dBm] -20.00 -20.00 Gain [dB] 24.34 34.05 Gain [linear] 16.48 50.05 8.6 Over the Top(OTT) For PAG REUSE For EDGE, HSPA, LTE and Wi-Fi the linear gain levels listed below were used. The results below are based on a reference input level of -20 dBm. To calibrate the DAC (refer §7.3 ), three. Way audio files (sine wave, 1 voice, and 300 to 3 voice) are sent from the DASY5 PC to the AMMI, then to the DAC. The Helmholtz resonator measures the field strength, which represents the AMMI to DAC input sensitivity. After determining the input sensitivity, the adjusted linear gain values can then be calculated. Signal Type Voice 1 Voice 300-3 Audio Level [dBm] -20.00 -20.00 Gain [dB] 26.11 35.82 Gain [linear] 20.21 61.5 F-TP22-03 (Rev.00) 15 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 9 T-coil Measurement Criteria 9.1 Frequency Respones The frequency response of the axial component of the magnetic field, measured in 1/3 octave bands, shall follow the response curve, over the frequency range 300 Hz to 3000 Hz. Figure 8.1 and Figure 8.2 provide the boundaries for the specified frequency. These response curves are for true field strength measurements of the T-Coil signal. Thus the 6 dB/octave probe response has been corrected from the raw readings. F-TP22-03 (Rev.00) 16 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 9.2 Signal to Noise This specifies the signal-to-noise quality requirement for the intended T-Coil signal from a WD. The worst signal to noise of the two T-Coil signal measurements, as determined in Clause 7, shall be used to determine the T-Coil mode category per Table 8.5. Only the RF immunity of the hearing aid is measured in T-Coil mode. It is assumed that a hearing aid can have no immunity to an interference signal in the audio band, which is the intended reception band for this mode. So, the only criterion that can be measured is the RF immunity in T-Coil Mode. This is measured using the same procedure as for the audio coupling mode and at the same levels as specified in 6.4. Category Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] Category T1 0 dB to 10 dB Category T2 10 dB to 20 dB Category T3 20 dB to 30 dB Category T4 > 30 dB Table 8.5- T-Coil signal-to-noise categories Measurement locations and reference plane to be used for the T-coil measurements. F-TP22-03 (Rev.00) 17 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 10. Device Under Test Normal operation Held to head Back Cover The Back Cover is not removable Test sample information S/N TDM0558H TDM0031H TDM0578H TDM0558H Notes T-coil Test T-coil Test T-coil Test T-coil Test F-TP22-03 (Rev.00) 18 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 11. Air Interfaces and Operating Mode Air Interface GSM W-CDMA (UMTS) CDMA LTE - FDD LTE TDD NR -FDD NR -TDD Wi-Fi BT Bands () 850 1900 GPRS/EDGE 850 1700 1900 HSPA 800 850 1900 1xEvDO 680(B 71) 700 (B12/13/17) 850 (B5/26) 1700 (B4/66) 1900 (B2/25) 2300 (B30) 2500 (B7) 2600 (B41)2 3600 (B48) 2600 (B38) 2300 (B40) 850 (n5) 1900 (n2) 1700 (n66) 680 (n71) 2600 (N41) 2450 5200 (U-NII-1) 5300 (U-NII-2A) 5500 (U-NII-2C) 5800 (U-NII-3) 2450 Type VO DT VO VD VO VO VO VD VD VD VD VD VD DT Type: VO: Legacy Cellular Voice Service DT: Digital Transport only (no voice) CMRS: Commercial Mobile Radio Service VD: IP Voice service over Digital Transport C63.19 Tested Yes Yes3 Yes Yes3 Yes Yes Yes Yes3 Simultaneous Transmitter Wi-Fi, BT Wi-Fi, BT Wi-Fi, BT Wi-Fi, BT Wi-Fi, BT Wi-Fi, BT Wi-Fi, BT Wi-Fi, BT Audio Codecs Evaluated EFR OPUS2 AMR-NB & AMR-WB OPUS2 EVRC-B & 8k-EVRC OPUS2 Yes1 Wi-Fi, BT AMR-NB, AMR- WB, EVS-NB, EVSWB & OPUS2 Yes1,3 Wi-Fi, BT AMR-NB, AMR- WB, EVS-NB, EVS-WB & OPUS2 Yes Wi-Fi, BT OPUS Yes Wi-Fi, BT OPUS Yes3 WWAN AMR-NB, AMR- WB, EVS-NB, EVS-WB & OPUS2 NA WWAN N/A Note: 1. Ref Lev in accordance with the July 2012 VoLTE interpretation 2. Ref Lev -20 dBm0 3. For PAG REUSE F-TP22-03 (Rev.00) 19 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 12. HAC (T-coil) Test Results 12.1 Codec Investigation An investigation between the various codec configurations (Low/High bit rates for Narrowband, Wideband) and specific parameters are documented (ABM1, ABM2, S+N/N, frequency response) to determine the worst-case bit rates for each voice service type. The table below compares the varying codec configurations. A codec investigation was performed on one band of each CDMA, GSM, W-CDMA, LTE FDD/TDD. The highlighted results below were determined to be the worst case codec configuration(s) for CDMA,GSM, W- CDMA and LTE. Codec Investigation Codec State AMR-NB (kbit/s) EVRC-B 8k-EVRC Orientation Band/ Channel ABM1 (dB/m) 1.93 3.85 ABM2 (dBA/m) S+N/N (dB) Freq. Resposne (dB) ABM1 (dB/m) -22.38 24.31 1.23 -5.50 -22.24 26.08 1.77 -7.44 z (Axial) CDMA/EVDO BC0 CH. 384 ABM2 (dBA/m) -29.49 -32.34 y (Transversal) S+N/N (dB) 23.99 24.9 F-TP22-03 (Rev.00) 20 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Codec State ABM1 (dB/m) ABM2 (dBA/m) S+N/N (dB) Freq. Resposne (dB) ABM1 (dB/m) ABM2 (dBA/m) S+N/N (dB) Codec Investigation AMR-NB (kbit/s) FR V1 HR V1 -3.11 -1.94 -30.58 -33.53 27.48 31.60 2 2 -14.44 -14.35 -42.80 -44.42 28.36 30.07 Orientation Band/ Channel z (Axial) GSM 850 CH.190 y (Transversal) Codec Investigation Codec State AMR-NB (kbit/s) 4.75 7.4 12.2 AMR-WB (kbit/s) 6.6 15.85 23.85 Orientation Band/ Bandwidth/ Channel ABM1 (dB/m) 2.54 2.73 2.62 -3.04 -1.98 -1.82 ABM2 (dBA/m) S+N/N (dB) Freq. Resposne (dB) ABM1 (dB/m) -46.50 49.03 2 -4.63 -46.64 49.38 2 -4.09 -46.34 48.96 2 -4.70 -45.98 42.95 2 -10.25 -45.83 43.84 2 -9.33 -46.05 44.23 2 -9.35 z (Axial) WCDMA Band II Rel.99 CH.9400 ABM2 (dBA/m) -46.36 -45.65 -46.28 -45.94 -45.99 -45.55 y (Transversal) S+N/N (dB) 41.74 41.56 41.58 35.69 36.66 36.20 F-TP22-03 (Rev.00) 21 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Codec Investigation Codec State AMR-NB (kbit/s) 4.75 7.4 12.2 AMR-WB (kbit/s) 6.6 15.85 23.85 Orientation Band/ Bandwidth/ Channel ABM1 (dB/m) 2.60 3.20 3.23 -2.77 -1.49 -1.62 ABM2 (dBA/m) -45.44 -45.78 S+N/N (dB) 48.04 48.98 Freq. Resposne(dB) 2 2 ABM1 (dB/m) -4.91 -4.46 -45.62 48.85 2 -4.56 -45.01 42.24 2 -44.90 -45.35 43.41 43.73 2 2 -10.29 -9.21 -9.18 z (Axial) LTE Band 25 CH.26365 20 BW QPSK RB 100/0 ABM2 (dBA/m) -45.13 -45.49 -45.27 -44.52 -44.01 -44.47 y (Transversal) S+N/N (dB) 40.22 41.02 40.71 34.24 34.80 35.30 Codec Investigation Codec State EVS-NB (kbit/s) 5.9 13.2 24.4 EVS-WB (kbit/s) 5.9 13.2 24.4 Orientation Band/ BandWidth/ Channel ABM1 (dB/m) 1.04 2.25 1.83 -2.38 -2.09 -2.56 ABM2 (dBA/m) -46.05 -45.93 -46.02 -45.82 -45.60 -46.00 S+N/N (dB) 47.09 48.17 47.85 43.43 43.51 43.45 Freq.Resposne(dB) 2 2 2 2 2 2 ABM1 (dB/m) -6.39 -4.91 -4.47 -10.59 -8.82 -9.23 z (Axial)) LTE Band 25 CH.26365 20 BW QPSK RB 100/0 ABM2 (dBA/m) -44.83 -44.98 -44.52 -45.95 -44.22 -44.66 y (Transversal) S+N/N (dB) 38.44 40.07 40.05 35.37 35.40 35.43 F-TP22-03 (Rev.00) 22 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Codec Investigation Codec State ABM1 (dB/m) AMR-NB (kbit/s) 4.75 7.4 12.2 2.44 1.87 2.53 AMR-WB (kbit/s) 6.6 15.85 23.85 -3.64 -2.31 -2.29 Orientation Band/ Bandwidth/ Channel ABM2 (dBA/m) -42.78 -42.02 S+N/N (dB) 45.23 43.89 Freq. Resposne(dB) 2 2 ABM1 (dB/m) -14.81 -10.88 -41.94 44.46 2 -10.85 -42.40 -42.49 -42.22 38.76 40.19 39.92 2 1.95 1.92 -16.60 -15.66 -15.71 z (Axial) LTE Band 41 CH.40620 20 BW QPSK RB 100/0 ABM2 (dBA/m) -53.52 -52.14 -50.57 -51.32 -51.53 -51.43 y (Transversal) S+N/N (dB) 38.71 41.26 39.71 34.72 35.87 35.72 Codec State Codec Investigation EVS-NB (kbit/s) EVS-WB (kbit/s) 5.9 13.2 24.4 5.9 13.2 24.4 Orientation Band/ BandWidth/ Channel ABM1 (dB/m) 1.21 2.40 2.41 -7.82 -2.02 -2.39 ABM2 (dBA/m) -45.49 -45.01 -45.33 -44.48 -43.45 -44.45 S+N/N (dB) 46.70 47.40 47.74 36.66 41.42 42.06 Freq.Resposne(dB) 2 2 2 2 2 1.84 ABM1 (dB/m) -11.46 -14.83 -10.64 -21.06 -15.51 -15.36 z (Axial)) LTE Band 41 CH.40620 20 BW QPSK RB 100/0 ABM2 (dBA/m) -52.76 -53.85 -51.39 -51.58 -51.28 -50.96 y (Transversal) S+N/N (dB) 41.30 39.02 40.75 30.52 35.77 35.60 F-TP22-03 (Rev.00) 23 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 12.2 TDD Configuration LTE TDD Uplink-Downlink Configuration Investigation for VoLTE over IMS An investigation was performed to determine the worst-case Uplink-Downlink configuration for VoLTE over IMS T-Coil testing. The effects of UL-DL configuration were found to be independent of band and bandwidth; therefore, only one band and bandwidth were used for this investigation. Per 3GPP TS 36.211, the total frame length for each TDD radio frame of length Tf = 307200 · Ts = 10 ms, where Ts is a number of time units equal to 1/(15000 x 2048) seconds. Additionally, each radio frame consists of 10 subframes, each of length 30720 · Ts = 1 ms, and subframes can be designated as uplink (U), downlink (D), or special subframe (S), depending on the Uplink-Downlink configuration as indicated in Table 4.2-2 of 3GPP TS 36.211. In the transmission duty factor calculation, the special subframe configuration with the shortest UpPTS duration within the special subframe is used and will be applied for measurement. From 3GPP TS 36.211 Table 4.2-1, the shortest UpPTS is 2192 · Ts which occurs in the normal cyclic prefix and special subframe configuration 4. See table below outlining the calculated transmission duty cycles for each Uplink-Downlink configuration: Uplink-Downlink Configurations for Type 2 Frame Structures Downlink-to- Subframe number Calculated Uplink-downlink Uplink Switch- Transmission configuration point periodicity 0 1 2 3 4 5 6 7 8 9 Duty Cycle (%) 0 5 ms D S U U U D S U UU 61.4% 1 5 ms D S U U D D S U UD 41.4% 2 5 ms D S U D D D S U DD 21.4% 3 10 ms D S U U U D D D DD 30.7% 4 10 ms D S U U D D D D DD 20.7% 5 10 ms D S U D D D D D DD 10.7% 6 5 ms D S U U U D S U UD 51.4% Power Class 3 Uplink-Downlink Configuration Investigation VoLTE over IMS was evaluated with the following rado configuration channel 40620, 20MHz BW, QPSK, 100RB, 0Offset. all configurations (0-6) are supported. The configuration which resulted in the worst z (Axial) SNR was used for full testing. Uplink-Downlink configuration 0 was used as the worst-case configuration for VoLTE over IMS T-Coil testing. See table below for the SNR comparison between each Uplink-Downlink configuration: VoLTE over IMS SNNR by UL-DL Configuration Frequency [MHz] 2593.0 2593.0 2593.0 2593.0 2593.0 2593.0 2593.0 2593.0 2593.0 2593.0 2593.0 2593.0 2593.0 2593.0 Bandwidth RB RB UL-DL ABM1 Channel [MHz] Modulation Size Offset Configuration [dB(A/m)] 40620 20 QPSK 100 0 0 -7.82 40620 20 QPSK 100 0 1 -4.04 40620 20 QPSK 100 0 2 -6.73 40620 20 QPSK 100 0 3 -3.70 40620 20 QPSK 100 0 4 -4.00 40620 20 QPSK 100 0 5 -5.14 40620 20 QPSK 100 0 6 -7.36 40620 20 QPSK 100 0 0 -21.06 40620 20 QPSK 100 0 1 -18.27 40620 20 QPSK 100 0 2 -16.73 40620 20 QPSK 100 0 3 -17.11 40620 20 QPSK 100 0 4 -17.64 40620 20 QPSK 100 0 5 -18.36 40620 20 QPSK 100 0 6 -19.56 ABM2 [dB(A/m)] -44.48 -39.79 -43.71 -40.04 -44.74 -45.83 -45.02 -51.58 -49.62 -51.21 -51.76 -51.77 -51.47 -50.72 Orientation z (Axial) Freq. Response (dB) 2 1.93 2 1.92 1.97 1.93 1.8 y (Transversal) SNR [dB] 36.66 35.74 36.99 36.34 40.75 40.70 37.66 30.52 31.35 34.48 34.65 34.12 33.11 31.13 Per the investigations above, UL-DL Configuration 0 was used to evaluate VoLTE over IMS F-TP22-03 (Rev.00) 24 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 12.3 Air Interface Investigation Use the worst-case codec test and document a limited set of bands/modulations/channels/bandwidth. Observe the effect of changing the band and bandwidth to ensure that there are no unexpected variations. GSM / W-CDMA (UMTS) Mode Ch. Freq. CH.128 824.2 Orientation z(Axial) y(Transversal) ABM1 dB (A/m) 0.44 -10.36 ABM2 dB (A/m) -30.76 -42.60 Ambient Noise dB(A/m) -46.97 -46.84 GSM 850 Voice Coder Speech Codec: FR V1 CH.190 836.6 CH.251 848.8 z(Axial) y(Transversal) z(Axial) y(Transversal) GSM 1900 Voice Coder Speech Codec: FR V1 CH.661 1880.0 z(Axial) y(Transversal) W-CDMA Band IV Voice AMR WB Codec: 6.6 kbit/s CH.1412 z(Axial) 1732.4 y(Transversal) W-CDMA Band II Voice AMR WB Codec:6.6 kbit/s CH.9400 z(Axial) 1880.0 y(Transversal) CH.4132 z(Axial) 826.4 y(Transversal) W-CDMA Band V Voice AMR WB Codec: 6.6 kbit/s CH.4183 z(Axial) 836.6 y(Transversal) CH.4233 z(Axial) 846.6 y(Transversal) -3.11 -14.44 0.70 -10.77 1.53 -10.54 -3.04 -10.25 -3.11 -10.40 -3.12 -10.33 -3.11 -10.53 -5.26 -10.06 -30.58 -42.80 -32.72 -43.32 -36.95 -45.04 -45.98 -45.94 -46.16 -46.18 -46.16 -45.72 -46.23 -45.90 -46.25 -45.92 -46.97 -46.84 -46.97 -46.84 -46.97 -46.84 -46.97 -46.84 -46.97 -46.84 -46.97 -46.84 -46.97 -46.84 -46.97 -46.84 Freq. Response (dB) ABMSNR (dB) TRating Plot No. 2 31.20 T4 32.25 T4 2 27.48 T3 1/ 2 28.36 T3 3 2 33.42 T4 32.55 T4 2 38.48 T4 4/ 5 34.50 T4 6 2 42.95 T4 7/ 8 35.69 T4 9 2 43.04 T4 10/ 11 35.77 T4 12 2 43.04 T4 35.39 T4 2 43.12 T4 13/ 14 35.37 T4 15 2 40.99 T4 35.87 T4 F-TP22-03 (Rev.00) 25 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Air Interface Investigation(Contiued) Mode: Ch. Freq. BW/ RB BW Modulation Config. LTE-FDD Orientation ABM1 ABM2 dB(A/m) dB(A/m) z(Axial) -3.28 -44.49 1/0 y(Transversal) -10.52 -43.86 Ambient Noise dB(A/m) -46.42 -46.08 Freq. Response (dB) ABM SNR TRating Plot No. (dB) 2 41.21 T4 33.34 T4 z(Axial) -2.94 -44.20 -46.42 1/49 y(Transversal) -10.52 -43.86 -46.08 2 41.26 T4 33.34 T4 z(Axial) -2.79 -44.26 -46.42 1/99 y(Transversal) -10.55 -43.97 -46.08 2 41.47 T4 33.42 T4 z(Axial) -3.09 -45.01 -46.42 QPSK 50/0 y(Transversal) -10.51 -44.08 -46.08 2 41.92 T4 33.57 T4 20 z(Axial) -2.73 -45.31 -46.42 50/25 y(Transversal) -10.66 -44.15 -46.08 2 42.58 T4 33.50 T4 z(Axial) -2.82 -45.06 -46.42 50/49 y(Transversal) -10.43 -44.09 -46.08 2 42.24 T4 33.66 T4 LTE Band 25 Voice CH.26365 AMR 1882.5 WB Codec: 6.6 kbit/s z(Axial) -2.77 100/0 y(Transversal) -10.29 z(Axial) -2.70 16QAM 1/0 y(Transversal) -13.49 z(Axial) -2.45 64QAM 1/0 y(Transversal) -12.38 -45.01 -44.52 -41.14 -45.04 -41.96 -44.43 -46.42 -46.08 -46.42 -46.08 -46.42 -46.08 2 42.24 T4 34.24 T4 2 38.44 T4 16/ 17 31.54 T4 18 2 39.51 T4 32.05 T4 15 z(Axial) -2.42 -41.94 -46.42 1/0 y(Transversal) -13.38 -45.17 -46.08 2 39.53 T4 31.79 T4 10 z(Axial) -2.48 -41.49 -46.42 1/0 y(Transversal) -12.45 -44.44 -46.08 2 39.00 T4 31.99 T4 z(Axial) -2.65 -44.01 -46.42 5 16QAM 1/0 y(Transversal) -10.49 -43.88 -46.08 2 41.36 T4 33.39 T4 3 z(Axial) -2.82 -44.60 -46.42 1/0 y(Transversal) -10.19 -44.08 -46.08 2 41.78 T4 33.90 T4 1.4 z(Axial) -3.24 -43.55 -46.42 1/0 y(Transversal) -10.27 -44.13 -46.08 2 40.31 T4 33.86 T4 F-TP22-03 (Rev.00) 26 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Air Interface Investigation(Contiued) LTE-FDD Mode LTE Band 7 Voice AMR WB Codec: 6.6 kbit/s Ch. Freq. CH.21100 2535 Band width BW/ Mode RB Config . Orientation Ambient ABM1 ABM2 Noise dB(A/m) dB(A/m) dB(A/m) z(Axial) -2.61 -43.34 -46.42 20 16QAM 1/0 y(Transversal) -12.42 -45.47 -46.08 LTE Band 12 Voice AMR WB Codec: 6.6 kbit/s CH.23095 707.5 10 16QAM 1/0 z(Axial) -2.81 -35.85 -46.42 y(Transversal) -13.36 -43.76 -46.08 LTE Band 13 Voice AMR WB Codec: 6.6 kbit/s CH.23230 782 10 16QAM 1/0 z(Axial) -2.71 -41.75 -46.42 y(Transversal) -10.12 -41.82 -46.08 LTE Band 14 Voice AMR WB Codec: 6.6 kbit/s CH.23330 793 10 16QAM 1/0 z(Axial) -4.58 -41.70 -46.42 y(Transversal) -13.70 -45.20 -46.08 LTE Band 26 Voice AMR WB Codec: 6.6 kbit/s CH.26865 831.5 15 16QAM 1/0 z(Axial) -3.51 -36.41 -46.42 y(Transversal) -13.32 -43.24 -46.08 LTE Band 30 Voice AMR WB Codec: 6.6 kbit/s CH.27710 2310 10 16QAM 1/0 z(Axial) -3.90 -43.77 -46.42 y(Transversal) -12.43 -44.60 -46.08 LTE Band 66 Voice AMR WB Codec: 6.6 kbit/s CH.132322 1745 20 16QAM 1/0 z(Axial) -3.46 -43.06 -46.42 y(Transversal) -11.99 -44.01 -46.08 LTE Band 71 Voice AMR WB Codec: 6.6 kbit/s CH.133322 683 20 16QAM 1/0 z(Axial) -5.42 -43.08 -46.42 y(Transversal) -13.44 -43.63 -46.08 Freq. Response (dB) 2 2 2 2 2 2 2 2 LTE Band 26 CH.26765 821.5 15 16QAM 1/0 z(Axial) -5.34 -42.12 -46.42 y(Transversal) -12.04 -42.25 -46.08 2 Voice AMR WB Codec: 6.6 kbit/s CH.26965 841.5 15 16QAM 1/0 z(Axial) -5.46 -43.71 -46.42 y(Transversal) -13.18 -44.23 -46.08 2 ABM T- Plot SNR Rating No. (dB) 40.73 T4 19/ 20 33.05 T4 21 33.04 T4 22/ 23 30.40 T4 24 39.04 T4 25/ 26 31.70 T4 27 37.12 T4 28/ 29 31.50 T4 30 32.90 T4 31/ 32 29.92 T3 33 39.87 T4 34/ 35 32.17 T4 36 39.60 T4 37/ 38 32.02 T4 39 37.67 T4 40/ 41 30.19 T4 42 36.78 T4 30.21 T4 38.24 T4 31.05 T4 F-TP22-03 (Rev.00) 27 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Air Interface Investigation(Contiued) Mode Ch. Freq. BW BW/ Modulation RB Config. LTE-TDD Orientation ABM1 dB(A/m) z(Axial) -7.82 1/0 y(Transversal) -14.55 z(Axial) -4.45 1/49 y(Transversal) -21.09 z(Axial) -4.98 1/99 y(Transversal) -19.31 z(Axial) -4.33 QPSK 50/0 y(Transversal) -17.01 20 z(Axial) -5.59 50/25 y(Transversal) -12.75 LTE Band 41 Voice EVS-WB CH.40620 2593 Codec: 5..9 kbit/s z(Axial) -7.17 50/49 y(Transversal) -19.53 z(Axial) -7.82 100/0 y(Transversal) -21.06 z(Axial) -6.48 16QAM 1/49 y(Transversal) -20.95 z(Axial) -7.76 64QAM 1/49 y(Transversal) -11.76 15 z(Axial) -11.88 1/36 y(Transversal) -15.27 z(Axial) -7.87 10 QPSK 1/24 y(Transversal) -13.38 5 z(Axial) -9.89 1/12 y(Transversal) -23.49 ABM2 dB(A/m) Ambient Noise dB(A/m) Freq. Response (dB) -38.09 -55.70 2.0 -46.74 -55.92 -37.12 -55.70 2.0 -49.27 -55.92 -36.80 -55.70 2.0 -48.62 -55.92 -38.58 -55.70 2.0 -50.47 -55.92 -38.06 -55.70 2.0 -55.54 -55.92 -38.31 -55.70 2.0 -50.56 -55.92 -44.48 -55.70 2.0 -51.58 -55.92 -37.71 -55.70 1.75 -50.51 -55.92 -37.73 -55.70 2.0 -40.47 -55.92 -40.61 -55.70 1.78 -42.54 -55.92 -36.87 -55.70 1.63 -42.50 -55.92 -36.87 -55.70 1.99 -50.04 -55.92 ABM SNR (dB) 30.27 TRating Plot No. T4 32.19 T4 32.68 T4 28.19 T3 31.81 T4 29.31 T3 34.25 T4 33.46 T4 32.47 T4 42.78 T4 31.14 T4 31.04 T4 36.66 T4 30.52 T4 31.23 T4 29.57 T3 29.97 T3 28.72 T3 28.74 T3 27.27 T3 29.00 T3 29.12 T3 26.98 T3 26.55 T3 F-TP22-03 (Rev.00) 28 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Mode Ch. Freq. BW BW/ RB Modulation Config. Orientation ABM1 ABM2 dB(A/m) dB(A/m) Ambient Noise dB(A/m) Freq. Response (dB) LTE Band 38 Voice EVS-WB Codec: 5..9kbit/s CH.38000 2595 5 QPSK 1/12 z(Axial) y(Transversal) -6.67 -19.76 -35.23 -46.79 -55.70 -55.92 1.69 LTE Band 40 Voice EVS-WB Codec: 5..9kbit/s CH.38750 2310 5 QPSK 1/12 z(Axial) y(Transversal) -9.44 -15.88 -37.16 -43.18 -55.70 -55.92 1.86 LTE Band 40 Voice EVS-WB Codec: 5..9kbit/s CH.39200 2355 5 QPSK 1/12 z(Axial) y(Transversal) -10.49 -16.44 -39.15 -43.76 -55.70 -55.92 1.62 CH.39675 2498.5 5 QPSK 1/24 z(Axial) y(Transversal) -4.25 -15.77 -34.57 -42.64 -55.70 -55.92 1.94 LTE Band 41 CH.40148 2545.8 5 QPSK 1/24 z(Axial) y(Transversal) -10.98 -18.82 -39.25 -45.29 -55.70 -55.92 1.82 Voice EVS-WB Codec: 5..9kbit/s CH.41093 2640.3 5 QPSK 1/24 z(Axial) y(Transversal) -8.43 -18.09 -35.09 -42.78 -55.70 -55.92 2.0 CH.41565 2687.5 5 QPSK 1/24 z(Axial) y(Transversal) -8.92 -17.72 -33.65 -43.02 -55.70 -55.92 1.81 ABM SNR (dB) 28.56 27.03 27.72 27.30 28.67 27.32 30.33 26.87 28.27 26.47 26.67 24.69 24.73 25.30 T- Plot Rating No. T3 43/ 44 T3 45 T3 46/ 47 T3 48 T3 49/ 50 T3 51 T4 T3 T3 T3 T3 52/ 53 T3 54 T3 T3 F-TP22-03 (Rev.00) 29 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 12.4 VoWi-Fi Codec Investigation An investigation between the various codec configurations (Low/High bit rates for Narrowband, Wideband) and specific parameters are documented (ABM1, ABM2, S+N/N, frequency response) to determine the worst-case bit rates for each voice service type. The table below compares the varying codec configurations. A codec investigation was performed for each Wi-Fi 2.4 and 5. The highlighted results below were determined to be the worst case codec configuration(s) for Wi-Fi 2.4 and 5 . Codec Investigation Codec State ABM1 (dB/m) ABM2 (dBA/m) S+N/N (dB) Freq. Resposne(dB) ABM1 (dB/m) ABM2 (dBA/m) S+N/N (dB) AMR-NB (kbit/s) 4.75 -0.15 -40.43 40.28 2.0 -10.22 -48.06 37.85 7.4 0.87 -40.59 41.46 2.0 -5.61 -43.38 37.77 12.2 -0.08 -40.98 40.90 2.0 -5.60 -43.58 37.98 AMR-WB (kbit/s) 6.6 15.85 23.85 Orientation Band/ Bandwidth/ Channel -8.2 -5.97 -6.3 -41.35 33.16 2.0 -18.29 -47.63 29.34 -40.05 34.08 1.91 -13.11 -43.43 30.32 -39.84 33.54 1.88 -17.33 z (Axial) 802.11b CH.6 2437 DSSS 1 Mbps -47.66 y (Transversal) 30.33 Codec State ABM1 (dB/m) ABM2 (dBA/m) S+N/N (dB) Freq.Resposne(dB) ABM1 (dB/m) ABM2 (dBA/m) S+N/N (dB) Codec Investigation EVS-NB (kbit/s) EVS-WB (kbit/s) 5.9 0.01 -43.12 43.13 -2.15 -10.32 -51.53 41.21 13.2 1.51 -43.69 45.20 2.0 -8.50 -51.30 42.80 24.4 0.74 -43.94 44.68 2.0 -6.07 -48.32 42.25 5.9 -10.60 -43.86 33.26 2.0 -21.72 -50.39 28.67 13.2 -5.68 -44.00 38.32 1.85 -12.30 -48.56 36.26 24.4 -6.07 -43.60 37.54 1.72 -12.66 -47.72 35.06 Orientation Band/ BandWidth/ Channel z (Axial) 802.11b CH.6 2437 DSSS 1 Mbps y (Transversal) F-TP22-03 (Rev.00) 30 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Codec Investigation AMR-NB (kbit/s) Codec State ABM1 (dB/m) ABM2 (dBA/m) S+N/N (dB) Freq. Resposne(dB) ABM1 (dB/m) ABM2 (dBA/m) S+N/N (dB) 4.75 0.59 -42.82 43.41 2.0 -5.81 -46.70 40.89 7.4 2.69 -43.52 46.22 2.0 -6.95 -49.93 42.99 12.2 2.34 -43.85 46.18 2.0 -7.21 -50.00 42.79 AMR-WB (kbit/s) 6.6 15.85 23.85 Orientation Band/ Bandwidth/ Channel -5.88 -4.68 -4.62 -43.61 -43.66 -43.59 37.73 38.97 38.97 z (Axial) 802.11a CH.40 2.0 -18.30 -52.64 34.34 1.92 -13.89 -49.69 35.80 1.84 -13.89 5200 BPSK 6 Mbps -49.85 y (Transversal) 35.96 Codec State ABM1 (dB/m) ABM2 (dBA/m) S+N/N (dB) Freq.Resposne(dB) ABM1 (dB/m) ABM2 (dBA/m) S+N/N (dB) Codec Investigation EVS-NB (kbit/s) EVS-WB (kbit/s) 5.9 1.76 -43.32 45.08 2.0 -4.67 -45.82 41.15 13.2 1.84 -43.55 45.39 2.0 -6.58 -49.93 43.35 24.4 2.35 -43.73 46.08 2.0 -9.84 -52.27 42.44 5.9 -8.13 -43.21 35.08 1.98 -21.43 -49.89 28.45 13.2 -4.18 -42.96 38.78 1.85 -13.32 -49.02 35.71 24.4 -5.90 -41.98 36.08 1.78 -16.92 -52.34 35.41 Orientation Band/ BandWidth/ Channel z (Axial) 802.11a CH.40 5200 BPSK 6 Mbps y (Transversal) F-TP22-03 (Rev.00) 31 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 12.5 VoWi-Fi Air Interface Investigation Using the data from §9.4, further testing was performed on the remaining 802.11 modes. The objective of these measurements is to ensure that changing the modulation, bandwidth, and data rate, whilst using the worst case codec configuration measured in §9.4, yields no unexpected variations. Moe Ch. Freq. BW BW/ Modeulation Orientation ABM1 dB(A/m) ABM2 dB(A/m) Ambient Freq. Noise dB Response (A/m) (dB) DSSS z(Axial) -10.60 -43.86 -57.87 2.0 1 Mbps y(Transversal) -21.72 -50.39 -56.63 CH.6 2437 CCK z(Axial) -11.58 -46.63 -57.87 1.95 5.5 Mbps y(Transversal) -16.76 -46.09 -56.63 802.11b Voice EVS-WB Codec: 5.9 kbit/s 20 CCK 11 Mbps z(Axial) -11.69 y(Transversal) -18.51 -44.86 -48.91 -57.87 -56.63 1.57 CH.1 2412 DSSS z(Axial) -9.46 -42.62 -57.87 1.93 1 Mbps y(Transversal) -19.20 -44.58 -56.63 CH.11 2462 DSSS z(Axial) -11.30 -43.06 -57.87 1.97 1 Mbps y(Transversal) -16.29 -46.85 -56.63 802.11g Voice EVS-WB Codec: 5.9 kbit/s CH.6 2437 20 QPSK 6 Mbps z(Axial) -10.47 y(Transversal) -15.70 -45.51 -47.28 -57.87 -56.63 1.85 802.11n HT20 Voice AMR-WB Codec: 5.9 kbit/s CH.6 2437 20 16QAM MCS 3 z(Axial) -9.74 y(Transversal) -16.04 -45.08 -46.83 -57.87 -56.63 1.8 ABM SNR (dB) 33.26 28.67 35.06 29.33 33.17 30.40 33.16 25.38 31.76 30.56 35.04 31.58 35.34 30.79 T- Plot No. Rating T4 T3 T4 T3 T4 T4 T4 55/ 56 T3 57 T4 T4 T4 T4 T4 T4 F-TP22-03 (Rev.00) 32 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 VoWi-Fi Air Interface Investigation (Continued) Mode 802.11a Voice EVS-WB Codec: 5.9 kbit/s 802.11n HT20 Voice EVS-WB Codec: 5.9 kbit/s 802.11n HT40 Voice EVS-WB Codec: 5.9 kbit/s 802.11ac VHT20 Voice EVS-WB Codec: 5.9 kbit/s 802.11ac VHT40 Voice EVS-WB Codec: 5.9 kbit/s 802.11ac VHT80 Voice AMR-WB EVS-WB Codec: 5.9 kbit/ Ch. Freq. BW BW /Modulation Orientation BPSK z(Axial) 6 Mbps y(Transversal) CH.40 5200 20 QPSK 18 Mbps z(Axial) y(Transversal) 64QAM z(Axial) 54 Mbps y(Transversal) MCS 0 z(Axial) 6.5 Mbps y(Transversal) CH.40 5200 20 MCS 3 26 Mbps z(Axial) y(Transversal) MCS 7 z(Axial) 65 Mbps y(Transversal) MCS 0 z(Axial) 13.5 Mbps y(Transversal) CH.38 5190 40 MCS 3 54 Mbps z(Axial) y(Transversal) MCS 7 z(Axial) 135 Mbps y(Transversal) MCS 0 z(Axial) 6.5 Mbps y(Transversal) CH.40 5200 20 MCS 4 39 Mbps z(Axial) y(Transversal) MCS 8 z(Axial) 78 Mbps y(Transversal) MCS 0 z(Axial) 13.5 Mbps y(Transversal) CH.38 5190 40 MCS 4 81 Mbps z(Axial) y(Transversal) MCS 9 z(Axial) 180 Mbps y(Transversal) MCS 0 29.3 Mbps CH.42 5210 80 MCS 4 175.5 Mbps z(Axial) y(Transversal) z(Axial) y(Transversal) MCS 9 z(Axial) 390 Mbps y(Transversal) ABM1 dB(A/m) -8.13 -21.43 -8.78 -17.66 -8.24 -18.84 -15.26 -22.46 -6.53 -21.28 -9.48 -17.41 -9.06 -21.87 -11.49 -21.67 -9.08 -20.75 -11.57 -22.78 -8.76 -17.77 -8.19 -22.50 -7.68 -18.63 -7.75 -19.59 -8.35 -23.01 -9.11 -18.44 -10.23 -21.63 -13.95 -22.12 ABM2 dB(A/m) -43.21 -49.89 -44.34 -51.21 -42.88 -49.44 -43.68 -51.02 -40.25 -48.15 -43.26 -49.65 -42.23 -49.13 -43.18 -52.98 -42.82 -52.07 -43.12 -51.91 -43.59 -49.22 -44.49 -53.37 -44.26 -50.54 -44.31 -50.49 -43.47 -52.94 -40.70 -49.12 -40.23 -51.81 -43.93 -52.62 Ambient Freq. Noise Response dB(A/m) (dB) -53.94 1.98 -48.18 -53.94 1.74 -48.18 -53.94 1.81 -48.18 -56.26 1.79 -55.77 -56.26 1.98 -55.77 -56.26 1.91 -55.77 -56.26 2.00 -55.77 -56.26 2.00 -55.77 -56.26 1.99 -55.77 -56.26 1.98 -55.77 -56.26 1.86 -55.77 -56.26 1.71 -55.77 -56.26 1.93 -55.77 -56.26 1.69 -55.77 -56.26 1.81 -55.77 -56.26 1.91 -55.77 -56.26 2.00 -55.77 -56.26 2.00 -55.77 ABM SNR (dB) 35.08 28.45 35.57 33.55 34.64 30.60 28.43 28.56 33.72 26.88 33.78 32.24 33.17 27.26 31.69 31.31 33.75 31.33 31.55 29.13 34.83 31.45 36.30 30.88 36.58 31.91 36.56 30.90 35.11 29.93 31.59 30.68 30.00 30.18 29.99 30.50 T- Plot Rating No. T4 T3 T4 T4 T4 T4 T3 T3 T3 58/ 59 T3 60 T4 T4 T4 T3 T4 T4 T4 T4 T4 T3 T4 T4 T4 T4 T4 T4 T4 T4 T4 T3 T4 T4 T3 T4 T3 T4 F-TP22-03 (Rev.00) 33 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Mode Ch. BW Freq. BW /Mode Orientation ABM1 ABM2 Ambient Freq. Noise Response dB(A/m) dB(A/m) dB(A/m) (dB) 802.11n HT20 Voice EVS -WB Codec: 5.9 kbit/s CH.56 5280 20 MCS 3 13.5 Mbps z(Axial) y(Transversal) -8.93 -15.48 -41.82 -44.71 -56.26 -55.77 1.68 802.11n HT20 Voice EVS -WB Codec: 5.9 kbit/s CH.120 5600 20 MCS 3 13.5 Mbps z(Axial) y(Transversal) -8.08 -19.00 -41.69 -48.02 -56.26 -55.77 1.77 802.11n HT20 Voice EVS -WB Codec: 5.9 kbit/s CH.157 5785 20 MCS 3 13.5 Mbps z(Axial) y(Transversal) -9.08 -18.18 -41.45 -45.45 -56.26 -55.77 2.00 802.11n HT20 Voice EVS -WB Codec: 5.9 kbit/s CH.36 5180 20 MCS 3 13.5 Mbps z(Axial) y(Transversal) -7.77 -19.78 -42.04 -47.52 -56.26 -55.77 1.74 802.11n HT20 Voice EVS -WB Codec: 5.9 kbit/s CH.48 5240 20 MCS 3 13.5 Mbps z(Axial) y(Transversal) -9.96 -21.36 -41.78 -50.59 -56.26 -55.77 1.89 ABM SNR (dB) 32.89 29.23 33.61 29.02 32.37 27.27 34.27 27.74 31.82 29.23 T- Plot Rating No. T4 61/ 62 T3 63 T4 64/ 65 T3 66 T4 67/ 68 T3 69 T4 70/ 71 T3 72 T4 73/ 74 T3 75 F-TP22-03 (Rev.00) 34 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 12.6 OTT Codec Investigation The DUT's nested OTT application supports range of codec bit rate 6 64 kbit/s, thus an investigation between the various codec configurations (6/64 as Low/High bit rates) and specific parameters are documented (ABM1, ABM2, S+N/N, frequency response) to determine the worst-case bit rates for each service type. The table below compares the varying codec configurations. Codec Investigation Codec State codec bit rate (kbit/s) 6 40 75 Orientation Band/ BandWidth/ Channel ABM1 (dB/m) -4.11 -5.87 -3.17 ABM2 (dBA/m) S+N/N (dB) Freq.Resposne (dB) ABM1 (dB/m) ABM2 (dBA/m) 36.33 32.22 2 -20.54 -51.62 38.98 33.12 2 -20.23 -52.15 -37.48 34.31 2 -20.72 -52.25 z (Axial) y(Transversal) GSM 850 EDGE 2 slots CH.190 836.6 S+N/N (dB) 31.08 31.92 31.53 ABM1 (dB/m) -7.86 -7.58 -5.03 ABM2 (dBA/m) S+N/N (dB) Freq.Resposne (dB) ABM1 (dB/m) ABM2 (dBA/m) -53.11 45.24 2.00 -13.77 -49.67 -52.25 44.67 2.00 -13.50 -50.39 -50.70 45.66 2.00 -11.86 -48.08 z (Axial) y(Transversal) WCDMA Band V HSUPA subtest 1 CH.4183 836.6 S+N/N (dB) 35.90 36.89 36.22 ABM1 (dB/m) -6.46 -4.00 -6.06 ABM2 (dBA/m) S+N/N (dB) -44.12 37.66 -34.96 30.96 -43.33 37.27 z (Axial) LTE Band 26 Freq.Resposne (dB) ABM1 (dB/m) 2.00 -17.67 2.00 -17.31 2.00 -17.33 15 16QAM RB 1/0 CH.26865 831.5 ABM2 (dBA/m) -45.33 -47.09 -45.23 y(Transversal) S+N/N (dB) 27.66 29.78 27.91 F-TP22-03 (Rev.00) 35 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Codec State ABM1 (dB/m) ABM2 (dBA/m) S+N/N (dB) Freq.Resposne (dB) ABM1 (dB/m) ABM2 (dBA/m) S+N/N (dB) ABM1 (dB/m) ABM2 (dBA/m) S+N/N (dB) Freq.Resposne (dB) ABM1 (dB/m) ABM2 (dBA/m) S+N/N (dB) ABM1 (dB/m) ABM2 (dBA/m) S+N/N (dB) Freq.Resposne (dB) ABM1 (dB/m) ABM2 (dBA/m) S+N/N (dB) ABM1 (dB/m) ABM2 (dBA/m) S+N/N (dB) Freq.Resposne (dB) ABM1 (dB/m) ABM2 (dBA/m) S+N/N (dB) Codec Investigation codec bit rate (kbit/s) 6 40 75 Orientation Band/ BandWidth/ Channel -4.64 -4.26 -4.48 -3.99 34.31 -38.76 34.51 -36.79 32.30 z (Axial) LTE Band 41 2.00 2.00 2.00 5 QPSK RB 1/12 -15.68 -21.90 -11.83 CH.41093 2640.3 -45.48 -51.45 -9.03 y(Transversal) 29.79 29.54 29.09 -2.48 5.54 3.72 -29.86 27.39 -24.56 30.10 -23.1 26.82 z (Axial) CDMA 1.62 1.06 1.45 1xEvDO Rev.A -4.85 -4.04 -4.36 CH. 670 822.75 -28.55 -27.14 -28.34 y(Transversal) 23.70 23.10 23.99 -11.96 -3.51 -3.58 -38.33 26.37 -38.48 34.96 -41.14 37.56 z (Axial) 802.11b CH.1 2.00 2.00 2.00 2412 -13.43 -16.76 -13.23 1Mbps -45.14 -47.96 -46.57 y(Transversal) 31.71 31.20 33.34 -3.68 -3.99 -3.83 -45.32 41.64 -45.30 41.30 -45.73 41.89 z (Axial) 802.11n HT20 2.00 2.00 2.00 CH.40 5200 -9.48 -13.46 -13.31 MCS 3 -50.02 -50.57 -51.12 y(Transversal) 40.53 37.11 37.81 F-TP22-03 (Rev.00) 36 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 12.7 OTT Air Interface Investigation Mode Ch. Freq. BW BW/ RB Mode Config. Orientation ABM1 dB(A/m) ABM2 dB(A/m) Ambient Noise dB(A/m) Freq. Response (dB) ABM SNR (dB) T-Rating Plot No. GSM850 EDGE 2 slots Duo Codec: 6 kbit/s CH.190 836.6 z(Axial) -4.11 -36.33 -57.85 2 32.22 T4 76/ 77 y(Transversal) -20.54 -51.62 -56.72 31.08 T4 78 GSM1900 EDGE 2 slots Duo Codec: 6 kbit/s CH.661 1880 z(Axial) -3.33 -35.41 -57.85 2 32.07 T4 79/ 80 y(Transversal) -16.5 -47.78 -56.72 31.29 T4 81 WCDMA Band II HSUPA subtest1 Duo Codec: 6 kbit/s CH.9400 1800 z(Axial) -1.23 -50.41 -57.85 2.0 49.19 T4 82/ 83 y(Transversal) -10.48 -51.42 -56.72 40.94 T4 84 WCDMA Band IV HSUPA subtest1 Duo Codec: 6 kbit/s CH.1412 1732.4 z(Axial) -1.15 -50.37 -57.85 2.0 49.22 T4 85/ 86 y(Transversal) -10.23 -51.08 -56.72 40.85 T4 87 WCDMA Band V HSUPA subtest1 Duo Codec: 6 kbit/s CH.4183 836.6 z(Axial) -7.86 -53.11 -57.85 2.0 45.24 T4 88/ 89 y(Transversal) -13.77 -49.67 -56.72 35.90 T4 90 LTE Band 26 Google Duo Codec: 6 kbit/s CH.26865 831.5 15 16QAM 1/0 z(Axial) -6.46 -44.12 -57.94 y(Transversal) -17.67 -45.33 -56.97 2.0 37.66 T4 27.66 T3 91/ 92 93 LTE Band 7 Google Duo Codec: 6 kbit/s CH.21100 2535 15 16QAM 1/0 z(Axial) -1.43 -48.68 -57.94 y(Transversal) -10.31 -48.59 -56.97 2.0 47.24 T4 38.28 T4 94/ 95 96 LTE Band 25 Google Duo Codec: 6 kbit/s CH.26365 1882.5 15 16QAM 1/0 z(Axial) -1.46 -47.43 -57.94 y(Transversal) -10.42 -49.72 -56.97 2.0 45.97 T4 39.30 T4 97/ 98 99 LTE Band 66 Google Duo Codec: 6 kbit/s CH.132322 15 1745 16QAM 1/0 z(Axial) -1.51 -42.34 -57.94 y(Transversal) -13.64 -48.23 -56.97 2.0 40.83 T4 100/ 101 34.59 T4 102 LTE Band 71 Google Duo Codec: 6 kbit/s CH.133297 15 680.5 16QAM 1/0 z(Axial) -1.19 -36.48 -57.94 y(Transversal) -15.15 -48.26 -56.97 2.0 35.29 T4 103/ 104 33.11 T4 105 LTE Band 12 Google Duo Codec: 6 kbit/s CH.23095 707.5 5 16QAM 1/0 z(Axial) -1.09 -35.91 -57.94 y(Transversal) -14.38 -47.14 -56.97 2.0 34.82 T4 106/ 107 32.76 T4 108 LTE Band 13 Google Duo Codec: 6 kbit/s CH.23230 782 5 16QAM 1/0 z(Axial) -1.24 -42.36 -57.94 y(Transversal) -14.52 -48.37 -56.97 2.0 41.12 T4 109/ 110 33.86 T4 111 LTE Band 14 Google Duo Codec: 6 kbit/s CH.23330 793 5 16QAM 1/0 z(Axial) -1.15 -43.74 -57.94 y(Transversal) -13.37 -46.77 -56.97 2.0 42.59 T4 112/ 113 33.40 T4 114 LTE Band 30 Google Duo Codec: 6 kbit/s CH.27710 2310 5 16QAM 1/0 z(Axial) y(Transversal) -1.06 -9.80 -46.23 -57.94 -46.13 -56.97 2.0 45.17 T4 115/ 116 36.33 T4 117 F-TP22-03 (Rev.00) 37 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Mode: Ch./ Freq. BW/ Data Rate BW/ RB Modulation Config. Orientation ABM1 dB(A/m) ABM2 dB(A/m) Ambient Noise dB(A/m) Freq. Respons e (dB) ABM SNR(dB) TRating Plot No. LTE Band 41 Google Duo Codec: 75 kbit/s CH.41093 2640.3 5 QPSK 1/12 z(Axial) -4.48 -36.79 -57.94 y(Transversal) -21.46 -50.55 -56.97 2.0 32.30 T4 118/ 119 29.09 T3 120 LTE Band 38 Google Duo Codec: 75 kbit/s CH.38000 2595 5 QPSK 1/12 z(Axial) -0.98 -40.83 -57.94 y(Transversal) -14.13 -47.53 -56.97 2.0 39.85 T4 121/ 122 33.40 T4 123 LTE Band 40 Google Duo Codec: 75 kbit/s CH.38775 2312.5 5 QPSK 1/12 z(Axial) 1.09 -41.38 -57.94 y(Transversal) -15.04 -50.85 -56.97 2.0 42.47 T4 124/ 125 35.81 T4 126 LTE Band 40 Goo gle Duo Codec: 7 5 kbit/s CH.39225 2357.5 5 QPSK 1/12 z(Axial) 0.58 -42.20 -57.94 y(Transversal) -11.55 -47.46 -56.97 2.0 42.77 T4 127/ 128 35.91 T4 129 Wi-Fi 2.4 802.11b Google Duo Codec: 6 kbit/s CH.1 2412 20 1Mbps z(Axial) -11.96 -38.33 -57.87 2.0 26.37 T3 130/ 131 y(Transversal) -13.43 -45.14 -56.63 31.71 T4 132 U-NII 5.2 802.11n HT20 Google Duo Codec: 40 kbit/s CH.40 5200 20 MCS3 z(Axial) -3.99 -45.30 -57.87 2.0 41.30 T4 133/ 134 y(Transversal) -13.46 -50.57 -56.63 37.11 T4 135 U-NII 5.3 802.11n HT20 Google Duo Codec: 40 kbit/s CH.56 5280 20 MCS3 z(Axial) -1.40 -44.52 -57.87 2.0 43.12 T4 136/ 137 y(Transversal) -9.40 -48.20 -56.63 38.80 T4 138 U-NII 5.6 802.11n HT20 Google Duo Codec: 40 kbit/s CH.120 5600 20 MCS3 z(Axial) -0.51 -44.50 -57.87 2.0 43.98 T4 139/ 140 y(Transversal) -13.06 -51.28 -56.63 38.22 T4 141 U-NII 5.8 802.11n HT20 Google Duo Codec: 40 kbit/s CH.157 5785 20 MCS3 z(Axial) -1.45 -45.91 -57.87 2.0 44.46 T4 142/ 143 y(Transversal) -12.80 -50.43 -56.63 37.63 T4 144 1x EVDO BC0 Rev.A Google Duo Codec: 40 kbit/s CH.384 836.52 z(Axial) 5.75 -20.11 -47.47 1.54 25.86 T3 145/ 146 y(Transversal) -4.61 -28.25 -47.47 23.64 T3 147 1xEVDO BC1 Rev.A Google Duo Codec: 40 kbit/s CH.600 1880 z(Axial) 3.92 -27.71 -47.47 1.39 31.63 T4 148/ 149 y(Transversal) -4.47 -27.56 -47.47 23.09 T3 150 1x EVDO BC10 Rev.A Google Duo Codec: 40 kbit/s CH.670 822.75 z(Axial) 5.54 -24.56 -47.47 1.06 30.10 T4 151/ 152 y(Transversal) -4.04 -27.14 -47.47 23.10 T3 153 1x EVDO BC1 Rev.A Google Duo Codec: 40 kbit/s CH.25 1851.25 z(Axial) 5.91 -28.09 -47.47 1.44 34.00 T4 154/ 155 y(Transversal) -4.87 -28.90 -47.47 24.03 T3 156 1x EVDO BC1 Rev.A Google Duo Codec: 40 kbit/s CH.1175 1908.75 z(Axial) 4.22 -29.96 -47.47 1.38 34.18 T4 157/ 158 y(Transversal) -5.12 -28.42 -47.47 23.30 T3 159 F-TP22-03 (Rev.00) 38 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 12.8 CDMA Air Interface Investigation CDMA/EVDO BC0 , PCS CDMA/EVDO, CDMA/EVDO BC10 Mode Ch. Freq. Orientation CDMA BC0 S068 RC1 Voice Coder Speech Codec: EVRC-B CH.384 836.52 z(Axial) y(Transversal) CDMA BC1 S068 RC1 Voice Coder Speech Codec: EVRC-B CH.600 1880 z(Axial) y(Transversal) ABM1 dB (A/m) 1.93 -5.5 4.17 -7.54 ABM2 dB (A/m) -22.38 -29.49 -29.46 -33.03 Ambient Noise dB(A/m) -47.47 Freq. Response (dB) ABMSNR (dB) TRating Plot No. 1.23 24.31 T3 160/ 161 -47.47 23.99 T3 162 -47.47 1.64 33.63 T4 163/ 164 -47.47 25.49 T3 165 CH.560 z(Axial) 3.77 -20.30 -47.47 1.55 24.07 T3 166/ 167 820 y(Transversal) -7.41 -31.05 -47.47 23.64 T3 168 CDMA BC10 S068 RC1 CH.450 z(Axial) 3.82 -20.98 -47.47 1.61 24.80 T3 169/ 170 Voice Coder Speech 817.25 Codec: EVRC-B y(Transversal) -7.74 -31.81 -47.47 24.07 T3 171 CH.670 z(Axial) 4.09 -19.22 -47.47 1.71 23.31 T3 172/ 173 822.75 y(Transversal) -5.19 -28.29 -47.47 23.11 T3 174 CDMA BC10 S068 RC3 CH.670 z(Axial) 3.76 -32.66 -47.47 1.61 36.42 T4 Voice Coder Speech 822.75 Codec: EVRC-B y(Transversal) -4.18 -32.87 -47.47 28.69 T3 CDMA BC10 S068 RC4 CH.670 z(Axial) 5.05 -32.02 -47.47 1.61 37.07 T4 Voice Coder Speech 822.75 Codec: EVRC-B y(Transversal) -3.66 -32.06 -47.47 28.41 T3 F-TP22-03 (Rev.00) 39 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 12.9 Radio Configuration for OTT VoIP (NR) An investigation was performed to determine the waveform, modulation, and RB configuration to be used for testing. Due to equipment limitations, the worst-case ABM1 from OTT VoIP was used with the ABM2 measured for each NR radio configuration. DFT-s-OFDM BPSK, 1RB, 99%RB offset was determined to be the worst- case configuration for the handset and will be used for full testing.Frequency Response measurements were not possible due to equipment limitations NR OTT VoIP SNNR by Radio Configuration (CP-OFDM) Mode: Ch./ Freq. BW BW/ RB Mode Config. Orientation ABM1 ABM2 dB(A/m) dB(A/m) Ambient Noise dB(A/m) Freq. ABM Response SNR (dB) (dB) TRating Plot No. n66 CP-OFDM CH.349000 1745 20 QPSK 1/1 z(Axial) -4.48 -49.84 y(Transversal) -21.46 -55.07 -55.62 -55.88 45.36 T4 33.61 T4 n66 CP-OFDM CH.349000 1745 20 QPSK 1/53 z(Axial) -4.48 -54.35 y(Transversal) -21.46 -55.05 -55.62 -55.88 49.87 T4 33.59 T4 n66 CP-OFDM CH.349000 1745 20 QPSK 1/104 z(Axial) y(Transversal) -4.48 -55.27 -21.46 -55.99 -55.62 -55.88 50.79 T4 34.53 T4 n66 CP-OFDM CH.349000 1745 20 QPSK 53/0 z(Axial) -4.48 -53.59 y(Transversal) -21.46 -55.02 -55.62 -55.88 49.11 T4 33.56 T4 n66 CP-OFDM CH.349000 1745 20 QPSK 53/26 z(Axial) y(Transversal) -4.48 -54.09 -21.46 -54.98 -55.62 -55.88 49.61 T4 33.52 T4 n66 CP-OFDM CH.349000 1745 20 QPSK 53/53 z(Axial) y(Transversal) -4.48 -55.05 -21.46 -55.09 -55.62 -55.88 50.57 T4 33.63 T4 n66 CP-OFDM CH.349000 1745 20 QPSK 106/0 z(Axial) y(Transversal) -4.48 -54.11 -21.46 -55.18 -55.62 -55.88 49.63 T4 33.72 T4 n66 CP-OFDM CH.349000 1745 20 16QAM 1/1 z(Axial) -4.48 -48.14 -55.62 y(Transversal) -21.46 -54.88 -55.88 43.66 T4 33.42 T4 n66 CP-OFDM CH.349000 1745 20 16QAM 1/53 z(Axial) -4.48 -54.98 y(Transversal) -21.46 -55.36 -55.62 -55.88 50.50 T4 33.90 T4 n66 CP-OFDM CH.349000 1745 20 16QAM 1/104 z(Axial) y(Transversal) -4.48 -48.73 -21.46 -55.08 -55.62 -55.88 44.25 T4 33.62 T4 n66 CP-OFDM CH.349000 1745 20 16QAM 53/0 z(Axial) -4.48 -54.78 y(Transversal) -21.46 -55.03 -55.62 -55.88 50.30 T4 33.57 T4 n66 CP-OFDM CH.349000 1745 20 16QAM 53/26 z(Axial) y(Transversal) -4.48 -54.85 -21.46 -54.97 -55.62 -55.88 50.37 T4 33.51 T4 n66 CP-OFDM CH.349000 1745 20 16QAM 53/53 z(Axial) y(Transversal) -4.48 -53.85 -21.46 -55.21 -55.62 -55.88 49.37 T4 33.75 T4 n66 CP-OFDM CH.349000 1745 20 16QAM 106/0 z(Axial) y(Transversal) -4.48 -54.40 -21.46 -54.93 -55.62 -55.88 49.92 T4 33.47 T4 F-TP22-03 (Rev.00) 40 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 n66 CP-OFDM n66 CP-OFDM n66 CP-OFDM n66 CP-OFDM n66 CP-OFDM n66 CP-OFDM n66 CP-OFDM n66 CP-OFDM n66 CP-OFDM n66 CP-OFDM n66 CP-OFDM n66 CP-OFDM n66 CP-OFDM n66 CP-OFDM CH.349000 1745 20 64QAM 1/1 z(Axial) -4.48 -48.61 -55.62 y(Transversal) -21.46 -54.92 -55.88 CH.349000 1745 20 64QAM 1/53 z(Axial) -4.48 -49.35 y(Transversal) -21.46 -55.21 -55.62 -55.88 CH.349000 1745 20 64QAM 1/104 z(Axial) y(Transversal) -4.48 -49.05 -21.46 -54.90 -55.62 -55.88 CH.349000 1745 20 64QAM 53/0 z(Axial) -4.48 -50.02 y(Transversal) -21.46 -55.12 -55.62 -55.88 CH.349000 1745 20 64QAM 53/26 z(Axial) y(Transversal) -4.48 -50.13 -21.46 -55.28 -55.62 -55.88 CH.349000 1745 20 64QAM 53/53 z(Axial) y(Transversal) -4.48 -53.78 -21.46 -55.45 -55.62 -55.88 CH.349000 1745 20 64QAM 106/0 z(Axial) y(Transversal) -4.48 -53.66 -21.46 -55.10 -55.62 -55.88 CH.349000 1745 20 256QAM 1/1 z(Axial) -4.48 -51.75 -55.62 y(Transversal) -21.46 -54.97 -55.88 CH.349000 1745 20 256QAM 1/53 z(Axial) -4.48 -53.65 y(Transversal) -21.46 -55.05 -55.62 -55.88 CH.349000 1745 20 256QAM 1/104 z(Axial) y(Transversal) -4.48 -55.51 -21.46 -55.91 -55.62 -55.88 CH.349000 1745 20 256QAM 53/0 z(Axial) -4.48 -54.88 y(Transversal) -21.46 -54.09 -55.62 -55.88 CH.349000 1745 20 256QAM 53/26 z(Axial) y(Transversal) -4.48 -54.05 -21.46 -55.11 -55.62 -55.88 CH.349000 1745 20 256QAM 53/53 z(Axial) y(Transversal) -4.48 -54.10 -21.46 -54.98 -55.62 -55.88 CH.349000 1745 20 256QAM 106/0 z(Axial) y(Transversal) -4.48 -53.47 -21.46 -55.18 -55.62 -55.88 44.13 T4 33.46 T4 44.87 T4 33.75 T4 44.57 T4 33.44 T4 45.54 T4 33.66 T4 45.65 T4 33.82 T4 49.30 T4 33.99 T4 49.18 T4 33.64 T4 47.27 T4 33.51 T4 49.17 T4 33.59 T4 51.03 T4 34.45 T4 50.40 T4 32.63 T4 49.57 T4 33.65 T4 49.62 T4 33.52 T4 48.99 T4 33.72 T4 F-TP22-03 (Rev.00) 41 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 NR OTT VoIP SNNR by Radio Configuration (DFT-s-OFDM) Mode: Ch./ Freq. BW BW/ RB Mode Config. Orientation ABM1 ABM2 dB(A/m) dB(A/m) Ambient Noise dB(A/m) Freq. Response (dB) ABM SNR (dB) TRating Plot No. n66 DFTs-OFDM CH.349000 1745 20 BPSK 1/1 z(Axial) -4.48 -46.60 y(Transversal) -21.46 -46.79 -47.09 -46.79 42.12 T4 25.33 T3 n66 DFTs-OFDM CH.349000 1745 20 BPSK 1/53 z(Axial) -4.48 -42.52 y(Transversal) -21.46 -46.85 -47.09 -46.79 38.04 T4 25.39 T3 n66 DFTs-OFDM CH.349000 1745 20 BPSK 1/104 z(Axial) y(Transversal) -4.48 -21.46 -34.42 -46.19 -47.09 -46.79 29.94 T3 24.73 T3 n66 DFTs-OFDM CH.349000 1745 20 BPSK 50/0 z(Axial) -4.48 -46.48 y(Transversal) -21.46 -46.85 -47.09 -46.79 42.00 T4 25.39 T3 n66 DFTs-OFDM CH.349000 1745 20 BPSK 50/28 z(Axial) y(Transversal) -4.48 -21.46 -47.02 -46.73 -47.09 -46.79 42.54 T4 25.27 T3 n66 DFTs-OFDM CH.349000 1745 20 BPSK 50/56 z(Axial) y(Transversal) -4.48 -21.46 -46.85 -46.95 -47.09 -46.79 42.37 T4 25.49 T3 n66 DFTs-OFDM CH.349000 1745 20 BPSK 100/0 z(Axial) y(Transversal) -4.48 -21.46 -46.37 -46.55 -47.09 -46.79 41.89 T4 25.09 T3 n66 DFTs-OFDM CH.349000 1745 20 QPSK 1/1 z(Axial) -4.48 -43.36 y(Transversal) -21.46 -46.62 -47.09 -46.79 38.88 T4 25.16 T3 n66 DFTs-OFDM CH.349000 1745 20 QPSK 1/53 z(Axial) -4.48 -47.05 y(Transversal) -21.46 -46.85 -47.09 -46.79 42.57 T4 25.39 T3 n66 DFTs-OFDM CH.349000 1745 20 QPSK 1/104 z(Axial) y(Transversal) -4.48 -21.46 -43.46 -46.63 -47.09 -46.79 38.98 T4 25.17 T3 n66 DFTs-OFDM CH.349000 1745 20 QPSK 50/0 z(Axial) -4.48 -46.72 y(Transversal) -21.46 -46.88 -47.09 -46.79 42.24 T4 25.42 T3 n66 DFTs-OFDM CH.349000 1745 20 QPSK 50/28 z(Axial) y(Transversal) -4.48 -21.46 -47.04 -46.59 -47.09 -46.79 42.56 T4 25.13 T3 n66 DFTs-OFDM CH.349000 1745 20 QPSK 50/56 z(Axial) y(Transversal) -4.48 -21.46 -47.11 -46.85 -47.09 -46.79 42.63 T4 25.39 T3 n66 DFTs-OFDM CH.349000 1745 20 QPSK 100/0 z(Axial) y(Transversal) -4.48 -21.46 -46.34 -46.63 -47.09 -46.79 41.86 T4 25.17 T3 n66 DFTs-OFDM CH.349000 1745 20 16QAM 1/1 z(Axial) -4.48 -40.23 y(Transversal) -21.46 -46.75 -47.09 -46.79 35.75 T4 25.29 T3 n66 DFTs-OFDM CH.349000 1745 20 16QAM 1/53 z(Axial) -4.48 -47.18 y(Transversal) -21.46 -47.05 -47.09 -46.79 42.70 T4 25.59 T3 n66 DFTs-OFDM CH.349000 1745 20 16QAM 1/104 z(Axial) y(Transversal) -4.48 -21.46 -40.96 -46.69 -47.09 -46.79 36.48 T4 25.23 T3 F-TP22-03 (Rev.00) 42 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 n66 DFTs-OFDM n66 DFTs-OFDM n66 DFTs-OFDM n66 DFTs-OFDM n66 DFTs-OFDM n66 DFTs-OFDM n66 DFTs-OFDM n66 DFTs-OFDM n66 DFTs-OFDM n66 DFTs-OFDM n66 DFTs-OFDM n66 DFTs-OFDM n66 DFTs-OFDM n66 DFTs-OFDM n66 DFTs-OFDM n66 DFTs-OFDM n66 DFTs-OFDM n66 DFTs-OFDM CH.349000 1745 20 16QAM 50/0 z(Axial) -4.48 -47.42 y(Transversal) -21.46 -47.35 CH.349000 1745 20 16QAM 50/28 z(Axial) y(Transversal) -4.48 -47.12 -21.46 -46.91 CH.349000 1745 20 16QAM 50/56 z(Axial) y(Transversal) -4.48 -47.21 -21.46 -46.77 CH.349000 1745 20 16QAM 100/0 z(Axial) y(Transversal) -4.48 -46.06 -21.46 -46.77 CH.349000 1745 20 64QAM 1/1 z(Axial) -4.48 -39.56 y(Transversal) -21.46 -46.60 CH.349000 1745 20 64QAM 1/53 z(Axial) -4.48 -45.38 y(Transversal) -21.46 -46.75 CH.349000 1745 20 64QAM 1/104 z(Axial) y(Transversal) -4.48 -40.28 -21.46 -46.90 CH.349000 1745 20 64QAM 50/0 z(Axial) -4.48 -43.20 y(Transversal) -21.46 -46.42 CH.349000 1745 20 64QAM 50/28 z(Axial) y(Transversal) -4.48 -47.52 -21.46 -46.40 CH.349000 1745 20 64QAM 50/56 z(Axial) y(Transversal) -4.48 -47.12 -21.46 -46.72 CH.349000 1745 20 64QAM 100/0 z(Axial) y(Transversal) -4.48 -45.78 -21.46 -46.89 CH.349000 1745 20 256QAM 1/1 z(Axial) -4.48 -47.11 y(Transversal) -21.46 -46.97 CH.349000 1745 20 256QAM 1/53 z(Axial) -4.48 -47.05 y(Transversal) -21.46 -47.75 CH.349000 1745 20 256QAM 1/104 z(Axial) y(Transversal) -4.48 -46.67 -21.46 -47.01 CH.349000 1745 20 256QAM 50/0 z(Axial) -4.48 -46.98 y(Transversal) -21.46 -46.82 CH.349000 1745 20 256QAM 50/28 z(Axial) y(Transversal) -4.48 -46.52 -21.46 -47.01 CH.349000 1745 20 256QAM 50/56 z(Axial) y(Transversal) -4.48 -44.58 -21.46 -46.48 CH.349000 1745 20 256QAM 100/0 z(Axial) y(Transversal) -4.48 -47.09 -21.46 -46.83 -47.09 -46.79 -47.09 -46.79 -47.09 -46.79 -47.09 -46.79 -47.09 -46.79 -47.09 -46.79 -47.09 -46.79 -47.09 -46.79 -47.09 -46.79 -47.09 -46.79 -47.09 -46.79 -47.09 -46.79 -47.09 -46.79 -47.09 -46.79 -47.09 -46.79 -47.09 -46.79 -47.09 -46.79 -47.09 -46.79 42.94 T4 25.89 T3 42.64 T4 25.45 T3 42.73 T4 25.31 T3 41.58 T4 25.31 T3 35.08 T4 25.14 T3 40.90 T4 25.29 T3 35.8 T4 25.44 T3 38.72 T4 24.96 T3 43.04 T4 24.94 T3 42.64 T4 25.26 T3 41.3 T4 25.43 T3 42.63 T4 25.51 T3 42.57 T4 26.29 T3 42.19 T4 25.55 T3 42.50 T4 26.29 T3 42.04 T4 25.55 T3 40.10 T4 25.02 T3 42.61 T4 25.37 T3 F-TP22-03 (Rev.00) 43 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 An investigation was performed to determine the worst-case NR band to be used for OTT VoIP testing. NR n2 was used for the testing as the worst-case configuration for the handset. See below table for SNNR comparison between different NR bands OTT VoIP (NR) SNNR by Band Mode: Ch./ Freq. BW BW/ RB Mode Config. Orientation ABM1 ABM2 dB(A/m) dB(A/m) Ambient Noise dB(A/m) Freq. ABM Response SNR (dB) (dB) TRating Plot No. n2 DFT-s-OFDM CH.376000 1880 20 BPSK 1/104 z(Axial) y(Transversal) -4.48 -42.02 -21.46 -46.65 -47.09 -46.79 37.54 T4 181 25.19 T3 182 n5 DFT-s-OFDM CH.167300 836.5 20 BPSK 1/104 z(Axial) y(Transversal) -4.48 -40.80 -21.46 -46.39 -47.09 -46.79 36.32 T4 179 24.93 T3 180 n71 DFT-s-OFDM CH.136100 680.5 20 BPSK 1/104 z(Axial) y(Transversal) -4.48 -47.05 -21.46 -46.79 -47.09 -46.79 42.57 T4 177 25.33 T3 178 Raw Data Results for NR n66 (OTT VoIP) Mode: Ch./ Freq. BW BW/ RB Mode Config. Orientation ABM1 ABM2 dB(A/m) dB(A/m) Ambient Noise dB(A/m) Freq. ABM Response SNR (dB) (dB) TRating Plot No. N66 DFT-s-OFDM CH.351160 1755.8 5 BPSK 1/104 z(Axial) y(Transversal) -4.48 -45.00 -21.46 -46.86 -47.09 -46.79 40.52 T4 183 25.40 T3 184 N66 DFT-s-OFDM CH.351000 1755 10 BPSK 1/104 z(Axial) y(Transversal) -4.48 -44.58 -21.46 -46.78 -47.09 -46.79 40.10 T4 185 25.32 T3 186 N66 DFT-s-OFDM CH.350820 1754.1 15 BPSK 1/104 z(Axial) y(Transversal) -4.48 -44.89 -21.46 -46.80 -47.09 -46.79 40.41 T4 187 25.34 T3 188 N66 DFT-s-OFDM CH.349000 1745 20 BPSK 1/104 z(Axial) y(Transversal) -4.48 -34.42 -21.46 -46.19 -47.09 -46.79 29.94 T3 175 24.73 T3 176 N66 DFT-s-OFDM CH.344000 1720 20 BPSK 1/104 z(Axial) y(Transversal) -4.48 -44.52 -21.46 -46.71 -47.09 -46.79 40.04 T4 189 25.25 T3 190 N66 DFT-s-OFDM CH.351500 1757.5 20 BPSK 1/104 z(Axial) y(Transversal) -4.48 -44.15 -21.46 -46.60 -47.09 -46.79 39.67 T4 191 25.14 T3 192 N66 DFT-s-OFDM CH.354000 1770 20 BPSK 1/104 z(Axial) y(Transversal) -4.48 -43.50 -21.46 -46.86 -47.09 -46.79 39.02 T4 193 25.40 T3 194 F-TP22-03 (Rev.00) 44 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Raw Data Results for NR n41 (OTT VoIP) Mode: Ch./ Freq. BW BW/ RB Mode Config. Orientation ABM1 ABM2 dB(A/m) dB(A/m) Ambient Noise dB(A/m) Freq. ABM Response SNR (dB) (dB) TRating Plot No. n41 CH.518598 DFT-s-OFDM 2592.99 20 BPSK 1/49 z(Axial) -4.48 -43.41 y(Transversal) -21.46 -54.29 -55.62 -55.88 38.93 T4 195 32.83 T4 196 n41 CH.518598 DFT-s-OFDM 2592.99 40 z(Axial) -4.48 -42.36 BPSK 1/104 y(Transversal) -21.46 -54.31 -55.62 -55.88 37.88 T4 197 32.85 T4 198 n41 CH.518598 DFT-s-OFDM 2592.99 50 z(Axial) -4.48 -42.04 BPSK 1/131 y(Transversal) -21.46 -54.43 -55.62 -55.88 37.56 T4 199 32.97 T4 200 n41 CH.518598 DFT-s-OFDM 2592.99 60 z(Axial) -4.48 -54.18 BPSK 1/160 y(Transversal) -21.46 -54.96 -55.62 -55.88 49.70 T4 201 33.50 T4 202 n41 CH.518598 DFT-s-OFDM 2592.99 80 z(Axial) -4.48 -53.89 BPSK 1/215 y(Transversal) -21.46 -54.94 -55.62 -55.88 49.41 T4 203 33.48 T4 204 n41 CH.518598 DFT-s-OFDM 2592.99 90 z(Axial) -4.48 -53.53 BPSK 1/243 y(Transversal) -21.46 -55.04 -55.62 -55.88 49.05 T4 205 33.58 T4 206 n41 CH.518598 DFT-s-OFDM 2592.99 100 BPSK 1/271 z(Axial) y(Transversal) -4.48 -54.24 -21.46 -55.04 -55.62 -55.88 49.76 T4 207 33.58 T4 208 n41 CH.501204 DFT-s-OFDM 2506.02 20 BPSK 1/49 z(Axial) -4.48 -42.13 y(Transversal) -21.46 -54.44 -55.62 -55.88 37.65 T4 209 32.98 T4 210 n41 CH.509898 DFT-s-OFDM 2549.49 20 BPSK 1/49 z(Axial) -4.48 -42.20 y(Transversal) -21.46 -54.33 -55.62 -55.88 37.72 T4 211 32.87 T4 212 n41 CH.527298 DFT-s-OFDM 2636.49 20 BPSK 1/49 z(Axial) -4.48 -42.24 y(Transversal) -21.46 -54.54 -55.62 -55.88 37.76 T4 213 33.08 T4 214 n41 CH.535998 DFT-s-OFDM 2679.99 20 BPSK 1/49 z(Axial) -4.48 -41.79 y(Transversal) -21.46 -54.27 -55.62 -55.88 37.31 T4 215 32.81 T4 216 F-TP22-03 (Rev.00) 45 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Attachment 1. HAC T-COIL Test Plots F-TP22-03 (Rev.00) 46 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.1 GSM850 AMR-NB FR V1 190ch z(axial) Communication System: UID 0, GSM 850 (0); Frequency: 836.6 MHz;Duty Cycle: 1:8.30042 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3049; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 26.3 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -3.11 dBA/m BWC Factor = 0.14 dB Location: 8.3, 4.2, 3.7 mm Cursor: ABM2 = -30.58 dBA/m Location: 8.3, 4.2, 3.7 mm Cursor: ABM1/ABM2 = 27.48 dB ABM1 comp = -3.11 dBA/m BWC Factor = 0.14 dB Location: 8.3, 4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 47 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No. 2 GSM850 AMR-NB FR V1 190ch Freq. Response Communication System: UID 0, GSM 850 (0); Frequency: 836.6 MHz;Duty Cycle: 1:8.30042 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 55.75 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.45 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.45 dB Location: 8.2, 4.7, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 48 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.3 GSM850 AMR-NB FR V1 190ch y(transversal) Communication System: UID 0, GSM 850 (0); Frequency: 836.6 MHz;Duty Cycle: 1:8.30042 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3049; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 26.3 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -14.44 dBA/m BWC Factor = 0.14 dB Location: -4.2, -4.2, 3.7 mm Cursor: ABM2 = -42.80 dBA/m Location: -4.2, -4.2, 3.7 mm Cursor: ABM1/ABM2 = 28.36 dB ABM1 comp = -14.44 dBA/m BWC Factor = 0.14 dB Location: -4.2, -4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 49 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.4 GSM1900 AMR-NB FR V1 661ch z(axial) Communication System: UID 0, GSM 1900 (0); Frequency: 1880 MHz;Duty Cycle: 1:8.30042 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3049; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 26.3 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.13 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = 1.53 dBA/m BWC Factor = 0.13 dB Location: 8.3, 4.2, 3.7 mm Cursor: ABM2 = -36.95 dBA/m Location: 8.3, 4.2, 3.7 mm Cursor: ABM1/ABM2 = 38.48 dB ABM1 comp = 1.53 dBA/m BWC Factor = 0.13 dB Location: 8.3, 4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 50 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.5 GSM1900 AMR-NB FR V1 661ch Freq. Response Communication System: UID 0, GSM 1900 (0); Frequency: 1880 MHz;Duty Cycle: 1:8.30042 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 55.75 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.45 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.45 dB Location: 8.2, 4.7, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 51 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.6 GSM1900 AMR-NB FR V1 661ch y(transversal) Communication System: UID 0, GSM 1900 (0); Frequency: 1880 MHz;Duty Cycle: 1:8.30042 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3049; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 26.3 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.13 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -10.54 dBA/m BWC Factor = 0.13 dB Location: -4.2, -4.2, 3.7 mm Cursor: ABM2 = -45.04 dBA/m Location: -4.2, -4.2, 3.7 mm Cursor: ABM1/ABM2 = 34.50 dB ABM1 comp = -10.54 dBA/m BWC Factor = 0.13 dB Location: -4.2, -4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 52 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.7 WCDMA Band 4 AMR WB 6_6 1412ch z(axial) Communication System: UID 0, WCDMA IV (0); Frequency: 1732.4 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3049; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 26.3 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.13 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -3.04 dBA/m BWC Factor = 0.13 dB Location: 8.3, 8.3, 3.7 mm Cursor: ABM2 = -45.98 dBA/m Location: 8.3, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 42.95 dB ABM1 comp = -3.04 dBA/m BWC Factor = 0.13 dB Location: 8.3, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 53 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.8 WCDMA Band 4 AMR WB 6_6 1412ch Freq. Response Communication System: UID 0, WCDMA IV (0); Frequency: 1732.4 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 55.75 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.44 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.44 dB Location: 7.6, 7.3, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 54 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.9 WCDMA Band 4 AMR WB 6_6 1412ch- y(transversal) Communication System: UID 0, WCDMA IV (0); Frequency: 1732.4 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3049; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 26.3 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.13 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -10.25 dBA/m BWC Factor = 0.13 dB Location: 4.2, 16.7, 3.7 mm Cursor: ABM2 = -45.94 dBA/m Location: 4.2, 16.7, 3.7 mm Cursor: ABM1/ABM2 = 35.69 dB ABM1 comp = -10.25 dBA/m BWC Factor = 0.13 dB Location: 4.2, 16.7, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 55 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.10 WCDMA Band 2 AMR WB 6_6 9400ch_z(axial) Communication System: UID 0, WCDMA1900 (0); Frequency: 1880 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3049; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 26.3 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.13 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -3.11 dBA/m BWC Factor = 0.13 dB Location: 8.3, 8.3, 3.7 mm Cursor: ABM2 = -46.16 dBA/m Location: 8.3, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 43.04 dB ABM1 comp = -3.11 dBA/m BWC Factor = 0.13 dB Location: 8.3, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 56 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.11 WCDMA Band 2 AMR WB 6_6 9400ch_Freq. Response Communication System: UID 0, WCDMA1900 (0); Frequency: 1880 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 55.75 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.44 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.44 dB Location: 7.5, 7.9, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 57 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.12 WCDMA Band 2 AMR WB 6_6 9400ch_y(transversal) Communication System: UID 0, WCDMA1900 (0); Frequency: 1880 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3049; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 26.3 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.13 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -10.40 dBA/m BWC Factor = 0.13 dB Location: 4.2, 16.7, 3.7 mm Cursor: ABM2 = -46.18 dBA/m Location: 4.2, 16.7, 3.7 mm Cursor: ABM1/ABM2 = 35.77 dB ABM1 comp = -10.40 dBA/m BWC Factor = 0.13 dB Location: 4.2, 16.7, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 58 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.13 WCDMA Band 5 AMR WB 6_6 4183ch_z(axial) Communication System: UID 0, WCDMA850 (0); Frequency: 836.6 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3049; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 26.3 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.13 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -3.11 dBA/m BWC Factor = 0.13 dB Location: 8.3, 8.3, 3.7 mm Cursor: ABM2 = -46.23 dBA/m Location: 8.3, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 43.12 dB ABM1 comp = -3.11 dBA/m BWC Factor = 0.13 dB Location: 8.3, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 59 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.14 WCDMA Band 5 AMR WB 6_6 4183ch Freq. Response Communication System: UID 0, WCDMA850 (0); Frequency: 836.6 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 55.75 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.44 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.44 dB Location: 7.9, 8, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 60 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.15 WCDMA Band 5 AMR WB 6_6 4183ch y(transversal) Communication System: UID 0, WCDMA850 (0); Frequency: 836.6 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3049; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 26.3 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.13 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -10.53 dBA/m BWC Factor = 0.13 dB Location: 4.2, 16.7, 3.7 mm Cursor: ABM2 = -45.90 dBA/m Location: 4.2, 16.7, 3.7 mm Cursor: ABM1/ABM2 = 35.37 dB ABM1 comp = -10.53 dBA/m BWC Factor = 0.13 dB Location: 4.2, 16.7, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 61 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.16 LTE Band 25 AMR WB 6_6 16QAM 20MHz 1RB 0offset 26365ch z(axial) Communication System: UID 0, LTE Band 25 (0); Frequency: 1882.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3049; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 26.3 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.13 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -2.70 dBA/m BWC Factor = 0.13 dB Location: 8.3, 8.3, 3.7 mm Cursor: ABM2 = -41.14 dBA/m Location: 8.3, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 38.44 dB ABM1 comp = -2.70 dBA/m BWC Factor = 0.13 dB Location: 8.3, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 62 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.17 LTE Band 25 AMR WB 6_6 16QAM 20MHz 1RB 0offset 26365ch Freq. Response Communication System: UID 0, LTE Band 25 (0); Frequency: 1882.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 55.75 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.44 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.44 dB Location: 8.5, 6.8, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 63 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.18 LTE Band 25 AMR WB 6_6 16QAM 20MHz 1RB 0offset 26365ch y(transversal) Communication System: UID 0, LTE Band 25 (0); Frequency: 1882.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3049; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 26.3 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.13 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -13.49 dBA/m BWC Factor = 0.13 dB Location: 0, -4.2, 3.7 mm Cursor: ABM2 = -45.04 dBA/m Location: 0, -4.2, 3.7 mm Cursor: ABM1/ABM2 = 31.54 dB ABM1 comp = -13.49 dBA/m BWC Factor = 0.13 dB Location: 0, -4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 64 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.19 LTE Band 7 AMR WB 6_6 16QAM 20MHz 1RB 0offset 21100ch z(axial) Communication System: UID 0, LTE Band 7 (0); Frequency: 2535 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3049; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 26.3 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.13 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -2.61 dBA/m BWC Factor = 0.13 dB Location: 8.3, 8.3, 3.7 mm Cursor: ABM2 = -43.34 dBA/m Location: 8.3, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 40.73 dB ABM1 comp = -2.61 dBA/m BWC Factor = 0.13 dB Location: 8.3, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 65 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.20 LTE Band 7 AMR WB 6_6 16QAM 20MHz 1RB 0offset 21100ch Freq. Response Communication System: UID 0, LTE Band 7 (0); Frequency: 2535 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 55.75 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.44 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.44 dB Location: 8.3, 7.5, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 66 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.21 LTE Band 7 AMR WB 6_6 16QAM 20MHz 1RB 0offset 21100ch y(transversal) Communication System: UID 0, LTE Band 7 (0); Frequency: 2535 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3049; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 26.3 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.13 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -12.42 dBA/m BWC Factor = 0.13 dB Location: 0, 0, 3.7 mm Cursor: ABM2 = -45.47 dBA/m Location: 0, 0, 3.7 mm Cursor: ABM1/ABM2 = 33.05 dB ABM1 comp = -12.42 dBA/m BWC Factor = 0.13 dB Location: 0, 0, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 67 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.22 LTE Band 12 AMR WB 6_6 16QAM 10MHz 1RB 0offset 21100ch z(axial) Communication System: UID 0, LTE 12 (0); Frequency: 707.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3049; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 26.3 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.13 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -2.81 dBA/m BWC Factor = 0.13 dB Location: 4.2, 8.3, 3.7 mm Cursor: ABM2 = -35.85 dBA/m Location: 4.2, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 33.04 dB ABM1 comp = -2.81 dBA/m BWC Factor = 0.13 dB Location: 4.2, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 68 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.23 LTE Band 12 AMR WB 6_6 16QAM 10MHz 1RB 0offset 21100ch Freq. Response Communication System: UID 0, LTE 12 (0); Frequency: 707.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 55.75 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.44 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.44 dB Location: 4.2, 8.4, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 69 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.24 LTE Band 12 AMR WB 6_6 16QAM 10MHz 1RB 0offset 21100ch y(transversal) Communication System: UID 0, LTE 12 (0); Frequency: 707.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3049; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 26.3 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.13 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -13.36 dBA/m BWC Factor = 0.13 dB Location: 0, -4.2, 3.7 mm Cursor: ABM2 = -43.76 dBA/m Location: 0, -4.2, 3.7 mm Cursor: ABM1/ABM2 = 30.40 dB ABM1 comp = -13.36 dBA/m BWC Factor = 0.13 dB Location: 0, -4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 70 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.25 LTE Band 13 AMR WB 6_6 16QAM 10MHz 1RB 0offset 23230ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 13 (0); Frequency: 782 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3049; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 26.3 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.13 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -2.71 dBA/m BWC Factor = 0.13 dB Location: 8.3, 8.3, 3.7 mm Cursor: ABM2 = -41.75 dBA/m Location: 8.3, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 39.04 dB ABM1 comp = -2.71 dBA/m BWC Factor = 0.13 dB Location: 8.3, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 71 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.26 LTE Band 13 AMR WB 6_6 16QAM 10MHz 1RB 0offset 23230ch Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 13 (0); Frequency: 782 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 55.75 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.44 dB Device Reference Point: 0, 0, -6.3 mm Category Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] Category T1 0 dB to 10 dB Category T2 10 dB to 20 dB Category T3 20 dB to 30 dB Category T4 > 30 dB Cursor: Diff = 2.00 dB BWC Factor = 9.44 dB Location: 8.1, 7.2, 3.7 mm F-TP22-03 (Rev.00) 72 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.27 LTE Band 13 AMR WB 6_6 16QAM 10MHz 1RB 0offset 23230ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 13 (0); Frequency: 782 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3049; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 26.3 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.13 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -10.12 dBA/m BWC Factor = 0.13 dB Location: 4.2, 0, 3.7 mm Cursor: ABM2 = -41.82 dBA/m Location: 4.2, 0, 3.7 mm Cursor: ABM1/ABM2 = 31.70 dB ABM1 comp = -10.12 dBA/m BWC Factor = 0.13 dB Location: 4.2, 0, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 73 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.28 LTE Band 14 AMR WB 6_6 16QAM 10MHz 1RB 0offset 23330ch z(axial) Communication System: UID 0, LTE 14 (0); Frequency: 793 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3049; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 26.3 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.13 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -4.58 dBA/m BWC Factor = 0.13 dB Location: 12.5, 8.3, 3.7 mm Cursor: ABM2 = -41.70 dBA/m Location: 12.5, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 37.12 dB ABM1 comp = -4.58 dBA/m BWC Factor = 0.13 dB Location: 12.5, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 74 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.29 LTE Band 14 AMR WB 6_6 16QAM 10MHz 1RB 0offset 23330ch Freq. Response Communication System: UID 0, LTE 14 (0); Frequency: 793 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 55.75 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.44 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.44 dB Location: 11.1, 8.5, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 75 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.30 LTE Band 14 AMR WB 6_6 16QAM 10MHz 1RB 0offset 23330ch y(transversal) Communication System: UID 0, LTE 14 (0); Frequency: 793 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3049; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 26.3 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.13 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -13.70 dBA/m BWC Factor = 0.13 dB Location: 0, -4.2, 3.7 mm Cursor: ABM2 = -45.20 dBA/m Location: 0, -4.2, 3.7 mm Cursor: ABM1/ABM2 = 31.50 dB ABM1 comp = -13.70 dBA/m BWC Factor = 0.13 dB Location: 0, -4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 76 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.31 LTE Band 26 AMR WB 6_6 16QAM 15MHz 1RB 0offset 26865ch z(axial) Communication System: UID 0, LTE Band 26 (0); Frequency: 831.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3049; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 26.3 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.13 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -3.51 dBA/m BWC Factor = 0.13 dB Location: 8.3, 8.3, 3.7 mm Cursor: ABM2 = -36.41 dBA/m Location: 8.3, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 32.90 dB ABM1 comp = -3.51 dBA/m BWC Factor = 0.13 dB Location: 8.3, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 77 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.32 LTE Band 26 AMR WB 6_6 16QAM 15MHz 1RB 0offset 26865ch Freq. Response Communication System: UID 0, LTE Band 26 (0); Frequency: 831.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 55.75 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.44 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.44 dB Location: 7.9, 8.2, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB Plot No.33 F-TP22-03 (Rev.00) 78 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 LTE Band 26 AMR WB 6_6 16QAM 15MHz 1RB 0offset 26865ch y(transversal) Communication System: UID 0, LTE Band 26 (0); Frequency: 831.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3049; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 26.3 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.13 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -13.32 dBA/m BWC Factor = 0.13 dB Location: 0, -4.2, 3.7 mm Cursor: ABM2 = -43.24 dBA/m Location: 0, -4.2, 3.7 mm Cursor: ABM1/ABM2 = 29.92 dB ABM1 comp = -13.32 dBA/m BWC Factor = 0.13 dB Location: 0, -4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 79 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.34 LTE Band 30 AMR WB 6_6 16QAM 10MHz 1RB 0offset 27710ch z(axial) Communication System: UID 0, LTE 30 (0); Frequency: 2310 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3049; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 26.3 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.13 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -3.90 dBA/m BWC Factor = 0.13 dB Location: 8.3, 8.3, 3.7 mm Cursor: ABM2 = -43.77 dBA/m Location: 8.3, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 39.87 dB ABM1 comp = -3.90 dBA/m BWC Factor = 0.13 dB Location: 8.3, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 80 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.35 LTE Band 30 AMR WB 6_6 16QAM 10MHz 1RB 0offset 27710ch Freq. Response Communication System: UID 0, LTE 30 (0); Frequency: 2310 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 55.75 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.44 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.44 dB Location: 8.1, 8, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 81 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.36 LTE Band 30 AMR WB 6_6 16QAM 10MHz 1RB 0offset 27710ch y(transversal) Communication System: UID 0, LTE 30 (0); Frequency: 2310 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3049; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 26.3 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.13 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -12.43 dBA/m BWC Factor = 0.13 dB Location: 0, 0, 3.7 mm Cursor: ABM2 = -44.60 dBA/m Location: 0, 0, 3.7 mm Cursor: ABM1/ABM2 = 32.17 dB ABM1 comp = -12.43 dBA/m BWC Factor = 0.13 dB Location: 0, 0, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 82 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.37 LTE Band 66 AMR WB 6_6 16QAM 20MHz 1RB 0offset 132322ch z(axial) Communication System: UID 0, LTE Band 66 (0); Frequency: 1745 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3049; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 26.3 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.13 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -3.46 dBA/m BWC Factor = 0.13 dB Location: 8.3, 8.3, 3.7 mm Cursor: ABM2 = -43.06 dBA/m Location: 8.3, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 39.60 dB ABM1 comp = -3.46 dBA/m BWC Factor = 0.13 dB Location: 8.3, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 83 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.38 LTE Band 66 AMR WB 6_6 16QAM 20MHz 1RB 0offset 132322ch Freq. Response Communication System: UID 0, LTE Band 66 (0); Frequency: 1745 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 55.75 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.44 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.44 dB Location: 8.1, 7.9, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 84 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.39 LTE Band 66 AMR WB 6_6 16QAM 20MHz 1RB 0offset 132322ch y(transversal) Communication System: UID 0, LTE Band 66 (0); Frequency: 1745 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3049; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 26.3 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.13 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -11.99 dBA/m BWC Factor = 0.13 dB Location: 0, 0, 3.7 mm Cursor: ABM2 = -44.01 dBA/m Location: 0, 0, 3.7 mm Cursor: ABM1/ABM2 = 32.02 dB ABM1 comp = -11.99 dBA/m BWC Factor = 0.13 dB Location: 0, 0, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 85 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.40 LTE Band 71 AMR WB 6_6 16QAM 20MHz 1RB 0offset 133322ch z(axial) Communication System: UID 0, LTE 71 (0); Frequency: 683 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3049; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 26.3 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.13 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -5.42 dBA/m BWC Factor = 0.13 dB Location: 8.3, 4.2, 3.7 mm Cursor: ABM2 = -43.08 dBA/m Location: 8.3, 4.2, 3.7 mm Cursor: ABM1/ABM2 = 37.67 dB ABM1 comp = -5.42 dBA/m BWC Factor = 0.13 dB Location: 8.3, 4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 86 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.41 LTE Band 71 AMR WB 6_6 16QAM 20MHz 1RB 0offset 133322ch Freq. Response Communication System: UID 0, LTE 71 (0); Frequency: 683 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 55.75 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.44 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.44 dB Location: 8.1, 4.5, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 87 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.42 LTE Band 71 AMR WB 6_6 16QAM 20MHz 1RB 0offset 133322ch y(transversal) Communication System: UID 0, LTE 71 (0); Frequency: 683 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3049; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 26.3 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.13 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -13.44 dBA/m BWC Factor = 0.13 dB Location: 0, -4.2, 3.7 mm Cursor: ABM2 = -43.63 dBA/m Location: 0, -4.2, 3.7 mm Cursor: ABM1/ABM2 = 30.19 dB ABM1 comp = -13.44 dBA/m BWC Factor = 0.13 dB Location: 0, -4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 88 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.43 LTE 38 EVS-WB 5_9 QPSK 5MHz 1RB 12offset 38000ch Configuration 0 6 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 41 (0); Frequency: 2593 MHz;Duty Cycle: 1:1.58016 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3050; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2020-02-26 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 24.92 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.16 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -6.67 dBA/m BWC Factor = 0.16 dB Location: 4.2, 8.3, 3.7 mm Cursor: ABM2 = -35.23 dBA/m Location: 4.2, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 28.56 dB ABM1 comp = -6.67 dBA/m BWC Factor = 0.16 dB Location: 4.2, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 89 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.44 LTE 38 EVS-WB 5_9 QPSK 5MHz 1RB 12offset 38000ch Configuration 0 6 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 41 (0); Frequency: 2593 MHz;Duty Cycle: 1:1.58016 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 53.55 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.45 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 1.69 dB BWC Factor = 9.45 dB Location: 4.1, 8.4, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 90 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.45 LTE 38 EVS-WB 5_9 QPSK 5MHz 1RB 12offset 38000ch Configuration 0 6 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 41 (0); Frequency: 2593 MHz;Duty Cycle: 1:1.58016 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3050; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2020-02-26 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 24.92 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.16 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -19.76 dBA/m BWC Factor = 0.16 dB Location: -4.2, 20.8, 3.7 mm Cursor: ABM2 = -46.79 dBA/m Location: -4.2, 20.8, 3.7 mm Cursor: ABM1/ABM2 = 27.03 dB ABM1 comp = -19.76 dBA/m BWC Factor = 0.16 dB Location: -4.2, 20.8, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 91 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.46 LTE 40 EVS-WB 5_9 QPSK 5MHz 1RB 12offset 38750ch Configuration 0 6 Low Side z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band40 (0); Frequency: 2310 MHz;Duty Cycle: 1:1.58016 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3050; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2020-02-26 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 24.92 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.16 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -9.44 dBA/m BWC Factor = 0.16 dB Location: 4.2, 12.5, 3.7 mm Cursor: ABM2 = -37.16 dBA/m Location: 4.2, 12.5, 3.7 mm Cursor: ABM1/ABM2 = 27.72 dB ABM1 comp = -9.44 dBA/m BWC Factor = 0.16 dB Location: 4.2, 12.5, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 92 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.47 LTE 40 EVS-WB 5_9 QPSK 5MHz 1RB 12offset 38750ch Configuration 0 6 Low Side Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band40 (0); Frequency: 2310 MHz;Duty Cycle: 1:1.58016 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 53.55 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.48 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 1.86 dB BWC Factor = 9.48 dB Location: 3.7, 13.3, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 93 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.48 LTE 40 EVS-WB 5_9 QPSK 5MHz 1RB 12offset 38750ch Configuration 0 6 Low Side- y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band40 (0); Frequency: 2310 MHz;Duty Cycle: 1:1.58016 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3050; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2020-02-26 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 24.92 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.16 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -15.88 dBA/m BWC Factor = 0.16 dB Location: 0, 16.7, 3.7 mm Cursor: ABM2 = -43.18 dBA/m Location: 0, 16.7, 3.7 mm Cursor: ABM1/ABM2 = 27.30 dB ABM1 comp = -15.88 dBA/m BWC Factor = 0.16 dB Location: 0, 16.7, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 94 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.49 LTE 40 EVS-WB 5_9 QPSK 5MHz 1RB 12offset 39200ch Configuration 0 6 Upper Side- z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band40 (0); Frequency: 2355 MHz;Duty Cycle: 1:1.58016 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3050; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2020-02-26 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 24.92 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.16 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -10.49 dBA/m BWC Factor = 0.16 dB Location: 0, 4.2, 3.7 mm Cursor: ABM2 = -39.15 dBA/m Location: 0, 4.2, 3.7 mm Cursor: ABM1/ABM2 = 28.67 dB ABM1 comp = -10.49 dBA/m BWC Factor = 0.16 dB Location: 0, 4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 95 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.50 LTE 40 EVS-WB 5_9 QPSK 5MHz 1RB 12offset 39200ch Configuration 0 6 Upper Side Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band40 (0); Frequency: 2355 MHz;Duty Cycle: 1:1.58016 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 53.55 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.48 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 1.62 dB BWC Factor = 9.48 dB Location: 0.3, 4.2, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 96 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.51 LTE 40 EVS-WB 5_9 QPSK 5MHz 1RB 12offset 39200ch Configuration 0 6 Upper Side y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band40 (0); Frequency: 2355 MHz;Duty Cycle: 1:1.58016 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3050; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2020-02-26 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 24.92 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.16 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -16.44 dBA/m BWC Factor = 0.16 dB Location: 0, -4.2, 3.7 mm Cursor: ABM2 = -43.76 dBA/m Location: 0, -4.2, 3.7 mm Cursor: ABM1/ABM2 = 27.32 dB ABM1 comp = -16.44 dBA/m BWC Factor = 0.16 dB Location: 0, -4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 97 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.52 LTE 41 EVS-WB 5_9 QPSK 5MHz 1RB 12offset 41093ch Configuration 0 6 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 41 (0); Frequency: 2640.3 MHz;Duty Cycle: 1:1.58016 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3050; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2020-02-26 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 24.92 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.16 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -8.43 dBA/m BWC Factor = 0.16 dB Location: 8.3, 4.2, 3.7 mm Cursor: ABM2 = -35.09 dBA/m Location: 8.3, 4.2, 3.7 mm Cursor: ABM1/ABM2 = 26.67 dB ABM1 comp = -8.43 dBA/m BWC Factor = 0.16 dB Location: 8.3, 4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 98 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.53 LTE 41 EVS-WB 5_9 QPSK 5MHz 1RB 12offset 41093ch Configuration 0 6 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 41 (0); Frequency: 2640.3 MHz;Duty Cycle: 1:1.58016 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 53.55 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.48 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.48 dB Location: 7.8, 4.6, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 99 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.54 LTE 41 EVS-WB 5_9 QPSK 5MHz 1RB 12offset 41093ch Configuration 0 6 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 41 (0); Frequency: 2640.3 MHz;Duty Cycle: 1:1.58016 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV3 - 3050; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2020-02-26 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 24.92 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.16 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -18.09 dBA/m BWC Factor = 0.16 dB Location: 0, -4.2, 3.7 mm Cursor: ABM2 = -42.78 dBA/m Location: 0, -4.2, 3.7 mm Cursor: ABM1/ABM2 = 24.69 dB ABM1 comp = -18.09 dBA/m BWC Factor = 0.16 dB Location: 0, -4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 100 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.55 802_11b 1Mbps EVS wb 5_9 1ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, 2450MHz FCC (0); Frequency: 2412 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 16.48 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -9.46 dBA/m BWC Factor = 0.14 dB Location: 4.2, 8.3, 3.7 mm Cursor: ABM2 = -42.62 dBA/m Location: 4.2, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 33.16 dB ABM1 comp = -9.46 dBA/m BWC Factor = 0.14 dB Location: 4.2, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 101 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.56 802_11b 1Mbps EVS wb 5_9 1ch Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, 2450MHz FCC (0); Frequency: 2412 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 50.05 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 1.93 dB BWC Factor = 9.46 dB Location: 4.3, 7.9, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 102 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.57 802_11b 1Mbps EVS wb 5_9 1ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, 2450MHz FCC (0); Frequency: 2412 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 16.48 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -19.20 dBA/m BWC Factor = 0.14 dB Location: 0, -4.2, 3.7 mm Cursor: ABM2 = -44.58 dBA/m Location: 0, -4.2, 3.7 mm Cursor: ABM1/ABM2 = 25.38 dB ABM1 comp = -19.20 dBA/m BWC Factor = 0.14 dB Location: 0, -4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 103 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.58 802_11n20 MCS3 EVS wb 5_9 40ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5200 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 16.48 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -6.53 dBA/m BWC Factor = 0.14 dB Location: 8.3, 4.2, 3.7 mm Cursor: ABM2 = -40.25 dBA/m Location: 8.3, 4.2, 3.7 mm Cursor: ABM1/ABM2 = 33.72 dB ABM1 comp = -6.53 dBA/m BWC Factor = 0.14 dB Location: 8.3, 4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 104 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.59 802_11n20 MCS3 EVS wb 5_9 40ch Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5200 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 50.05 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 1.98 dB BWC Factor = 9.46 dB Location: 8.4, 4.1, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 105 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.60 802_11n20 MCS3 EVS wb 5_9 40ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5200 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 16.48 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -21.28 dBA/m BWC Factor = 0.14 dB Location: 0, 12.5, 3.7 mm Cursor: ABM2 = -48.15 dBA/m Location: 0, 12.5, 3.7 mm Cursor: ABM1/ABM2 = 26.88 dB ABM1 comp = -21.28 dBA/m BWC Factor = 0.14 dB Location: 0, 12.5, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 106 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.61 802_11n20 MCS3 EVS wb 5_9 56ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5280 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 16.48 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -8.93 dBA/m BWC Factor = 0.14 dB Location: 4.2, 12.5, 3.7 mm Cursor: ABM2 = -41.82 dBA/m Location: 4.2, 12.5, 3.7 mm Cursor: ABM1/ABM2 = 32.89 dB ABM1 comp = -8.93 dBA/m BWC Factor = 0.14 dB Location: 4.2, 12.5, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 107 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.62 802_11n20 MCS3 EVS wb 5_9 56ch Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5280 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 50.05 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 1.68 dB BWC Factor = 9.46 dB Location: 4.1, 12, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 108 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.63 802_11n20 MCS3 EVS wb 5_9 56ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5280 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 16.48 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -15.48 dBA/m BWC Factor = 0.14 dB Location: 4.2, 16.7, 3.7 mm Cursor: ABM2 = -44.71 dBA/m Location: 4.2, 16.7, 3.7 mm Cursor: ABM1/ABM2 = 29.23 dB ABM1 comp = -15.48 dBA/m BWC Factor = 0.14 dB Location: 4.2, 16.7, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 109 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.64 802_11n20 MCS3 EVS wb 5_9 120ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5600 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 16.48 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -8.08 dBA/m BWC Factor = 0.14 dB Location: 4.2, 8.3, 3.7 mm Cursor: ABM2 = -41.69 dBA/m Location: 4.2, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 33.61 dB ABM1 comp = -8.08 dBA/m BWC Factor = 0.14 dB Location: 4.2, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 110 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.65 802_11n20 MCS3 EVS wb 5_9 120ch Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5600 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 50.05 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 1.77 dB BWC Factor = 9.46 dB Location: 4.3, 8.3, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 111 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.66 802_11n20 MCS3 EVS wb 5_9 120ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5600 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 16.48 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -19.00 dBA/m BWC Factor = 0.14 dB Location: 0, 20.8, 3.7 mm Cursor: ABM2 = -48.02 dBA/m Location: 0, 20.8, 3.7 mm Cursor: ABM1/ABM2 = 29.02 dB ABM1 comp = -19.00 dBA/m BWC Factor = 0.14 dB Location: 0, 20.8, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 112 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.67 802_11n20 MCS3 EVS wb 5_9 157ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5785 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 16.48 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -9.08 dBA/m BWC Factor = 0.14 dB Location: 8.3, 12.5, 3.7 mm Cursor: ABM2 = -41.45 dBA/m Location: 8.3, 12.5, 3.7 mm Cursor: ABM1/ABM2 = 32.37 dB ABM1 comp = -9.08 dBA/m BWC Factor = 0.14 dB Location: 8.3, 12.5, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 113 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.68 802_11n20 MCS3 EVS wb 5_9 157ch Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5785 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 50.05 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.46 dB Location: 8.5, 12.7, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 114 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.69 802_11n20 MCS3 EVS wb 5_9 157ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5785 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 16.48 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -18.18 dBA/m BWC Factor = 0.14 dB Location: 0, 0, 3.7 mm Cursor: ABM2 = -45.45 dBA/m Location: 0, 0, 3.7 mm Cursor: ABM1/ABM2 = 27.27 dB ABM1 comp = -18.18 dBA/m BWC Factor = 0.14 dB Location: 0, 0, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 115 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.70 802_11n20 MCS3 EVS wb 5_9 36ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5180 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 16.48 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -7.77 dBA/m BWC Factor = 0.14 dB Location: 0, 8.3, 3.7 mm Cursor: ABM2 = -42.04 dBA/m Location: 0, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 34.27 dB ABM1 comp = -7.77 dBA/m BWC Factor = 0.14 dB Location: 0, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 116 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.71 802_11n20 MCS3 EVS wb 5_9 36ch Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5180 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 50.05 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 1.74 dB BWC Factor = 9.46 dB Location: 0.4, 8.3, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 117 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.72 802_11n20 MCS3 EVS wb 5_9 36ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5180 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 16.48 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -19.78 dBA/m BWC Factor = 0.14 dB Location: 0, 20.8, 3.7 mm Cursor: ABM2 = -47.52 dBA/m Location: 0, 20.8, 3.7 mm Cursor: ABM1/ABM2 = 27.74 dB ABM1 comp = -19.78 dBA/m BWC Factor = 0.14 dB Location: 0, 20.8, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 118 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.73 802_11n20 MCS3 EVS wb 5_9 48ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5240 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 16.48 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -9.96 dBA/m BWC Factor = 0.14 dB Location: 4.2, 4.2, 3.7 mm Cursor: ABM2 = -41.78 dBA/m Location: 4.2, 4.2, 3.7 mm Cursor: ABM1/ABM2 = 31.82 dB ABM1 comp = -9.96 dBA/m BWC Factor = 0.14 dB Location: 4.2, 4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 119 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.74 802_11n20 MCS3 EVS wb 5_9 48ch Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5240 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 50.05 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 1.89 dB BWC Factor = 9.46 dB Location: 9.8, 8.5, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 120 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.75 802_11n20 MCS3 EVS wb 5_9 48ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5240 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 16.48 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -21.36 dBA/m BWC Factor = 0.14 dB Location: -4.2, 20.8, 3.7 mm Cursor: ABM2 = -50.59 dBA/m Location: -4.2, 20.8, 3.7 mm Cursor: ABM1/ABM2 = 29.23 dB ABM1 comp = -21.36 dBA/m BWC Factor = 0.14 dB Location: -4.2, 20.8, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 121 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.76 GSM850 190ch bit rate 6 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, GSM850 EDGE 2TX (0); Frequency: 836.6 MHz;Duty Cycle: 1:4.14954 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 3000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -4.11 dBA/m BWC Factor = 0.14 dB Location: 8.3, 4.2, 3.7 mm Cursor: ABM2 = -36.33 dBA/m Location: 8.3, 4.2, 3.7 mm Cursor: ABM1/ABM2 = 32.22 dB ABM1 comp = -4.11 dBA/m BWC Factor = 0.14 dB Location: 8.3, 4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 122 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.77 GSM850 190ch bit rate 6 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, GSM850 EDGE 2TX (0); Frequency: 836.6 MHz;Duty Cycle: 1:4.14954 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 61.5 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.45 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.45 dB Location: 8.2, 4.8, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 123 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.78 GSM850 190ch bit rate 6 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, GSM850 EDGE 2TX (0); Frequency: 836.6 MHz;Duty Cycle: 1:4.14954 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 3000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -20.54 dBA/m BWC Factor = 0.14 dB Location: -8.3, -4.2, 3.7 mm Cursor: ABM2 = -51.62 dBA/m Location: -8.3, -4.2, 3.7 mm Cursor: ABM1/ABM2 = 31.08 dB ABM1 comp = -20.54 dBA/m BWC Factor = 0.14 dB Location: -8.3, -4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 124 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.79 GSM1900 661ch bit rate 6 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, GSM 1900 2TX (0); Frequency: 1880 MHz;Duty Cycle: 1:4.14954 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 3000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -3.33 dBA/m BWC Factor = 0.14 dB Location: 8.3, 4.2, 3.7 mm Cursor: ABM2 = -35.41 dBA/m Location: 8.3, 4.2, 3.7 mm Cursor: ABM1/ABM2 = 32.07 dB ABM1 comp = -3.33 dBA/m BWC Factor = 0.14 dB Location: 8.3, 4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 125 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.80 GSM1900 661ch bit rate 6 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, GSM 1900 2TX (0); Frequency: 1880 MHz;Duty Cycle: 1:4.14954 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 61.5 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.45 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.45 dB Location: 8.2, 4.6, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 126 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.81 GSM1900 661ch bit rate 6 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, GSM 1900 2TX (0); Frequency: 1880 MHz;Duty Cycle: 1:4.14954 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 3000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -16.50 dBA/m BWC Factor = 0.14 dB Location: -4.2, -4.2, 3.7 mm Cursor: ABM2 = -47.78 dBA/m Location: -4.2, -4.2, 3.7 mm Cursor: ABM1/ABM2 = 31.29 dB ABM1 comp = -16.50 dBA/m BWC Factor = 0.14 dB Location: -4.2, -4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 127 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.82 WCDMA 1900 9400ch bit rate 6 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, WCDMA1900 (0); Frequency: 1880 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.15 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -1.23 dBA/m BWC Factor = 0.15 dB Location: 8.3, 8.3, 3.7 mm Cursor: ABM2 = -50.41 dBA/m Location: 8.3, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 49.19 dB ABM1 comp = -1.23 dBA/m BWC Factor = 0.15 dB Location: 8.3, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 128 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.83 WCDMA 1900 9400ch bit rate 6 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, WCDMA1900 (0); Frequency: 1880 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 61.5 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.46 dB Location: 8, 9.7, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 129 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.84 WCDMA 1900 9400ch bit rate 6 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, WCDMA1900 (0); Frequency: 1880 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.15 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -10.48 dBA/m BWC Factor = 0.15 dB Location: 0, 20.8, 3.7 mm Cursor: ABM2 = -51.42 dBA/m Location: 0, 20.8, 3.7 mm Cursor: ABM1/ABM2 = 40.94 dB ABM1 comp = -10.48 dBA/m BWC Factor = 0.15 dB Location: 0, 20.8, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 130 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.85 WCDMA 1700 1412ch bit rate 6 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, WCDMA IV (0); Frequency: 1732.4 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.15 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -1.15 dBA/m BWC Factor = 0.15 dB Location: 8.3, 8.3, 3.7 mm Cursor: ABM2 = -50.37 dBA/m Location: 8.3, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 49.22 dB ABM1 comp = -1.15 dBA/m BWC Factor = 0.15 dB Location: 8.3, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 131 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.86 WCDMA 1700 1412ch bit rate 6 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, WCDMA IV (0); Frequency: 1732.4 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 61.5 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.46 dB Location: 7.9, 9.5, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 132 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.87 WCDMA 1700 1412ch bit rate 6 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, WCDMA IV (0); Frequency: 1732.4 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.15 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -10.23 dBA/m BWC Factor = 0.15 dB Location: 0, 16.7, 3.7 mm Cursor: ABM2 = -51.08 dBA/m Location: 0, 16.7, 3.7 mm Cursor: ABM1/ABM2 = 40.85 dB ABM1 comp = -10.23 dBA/m BWC Factor = 0.15 dB Location: 0, 16.7, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 133 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.88 WCDMA 850 4183ch bit rate 6 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, WCDMA850 (0); Frequency: 836.6 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -7.86 dBA/m BWC Factor = 0.14 dB Location: 12.5, 12.5, 3.7 mm Cursor: ABM2 = -53.11 dBA/m Location: 12.5, 12.5, 3.7 mm Cursor: ABM1/ABM2 = 45.24 dB ABM1 comp = -7.86 dBA/m BWC Factor = 0.14 dB Location: 12.5, 12.5, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 134 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.89 WCDMA 850 4183ch bit rate 6 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, WCDMA850 (0); Frequency: 836.6 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 61.5 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.45 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.45 dB Location: 11.6, 12.1, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 135 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.90 WCDMA 850 4183ch bit rate 6 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, WCDMA850 (0); Frequency: 836.6 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -13.77 dBA/m BWC Factor = 0.14 dB Location: 0, 16.7, 3.7 mm Cursor: ABM2 = -49.67 dBA/m Location: 0, 16.7, 3.7 mm Cursor: ABM1/ABM2 = 35.90 dB ABM1 comp = -13.77 dBA/m BWC Factor = 0.14 dB Location: 0, 16.7, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 136 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.91 LTE Band 26 16QAM 15MHz 1RB 0offset 26865ch bit rate 6 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 26 (0); Frequency: 831.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -6.46 dBA/m BWC Factor = 0.14 dB Location: 8.3, 4.2, 3.7 mm Cursor: ABM2 = -44.12 dBA/m Location: 8.3, 4.2, 3.7 mm Cursor: ABM1/ABM2 = 37.66 dB ABM1 comp = -6.46 dBA/m BWC Factor = 0.14 dB Location: 8.3, 4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 137 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.92 LTE Band 26 16QAM 15MHz 1RB 0offset 26865ch bit rate 6 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 26 (0); Frequency: 831.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 61.5 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.46 dB Location: 8.1, 4.5, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 138 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.93 LTE Band 26 16QAM 15MHz 1RB 0offset 26865ch bit rate 6 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 26 (0); Frequency: 831.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -17.67 dBA/m BWC Factor = 0.14 dB Location: -4.2, 0, 3.7 mm Cursor: ABM2 = -45.33 dBA/m Location: -4.2, 0, 3.7 mm Cursor: ABM1/ABM2 = 27.66 dB ABM1 comp = -17.67 dBA/m BWC Factor = 0.14 dB Location: -4.2, 0, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 139 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.94 LTE Band 7 16QAM 15MHz 1RB 0offset 21100ch bit rate 6 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 7 (0); Frequency: 2535 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -1.43 dBA/m BWC Factor = 0.14 dB Location: 8.3, 12.5, 3.7 mm Cursor: ABM2 = -48.68 dBA/m Location: 8.3, 12.5, 3.7 mm Cursor: ABM1/ABM2 = 47.24 dB ABM1 comp = -1.43 dBA/m BWC Factor = 0.14 dB Location: 8.3, 12.5, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 140 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.95 LTE Band 7 16QAM 15MHz 1RB 0offset 21100ch bit rate 6 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 7 (0); Frequency: 2535 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 61.5 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.46 dB Location: 8.1, 11.8, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 141 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.96 LTE Band 7 16QAM 15MHz 1RB 0offset 21100ch bit rate 6 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 7 (0); Frequency: 2535 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -10.31 dBA/m BWC Factor = 0.14 dB Location: 0, 16.7, 3.7 mm Cursor: ABM2 = -48.59 dBA/m Location: 0, 16.7, 3.7 mm Cursor: ABM1/ABM2 = 38.28 dB ABM1 comp = -10.31 dBA/m BWC Factor = 0.14 dB Location: 0, 16.7, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 142 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.97 LTE Band 25 16QAM 15MHz 1RB 0offset 26365ch bit rate 6 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 25 (0); Frequency: 1882.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -1.46 dBA/m BWC Factor = 0.14 dB Location: 8.3, 12.5, 3.7 mm Cursor: ABM2 = -47.43 dBA/m Location: 8.3, 12.5, 3.7 mm Cursor: ABM1/ABM2 = 45.97 dB ABM1 comp = -1.46 dBA/m BWC Factor = 0.14 dB Location: 8.3, 12.5, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 143 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.98 LTE Band 25 16QAM 15MHz 1RB 0offset 26365ch bit rate 6 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 25 (0); Frequency: 1882.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 61.5 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.46 dB Location: 8, 11.2, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 144 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.99 LTE Band 25 16QAM 15MHz 1RB 0offset 26365ch bit rate 6 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 25 (0); Frequency: 1882.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -10.42 dBA/m BWC Factor = 0.14 dB Location: 0, 16.7, 3.7 mm Cursor: ABM2 = -49.72 dBA/m Location: 0, 16.7, 3.7 mm Cursor: ABM1/ABM2 = 39.30 dB ABM1 comp = -10.42 dBA/m BWC Factor = 0.14 dB Location: 0, 16.7, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 145 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.100 LTE Band 66 16QAM 15MHz 1RB 0offset 132322ch bit rate 6 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 66 (0); Frequency: 1745 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -1.51 dBA/m BWC Factor = 0.14 dB Location: 8.3, 8.3, 3.7 mm Cursor: ABM2 = -42.34 dBA/m Location: 8.3, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 40.83 dB ABM1 comp = -1.51 dBA/m BWC Factor = 0.14 dB Location: 8.3, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 146 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.101 LTE Band 66 16QAM 15MHz 1RB 0offset 132322ch bit rate 6 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 66 (0); Frequency: 1745 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 61.5 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.46 dB Location: 8, 9.3, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 147 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.102 LTE Band 66 16QAM 15MHz 1RB 0offset 132322ch bit rate 6 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 66 (0); Frequency: 1745 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -13.64 dBA/m BWC Factor = 0.14 dB Location: -4.2, 0, 3.7 mm Cursor: ABM2 = -48.23 dBA/m Location: -4.2, 0, 3.7 mm Cursor: ABM1/ABM2 = 34.59 dB ABM1 comp = -13.64 dBA/m BWC Factor = 0.14 dB Location: -4.2, 0, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 148 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.103 LTE Band 71 16QAM 15MHz 1RB 0offset 133297ch bit rate 6 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE 71 (0); Frequency: 680.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -1.19 dBA/m BWC Factor = 0.14 dB Location: 4.2, 8.3, 3.7 mm Cursor: ABM2 = -36.48 dBA/m Location: 4.2, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 35.29 dB ABM1 comp = -1.19 dBA/m BWC Factor = 0.14 dB Location: 4.2, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 149 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.104 LTE Band 71 16QAM 15MHz 1RB 0offset 133297ch bit rate 6 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE 71 (0); Frequency: 680.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 61.5 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.46 dB Location: 4.2, 10, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 150 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.105 LTE Band 71 16QAM 15MHz 1RB 0offset 133297ch bit rate 6 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE 71 (0); Frequency: 680.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -15.15 dBA/m BWC Factor = 0.14 dB Location: -4.2, -4.2, 3.7 mm Cursor: ABM2 = -48.26 dBA/m Location: -4.2, -4.2, 3.7 mm Cursor: ABM1/ABM2 = 33.11 dB ABM1 comp = -15.15 dBA/m BWC Factor = 0.14 dB Location: -4.2, -4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 151 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.106 LTE Band 12 16QAM 5MHz 1RB 0offset 23095ch bit rate 6 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE 12 (0); Frequency: 707.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -1.09 dBA/m BWC Factor = 0.14 dB Location: 4.2, 8.3, 3.7 mm Cursor: ABM2 = -35.91 dBA/m Location: 4.2, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 34.82 dB ABM1 comp = -1.09 dBA/m BWC Factor = 0.14 dB Location: 4.2, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 152 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.107 LTE Band 12 16QAM 5MHz 1RB 0offset 23095ch bit rate 6 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE 12 (0); Frequency: 707.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 61.5 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.46 dB Location: 4.3, 8.8, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 153 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.108 LTE Band 12 16QAM 5MHz 1RB 0offset 23095ch bit rate 6 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE 12 (0); Frequency: 707.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -14.38 dBA/m BWC Factor = 0.14 dB Location: -4.2, -4.2, 3.7 mm Cursor: ABM2 = -47.14 dBA/m Location: -4.2, -4.2, 3.7 mm Cursor: ABM1/ABM2 = 32.76 dB ABM1 comp = -14.38 dBA/m BWC Factor = 0.14 dB Location: -4.2, -4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 154 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.109 LTE Band 13 16QAM 5MHz 1RB 0offset 23230ch bit rate 6 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 13 (0); Frequency: 782 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -1.24 dBA/m BWC Factor = 0.14 dB Location: 8.3, 8.3, 3.7 mm Cursor: ABM2 = -42.36 dBA/m Location: 8.3, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 41.12 dB ABM1 comp = -1.24 dBA/m BWC Factor = 0.14 dB Location: 8.3, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 155 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.110 LTE Band 13 16QAM 5MHz 1RB 0offset 23230ch bit rate 6 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 13 (0); Frequency: 782 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 61.5 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.46 dB Location: 8, 8.4, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 156 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.111 LTE Band 13 16QAM 5MHz 1RB 0offset 23230ch bit rate 6 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 13 (0); Frequency: 782 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -14.52 dBA/m BWC Factor = 0.14 dB Location: -4.2, -4.2, 3.7 mm Cursor: ABM2 = -48.37 dBA/m Location: -4.2, -4.2, 3.7 mm Cursor: ABM1/ABM2 = 33.86 dB ABM1 comp = -14.52 dBA/m BWC Factor = 0.14 dB Location: -4.2, -4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 157 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.112 LTE Band 14 16QAM 5MHz 1RB 0offset 23330ch bit rate 6 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE 14 (0); Frequency: 793 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -1.15 dBA/m BWC Factor = 0.14 dB Location: 8.3, 8.3, 3.7 mm Cursor: ABM2 = -43.74 dBA/m Location: 8.3, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 42.59 dB ABM1 comp = -1.15 dBA/m BWC Factor = 0.14 dB Location: 8.3, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 158 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.113 LTE Band 14 16QAM 5MHz 1RB 0offset 23330ch bit rate 6 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE 14 (0); Frequency: 793 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 61.5 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.46 dB Location: 8, 8.6, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 159 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.114 LTE Band 14 16QAM 5MHz 1RB 0offset 23330ch bit rate 6 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE 14 (0); Frequency: 793 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -13.37 dBA/m BWC Factor = 0.14 dB Location: -4.2, 0, 3.7 mm Cursor: ABM2 = -46.77 dBA/m Location: -4.2, 0, 3.7 mm Cursor: ABM1/ABM2 = 33.40 dB ABM1 comp = -13.37 dBA/m BWC Factor = 0.14 dB Location: -4.2, 0, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 160 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.115 LTE Band 30 16QAM 5MHz 1RB 0offset 27710ch bit rate 6 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE 30 (0); Frequency: 2310 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -1.06 dBA/m BWC Factor = 0.14 dB Location: 8.3, 8.3, 3.7 mm Cursor: ABM2 = -46.23 dBA/m Location: 8.3, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 45.17 dB ABM1 comp = -1.06 dBA/m BWC Factor = 0.14 dB Location: 8.3, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 161 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.116 LTE Band 30 16QAM 5MHz 1RB 0offset 27710ch bit rate 6 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE 30 (0); Frequency: 2310 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 61.5 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.46 dB Location: 8, 9, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 162 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.117 LTE Band 30 16QAM 5MHz 1RB 0offset 27710ch bit rate 6 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE 30 (0); Frequency: 2310 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -9.80 dBA/m BWC Factor = 0.14 dB Location: 0, 16.7, 3.7 mm Cursor: ABM2 = -46.13 dBA/m Location: 0, 16.7, 3.7 mm Cursor: ABM1/ABM2 = 36.33 dB ABM1 comp = -9.80 dBA/m BWC Factor = 0.14 dB Location: 0, 16.7, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 163 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.118 LTE Band 41 QPSK 5MHz 1RB 12offset 41093ch Config 0 6 bit rate 75 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 41 (FCC) (0); Frequency: 2640.3 MHz;Duty Cycle: 1:4 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.15 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -4.48 dBA/m BWC Factor = 0.15 dB Location: 8.3, 8.3, 3.7 mm Cursor: ABM2 = -36.79 dBA/m Location: 8.3, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 32.30 dB ABM1 comp = -4.48 dBA/m BWC Factor = 0.15 dB Location: 8.3, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 164 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.119 LTE Band 41 QPSK 5MHz 1RB 12offset 41093ch Config 0 6 bit rate 75 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 41 (FCC) (0); Frequency: 2640.3 MHz;Duty Cycle: 1:4 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 61.5 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.46 dB Location: 8, 9.9, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 165 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.120 LTE Band 41 QPSK 5MHz 1RB 12offset 41093ch Config 0 6 bit rate 75 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 41 (FCC) (0); Frequency: 2640.3 MHz;Duty Cycle: 1:4 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.15 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -21.46 dBA/m BWC Factor = 0.15 dB Location: -8.3, 0, 3.7 mm Cursor: ABM2 = -50.55 dBA/m Location: -8.3, 0, 3.7 mm Cursor: ABM1/ABM2 = 29.09 dB ABM1 comp = -21.46 dBA/m BWC Factor = 0.15 dB Location: -8.3, 0, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 166 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.121 LTE Band 38 QPSK 5MHz 1RB 12offset 38000ch Config 0 6 Bit rate 75 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 38 (0); Frequency: 2595 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -0.98 dBA/m BWC Factor = 0.14 dB Location: 8.3, 8.3, 3.7 mm Cursor: ABM2 = -40.83 dBA/m Location: 8.3, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 39.85 dB ABM1 comp = -0.98 dBA/m BWC Factor = 0.14 dB Location: 8.3, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 167 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.122 LTE Band 38 QPSK 5MHz 1RB 12offset 38000ch Config 0 6 Bit rate 75 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 38 (0); Frequency: 2595 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 61.5 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.46 dB Location: 8.1, 8.7, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 168 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.123 LTE Band 38 QPSK 5MHz 1RB 12offset 38000ch Config 0 6 Bit rate 75 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 38 (0); Frequency: 2595 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -14.13 dBA/m BWC Factor = 0.14 dB Location: -4.2, -4.2, 3.7 mm Cursor: ABM2 = -47.53 dBA/m Location: -4.2, -4.2, 3.7 mm Cursor: ABM1/ABM2 = 33.40 dB ABM1 comp = -14.13 dBA/m BWC Factor = 0.14 dB Location: -4.2, -4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 169 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.124 LTE Band 40 QPSK 5MHz 1RB 12offset 38775ch Config 0 6 Bit rate 75 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 40 (0); Frequency: 2312.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = 1.09 dBA/m BWC Factor = 0.14 dB Location: 8.3, 8.3, 3.7 mm Cursor: ABM2 = -41.38 dBA/m Location: 8.3, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 42.47 dB ABM1 comp = 1.09 dBA/m BWC Factor = 0.14 dB Location: 8.3, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 170 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.125 LTE Band 40 QPSK 5MHz 1RB 12offset 38775ch Config 0 6 Bit rate 75 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 40 (0); Frequency: 2312.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 61.5 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.45 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.45 dB Location: 8.2, 5.9, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 171 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.126 LTE Band 40 QPSK 5MHz 1RB 12offset 38775ch Config 0 6 Bit rate 75 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 40 (0); Frequency: 2312.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -15.04 dBA/m BWC Factor = 0.14 dB Location: -4.2, -4.2, 3.7 mm Cursor: ABM2 = -50.85 dBA/m Location: -4.2, -4.2, 3.7 mm Cursor: ABM1/ABM2 = 35.81 dB ABM1 comp = -15.04 dBA/m BWC Factor = 0.14 dB Location: -4.2, -4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 172 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.127 LTE Band 40 QPSK 5MHz 1RB 12offset 39225ch Config 0 6 Bit rate 75 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 40 (0); Frequency: 2357.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = 0.58 dBA/m BWC Factor = 0.14 dB Location: 8.3, 8.3, 3.7 mm Cursor: ABM2 = -42.20 dBA/m Location: 8.3, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 42.77 dB ABM1 comp = 0.58 dBA/m BWC Factor = 0.14 dB Location: 8.3, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 173 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.128 LTE Band 40 QPSK 5MHz 1RB 12offset 39225ch Config 0 6 Bit rate 75 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 40 (0); Frequency: 2357.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 61.5 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.45 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.45 dB Location: 8.2, 6.3, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 174 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.129 LTE Band 40 QPSK 5MHz 1RB 12offset 39225ch Config 0 6 Bit rate 75 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE Band 40 (0); Frequency: 2357.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -11.55 dBA/m BWC Factor = 0.14 dB Location: 0, -4.2, 3.7 mm Cursor: ABM2 = -47.46 dBA/m Location: 0, -4.2, 3.7 mm Cursor: ABM1/ABM2 = 35.91 dB ABM1 comp = -11.55 dBA/m BWC Factor = 0.14 dB Location: 0, -4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 175 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.130 802_11b 1Mbps 1ch Bit rate 6 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, 2450MHz FCC (0); Frequency: 2412 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -11.96 dBA/m BWC Factor = 0.14 dB Location: 12.5, 8.3, 3.7 mm Cursor: ABM2 = -38.33 dBA/m Location: 12.5, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 26.37 dB ABM1 comp = -11.96 dBA/m BWC Factor = 0.14 dB Location: 12.5, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 176 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.131 802_11b 1Mbps 1ch Bit rate 6 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, 2450MHz FCC (0); Frequency: 2412 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 61.5 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.46 dB Location: 12.5, 7.5, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 177 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.132 802_11b 1Mbps 1ch Bit rate 6 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, 2450MHz FCC (0); Frequency: 2412 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -13.43 dBA/m BWC Factor = 0.14 dB Location: 0, 0, 3.7 mm Cursor: ABM2 = -45.14 dBA/m Location: 0, 0, 3.7 mm Cursor: ABM1/ABM2 = 31.71 dB ABM1 comp = -13.43 dBA/m BWC Factor = 0.14 dB Location: 0, 0, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 178 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.133 802_11n20 MCS3 40ch Bit rate 40 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5200 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -3.99 dBA/m BWC Factor = 0.14 dB Location: 4.2, 8.3, 3.7 mm Cursor: ABM2 = -45.30 dBA/m Location: 4.2, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 41.30 dB ABM1 comp = -3.99 dBA/m BWC Factor = 0.14 dB Location: 4.2, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 179 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.134 802_11n20 MCS3 40ch Bit rate 40 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5200 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 61.5 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.45 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.45 dB Location: 6.5, 9.2, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 180 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.135 802_11n20 MCS3 40ch Bit rate 40 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5200 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -13.46 dBA/m BWC Factor = 0.14 dB Location: 0, 16.7, 3.7 mm Cursor: ABM2 = -50.57 dBA/m Location: 0, 16.7, 3.7 mm Cursor: ABM1/ABM2 = 37.11 dB ABM1 comp = -13.46 dBA/m BWC Factor = 0.14 dB Location: 0, 16.7, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 181 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.136 802_11n20 MCS3 56ch Bit rate 40 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5280 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -1.40 dBA/m BWC Factor = 0.14 dB Location: 8.3, 12.5, 3.7 mm Cursor: ABM2 = -44.52 dBA/m Location: 8.3, 12.5, 3.7 mm Cursor: ABM1/ABM2 = 43.12 dB ABM1 comp = -1.40 dBA/m BWC Factor = 0.14 dB Location: 8.3, 12.5, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 182 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.137 802_11n20 MCS3 56ch Bit rate 40 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5280 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 61.5 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.46 dB Location: 7.3, 12, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 183 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.138 802_11n20 MCS3 56ch Bit rate 40 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5280 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -9.40 dBA/m BWC Factor = 0.14 dB Location: 0, 16.7, 3.7 mm Cursor: ABM2 = -48.20 dBA/m Location: 0, 16.7, 3.7 mm Cursor: ABM1/ABM2 = 38.80 dB ABM1 comp = -9.40 dBA/m BWC Factor = 0.14 dB Location: 0, 16.7, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 184 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.139 802_11n20 MCS3 120ch Bit rate 40 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5600 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -0.51 dBA/m BWC Factor = 0.14 dB Location: 4.2, 8.3, 3.7 mm Cursor: ABM2 = -44.50 dBA/m Location: 4.2, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 43.98 dB ABM1 comp = -0.51 dBA/m BWC Factor = 0.14 dB Location: 4.2, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 185 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.140 802_11n20 MCS3 120ch Bit rate 40 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5600 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 61.5 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.46 dB Location: 5, 9.5, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 186 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.141 802_11n20 MCS3 120ch Bit rate 40 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5600 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -13.06 dBA/m BWC Factor = 0.14 dB Location: -4.2, 16.7, 3.7 mm Cursor: ABM2 = -51.28 dBA/m Location: -4.2, 16.7, 3.7 mm Cursor: ABM1/ABM2 = 38.22 dB ABM1 comp = -13.06 dBA/m BWC Factor = 0.14 dB Location: -4.2, 16.7, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 187 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.142 802_11n20 MCS3 157ch Bit rate 40 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5785 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -1.45 dBA/m BWC Factor = 0.14 dB Location: 8.3, 12.5, 3.7 mm Cursor: ABM2 = -45.91 dBA/m Location: 8.3, 12.5, 3.7 mm Cursor: ABM1/ABM2 = 44.46 dB ABM1 comp = -1.45 dBA/m BWC Factor = 0.14 dB Location: 8.3, 12.5, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 188 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.143 802_11n20 MCS3 157ch Bit rate 40 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5785 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 61.5 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: 9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 2.00 dB BWC Factor = 9.46 dB Location: 7.5, 10.7, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 189 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.144 802_11n20 MCS3 157ch Bit rate 40 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, WIFI 5GHz (0); Frequency: 5785 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: 0.14 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -12.80 dBA/m BWC Factor = 0.14 dB Location: -4.2, 16.7, 3.7 mm Cursor: ABM2 = -50.43 dBA/m Location: -4.2, 16.7, 3.7 mm Cursor: ABM1/ABM2 = 37.63 dB ABM1 comp = -12.80 dBA/m BWC Factor = 0.14 dB Location: -4.2, 16.7, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 190 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.145 1x EVDO BC0 384ch bit rate 40 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, CDMA 835MHz FCC (0); Frequency: 836.52 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.63 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: -18.78 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = 5.75 dBA/m BWC Factor = -18.78 dB Location: 8.3, 8.3, 3.7 mm Cursor: ABM2 = -20.11 dBA/m Location: 8.3, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 25.86 dB ABM1 comp = 5.75 dBA/m BWC Factor = -18.78 dB Location: 8.3, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 191 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.146 1x EVDO BC0 384ch bit rate 40 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, CDMA 835MHz FCC (0); Frequency: 836.52 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 55.85 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: -9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 1.54 dB BWC Factor = -9.46 dB Location: 8.1, 8, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 192 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.147 1x EVDO BC0 384ch bit rate 40 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, CDMA 835MHz FCC (0); Frequency: 836.52 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.63 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: -18.78 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -4.61 dBA/m BWC Factor = -18.78 dB Location: 8.3, 12.5, 3.7 mm Cursor: ABM2 = -28.25 dBA/m Location: 8.3, 12.5, 3.7 mm Cursor: ABM1/ABM2 = 23.64 dB ABM1 comp = -4.61 dBA/m BWC Factor = -18.78 dB Location: 8.3, 12.5, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 193 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.148 1x EVDO BC1 600ch bit rate 40 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, CDMA BC1 EVDO(1900MHz) (0); Frequency: 1880 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.63 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: -18.78 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = 3.92 dBA/m BWC Factor = -18.78 dB Location: 8.3, 8.3, 3.7 mm Cursor: ABM2 = -27.71 dBA/m Location: 8.3, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 31.63 dB ABM1 comp = 3.92 dBA/m BWC Factor = -18.78 dB Location: 8.3, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 194 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.149 1x EVDO BC1 600ch bit rate 40 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, CDMA BC1 EVDO(1900MHz) (0); Frequency: 1880 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 55.85 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: -9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 1.39 dB BWC Factor = -9.46 dB Location: 8.4, 7.8, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 195 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.150 1x EVDO BC1 600ch bit rate 40 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, CDMA BC1 EVDO(1900MHz) (0); Frequency: 1880 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.63 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: -18.78 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -4.47 dBA/m BWC Factor = -18.78 dB Location: 0, 16.7, 3.7 mm Cursor: ABM2 = -27.56 dBA/m Location: 0, 16.7, 3.7 mm Cursor: ABM1/ABM2 = 23.09 dB ABM1 comp = -4.47 dBA/m BWC Factor = -18.78 dB Location: 0, 16.7, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 196 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.151 1x EVDO BC10 670ch bit rate 40 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, CDMA 835MHz FCC (0); Frequency: 822.75 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.63 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: -18.77 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = 5.54 dBA/m BWC Factor = -18.77 dB Location: 8.3, 8.3, 3.7 mm Cursor: ABM2 = -24.56 dBA/m Location: 8.3, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 30.10 dB ABM1 comp = 5.54 dBA/m BWC Factor = -18.77 dB Location: 8.3, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 197 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.152 1x EVDO BC10 670ch bit rate 40 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, CDMA 835MHz FCC (0); Frequency: 822.75 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 55.85 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: -9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 1.06 dB BWC Factor = -9.46 dB Location: 8.2, 6.1, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 198 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.153 1x EVDO BC10 670ch bit rate 40 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, CDMA 835MHz FCC (0); Frequency: 822.75 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.63 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: -18.77 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -4.04 dBA/m BWC Factor = -18.77 dB Location: 0, 16.7, 3.7 mm Cursor: ABM2 = -27.14 dBA/m Location: 0, 16.7, 3.7 mm Cursor: ABM1/ABM2 = 23.10 dB ABM1 comp = -4.04 dBA/m BWC Factor = -18.77 dB Location: 0, 16.7, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 199 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.154 1x EVDO BC1 25ch bit rate 40 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, CDMA BC1 EVDO(1900MHz) (0); Frequency: 1851.25 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.63 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: -18.77 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = 5.91 dBA/m BWC Factor = -18.77 dB Location: 8.3, 8.3, 3.7 mm Cursor: ABM2 = -28.09 dBA/m Location: 8.3, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 34.00 dB ABM1 comp = 5.91 dBA/m BWC Factor = -18.77 dB Location: 8.3, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 200 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.155 1x EVDO BC1 25ch bit rate 40 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, CDMA BC1 EVDO(1900MHz) (0); Frequency: 1851.25 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 55.85 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: -9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 1.44 dB BWC Factor = -9.46 dB Location: 11.3, 10, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 201 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.156 1x EVDO BC1 25ch bit rate 40 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, CDMA BC1 EVDO(1900MHz) (0); Frequency: 1851.25 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.63 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: -18.77 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -4.87 dBA/m BWC Factor = -18.77 dB Location: 0, 16.7, 3.7 mm Cursor: ABM2 = -28.90 dBA/m Location: 0, 16.7, 3.7 mm Cursor: ABM1/ABM2 = 24.03 dB ABM1 comp = -4.87 dBA/m BWC Factor = -18.77 dB Location: 0, 16.7, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 202 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.157 1x EVDO BC1 1175ch bit rate 40 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, CDMA BC1 EVDO(1900MHz) (0); Frequency: 1908.75 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.63 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: -18.77 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = 4.22 dBA/m BWC Factor = -18.77 dB Location: 12.5, 8.3, 3.7 mm Cursor: ABM2 = -29.96 dBA/m Location: 12.5, 8.3, 3.7 mm Cursor: ABM1/ABM2 = 34.18 dB ABM1 comp = 4.22 dBA/m BWC Factor = -18.77 dB Location: 12.5, 8.3, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 203 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.158 1x EVDO BC1 1175ch bit rate 40 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, CDMA BC1 EVDO(1900MHz) (0); Frequency: 1908.75 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 55.85 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: -9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 1.38 dB BWC Factor = -9.46 dB Location: 11.3, 9, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 204 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.159 1x EVDO BC1 1175ch bit rate 40 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, CDMA BC1 EVDO(1900MHz) (0); Frequency: 1908.75 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.63 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: -18.77 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -5.12 dBA/m BWC Factor = -18.77 dB Location: 0, 16.7, 3.7 mm Cursor: ABM2 = -28.42 dBA/m Location: 0, 16.7, 3.7 mm Cursor: ABM1/ABM2 = 23.30 dB ABM1 comp = -5.12 dBA/m BWC Factor = -18.77 dB Location: 0, 16.7, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 205 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.160 CDMA BC0 384 EVRC-B SO68 RC1 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, CDMA 835MHz FCC (0); Frequency: 836.52 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.63 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: -18.77 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = 1.93 dBA/m BWC Factor = -18.77 dB Location: 8.3, 4.2, 3.7 mm Cursor: ABM2 = -22.38 dBA/m Location: 8.3, 4.2, 3.7 mm Cursor: ABM1/ABM2 = 24.31 dB ABM1 comp = 1.93 dBA/m BWC Factor = -18.77 dB Location: 8.3, 4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 206 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.161 CDMA BC0 384 EVRC-B SO68 RC1 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, CDMA 835MHz FCC (0); Frequency: 836.52 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 55.85 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: -9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 1.23 dB BWC Factor = -9.46 dB Location: 7.9, 4.8, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 207 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.162 CDMA BC0 384 EVRC-B SO68 RC1 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, CDMA 835MHz FCC (0); Frequency: 836.52 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.63 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: -18.77 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -5.50 dBA/m BWC Factor = -18.77 dB Location: 0, -4.2, 3.7 mm Cursor: ABM2 = -29.49 dBA/m Location: 0, -4.2, 3.7 mm Cursor: ABM1/ABM2 = 23.99 dB ABM1 comp = -5.50 dBA/m BWC Factor = -18.77 dB Location: 0, -4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 208 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.163 CDMA BC1 600 EVRC-B SO68 RC1 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, CDMA BC1 EVDO(1900MHz) (0); Frequency: 1880 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.63 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: -18.78 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = 4.17 dBA/m BWC Factor = -18.78 dB Location: 8.3, 4.2, 3.7 mm Cursor: ABM2 = -29.46 dBA/m Location: 8.3, 4.2, 3.7 mm Cursor: ABM1/ABM2 = 33.63 dB ABM1 comp = 4.17 dBA/m BWC Factor = -18.78 dB Location: 8.3, 4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 209 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.164 CDMA BC1 600 EVRC-B SO68 RC1 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, CDMA BC1 EVDO(1900MHz) (0); Frequency: 1880 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 55.85 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: -9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 1.64 dB BWC Factor = -9.46 dB Location: 8.2, 4.9, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 210 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.165 CDMA BC1 600 EVRC-B SO68 RC1 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, CDMA BC1 EVDO(1900MHz) (0); Frequency: 1880 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.63 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: -18.78 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -7.54 dBA/m BWC Factor = -18.78 dB Location: 0, -4.2, 3.7 mm Cursor: ABM2 = -33.03 dBA/m Location: 0, -4.2, 3.7 mm Cursor: ABM1/ABM2 = 25.49 dB ABM1 comp = -7.54 dBA/m BWC Factor = -18.78 dB Location: 0, -4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 211 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.166 CDMA BC10 560 EVRC-B SO68 RC1 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, BC10 (0); Frequency: 820 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.63 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: -18.77 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = 3.77 dBA/m BWC Factor = -18.77 dB Location: 8.3, 4.2, 3.7 mm Cursor: ABM2 = -20.30 dBA/m Location: 8.3, 4.2, 3.7 mm Cursor: ABM1/ABM2 = 24.07 dB ABM1 comp = 3.77 dBA/m BWC Factor = -18.77 dB Location: 8.3, 4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 212 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.167 CDMA BC10 560 EVRC-B SO68 RC1 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, BC10 (0); Frequency: 820 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 55.85 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: -9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 1.55 dB BWC Factor = -9.46 dB Location: 8.3, 4.1, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 213 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.168 CDMA BC10 560 EVRC-B SO68 RC1 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, BC10 (0); Frequency: 820 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.63 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: -18.77 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -7.41 dBA/m BWC Factor = -18.77 dB Location: 0, -4.2, 3.7 mm Cursor: ABM2 = -31.05 dBA/m Location: 0, -4.2, 3.7 mm Cursor: ABM1/ABM2 = 23.64 dB ABM1 comp = -7.41 dBA/m BWC Factor = -18.77 dB Location: 0, -4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 214 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.169 CDMA BC10 450 EVRC-B SO68 RC1 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, BC10 (0); Frequency: 817.25 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.63 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: -18.78 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = 3.82 dBA/m BWC Factor = -18.78 dB Location: 8.3, 4.2, 3.7 mm Cursor: ABM2 = -20.98 dBA/m Location: 8.3, 4.2, 3.7 mm Cursor: ABM1/ABM2 = 24.80 dB ABM1 comp = 3.82 dBA/m BWC Factor = -18.78 dB Location: 8.3, 4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 215 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.170 CDMA BC10 450 EVRC-B SO68 RC1 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, BC10 (0); Frequency: 817.25 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 55.85 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: -9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 1.61 dB BWC Factor = -9.46 dB Location: 8.3, 3.9, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 216 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.171 CDMA BC10 450 EVRC-B SO68 RC1 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, BC10 (0); Frequency: 817.25 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.63 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: -18.78 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -7.74 dBA/m BWC Factor = -18.78 dB Location: 0, -4.2, 3.7 mm Cursor: ABM2 = -31.81 dBA/m Location: 0, -4.2, 3.7 mm Cursor: ABM1/ABM2 = 24.07 dB ABM1 comp = -7.74 dBA/m BWC Factor = -18.78 dB Location: 0, -4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 217 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.172 CDMA BC10 670 EVRC-B SO68 RC1 z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, BC10 (0); Frequency: 822.75 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.63 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: -18.77 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = 4.09 dBA/m BWC Factor = -18.77 dB Location: 8.3, 4.2, 3.7 mm Cursor: ABM2 = -19.22 dBA/m Location: 8.3, 4.2, 3.7 mm Cursor: ABM1/ABM2 = 23.31 dB ABM1 comp = 4.09 dBA/m BWC Factor = -18.77 dB Location: 8.3, 4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 218 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.173 CDMA BC10 670 EVRC-B SO68 RC1 Freq. Response DUT: SM-A516U; Type: Bar Communication System: UID 0, BC10 (0); Frequency: 822.75 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) wideband at best S/N/ABM Freq Resp(x,y,z,f) (1x1x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_Normal_51s new.wav Output Gain: 55.85 Measure Window Start: 300ms Measure Window Length: 51000ms BWC applied: -9.46 dB Device Reference Point: 0, 0, -6.3 mm Category Category T1 Category T2 Category T3 Category T4 Cursor: Diff = 1.71 dB BWC Factor = -9.46 dB Location: 8.3, 3.7, 3.7 mm Telephone parameters WD signal quality [(signal+noise)-to-noise ratio in decibels] 0 dB to 10 dB 10 dB to 20 dB 20 dB to 30 dB > 30 dB F-TP22-03 (Rev.00) 219 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.174 CDMA BC10 670 EVRC-B SO68 RC1 y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, BC10 (0); Frequency: 822.75 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY Configuration: Probe: AM1DV2 - 1013; ; Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Signal(x,y,z) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.63 Measure Window Start: 300ms Measure Window Length: 1000ms BWC applied: -18.77 dB Device Reference Point: 0, 0, -6.3 mm Cursor: ABM1 comp = -5.19 dBA/m BWC Factor = -18.77 dB Location: 4.2, -4.2, 3.7 mm Cursor: ABM2 = -28.29 dBA/m Location: 4.2, -4.2, 3.7 mm Cursor: ABM1/ABM2 = 23.11 dB ABM1 comp = -5.19 dBA/m BWC Factor = -18.77 dB Location: 4.2, -4.2, 3.7 mm 0 dB = 1.000 A/m = 0.00 dBA/m F-TP22-03 (Rev.00) 220 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.175 NR Band66 DFT-s-OFDM BPSK 20MHz 1RB 104offset 349000ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, n66 (0); Frequency: 1745 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3049; ; Calibrated: 2020-05-26 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -34.42 dBA/m Location: 8.3, 8.3, 3.7 mm F-TP22-03 (Rev.00) 221 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.176 NR Band66 DFT-s-OFDM BPSK 20MHz 1RB 104offset 349000ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, n66 (0); Frequency: 1745 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3049; ; Calibrated: 2020-05-26 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -46.19 dBA/m Location: -8.3, 0, 3.7 mm F-TP22-03 (Rev.00) 222 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.177 NR Band71 DFT-s-OFDM BPSK 20MHz 1RB 104offset 1361000ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE 71 (0); Frequency: 680.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3049; ; Calibrated: 2020-05-26 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -47.05 dBA/m Location: 8.3, 8.3, 3.7 mm F-TP22-03 (Rev.00) 223 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.178 NR Band71 DFT-s-OFDM BPSK 20MHz 1RB 104offset 1361000ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, LTE 71 (0); Frequency: 680.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3049; ; Calibrated: 2020-05-26 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -46.79 dBA/m Location: -8.3, 0, 3.7 mm F-TP22-03 (Rev.00) 224 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.179 NR Band5 DFT-s-OFDM BPSK 20MHz 1RB 104offset 167300ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, n5; Frequency: 836.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3049; ; Calibrated: 2020-05-26 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -40.80 dBA/m Location: 8.3, 8.3, 3.7 mm F-TP22-03 (Rev.00) 225 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.180 NR Band5 DFT-s-OFDM BPSK 20MHz 1RB 104offset 167300ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, n5; Frequency: 836.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3049; ; Calibrated: 2020-05-26 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -46.39 dBA/m Location: -8.3, 0, 3.7 mm F-TP22-03 (Rev.00) 226 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.181 NR Band2 DFT-s-OFDM BPSK 20MHz 1RB 104offset 1361000ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, n2; Frequency: 1880 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3049; ; Calibrated: 2020-05-26 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -42.02 dBA/m Location: 8.3, 8.3, 3.7 mm F-TP22-03 (Rev.00) 227 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.182 NR Band2 DFT-s-OFDM BPSK 20MHz 1RB 104offset 1361000ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, n2; Frequency: 1880 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3049; ; Calibrated: 2020-05-26 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -46.65 dBA/m Location: -8.3, 0, 3.7 mm F-TP22-03 (Rev.00) 228 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.183 NR Band66 DFT-s-OFDM BPSK 5MHz 1RB 23offset 351160ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, n66 (0); Frequency: 1755.8 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3049; ; Calibrated: 2020-05-26 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -45.00 dBA/m Location: 8.3, 8.3, 3.7 mm F-TP22-03 (Rev.00) 229 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.184 NR Band66 DFT-s-OFDM BPSK 5MHz 1RB 23offset 351160ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, n66 (0); Frequency: 1755.8 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3049; ; Calibrated: 2020-05-26 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -46.86 dBA/m Location: -8.3, 0, 3.7 mm F-TP22-03 (Rev.00) 230 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.185 NR Band66 DFT-s-OFDM BPSK 10MHz 1RB 50offset 351000ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, n66 (0); Frequency: 1755 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3049; ; Calibrated: 2020-05-26 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -44.58 dBA/m Location: 8.3, 8.3, 3.7 mm F-TP22-03 (Rev.00) 231 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.186 NR Band66 DFT-s-OFDM BPSK 10MHz 1RB 50offset 351000ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, n66 (0); Frequency: 1755 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3049; ; Calibrated: 2020-05-26 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -46.78 dBA/m Location: -8.3, 0, 3.7 mm F-TP22-03 (Rev.00) 232 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.187 NR Band66 DFT-s-OFDM BPSK 15MHz 1RB 77offset 350820ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, n66 (0); Frequency: 1754.1 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3049; ; Calibrated: 2020-05-26 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -44.89 dBA/m Location: 8.3, 8.3, 3.7 mm F-TP22-03 (Rev.00) 233 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.188 NR Band66 DFT-s-OFDM BPSK 15MHz 1RB 77offset 350820ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, n66 (0); Frequency: 1754.1 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3049; ; Calibrated: 2020-05-26 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -46.80 dBA/m Location: -8.3, 0, 3.7 mm F-TP22-03 (Rev.00) 234 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.189 NR Band66 DFT-s-OFDM BPSK 20MHz 1RB 104offset 344000ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, n66 (0); Frequency: 1720 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3049; ; Calibrated: 2020-05-26 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -44.52 dBA/m Location: 8.3, 8.3, 3.7 mm F-TP22-03 (Rev.00) 235 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.190 NR Band66 DFT-s-OFDM BPSK 20MHz 1RB 104offset 344000ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, n66 (0); Frequency: 1720 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3049; ; Calibrated: 2020-05-26 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -46.71 dBA/m Location: -8.3, 0, 3.7 mm F-TP22-03 (Rev.00) 236 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.191 NR Band66 DFT-s-OFDM BPSK 20MHz 1RB 104offset 351500ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, n66 (0); Frequency: 1757.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3049; ; Calibrated: 2020-05-26 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -44.15 dBA/m Location: 8.3, 8.3, 3.7 mm F-TP22-03 (Rev.00) 237 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.192 NR Band66 DFT-s-OFDM BPSK 20MHz 1RB 104offset 351500ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, n66 (0); Frequency: 1757.5 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3049; ; Calibrated: 2020-05-26 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -46.60 dBA/m Location: -8.3, 0, 3.7 mm F-TP22-03 (Rev.00) 238 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.193 NR Band66 DFT-s-OFDM BPSK 20MHz 1RB 104offset 354000ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, n66 (0); Frequency: 1770 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3049; ; Calibrated: 2020-05-26 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -43.50 dBA/m Location: 8.3, 8.3, 3.7 mm F-TP22-03 (Rev.00) 239 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.194 NR Band66 DFT-s-OFDM BPSK 20MHz 1RB 104offset 354000ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, n66 (0); Frequency: 1770 MHz;Duty Cycle: 1:1 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3049; ; Calibrated: 2020-05-26 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE4 Sn868; Calibrated: 2019-09-04 Phantom: HAC Test Arch with AMCC TCOIL Measurement SW: DASY52, Version 52.10 (4); T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -46.86 dBA/m Location: -8.3, 0, 3.7 mm F-TP22-03 (Rev.00) 240 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.195 NR Band41 DFT-s-OFDM BPSK 20MHz 1RB 49offset 518598ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, n41 (0); Frequency: 2592.99 MHz;Duty Cycle: 1:4 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3050; ; Calibrated: 11/20/2019 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2/26/2020 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -43.41 dBA/m Location: 8.3, 8.3, 3.7 mm F-TP22-03 (Rev.00) 241 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.196 NR Band41 DFT-s-OFDM BPSK 20MHz 1RB 49offset 518598ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, n41 (0); Frequency: 2592.99 MHz;Duty Cycle: 1:4 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3050; ; Calibrated: 11/20/2019 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2/26/2020 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -54.29 dBA/m Location: -8.3, 0, 3.7 mm F-TP22-03 (Rev.00) 242 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.197 NR Band41 DFT-s-OFDM BPSK 40MHz 1RB 104offset 518598ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, n41 ; Frequency: 2592.99 MHz;Duty Cycle: 1:4 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3050; ; Calibrated: 11/20/2019 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2/26/2020 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -42.36 dBA/m Location: 8.3, 8.3, 3.7 mm F-TP22-03 (Rev.00) 243 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.198 NR Band41 DFT-s-OFDM BPSK 40MHz 1RB 104offset 518598ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, n41 (0); Frequency: 2592.99 MHz;Duty Cycle: 1:4 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3050; ; Calibrated: 11/20/2019 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2/26/2020 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -54.31 dBA/m Location: -8.3, 0, 3.7 mm F-TP22-03 (Rev.00) 244 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.199 NR Band41 DFT-s-OFDM BPSK 50MHz 1RB 131offset 518598ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, n41 (0); Frequency: 2592.99 MHz;Duty Cycle: 1:4 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3050; ; Calibrated: 11/20/2019 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2/26/2020 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -42.04 dBA/m Location: 8.3, 8.3, 3.7 mm F-TP22-03 (Rev.00) 245 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.200 NR Band41 DFT-s-OFDM BPSK 50MHz 1RB 131offset 518598ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, n41 (0); Frequency: 2592.99 MHz;Duty Cycle: 1:4 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3050; ; Calibrated: 11/20/2019 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2/26/2020 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -54.43 dBA/m Location: -8.3, 0, 3.7 mm F-TP22-03 (Rev.00) 246 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.201 NR Band41 DFT-s-OFDM BPSK 60MHz 1RB 160offset 518598ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, n41 (0); Frequency: 2592.99 MHz;Duty Cycle: 1:4 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3050; ; Calibrated: 11/20/2019 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2/26/2020 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -54.18 dBA/m Location: 8.3, 8.3, 3.7 mm F-TP22-03 (Rev.00) 247 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.202 NR Band41 DFT-s-OFDM BPSK 60MHz 1RB 160offset 518598ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, n41 (0); Frequency: 2592.99 MHz;Duty Cycle: 1:4 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3050; ; Calibrated: 11/20/2019 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2/26/2020 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Interpolated Noise Spectrum(x,y,z,f) (121x121x1): Interpolated grid: dx=1.000 mm, dy=1.000 mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -54.96 dBA/m Location: -8.3, 0, 3.7 mm F-TP22-03 (Rev.00) 248 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.203 NR Band41 DFT-s-OFDM BPSK 80MHz 1RB 215offset 518598ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, n41 (0); Frequency: 2592.99 MHz;Duty Cycle: 1:4 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3050; ; Calibrated: 11/20/2019 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2/26/2020 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -53.89 dBA/m Location: 8.3, 8.3, 3.7 mm F-TP22-03 (Rev.00) 249 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.204 NR Band41 DFT-s-OFDM BPSK 80MHz 1RB 215offset 518598ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, n41 (0); Frequency: 2592.99 MHz;Duty Cycle: 1:4 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3050; ; Calibrated: 11/20/2019 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2/26/2020 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -54.94 dBA/m Location: -8.3, 0, 3.7 mm F-TP22-03 (Rev.00) 250 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.205 NR Band41 DFT-s-OFDM BPSK 90MHz 1RB 243offset 518598ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, n41 (0); Frequency: 2592.99 MHz;Duty Cycle: 1:4 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3050; ; Calibrated: 11/20/2019 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2/26/2020 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -53.53 dBA/m Location: 8.3, 8.3, 3.7 mm F-TP22-03 (Rev.00) 251 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.206 NR Band41 DFT-s-OFDM BPSK 90MHz 1RB 243offset 518598ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, n41 (0); Frequency: 2592.99 MHz;Duty Cycle: 1:4 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3050; ; Calibrated: 11/20/2019 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2/26/2020 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -55.04 dBA/m Location: -8.3, 0, 3.7 mm F-TP22-03 (Rev.00) 252 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.207 NR Band41 DFT-s-OFDM BPSK 100MHz 1RB 271offset 518598ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, n41 (0); Frequency: 2592.99 MHz;Duty Cycle: 1:4 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3050; ; Calibrated: 11/20/2019 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2/26/2020 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -54.24 dBA/m Location: 8.3, 8.3, 3.7 mm F-TP22-03 (Rev.00) 253 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.208 NR Band41 DFT-s-OFDM BPSK 100MHz 1RB 271offset 518598ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, n41 (0); Frequency: 2592.99 MHz;Duty Cycle: 1:4 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3050; ; Calibrated: 11/20/2019 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2/26/2020 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -55.04 dBA/m Location: -8.3, 0, 3.7 mm F-TP22-03 (Rev.00) 254 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.209 NR Band41 DFT-s-OFDM BPSK 20MHz 1RB 49offset 501204ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, n41 (0); Frequency: 2592.99 MHz;Duty Cycle: 1:4 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3050; ; Calibrated: 11/20/2019 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2/26/2020 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -42.13 dBA/m Location: 8.3, 8.3, 3.7 mm F-TP22-03 (Rev.00) 255 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.210 NR Band41 DFT-s-OFDM BPSK 20MHz 1RB 49offset 501204ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, n41 (0); Frequency: 2506.02 MHz;Duty Cycle: 1:4 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3050; ; Calibrated: 11/20/2019 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2/26/2020 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -54.44 dBA/m Location: -8.3, 0, 3.7 mm F-TP22-03 (Rev.00) 256 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.211 NR Band41 DFT-s-OFDM BPSK 20MHz 1RB 49offset 509898ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, n41 (0); Frequency: 2592.99 MHz;Duty Cycle: 1:4 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3050; ; Calibrated: 11/20/2019 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2/26/2020 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -42.20 dBA/m Location: 8.3, 8.3, 3.7 mm F-TP22-03 (Rev.00) 257 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.212 NR Band41 DFT-s-OFDM BPSK 20MHz 1RB 49offset 509898ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, n41 (0); Frequency: 2592.99 MHz;Duty Cycle: 1:4 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3050; ; Calibrated: 11/20/2019 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2/26/2020 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -54.33 dBA/m Location: -8.3, 0, 3.7 mm F-TP22-03 (Rev.00) 258 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.213 NR Band41 DFT-s-OFDM BPSK 20MHz 1RB 49offset 509898ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, n41 (0); Frequency: 2592.99 MHz;Duty Cycle: 1:4 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3050; ; Calibrated: 11/20/2019 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2/26/2020 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -42.24 dBA/m Location: 8.3, 8.3, 3.7 mm F-TP22-03 (Rev.00) 259 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.214 NR Band41 DFT-s-OFDM BPSK 20MHz 1RB 49offset 509898ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, n41 (0); Frequency: 2592.99 MHz;Duty Cycle: 1:4 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3050; ; Calibrated: 11/20/2019 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2/26/2020 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -54.54 dBA/m Location: -8.3, 0, 3.7 mm F-TP22-03 (Rev.00) 260 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.215 NR Band41 DFT-s-OFDM BPSK 20MHz 1RB 49offset 535998ch z(axial) DUT: SM-A516U; Type: Bar Communication System: UID 0, n41 (0); Frequency: 2592.99 MHz;Duty Cycle: 1:4 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3050; ; Calibrated: 11/20/2019 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2/26/2020 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/z (axial) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -41.79 dBA/m Location: 8.3, 8.3, 3.7 mm F-TP22-03 (Rev.00) 261 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Plot No.216 NR Band41 DFT-s-OFDM BPSK 20MHz 1RB 49offset 535998ch y(transversal) DUT: SM-A516U; Type: Bar Communication System: UID 0, n41 (0); Frequency: 2592.99 MHz;Duty Cycle: 1:4 Medium parameters used: = 0 S/m, r = 1; = 0 kg/m3 Phantom section: TCoil Section DASY5 Configuration: Probe: AM1DV3 - 3050; ; Calibrated: 11/20/2019 Sensor-Surface: 0mm (Fix Surface) Electronics: DAE3 Sn504; Calibrated: 2/26/2020 Phantom: HAC Test Arch with AMCC Measurement SW: DASY52, Version 52.10 (4); SEMCAD X Version 14.6.14 (7483) T-Coil scan (scan for ANSI C63.19-2007 & 2011 compliance)/General Scans/y (transversal) 4.2mm 50 x 50/ABM Noise Spectrum(x,y,z,f) (13x13x1): Measurement grid: dx=10mm, dy=10mm Signal Type: Audio File (.wav) 48k_voice_1kHz_1s.wav Output Gain: 20.21 Measure Window Start: 300ms Measure Window Length: 1000ms Device Reference Point: 0, 0, -6.3 mm Cursor: ABM = -54.27 dBA/m Location: -8.3, 0, 3.7 mm F-TP22-03 (Rev.00) 262 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 Attachment 2. HAC T-Coil Probe Certificates F-TP22-03 (Rev.00) 263 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 F-TP22-03 (Rev.00) 264 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 F-TP22-03 (Rev.00) 265 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 F-TP22-03 (Rev.00) 266 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 F-TP22-03 (Rev.00) 267 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 F-TP22-03 (Rev.00) 268 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 F-TP22-03 (Rev.00) 269 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 F-TP22-03 (Rev.00) 270 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 F-TP22-03 (Rev.00) 271 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 F-TP22-03 (Rev.00) 272 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 F-TP22-03 (Rev.00) 273 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 F-TP22-03 (Rev.00) 274 / 275 HCT CO.,LTD. Report No: HCT-SR-2006-FC006-R1 F-TP22-03 (Rev.00) 275 / 275 HCT CO.,LTD.Microsoft Word 2016